The document provides technical specifications and adjustment values for Tandem Rollers models BW 141 AD Serie 4 and BW 154 AD Serie 4. It includes details on the engine, travel pump, travel motors, drum reduction gear, vibration pump, vibration motor, steering and charge pump, and filling capacities. The specifications cover items like engine type, power, cooling, displacement volumes, pressure levels, transmission ratios, and recommended fluid types and quantities.
Bomag bw 141 ad 4 tandem rollers service repair manualpfiskdmjekm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It covers safety regulations, descriptions of indicators and controls, operating instructions, and maintenance procedures. The technical data section provides specifications for each roller model.
Bomag bw 179 pdh 4 single drum rollers service repair manualfjskekdmmem
This document provides technical data and adjustment values for the BW 177 DH Series 4 single drum roller, including specifications for the Deutz diesel engine, hydrostatic travel pump, drum drive motor, vibration pump, steering pump, rear axle, and recommended filling capacities. The machine's serial number range and manufacture dates are also listed to ensure the correct documentation is referenced.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...wedsrffcdgdv
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. It describes using a special tool to press the seal out of and into the front cover. Cleanliness is emphasized to prevent premature wear. The instructions are part of a service manual for Caterpillar C7.1 engines.
Caterpillar cat 950 k wheel loader (prefix fer) service repair manual (fer000...wedsrffcdgdv
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 950K wheel loader. It describes 28 steps to disassemble the steering pump, including removing valves, spools, springs, and other internal components. It then lists 34 steps for reassembling the steering pump. The summary advises checking axial shaft end play during installation and adjusting as needed with a shim.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. It begins by listing the required tools. It then provides step-by-step instructions to disassemble the various components of the pump, including removing seals, springs, valves, and housing pieces. Detailed illustrations accompany each step. Safety notices are included to warn of potential injuries from released springs or pressurized components. The disassembly process yields all individual parts of the pump.
This document provides instructions for removing and installing a piston pump and pump control valve on a 725 Articulated Truck. It outlines 37 steps to disassemble the piston pump, checking components for wear, lubricating seals, and precisely adjusting preload on bearings. It then describes 4 steps to install the piston pump and connect hoses. Finally, it warns of hot oil and pressures in the hydraulic system and lists 1 step to remove identification marks from hoses when removing the pump control valve.
Caterpillar cat 336 f l excavator (prefix yfd) service repair manual (yfd0000...wedsrffcdgdv
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, retaining ring pliers and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Bomag bw 141 ad 4 tandem rollers service repair manualpfiskdmjekm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It covers safety regulations, descriptions of indicators and controls, operating instructions, and maintenance procedures. The technical data section provides specifications for each roller model.
Bomag bw 179 pdh 4 single drum rollers service repair manualfjskekdmmem
This document provides technical data and adjustment values for the BW 177 DH Series 4 single drum roller, including specifications for the Deutz diesel engine, hydrostatic travel pump, drum drive motor, vibration pump, steering pump, rear axle, and recommended filling capacities. The machine's serial number range and manufacture dates are also listed to ensure the correct documentation is referenced.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...wedsrffcdgdv
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. It describes using a special tool to press the seal out of and into the front cover. Cleanliness is emphasized to prevent premature wear. The instructions are part of a service manual for Caterpillar C7.1 engines.
Caterpillar cat 950 k wheel loader (prefix fer) service repair manual (fer000...wedsrffcdgdv
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 950K wheel loader. It describes 28 steps to disassemble the steering pump, including removing valves, spools, springs, and other internal components. It then lists 34 steps for reassembling the steering pump. The summary advises checking axial shaft end play during installation and adjusting as needed with a shim.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. It begins by listing the required tools. It then provides step-by-step instructions to disassemble the various components of the pump, including removing seals, springs, valves, and housing pieces. Detailed illustrations accompany each step. Safety notices are included to warn of potential injuries from released springs or pressurized components. The disassembly process yields all individual parts of the pump.
This document provides instructions for removing and installing a piston pump and pump control valve on a 725 Articulated Truck. It outlines 37 steps to disassemble the piston pump, checking components for wear, lubricating seals, and precisely adjusting preload on bearings. It then describes 4 steps to install the piston pump and connect hoses. Finally, it warns of hot oil and pressures in the hydraulic system and lists 1 step to remove identification marks from hoses when removing the pump control valve.
