Your SlideShare is downloading. ×
  • Like
Axkid Kidzofix handleiding (eng)
Upcoming SlideShare
Loading in...5
×

Thanks for flagging this SlideShare!

Oops! An error has occurred.

×

Now you can save presentations on your phone or tablet

Available for both IPhone and Android

Text the download link to your phone

Standard text messaging rates apply

Axkid Kidzofix handleiding (eng)

  • 217 views
Published

De handleiding van de Axkid Kidzofix in Engelse uitvoering. Hierin is te lezen hoe de stoel geïnstalleerd kan worden en andere zaken met betrekking tot dit Axkid autostoeltje.

De handleiding van de Axkid Kidzofix in Engelse uitvoering. Hierin is te lezen hoe de stoel geïnstalleerd kan worden en andere zaken met betrekking tot dit Axkid autostoeltje.

  • Full Name Full Name Comment goes here.
    Are you sure you want to
    Your message goes here
    Be the first to comment
    Be the first to like this
No Downloads

Views

Total Views
217
On SlideShare
0
From Embeds
0
Number of Embeds
0

Actions

Shares
Downloads
3
Comments
0
Likes
0

Embeds 0

No embeds

Report content

Flagged as inappropriate Flag as inappropriate
Flag as inappropriate

Select your reason for flagging this presentation as inappropriate.

