Caterpillar Cat 637G Wheel Scraper (Prefix DEY) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
637G Wheel Tractor

Shutdown SIS
Previous Screen
Product: WHEEL SCRAPER
Model: 637G WHEEL SCRAPER DEY
Configuration: 637G Wheel Scraper Coal Bowl DEY00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
637G Wheel Tractor-Scraper
Wheel Scraper Power Train
Media Number -RENR8606-00 Publication Date -01/04/2006 Date Updated -21/04/2006
i04332691
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-1861 Retaining Ring Pliers 1
C 1P-0520 Driver Gp 1
D 2P-8312
Retaining Ring Pliers
(External)
1
E 8H-0663
Bearing Puller Gp
(Nine Ton Capacity)
1
F
1P-2322
Combination Puller
(Two Jaw or Three Jaw)
1
1P-0546 Puller Jaw 1
1P-0510 Driver Gp 1
Start By:
a. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter, Transmission and Transfer Gear - Separate".
1/11(W)
w
2021/6/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00833596
1. Remove retaining ring (1). Remove retarder rotor (2).
2. Remove seal ring (4) from carrier (3) on each side of retarder rotor (2).
3. Remove carrier (3).
2/11(W)
w
2021/6/26

Note: The carrier will be destroyed when the carrier is removed from the retarder.
4. Remove bolts (5). Remove race (6).
5. Attach Tooling (A) and a suitable lifting device to housing assembly (7). The weight of
housing assembly (7) is approximately 73 kg (160 lb).
6. Remove housing assembly (7) from the torque converter.
3/11(W)
w
2021/6/26

7. Position housing assembly (7), as shown.
8. Remove bolts (9). Remove gear (8).
9. Use Tooling (B) to remove retaining ring (10) from each side of gear (8).
10. Remove shaft (11).
4/11(W)
w
2021/6/26

11. Use a suitable press and Tooling (C) to remove the bearing from gear (8).
12. Remove bolts (12). Remove housing assembly (13).
13. Remove piston (14) from housing assembly (13). Remove seals (15).
5/11(W)
w
2021/6/26

14. Remove disc assembly (16).
15. Remove retainer (17) from shaft (22). Remove ring seals (18).
16. Remove gear (19) from shaft (22).
17. Remove bolts (20) and retainer (21). Use Tooling (D) to remove retaining ring (23).
6/11(W)
w
2021/6/26

18. Position the torque converter, as shown. Remove bolts (24).
19. Attach Tooling (A) and a suitable lifting device to impeller assembly (25). The weight of
impeller assembly (25) is approximately 41 kg (90 lb).
20. Remove impeller assembly (25) from housing (26).
21. Remove retaining ring (27) and the bearing.
7/11(W)
w
2021/6/26

22. Use Tooling (F) to separate shaft (22) from carrier assembly (28) and the bearing. Remove
the bearing.
23. Remove bolts (29). Remove stator assembly (31) from impeller (30).
8/11(W)
w
2021/6/26

24. Remove bolts (32) from gear (33).
25. Use Tooling (B) to drive carrier assembly (28) and gear (33) out of impeller (30).
26. Use Tooling (B) to drive carrier (34) out of impeller (30).
27. Use Tooling (B) to drive carrier assembly (28) out of bearing (35).
9/11(W)
w
2021/6/26

28. Remove gear (33) from carrier assembly (28).
29. Remove seal ring (36).
30. Remove rings (37). Use Tooling (D) to remove ring (38) from shaft (22).
10/11(W)
w
2021/6/26

31. Install Tooling (E). Tooling (E) must be seated on the shoulders of turbine (39). Tooling (E)
must not contact the splines on shaft (22).
Note: Tooling (E) must be used in order to support turbine (39) or damage to turbine (39)
will result.
32. Use a suitable press to remove shaft (22) from turbine (39). Remove bearing race (40) and
the spacer from turbine (39).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 26 16:17:10 UTC+0800 2021
11/11(W)
w
2021/6/26

Shutdown SIS
Previous Screen
i02322407
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
A 138-7575 Link Bracket 3
B 1P-1861 Retaining Ring Pliers 1
C 1P-0520 Driver Gp 1
D 2P-8312
Retaining Ring Pliers
(External)
1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/10(W)
w
2021/6/26

1. Lower the temperature of shaft (22). Use Tooling (D) to install ring (38). Install shaft (22) in
the turbine until ring (38) rests on the turbine. Install rings (37).
2. Install the spacer. Raise the temperature of bearing race (40). Install bearing race (40) to
turbine (39) and shaft (22).
3. Install seal ring (36).
2/10(W)
w
2021/6/26

4. Install gear (33) to carrier assembly (28).
5. Raise the temperature of bearing (35). Install bearing (35) on carrier assembly (28).
6. Lower the temperature of carrier (34). Install carrier (34) into impeller (30).
Note: Make sure that the bolt holes are aligned.
3/10(W)
w
2021/6/26

7. Position gear (33). Install bolts (32). Tighten bolts (32) to a torque of 50 ± 7 N·m
(37 ± 5 lb ft).
8. Position stator assembly (31) on impeller (30) and on carrier assembly (28). Install bolts
(29). Tighten bolts (29) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
9. Install carrier assembly (28) on impeller (39).
4/10(W)
w
2021/6/26