Caterpillar cat 336 f l excavator (prefix yfd) service repair manual (yfd0000...wedsrffcdgdv
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, retaining ring pliers and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Caterpillar cat 336 f l excavator (prefix lcl) service repair manual (lcl0000...wedsrffcdgdv
This document provides disassembly instructions for a travel motor on a 336F excavator model. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, swashplate, and other internal components. Various tools are required to remove retaining rings, seals, springs, and other parts in the proper sequence. Care must be taken to mark components' locations and ensure springs and other parts are released safely.
Caterpillar cat 336 f l excavator (prefix dsw) service repair manual (dsw0000...wedsrffcdgdv
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety notices advise wearing protective equipment when compressing springs or releasing pressurized components during disassembly.
Caterpillar cat 336 f excavator (prefix yfd) service repair manual (yfd00001 ...wedsrffcdgdv
This document provides instructions to disassemble a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the head, springs, pistons, plates, seals and more. Tools required include bolts, pins, drivers, pullers and stands to safely remove parts and release spring forces. Detailed illustrations accompany each step to show how to disassemble the various systems and components of the travel motor.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety warnings are provided throughout for components under spring pressure.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...wedsrffcdgdv
This document provides instructions for disassembling the travel motor on a 336F and 336F L excavator. The 27-step process includes removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and seals. Special tools are required to remove parts and release spring forces safely. The detailed illustrations and part numbers allow technicians to accurately disassemble and reassemble the travel motor.
Bomag bw 177 single drum rollers service repair manualwedsrffcdgdv
The document provides a maintenance table for a single drum roller that outlines maintenance work to be performed at various operating hour intervals. It lists over 40 maintenance items ranging from daily checks of fluid levels to annual tasks like changing engine oil and filters. Performing regular maintenance according to the schedule is important to ensure the machine is ready for demanding construction work and all safety systems function properly.
Clark esm 12 25 forklift service repair manualwedsrffcdgdv
This document provides maintenance instructions for an electric lift truck. It outlines a planned maintenance program with periodic inspections and maintenance tasks to complete. The inspections and tasks are divided into groups to make the maintenance efficient. Safety practices for maintenance are also described. Completing regular planned maintenance is important for the safe operation and long life of the lift truck.
Clark cq202530 l forklift service repair manualwedsrffcdgdv
The document provides information on servicing and maintaining the CQ20-30 truck transaxle:
- The transaxle construction includes a torque converter, single-speed transmission, differential, drive axle, and drum brakes. Maintenance includes checking fluid levels, changing fluid and filters regularly, and adjusting the service brakes.
- Precautions for disassembly and assembly emphasize cleanliness to prevent contamination. The transaxle has openings for checking fluid levels and draining fluid. Filters should be replaced every 1,000 hours.
- Brake adjustments can be made through openings in the backing plate or wheel hub, aiming for a brake shoe to drum clearance of 0.255-0.304
Clark cq202530 d forklift service repair manualwedsrffcdgdv
The document provides information on servicing the CQ20-30 transaxle:
- It describes the construction of the TA18 transaxle assembly and its components.
- Maintenance procedures are outlined, including checking fluid level and changing fluid and filter every 1,000 hours.
- Pressure specifications and check points for the regulator valve, converter, clutches, and other components are provided.
- The process for adjusting the service brakes via the backing plate or wheel hub opening is described in detail. Cleanliness and proper adjustment are emphasized to prevent issues.
Clark cmp 70 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark cmp 60 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark cmp 50 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar cat d550 b articulated dump truck (prefix 5nd) service repair man...wedsrffcdgdv
This document provides instructions for servicing various components of a Caterpillar 3408 engine, including removing and installing the camshaft, camshaft bearings, timing gears, flywheel, and flywheel housing. The camshaft removal procedure involves using several tools to remove the camshaft gear, camshaft, and dowel. Camshaft bearing removal requires using a tool from the rear of the cylinder block. Timing gear removal involves removing the front balance gear and crankshaft gear. Flywheel removal requires fastening a tool and lifting the flywheel off. Flywheel housing removal requires removing mounting bolts and a bracket.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...wedsrffcdgdv
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety precautions are provided to prevent injury when handling springs or draining fluids.