Cancel
    No notes for slide

Transcript

  • 1. Kidzofix Instruction manual Rearward facing with Isofix 9 - 18 kilo Rearward facing with seat belt 9 - 25 kilo Tested and approved according to ECE R44 / 04 Isofix size C/R3 Forward facing with seat belt 9 - 18 kilo Forward facing with adult belt 15 - 25 kilo
  • 2. Thank you for choosing a child seat from Axon Kids. The team developing Kidzo- fix have more than 30 years of experience in child safety products between us, and we have done our outmost to make this child seat as safe as possible. The Kidzofix child seat has of course also been tested and certified according to ECE R/44 04, the latest European standard for child safety. To maximize your child’s safety, please observe the following: Read this instruction manual before assemble the child seat in the car. Read the instructions thoroughly before you attempt to install the child seat. If you have any doubts, please contact your store of purchase, which can show you the correct installation. Incor- rect installation means danger to your child. Never mount the child seat in a seat with an active airbag. If you still wish to use the seat, disconnect the airbag at an authorized service center, or if your car is equipped with it, use the key to turn the airbag off. It is important to always note if the car’s in- dicator shows that the airbag is turned off. Keep the child seat facing backwards as long as possible. Studies have shown that the risk for an accident to be fatal for your child is five times higher if your seat is front facing. Always use the support leg when the seat is mounted backwards. The support leg serves a very important safety purpose and is designed to maximize your child’s safety in an accident. In case of a car accident, no matter how small, always replace the car seat. It may have invisible damage that seriously affects your child’s safety. This is also the reason for why you never should by a used child seat. Axon Kids recommendation is that you always should buy a new chair in a store. Important information
  • 3. Contents The Kidzofix child seat is possible to use from when the child is approximately six months, or can sit without support, up to about the age of six. The chair can be mounted in four different ways, depending on your child’s age and size, and if your car has ISOfix attachments or not. A review of the chair’s parts can be found on the next page. On the following pages you will find instructions on how to assemble your chair: Rearward facing assembly with ISOfix If your car has ISOfix attachments, and your child weighs between 9 and 18 kilos (20 to 39 lb), Axon Kids recommends this assembly. Rearward facing fastened with seat belt If your car is not equipped with ISOfix attachments, you can still easily and safely install the seat using the car’s three-point belt. This assembly can be used when the child weighs between 9 and 25 kilos (20 to 55 lb). Forward facing assembly with seatbelt If you want your child to sit forward and it weighs between 9 and 18 kilos, this assembly can be used in all car seats with a three-point belt. Forward facing with adult belt Once the child has become large enough to sit forward and use the car’s three-point belt, you can secure the child restraint and your child by using your Kidzone as a booster seat. This assembly is suitable for children weighing between 15 and 25 kilos. For the safety of you child; Use backwards assembly as long as possible 13 11 8 5 Never use this child seat in a car seat that is not equipped with an ECE Reg 16 approved three-point belt.
  • 4. 1. Belt guide top (Forward facing with internal harness only) 2. Head support 3. Belt guides head support (Forward fac- ing with vehicle 3 point belt) 4. Internal harness. 5. Lower belt guide. (Forward facing with vehicle 3 point belt) 6. Adjuster for internal harness 7. Adjuster arm for seat angel 8. Base 9. ISOfix 10. Tether strap 11. Support leg 12. Adjuster handles for support leg. 13. Heels 14. Adjuster for ISOfix 15. Lock-off 16. Pocket for storing manual 17. Guide for assembly 18. Indicator 19. Release button 16
  • 5. Important to remember Never mount the child seat in a seat with an active frontal airbag. If you still wish to use the seat, disconnect the airbag at an authorized service center, or if your car is equipped with it, use the key to turn the airbag off. It is important to always note if the car’s indicator shows that the airbag is turned off. Place the child seat Before you lift the child seat into the car, start by pressing and holding the locking le- ver (1). Now you can fold out the ISOfix arms (2), located on the bottom side of the child seat. The simplest way to lifting the child seat into the car is with its back first. Place the child seat in the car seat and turn it so that the back is facing the front direction of the car. When mounting the child seat in the car’s front sear, it is possi- ble, but not crucial, for the back of the child seat to have contact with the dashboard. Attach ISOfix-arms There are two ISOfix mounts in every seat of the car. You can find the brackets between the backrest and the seat cushion. The supplementary guides (3), which you will find in the child seat, can help you find Rearward facing with ISOfix Never use the child seat in a car seat where airbag hasn’t been disabled. 5 Continued on next page3 2 1
  • 6. the brackets and also protects upholstery on the cushion. Press the ISOfix arms through the guides and fix them in the car´s mounts. When you hear a click and both indicators (1) are green it is properly secured. If you later wish to remove the car seat, hold down both of the release buttons (2). Push down the lever for adjusting the sit- ting angle (3). With the lever depressed, you can then adjust the seat and choose one of its three tilt positions. The choice of tilt position should be one that is as upright as possible, but the child should be able to keep its head up on its own and the head should not hang forward if the child falls asleep. The rule of thumb is that the older the child grows, the more upright the tilt position can be. Also note that the child seat will be angled down slightly when it is clamped and sinks into the car’s seat. Attach the tether straps Your car may have two eyelets in the front seat rails, or when mounting in the front seat, in front of the same seat. When your car has no eyelet you should in- stead use the supplied strap which is in the child seat. If the child seat is installed in the rear seat, put one end of the strap through either the rear of the front seat rails or an- other suitable fastening point in the front seat. The loop should be as close as possible to the floor. Choose an appropriate length of the strap and then put the loop through one of the openings on the side of the strap. When installing in the front seat the strap 6 1 2 Continued on next page 3 2