10. Raise the temperature of the bearing. Install the bearing on shaft (22).
11. Lower the temperature of the bearing. Install the bearing. Install retaining ring (27).
12. Use Tooling (A) and a suitable lifting device to install impeller assembly (25) to housing
(26). The weight of impeller assembly (25) is approximately 41 kg (90 lb).
5/10(W)
w
2021/6/26

13. Position the torque converter, as shown. Install bolts (24). Tighten bolts (24) to a torque of
30 ± 5 N·m (22 ± 4 lb ft).
14. Use Tooling (D) to install retaining ring (23). Position retainer (21). Install bolts (20).
Tighten bolts (20) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
15. Install gear (19) on shaft (22).
6/10(W)
w
2021/6/26

16. Install ring seals (18). Install retainer (17) on shaft (22).
17. Install disc assembly (16).
18. Install seals (15). Install piston (14) into housing assembly (13).
19. Install housing assembly (13).
7/10(W)
w
2021/6/26

20. Install bolts (12). Tighten bolts (12) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
21. Use a suitable press and Tooling (C) to install the bearing to gear (8).
22. Install shaft (11).
23. Use Tooling (B) to install retaining ring (10) on each side of gear (8).
8/10(W)
w
2021/6/26

24. Position housing assembly (7), as shown.
25. Position gear (8). Install bolts (9).
26. Attach Tooling (A) and a suitable lifting device to housing assembly (7). The weight of
housing assembly (7) is approximately 73 kg (160 lb).
27. Install housing assembly (7) onto the torque converter.
9/10(W)
w
2021/6/26

28. Install race (6). Install bolts (5).
29. Install carrier (3).
30. Install seal ring (4) to carrier (3) on each side of retarder rotor (2).
31. Install retarder rotor (2). Install retaining ring (1).
End By:
a. Connect the torque converter to the transmission. Refer to Disassembly and Assembly,
"Torque Converter, Transmission and Transfer Gear - Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jun 26 16:18:06 UTC+0800 2021
10/10(W)
w
2021/6/26

Shutdown SIS
Previous Screen
i02331325
Transfer Gears - Disassemble
SMCS - 3159-015
Disassembly Procedure
Table 1
Required Tools
A 1P-0520 Driver Gp 1
B
1P-0820 Hydraulic Puller 1
3H-0465 Push-Puller Plate 4
8B-7549 Puller Leg 2
8B-7551 Bearing Puller Gp 1
C 138-7573 Link Bracket 2
D
5F-7343
Bearing Puller Gp
(Twenty Ton Capacity)
1
1P-0520 Driver Gp 1
E
8B-7551 Bearing Puller Gp 1
1P-0520 Driver Gp 1
Start By:
A. Remove the transmission. Refer to Disassembly and Assembly, "Torque Converter,
Transmission, and Transfer Gear - Separate".
1/9(W)
w
2021/6/26

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Remove cover (1) .
2/9(W)
w
2021/6/26

2. Remove bolt (5). Remove retainer (6). Remove the O-ring seal. Remove yoke (4) .
3. Remove bolts (2). Remove cage assembly (3) .
4. Remove seal (7) from cage assembly (3) .
3/9(W)
w
2021/6/26

5. Position cage assembly (3). Remove bolts (8). Remove plate (9). Remove O-ring seal (10) .
6. Use Tooling (A) and a suitable press in order to remove bearings (11) from cage assembly
(3) .
4/9(W)
w
2021/6/26

Note: If the shaft is not supported, the shaft will fall when bolt (13) is removed.
7. Position transfer case (12). Support shaft (14). Remove bolt (13). Remove the retainer.
Remove shaft (14) .
8. Remove gear (15) from transfer case (12) .
9. Use Tooling (B) in order to remove bearing (16) from shaft (14) .
10. Remove bolts (17) .
5/9(W)
w
2021/6/26

11. Attach Tooling (C) and a suitable lifting device to cage (18). Remove cage (18) and the
pinion as a unit. The weight of cage (18) and the pinion is approximately 34 kg (76 lb).
12. Remove bolts (19). Remove plate (20). Remove bearing cone (21) .
6/9(W)
w
2021/6/26

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

13. Use Tooling (D) and a suitable press in order to remove cage (18) from pinion (22) .
14. If necessary, use Tooling (E) in order to remove bearing cone (23) from pinion (22). If
necessary, use Tooling (E) in order to remove bearing cone (24) from pinion (22) .
15. Remove retaining ring (25) in order to remove bearing cup (26) from cage (18) .
7/9(W)
w
2021/6/26

16. Use Tooling (A) and a suitable press in order to remove the bearing cup from cage (18) .
17. Remove plug (27). Remove the dowel that holds the race in position.
18. Remove bearing race (28). Remove bearing race (29) .
8/9(W)
w
2021/6/26

Caterpillar Cat 637G Wheel Scraper (Prefix DEY) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 637G Wheel Scraper (Prefix DEY) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 637G Wheel Scraper (Prefix DEY) Service Repair Manual Instant Download.pdf (7)

More from 9fikslkddmd8u

More from 9fikslkddmd8u (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 637G Wheel Scraper (Prefix DEY) Service Repair Manual Instant Download.pdf