Caterpillar cat d400 e ii articulated truck (prefix 8ps) service repair manua...wedsrffcdgdv
The document provides instructions for disassembling and assembling the torque converter of a Caterpillar D400E II articulated truck. It describes 38 steps to disassemble the various components of the torque converter including removing the cover, shaft assembly, carrier, impeller, stator, turbine, housing, and piston. It also lists the required tools and provides illustrations for each step. The assembly section instructs to clean all parts thoroughly and inspect them, describing one step to measure clearance with a dial indicator before full assembly.
Caterpillar cat d400 e articulated truck (prefix 2yr) service repair manual (...wedsrffcdgdv
This document provides instructions for disassembling the transmission of a D400E articulated truck powered by a 3406 engine. The disassembly process involves removing over 90 individual parts in a specific sequence, including transmission housings, shafts, gears, seals, springs, and other components. Proper part labeling and organization is important to ensure correct reassembly. Safety precautions are outlined, such as using lifting tools to handle heavy transmission components.
Caterpillar cat d400 d articulated truck (prefix 8tf) service repair manual (...wedsrffcdgdv
This document provides instructions for servicing the transmission control valve and transmission gears of D40D and D400D articulated dump trucks. It describes how to disassemble and assemble the transmission hydraulic control valve by removing its components like spools, springs, and seals. It also details how to disassemble and assemble the input and output transfer gears by removing bearing cages and cones and adjusting end play with shims. The goal is to properly remove, inspect, and reinstall these transmission components.
Caterpillar cat d400 d articulated truck (prefix 2jj) service repair manual (...wedsrffcdgdv
The documents provide instructions for servicing components of articulated dump trucks models D40D and D400D, including:
1) Removing and installing the front hoist control valve by draining hydraulic oil, disconnecting lines and tubes, and removing bolts and pins.
2) Removing and installing the hoist cylinder by relieving pressure, disconnecting hoses, removing bolts and pins, and using straps and a hoist.
3) Disassembling and assembling the front suspension control valve by removing bolts and seals, and inspecting all seals on plugs.
This document provides instructions for removing and installing an output transfer drive on a D400 articulated truck. The removal process involves draining fluids, disconnecting linkages and hoses, and using bolts and pins to separate the drive from the truck frame. Installation is the reverse of removal, and includes reconnecting fluids lines and adjusting linkages. Tolerances and torque specifications are provided for correctly installing components.
Caterpillar cat d350 e ii articulated truck (prefix 2xw) service repair manua...wedsrffcdgdv
This document provides instructions for disassembling and assembling the torque converter of a D350E II articulated truck. It lists 38 steps for disassembling the various components of the torque converter including separating the cover, removing bolts and seals, and pushing/pulling parts out with various tools. It also lists 3 steps for assembling the torque converter, including cleaning all parts, lubricating seals with transmission oil, and checking clearances between components with a dial indicator.
Caterpillar cat 336 f l excavator (prefix lcl) service repair manual (lcl0000...wedsrffcdgdv
This document provides disassembly instructions for a travel motor on a 336F excavator model. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, swashplate, and other internal components. Various tools are required to remove retaining rings, seals, springs, and other parts in the proper sequence. Care must be taken to mark components' locations and ensure springs and other parts are released safely.
Caterpillar cat 336 f l excavator (prefix dsw) service repair manual (dsw0000...wedsrffcdgdv
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety notices advise wearing protective equipment when compressing springs or releasing pressurized components during disassembly.
Caterpillar cat 336 f excavator (prefix yfd) service repair manual (yfd00001 ...wedsrffcdgdv
This document provides instructions to disassemble a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the head, springs, pistons, plates, seals and more. Tools required include bolts, pins, drivers, pullers and stands to safely remove parts and release spring forces. Detailed illustrations accompany each step to show how to disassemble the various systems and components of the travel motor.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety warnings are provided throughout for components under spring pressure.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...wedsrffcdgdv
This document provides instructions for disassembling the travel motor on a 336F and 336F L excavator. The 27-step process includes removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and seals. Special tools are required to remove parts and release spring forces safely. The detailed illustrations and part numbers allow technicians to accurately disassemble and reassemble the travel motor.
