This is an ideal sized compact digital level that also incorporates the bubble. At 8 inches with 0.1 Degree Resolution. It's LCD display is easy to read with measurements in either degrees and percentages. 1 horizontal and 1 vertical vial. Buzzer Sound at 0, 90 and when you hold a reading Hold Function to freeze display on current reading Long Battery Life with 3 minutes auto off. Built in strong magnet base to firmly hold on flat and pipe surfaces High accuracy of 0.1 degrees at 0° and 90° and 0.2 degrees at all other angles Switchable display between degrees (°) or slope (%) Strong magnet on the base enable the level to be fixed on to any magnetic surface Buzzer sound at 0° Measurement Range 0° ~ +/- 90° x 4 (360°)

1. Model DWL 200 Series
The DWL 200 is a 200 mm length Digital Mini Level. The strong impact resistance ABS
plastic material is molded with a tough Aluminium base to form the rugged yet elegant
body structure.
Features & Specification:
Models Special Feature
 Displayed in Degrees (° or slope (%)
)
DWL 200 Resolution 0.1°
• Measurement Range 0° ~ +/- 90°
 High Resolution 0.05°~ 0.1° DWL 280 Resolution 0.05°~ 0.1°
• Operating Temperature 0° ~ 50° C Dimension L(200) x H(42.5) x T(18) mm
• Long Battery Life with 3 minutes auto off
• Easy, Clear & Precise Digital Display
• Hold Function to Freeze Display
• Buzzer Sound
 with Build-in Vials
 With magnet on the base
 Power supply 2 x 3v Lithium cell
(Batteries included)
For further information, please refer to www.digipas.co.uk

2. CALIBRATION INSTRUCTION
Caution: Digi-Pas is calibrated in the Factory for OPERATION
maximum accuracy. User only recalibrate unless a) Batteries:
necessary.  Open the battery compartment at the
rare of the Digi-Pas .
1. Push ONCE on the Cal button then  Remove the small plastic from two new
release.Buzzer starts to beep. batteries (type AAA/LR03).
2a. Place Digi-Pas on a flat surface (e.g. Table)  Ensure correct polarity.
Use a finger to Press Mode button ONCE while b) Switching on the Digi-Pas:
wait a few seconds until buzzer beeps.  Switch the Digi-Pas on using the on/off
b. Place Digi-Pas reverse horizontal (180° Press
) switch.
Mode button ONCE and wait a few seconds until  The Digi-Pas can measure angles range
buzzer beeps. 0°~ +/- 90°
c. Place Digi-Pas vertically (-90° and Press
)  press mode button to choose the
Mode button ONCE and wait a few seconds until resolution in degree or slope angle (If
buzzer beeps. slopes are measured)
d. Place Digi-Pas reverse vertically (+90° and
) c) Buzzer Sound (Acoustic signal):
Press Mode button ONCE and wait a few seconds  The Buzzer Sound are used to indicated
until buzzer beeps. angle of slope stands at 0° 45° 90°
, , .
3. Calibration completes when buzzer beep  To switch off Acoustic signal, hold the
sound stops. Mode for more than 2 seconds, the
NOTE : Ensure Digi-pas is kept still during speaker enunciator will be disappeared.
Calibration
d) Magnets on the based
 The Digi-Pas can be affixed to any
magnetic surface.
e) Hold button (Memory functions)
 With the hold button, you can Freeze
Display for reading and the current
measurement result can be saved in the
internal memory.
 Return to normal measuring mode by
pressing Hold button
 To call back the reading in the internal
memory, press Hold button for 3 second.
The previous save reading will be
appearing in the display.
f) Switching off:
 To switch off the Digi-Pas, press the
on/off switch .When not in use more
than 3 min, the Digi-Pas will switches off
automatically.
UK and Europe sales office
Tarax Technology Limited
First Floor, Office 2,
10 Panmure Street,
Dundee,
DD1 2BW.
e:Info@digipas.co.uk
w:www.digipas.co.uk
m:(+44)07825041403
For further information, please refer to www.digipas.co.uk