• Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
    Be the first to like this
No Downloads

Views

Total Views
805
On Slideshare
0
From Embeds
0
Number of Embeds
1

Actions

Shares
Downloads
4
Comments
0
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. EXPERIMENT NO 5 You have just been asked to build a lab network to test new configurations that will be rolled out to your production networks. Host A on left should be setup with ip of 192.168.101.2/24 and a default gateway of 192.168.101.1/24 Host B on right should be setup with ip of 192.168.100.2/24 and a default gateway of 192.168.100.1/24 R1(Router) Ethernet Interface 192.168.101.1/24 Serial interface 192.168.1.1/24 R2(Router) Ethernet Interface 192.168.100.1/24 Serial interface 192.168.1.2/24 We have DCE cable connected at R1 with speed of 64K Configure the devices with host names and make sure they can ping any device that are directly connected R1 Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z Router(config)#interface s0/0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#clock rate 64000 Router(config-if)#no shutdown 10:15:54 %LINK-3-UPDOWN: Interface Serial0/0, changed state to up 10:15:54 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up Router(config-if)#exit Router(config)#interface f0/0 Router(config-if)#ip address 192.168.101.1 255.255.255.0 Router(config-if)#no shutdown 10:17:09 %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up 10:17:09 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit R2 Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z Router(config)#interface s0/0 Router(config-if)#ip address 192.168.1.2 255.255.255.0
  • 2. Router(config-if)#no shutdown 10:15:54 %LINK-3-UPDOWN: Interface Serial0/0, changed state to up 10:15:54 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up Router(config-if)#exit Router(config)#interface f0/0 Router(config-if)#ip address 192.168.100.1 255.255.255.0 Router(config-if)#no shutdown 10:17:09 %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up 10:17:09 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Router(config-if)#exit PINGING DEVICES C:>ping 192.168.100.1 Pinging 192.168.100.1 with 32 bytes of data: Reply from 192.168.100.1 ;bytes=32 time=22ms TTL=254 Reply from 192.168.100.1 ;bytes=32 time=22ms TTL=254 Reply from 192.168.100.1 ;bytes=32 time=22ms TTL=254 Reply from 192.168.100.1 ;bytes=32 time=22ms TTL=254 Ping Statistics for 192.168.100.1: Packets Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 22ms, Maximum = 23ms, Average = 22ms
  • 3. OUTPUT AT VISUALIZER