Bomag bw 177 single drum rollers service repair manualwedsrffcdgdv
The document provides a maintenance table for a single drum roller that outlines maintenance work to be performed at various operating hour intervals. It lists over 40 maintenance items ranging from daily checks of fluid levels to annual tasks like changing engine oil and filters. Performing regular maintenance according to the schedule is important to ensure the machine is ready for demanding construction work and all safety systems function properly.
Clark esm 12 25 forklift service repair manualwedsrffcdgdv
This document provides maintenance instructions for an electric lift truck. It outlines a planned maintenance program with periodic inspections and maintenance tasks to complete. The inspections and tasks are divided into groups to make the maintenance efficient. Safety practices for maintenance are also described. Completing regular planned maintenance is important for the safe operation and long life of the lift truck.
Clark cq202530 l forklift service repair manualwedsrffcdgdv
The document provides information on servicing and maintaining the CQ20-30 truck transaxle:
- The transaxle construction includes a torque converter, single-speed transmission, differential, drive axle, and drum brakes. Maintenance includes checking fluid levels, changing fluid and filters regularly, and adjusting the service brakes.
- Precautions for disassembly and assembly emphasize cleanliness to prevent contamination. The transaxle has openings for checking fluid levels and draining fluid. Filters should be replaced every 1,000 hours.
- Brake adjustments can be made through openings in the backing plate or wheel hub, aiming for a brake shoe to drum clearance of 0.255-0.304
Clark cq202530 d forklift service repair manualwedsrffcdgdv
The document provides information on servicing the CQ20-30 transaxle:
- It describes the construction of the TA18 transaxle assembly and its components.
- Maintenance procedures are outlined, including checking fluid level and changing fluid and filter every 1,000 hours.
- Pressure specifications and check points for the regulator valve, converter, clutches, and other components are provided.
- The process for adjusting the service brakes via the backing plate or wheel hub opening is described in detail. Cleanliness and proper adjustment are emphasized to prevent issues.
Clark cmp 70 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark cmp 60 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark cmp 50 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar cat d550 b articulated dump truck (prefix 5nd) service repair man...wedsrffcdgdv
This document provides instructions for servicing various components of a Caterpillar 3408 engine, including removing and installing the camshaft, camshaft bearings, timing gears, flywheel, and flywheel housing. The camshaft removal procedure involves using several tools to remove the camshaft gear, camshaft, and dowel. Camshaft bearing removal requires using a tool from the rear of the cylinder block. Timing gear removal involves removing the front balance gear and crankshaft gear. Flywheel removal requires fastening a tool and lifting the flywheel off. Flywheel housing removal requires removing mounting bolts and a bracket.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...wedsrffcdgdv
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety precautions are provided to prevent injury when handling springs or draining fluids.
Caterpillar cat d400 e ii articulated truck (prefix 8ps) service repair manua...wedsrffcdgdv
The document provides instructions for disassembling and assembling the torque converter of a Caterpillar D400E II articulated truck. It describes 38 steps to disassemble the various components of the torque converter including removing the cover, shaft assembly, carrier, impeller, stator, turbine, housing, and piston. It also lists the required tools and provides illustrations for each step. The assembly section instructs to clean all parts thoroughly and inspect them, describing one step to measure clearance with a dial indicator before full assembly.
Caterpillar cat d400 e articulated truck (prefix 2yr) service repair manual (...wedsrffcdgdv
This document provides instructions for disassembling the transmission of a D400E articulated truck powered by a 3406 engine. The disassembly process involves removing over 90 individual parts in a specific sequence, including transmission housings, shafts, gears, seals, springs, and other components. Proper part labeling and organization is important to ensure correct reassembly. Safety precautions are outlined, such as using lifting tools to handle heavy transmission components.
Caterpillar cat d400 d articulated truck (prefix 8tf) service repair manual (...wedsrffcdgdv
This document provides instructions for servicing the transmission control valve and transmission gears of D40D and D400D articulated dump trucks. It describes how to disassemble and assemble the transmission hydraulic control valve by removing its components like spools, springs, and seals. It also details how to disassemble and assemble the input and output transfer gears by removing bearing cages and cones and adjusting end play with shims. The goal is to properly remove, inspect, and reinstall these transmission components.
