needle punched non-woven impregnated with water absorbing and water swelling polymers

1. EasySeal / SilverSeal interplastics
Technical Data Sheet Trading and Development GmbH
Needle punched non-woven impregnated with water absorbing
and water swelling polymer
Product description
CEMproof® EasySeal is a “light-weight” waterproofing system for the use in any water-sealing applications.
CEMproof® EasySeal is a needle punched non-woven impregnated with water absorbing and water swelling polymer.
SilverSeal is the modified EasySeal with a UV-resistant PE-sheet extruded on top of the needle punched
swelling and water-reactive non-woven!
The self healing properties of the hydrophilic, waterreactive polymers secure the integrity of the system even when
the system is damaged during installation. Penetrating water causes the polymers to swell and thus renders the
CEMproof® EasySeal impermeable. The building structure is permanently protected against penetrating water, even
small cracks and voids in the concrete are sealed.
CEMproof® EasySeal can also be used in salt water areas!
Areas of use
CEMproof EasySeal is used in all applications, where structures have to be protected against groundwater and
seepage. For the waterproofing of foundations, basements, tunnels, garages and flat roofs CEMproof EasySeal is an
economically and environmentally sound alternative to synthetic liners, bituminous products and coatings.
Advantages
• Tough and resistant, high compound shear strength
• Quick and easy to install
• Can be installed in every season, independently of temperature and weather condition
• No need for complicated welding equipment or specially trained personnel
• Quality controlled
• Self healing properties by the pressure of the swelling polymers
• Seals small cracks in the concrete by the pressure of the swelling SAP
• Flexibility in roll dimensions (2,00m x 50,00m)
• Can be used in salt water conditions
• Tests have been made at the University of Braunschweig/Germany
• Easy handling of CEMproof EasySeal because of the extreme light weight
• Enormous water absorbing capacity and therefore enormous swelling and sealing capacity
because of embedded HSAP = High Swelling Absorbing Polymer
Technical information:
interplastics Trading and Development GmbH
A-2601 Sollenau, Wiener Str. 50/8/3, Phone: + 43 676 970 6745, E-Mail: harald.lindorfer@aon.at

2. interplastics
Technical Data Sheet Trading and Development GmbH
EasySeal / SilverSeal
Technical Data
Name of Product EasySeal swelling nonwoven
Type Needle punched nonwoven,
impregnated
Raw material Polypropylene fibres,
white
Swelling material water absorbing, swelling
polymer
Mass per Unit Area ( g/m²) dry / wet after EN 965
swelling / re-dried 450 / 8200 / 400
Thickness at surcharge 2 kN/m² EN 964
(mm) dry / wet after swelling / redried 1,9 / 7,5 / 4,5
Surcharge 20 kN/m² / 200 kN/m²; 2,2 / 1,3
Summary:
(mm) dry The typ of the water contact has a strong
Maximum tensile force (kN/m) EN 1031 influence of the water-penetration along and
dry / wet after swelling / re-dried 11,6 / 3,4 / 10,3 through EasySeal / SilverSeal swelling non-
woven. The water constancy (alkaline water,
associated elongation % EN 10319 salt water a.s.o.) has no marginal influence
dry / wet after swelling / re-dried 69 / 117 / 92 of the waterpenetration along and through
EasySeal / SilverSeal swelling non-woven.
Static puncture test (kN) EN 12236 (See actual test report of the Technical
dry / wet after swelling / re-dried 1,7 / 1,0 / 1,6 University BS /Germany!)
Associated movement of plunger EN 12236
(cm) dry / wet after swelling / re-dried 6,1 / 10,8 / 6,1 EasySeal / SilverSeal swelling
Class of Robustness GRK 3 non-woven is an unique,
Testing of swelling pressure (kN/m²) > 190
patented technology made in
Germany.
Water permeability DIN 18130 TX-KP-STUO
Initial swelling < 5 x 10-9 Overlapping areas are glued with CEM 805
together and are absolutely waterproof sealed
Dry-Wet-Testing < 3 x 10-9 up to 2.5 bar waterpressure (see several
different test reports of different public
Frost-thaw-cycle ( 4 cycles ) < 3,9 x 10-9
laboratories)!
Disclaimer:
The general information provided in the present technical description, application guidelines and other recommendations,
is based on research and experience. However the client is obliged to determine himself what products are suitable for use.
Accordingly, no liability will be accepted by interplastics Trading and Development GmbH.
Technical information:
interplastics Trading and Development GmbH
A-2601 Sollenau, Wiener Str. 50/8/3, Phone: + 43 676 970 6745, E-Mail: harald.lindorfer@aon.at