  • 7. 7 has to be attached under the seat. Pull out the strap from the anchor roll (4) to an appropriate length. Please check that the white marks on the straps(5) is visible. Otherwise you could try and cross the straps to give them some extra length, white marks will then be visible. Secure the fastening device in the loop of the car or the strap. Repeat on the other side. Wiggle the child seat a few times, easily from side to side.Unfold the sup- port leg (6) to its maximal angle. Pull the latch on the upper length adjuster (7) and pull down the leg so that it gets in con- tact with the car’s floor. If the leg still can- not reach the floor, repeat on the bottom length adjuster (7). Wiggle the chair from side to side a few times more, this time with more power. This will automatically tighten the anchor roll.If you have mounted the child seat in the rear seat of the car, move the front seat to a comfortable location. The seat’s back- side can, but must not, have contact with the car seat. Adjust the seat belt Place the child in the child seat. Place the child’s arms in between the shoul- der straps so that the shoulder straps are hanging over the chest and stomach of the child. Put together the shoulder belts and fasten the buckle between the child’s legs. Pull the adjustment strap (8). This will tighten the belt and the headrest will automatically slide down to the proper height.To loosen the belt, hold down belt adjustment and pull both belts. 44 6 7 8 5
  • 8. Never use the child seat in a car seat where airbag hasn’t been disabled. Rearward facing fastened with seat belt Important to remember Nevermountthechildseatinaseatwith an active airbag. If you still wish to use the seat, disconnect the airbag at an authorized servicecenter,orifyourcarisequippedwith it, use the key to turn the airbag off. It is im- portant to always note if the car’s indicator shows that the airbag is turned off. Place the chair The simplest way to lift the child seat into the car is with its back first. Place the child seat in the car seat and turn it so that the back is facing the front of the car. The heels of the seat (1) should bendovertheedgeoftheseat.Thehighlight onthesideoftheheelshouldalignvertically with the end of the car seat. If you have a small car, and the child is small enough not to require extra leg room, you can instead put the car seat with the heel up on the car seat. When mounting the child seat in the car’s front seat it is possible, but not crucial, for the back of the child seat to have contact with the dashboard. Push down the lever for adjusting the backrest angle (2). With the lever pushed down, you can then adjust the seat and choose one of its three tilt positions. The choice of tilt position should be one that is as upright as possible, but the child should Continued on next page 8 1 2
  • 9. be able to keep its head up on its own, and the head should not hang forward if the child falls asleep. The rule of thumb is that the older the child grows, the more upright the tilt position canbe.Alsonotethatthechildseatwillbeangled down slightly when it is clamped and sinks into the car’s seat. Fasten seat belt in the car Open both belt lock-offs(3) on the child seat. Grasp the seat belt, and pull the belt roll. The lap section of the belt should be at least 70-80 centi- meters (27-32 inch) long. Now place the belt through the hole in (4) andpushitunderthefabricuntilitcomesouton the other side. If you prefer you can instead pull the belt on top of the fabric. Next step is to fasten the seat belt. Tighten the belt firmly, the belt passing through or over the seat should not have any slack. Fasten your belt in belt buckle. In the belt lock-off closest to the car-buckle both lap and shoulder belt should be secured. In the belt lock-off on the opposite side, only the lap belt should be secured. Attach the tether straps Yourcarmayhavetwoeyeletsinthefrontseat rails,orwhenmountinginthefrontseat,infront ofthesameseat.Whenyourcarhasnoeyeletyou should instead use the supplied strap which is in the child seat. If the child seat is installed in the rear seat, put one end of the strap through either the rear of the front seat rails or another suitable fastening point in the front seat. The loop should be as close as possible to the floor. Choose an ap- propriate length of the strap and then put the loop through one of the openings on the side of 9 Continued on next page Skip this part if your car is equipped with eyelets 4 3
  • 10. 10 the strap. When installing in the front seat the strap has to be attached under the seat. Pull out the strap from the anchor roll (1) to an appropriate length. Please check that the white marks on the straps(2) is visible. Otherwise you could try and cross the straps to give them some extra length, white marks will then be visible. Secure the fastening device in the loop of the car or the strap. Repeat on the other side. Wiggle the child seat a few times, easily from side to side. Unfold the support leg (3) to its maximal angle. Pull the latch on the upper length ad- juster (4) and pull down the leg so that it gets in contact with the car’s floor. If the leg still can- notreachthefloor,repeatonthebottomlength adjuster (4). Wiggle the chair from side to side a few times more, this time with more power. This will automatically tighten the anchor roll. If you have mounted the child seat in the rearseatofthecar,movethefrontseattoacom- fortable location. The seat’s backside can, but must not, have contact with the car seat. Adjust the seat belt Place the child in the child seat. Place the child’s arms in between the shoulder straps so that the shoulder straps are hanging over the chestandstomachofthechild.Puttogetherthe shoulder belts and fasten the buckle between the child’s legs. Pull the adjustment strap (5). This will tighten the belt and the headrest will automatically slide down to the proper height. To loosen the belt, hold down belt adjustment and pull both belts. 1 3 4 5 2