Caterpillar cat d400 d articulated truck (prefix 2jj) service repair manual (...wedsrffcdgdv
The documents provide instructions for servicing components of articulated dump trucks models D40D and D400D, including:
1) Removing and installing the front hoist control valve by draining hydraulic oil, disconnecting lines and tubes, and removing bolts and pins.
2) Removing and installing the hoist cylinder by relieving pressure, disconnecting hoses, removing bolts and pins, and using straps and a hoist.
3) Disassembling and assembling the front suspension control valve by removing bolts and seals, and inspecting all seals on plugs.
This document provides instructions for removing and installing an output transfer drive on a D400 articulated truck. The removal process involves draining fluids, disconnecting linkages and hoses, and using bolts and pins to separate the drive from the truck frame. Installation is the reverse of removal, and includes reconnecting fluids lines and adjusting linkages. Tolerances and torque specifications are provided for correctly installing components.
Caterpillar cat d350 e ii articulated truck (prefix 2xw) service repair manua...wedsrffcdgdv
This document provides instructions for disassembling and assembling the torque converter of a D350E II articulated truck. It lists 38 steps for disassembling the various components of the torque converter including separating the cover, removing bolts and seals, and pushing/pulling parts out with various tools. It also lists 3 steps for assembling the torque converter, including cleaning all parts, lubricating seals with transmission oil, and checking clearances between components with a dial indicator.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Service Training
BW 141 - 154 AD/AC-4
Table of contents
Foreword A 1
Documentation A 2
General A 3
Technical data and adjustment values B 1
Maintenance C1
Maintenance schedule C2
DEUTZ diesel engine D 1
Operating side/service side D 2
Starter side D 3
Lubrication oil circuit D 4
Coolant circuit D 5
Fuel system D 6
Checking and adjusting the valve clearance D 11
Plug-type injection pump D 14
Electrical components and measuring points on the engine D 30
Travel drive 141/151-4 E 1
Travel pump E 3
Charge pressure relief valve E 9
High pressure relief valve E 10
Pressure override E 12
Travel motors E 15
Drum reduction gear E 18
Test and adjustment points, travel system E 19
Trouble shooting in travel system E 24
Travel drive 154-4 F 1
Travel motors F 7
Drum reduction gear F 8
Flow divider F 11
Test and adjustment points F 19
3. Service Training
BW 141 - 154 AD/AC-4
Vibration G 1
Vibration pump G 3
High pressure relief valves G 6
Control G 7
Vibration motor G 8
Vibration shut-off valve G 9
Drum BW 141 AD-4 G 11
Drum BW 154 AD-4 G 12
Test and adjustment points, vibration system G 14
Trouble shooting in vibration system G 18
Steering system H 1
Steering pump H 3
Priority valve H 4
Steering valve H 5
Articulated joint H 8
Test and adjustment points H 11
Trouble shooting steering system H 14
Working hydraulics - crab walk J 1
Crab walk valve J 2
Test and adjustment points J 3
Blower drive K 1
Water sprinkler system L 1
AC-variant M 1
Electrics with module description O 1
Wiring diagram
Hydraulic diagram
4. Service Training
BW 141 - 154 AD/AC-4 - A 1 -
Foreword
Reliable construction equipment is of greatest advantage for all parties involved:
• for the customer/user it is a basis for an exact calculation of utilization periods and the completion of
projects as scheduled.
• in the rental business it means that the equipment can be reliably used and planned without having
to stock a large number of stand-by machines.
• for the manufacturer it means that customers are satisfied, provides him with a good image and gives
him a feeling of confidence.
It is BOMAG’s philosophy to design and produce the machines with highest possible reliability. This
aspect of simple and easy maintenance was one of the key issues when developing and designing the
machine:
• the location of components in the machine eases maintenance work,
• the high quality standard of BOMAG is the basis for the considerable extension of the service and
maintenance intervals.
• the After Sales Service of BOMAG, including excellent operating and maintenance instruction
manuals, high quality training courses and on-site machine demonstrations helps the customer to
maintain their machines in good condition over a long period of time.
Permanent training of BOMAG’s own service personnel as well as the service personnel of BOMAG
Profit Centres and dealers is therefore a general prerequisite for BOMAG’s excellent world-wide service.
This program of permanent training is only possible with appropriate and up-to-date training material for
trainers as well as persons attending the training courses.
This training manual has not only been written as a support for the professional work of the trainer, but
also for the trainees attending these training courses.
The different levels of product training demand, that the training performed by BOMAG, its Profit Centres
or its dealers reflects the high quality of the training conducted at the Training Centre at BOMAG in
Boppard. For this reason we invested a lot of time in the preparation of these materials .
The structure of this training manual enables us to change or up-date individual chapters in case of
alterations to the machine.
5. Service Training
BW 141 - 154 AD/AC-4 - A 2 -
Documentation
For the BOMAG machines described in this training manual the following documentation is additionally
available:
Attention!
The currently valid part numbers for the documents can be taken from the Doclist or the
Customer Service page in the BOMAG (BOMAG Secured Area) in accordance with the serial
number of the machine.
1. Operating and maintenance instructions
2. Spare parts catalogue
3. Wiring diagram *
4. Hydraulic diagram *
5. Repair instructions
6. Service Information
* The document versions valid at the date of printing are part of this training manual.
6. Service Training
BW 141 - 154 AD/AC-4 - A 3 -
General
The tandem rollers of series BW 141 - 154 AD/AC-4 are high performance machines for the extremely
difficult use in asphalt compaction and earth work.
The machines of this series are powered by engine oil cooled Deutz diesel engines of series BF4M
2011.
Engine driven pumps transfer the engine output power via hydrostatic circuits for travel and vibration
systems to the drums. These hydrostatic drives ensure lowest possible power losses and a high
efficiency. The steering and crab-walk functions as well as the additional edge cutter option are supplied
by gear pumps driven by the auxiliary engine output.
The machines are equipped with a 2 cylinder operated articulated steering and a crab-walk function with
a separate hydraulic cylinder to offset the front frame laterally relative to the rear frame.
For the first time a machine of this product range is equipped with axial piston drum drive motors with
reduction gears The discs of the parking brakes are integrated in the reduction gears. When starting the
engine and opening the brake valve the brakes are relieved by charge pressure. When closing the brake
valve or when shutting the engine down the brakes are automatically applied by spring pressure. These
parking brakes should not be used as service brake, because the deceleration effect is extremely high
and the braking process may damage the brake discs.
The drums are equipped with an exciter shaft and two vibrator units each. The exciter shafts are driven
by hydraulic motors via Bowex couplings. Vibration of the drum is caused by the centrifugal forces
generated by the exciter shaft mounted eccentric weights.
Since the machines are designed for operation with two different frequencies and amplitudes, the sense
of rotation of the exciter shaft can be reversed. Changing the sense of rotation also changes the position
of the change-over weights inside the eccentric weights on the exciter shafts.
This also changes the centrifugal force and the amplitude. The rotary speed of the exciter shaft is also
different to both directions of rotation. This means, that the vibration frequency will also change.
In combination with the hydraulic vibration drive the change-over weights are arranged in such a way,
that the high amplitude works with low frequency and vice-versa.
The combination of high amplitude and low frequency is particularly suitable for compaction work in
earthwork with high lift heights and for preliminary compaction. For soil compaction the combination of
low amplitude and high frequency should be used for the finishing passes.
The individual machine functions like travel system, vibration and steering are described in more detail
in the corresponding chapters. Optional equipment, such as BAM, BOMAG Asphalt Manager
(Variomatic) and chip spreader etc. is not included in this training manual.
7. Service Training
BW 141 - 154 AD/AC-4 - B 1 -
Technical data and adjustment values
The following pages contain technical data valid at the date of printing (see front page of this manual).
Attention!
The currently valid technical data and adjustment values can be taken from the BOMAG Intranet
or Extranet (BOMAG Secured Area) in accordance with the serial number of the machine.