  • 11. 11 Forward facing with seatbelt Fixed installation of seat Make sure the seat’s tilt is in its 0-position. If not, hold the adjust- ment lever for its angle (1) change the chair until it stands straight up. Place your Kidzofix on the seat. Pull the car’s safety belt and place the shoulder strap into belt guide(2) on the upper side of the seat. Then pull the belt straight vertically down, on the backside, to the nearest hole in the backseat (3). Lap section of the belt is simultaneously pulled up and guided into the same hole as shoul- der belt. Bring the belts through the hole, across the front of the chair and then back through the second hole (3). Pull both belts horizontally across the side on the chair and then down. Fasten seat belts in the belt buckle and secure it with the lock-off(4). Please make sure that the belts hasn’t tangled up or been folded anywhere. Also make sure that both shoulder and lap belt is securely fastened every- where. Use your own weight to press down the chair in order to automati- cally fasten the seat belt further. Adjust the seat belt Place the child in the child seat. Never use the child seat in a car seat where airbag hasn’t been disabled. Continued on next page Step 1 Step 2 1 3 Step 0 2 4
  • 12. 12 Place the child’s arms in between the shoulder straps so that the shoulder straps is hanging over the chest and stomach of the child. Put together the shoulder belts and fasten the buckle between the child’s legs. Pull the adjustment strap (3). This will tighten the belt and the head- rest will automatically slide down to the proper height. The headrest must always be drawn down at least 35 millimeters. There is a line in the headrest which can be detected with your fingers. If it is behind the cover the headrest has been pulled down correctly. (See picture A) Make sure that the headrest is in the locked position by pulling the belt ad- juster one more time. The headrest shall not move down when you pull the belt. If it is impossible to get the headrest in a locked position, the child seat should instead be used as a booster seat (see next chapter). To loosen the belt, hold down the belt adjuster and pull both belts. Never use the child seat in a car seat where airbag hasn’t been disabled. This line should be hidden behind the cover. 3 Picture A
  • 13. 13 Forward facing with adult belt Important to remember Never mount the child seat in a seat with an active airbag. If you still wish to use the seat, disconnect the airbag at an au- thorized service center, or if your car is equipped with it, use the key to turn the airbagoff.Itisimportanttoalwaysnoteif the car’s indicator shows that the airbag is turnedoff.Since the air bag is designed for adults, it can seriously harm your child in a crash. Remove the seat belt Since you are now going to use car belts, you must first remove the inter- nal child seat belts. Loosen the shoulder straps of the yoke (1) and pull the belt up on the chair. The part passing through the yoke forming a loop, must be attached in the neck rest’s fixing plate(2). After inserting the loop, pull down the retaining plate and the headrest to a height appropriate for your child. Tighten the strap by pulling the belt adjustment (3) in the front of the chair. Make sure the seat’s angle is in its 0-position. If not, hold the lever for adjusting its angle (4) change the chair until it stands straight up. Now your Kidzofix can be used as a booster seat. Continued on next page 1 2 4 Step 1 Step 2 Step 0 3
  • 14. Before your child uses the Kidzofiz child seat make sure that all the steps in this instruction manual has been followed and that the child seat is se- curely fastened. Mount the seat in the car Place Kidzofix child seat in the car’s seat. Then place the child in the child seat. Grab the car’s three-point belt and then guide the shoulder belt through the red belt guide (4), located on the car seat just above the child’s shoulder, and then guide it over the next red mark just above the armrest. You may need to move the chair slightly sideways for the belt to fit comfortably in the seat belt guide. Then move the lap belt through the red belt guides down at the sides of the chair (5) and attach the belt buckle in the car. The belt must not be tangled, twisted or folded at any location and needs to have a firm tension. Picture B is describing the complete belt routing. 14 5 4 Picture B
  • 15. Warranty and handling If the child seat cover is replaced; make sure only to use original products from Axon Kids. If not the safety system could be compromised and may lead to death or injury of your child in case of an accident. The child seat cover can be taken off and washed in the laundry. Use the “handwash”-program or similar (max temp 30 ˚ C ). Do not use the dryer since this can cause the padding to detach from the cloth. Never use the baby seat without it´s cover. The plastic details of the child seat shall be cleaned with a non aggressive cleaning chemicals such as soap water. Aggressive chemicals like solvents etc may cause damage to the material and by this compromise the safety of the child seat. The parts of the child seat can be recycled and shall be sorted in compliance with your local legislation. Ask your local recycling center for advice when recycling the product. Do not do any repairs or make any adjustment to the child seat other then those described in this user guide. Follow closely the installation instructions provided by the child restraint manufacturer. Our warranty policy is inline with your local consumer agency. Make sure to save your receipt and bring it to your dealer if you have any warranty issues. The warranty does not cover: o Wear down as a consequence of normal use. o Damages as a consequence of incorrect use. All our materials keep a very high standard with respect to UV-resistance (sun light). In long term UV light is very aggressive and will lead to that the cloth will be bleached. This is not covered by the warranty since it is considered as normal usage. Never leave your child unattended in the baby seat. Any luggage or other objects liable to cause injuries in the event of a collision shall be properly secured. Store this user manual in the assigned pocket underneath the seat.