8. BOMAG Central Service - Technical data and adjustment values
Status: 2005-06-22
Product type: BW 141 AD Serie 4
Type No.: 920 00
Serial numbers from: 101 920 00 1001
Engine:
Type: BF4M 2011
Combustion principle: 4-stroke-Diesel
Cooling: Oil
Number of cylinders: 4
Power acc. to ISO 9249: 60 kW
Power data at nominal speed of: 2500 1/min
Low idle speed: 850 +/-150 1/min
High idle speed: 2700+/-50 1/min
Spec. fuel consumption: 245 g/kWh
Valve clearance, inlet: 0,3 mm
Valve clearance, outlet: 0,5 mm
Opening pressure, injection valves: 210 +8 bar
Starter voltage: 12 V
Travel pump:
Type: A4VG 56 HW/32
System: Axial piston-swash plate
Max. displacement: 56 cm3
/U
Max. flow ratio: 136,1 l/min
High pressure limitation: 440 bar
Pressure override: 400+/-10 bar
Charge pressure, high idle: 25 +3/-1 bar
Travel motors:
Type: A2 FE 32
Number: 2
System: Axial piston
Displacement stage 1: 32 cm3
/U
Perm. leak oil quantity: 2 l/min
Flushing quantity: 5 l/min
Reduction gear, drum:
Type: 705 C 2H
Transmission ratio: 48
Number: 2
Vibration pump:
Type: A10VG 45 EZ
System: Axial piston-swash plate
Max. displacement: 45 cm3
/U
Seite 1 von 2
BOMAG Central Service
22.06.2005
http://bsa.bomag.spx.com/bsa/tk_components/english/search_components_result.asp?...
9. Starting pressure: 360+/-20 bar
Operating pressure, soil dependent: ca.100 bar
Vibration motor:
Type: A4FM 22
Number: 2
System: Axial piston-swash plate
Displacement: 22 cm3
/U
Frequency: 40/60 Hz
Amplitude: 0,7/0,34 mm
Steering and charge pump:
Type: HY/ZFFS11/11+8
System: Tandem-/Gear pump
Displacement: 11 / 8 cm3
/U
Max. steering pressure: 200 +/-5 bar
Steering valve:
Type: OSPF 400 LS
System: Rotary valve
Filling capacities:
Engine oil: 13 l (SAE 15W-40, API CG-4 (for details see
maintenance manual))
Hydraulic oil: 60 l (HVLP 46 VI 150)
Vibration bearing housing: 7,5 l (SAE 15W-40, API SJ/CF)
Reduction gear, drum: 1,5 l (SAE 90 EP, API GL 5)
AC refrigerant: 1100 g (R 134a)
Compressor oil (filling the system): 100 ml (PAG Öl)
Seite 2 von 2
BOMAG Central Service
22.06.2005
http://bsa.bomag.spx.com/bsa/tk_components/english/search_components_result.asp?...
10. BOMAG Central Service - Technical data and adjustment values
Status: 2005-06-23
Product type: BW 154 AD Serie 4
Type No.: 920 31
Serial numbers from: 101 920 31 1001
Engine:
Type: BF4M 2011
Combustion principle: 4-stroke-Diesel
Cooling: Oil
Number of cylinders: 4
Power acc. to ISO 9249: 60 kW
Power data at nominal speed of: 2500 1/min
Low idle speed: 850 +/-150 1/min
High idle speed: 2700+/-50 1/min
Spec. fuel consumption: 245 g/kWh
Valve clearance, inlet: 0,3 mm
Valve clearance, outlet: 0,5 mm
Opening pressure, injection valves: 210 +8 bar
Starter voltage: 12 V
Travel pump:
Type: A4VG 56 HW/32
System: Axial piston-swash plate
Max. displacement: 56 cm3/U
Max. flow ratio: 136,1 l/min
High pressure limitation: 440 bar
Pressure override: 400+/-10 bar
Charge pressure, high idle: 25 +3/-1 bar
Travel motors:
Type: A2 FM 32
Number: 4
System: Axial piston
Displacement stage 1: 32 cm3/U
Perm. leak oil quantity: 2 l/min
Reduction gear, drum:
Type: GFT 7 G2801
Transmission ratio: 25,1
Number: 4
Vibration pump:
Type: A10VG 45 EZ
System: Axial piston-swash plate
Max. displacement: 45 cm3/U
Starting pressure: 360+/-20 bar
Seite 1 von 2
BOMAG Central Service
23.06.2005
http://bsa.bomag.spx.com/bsa/tk_components/english/search_components_result.asp?...
11. Operating pressure, soil dependent: ca.100 bar
Vibration motor:
Type: A4FM 22
Number: 2
System: Axial piston-swash plate
Displacement: 22 cm3/U
Frequency: 40/60 Hz
Amplitude: 0,7/0,34 mm
Steering and charge pump:
Type: HY/ZFFS11/11+8
System: Tandem-/Gear pump
Displacement: 11 / 8 cm3/U
Max. steering pressure: 200 +/-5 bar
Steering valve:
Type: OSPF 400 LS
System: Rotary valve
Filling capacities:
Engine oil: 13 l (SAE 15W-40, API CG-4 (for details see
maintenance manual))
Hydraulic oil: 60 l (HVLP 46 VI 150)
Vibration bearing housing: 7,5 l (SAE 15W-40, API SJ/CF)
AC refrigerant: 1100 g (R 134a)
Compressor oil (filling the system): 100 ml (PAG Öl)
Seite 2 von 2
BOMAG Central Service
23.06.2005
http://bsa.bomag.spx.com/bsa/tk_components/english/search_components_result.asp?...
12. BOMAG Central Service - Technical data and adjustment values
Status: 2005-06-22
Product type: BW 154 AD AM Serie 4
Type No.: 920 51
Serial numbers from: 101 920 51 1001
Engine:
Type: BF4M 2011
Combustion principle: 4-stroke-Diesel
Cooling: Oil
Number of cylinders: 4
Power acc. to ISO 9249: 60 kW
Power data at nominal speed of: 2500 1/min
Low idle speed: 850 +/-150 1/min
High idle speed: 2700+/-50 1/min
Spec. fuel consumption: 245 g/kWh
Valve clearance, inlet: 0,3 mm
Valve clearance, outlet: 0,5 mm
Opening pressure, injection valves: 210 +8 bar
Starter voltage: 12 V
Travel pump:
Type: A4VG 56 HW/32
System: Axial piston-swash plate
Max. displacement: 56 cm3
/U
Max. flow ratio: 136,1 l/min
High pressure limitation: 440 bar
Pressure override: 400+/-10 bar
Charge pressure, high idle: 25 +3/-1 bar
Travel motors:
Type: A2 FM 32
Number: 4
System: Axial piston
Displacement stage 1: 32 cm3
/U
Perm. leak oil quantity: 2 l/min
Reduction gear, drum:
Type: GFT 7 G2801
Transmission ratio: 25,1
Number: 4
Vibration pump:
Type: A10VG 45 EZ
System: Axial piston-swash plate
Max. displacement: 45 cm3
/U
Starting pressure: 360+/-20 bar
Seite 1 von 2
BOMAG Central Service
22.06.2005
http://bsa.bomag.spx.com/bsa/tk_components/english/search_components_result.asp?...
13. Operating pressure, soil dependent: ca.100 bar
Vibration motor:
Type: A4FM 28
Number: 1
System: Axial piston-swash plate
Displacement: 28 cm3
/U
Frequency: 46 Hz
Amplitude: 0,2 / 0,55 mm
Vibration motor, VARIOMATIC:
Type: A4FM 28
System: Axial piston-swash plate
Displacement: 28 cm3
/U
Frequency: 46 Hz
Amplitude: 0,84 mm
Steering and charge pump:
Type: U 1636 11+8+2,5
System: Tandem-/Gear pump
Displacement: 11 / 8 / 2,5 cm3/U
Max. steering pressure: 200 +/-5 bar
Steering valve:
Type: OSPF 400 LS
System: Rotary valve
Swashing motor, VARIO:
Type: STF04-000-013
System: piston-gear rack
Filling capacities:
Engine oil: 13 l (SAE 15W-40, API CG-4 (for details see
maintenance manual))
Hydraulic oil: 60 l (HVLP 46 VI 150)
Vibration bearing housing: 7,5 l (SAE 15W-40, API SJ/CF)
Drum filling VARIO: 2 x 30 l (50% Water, 50% Anti -freeze agent on
Ethane-diol-basis)
AC refrigerant: 1100 g (R 134a)
Compressor oil (filling the system): 100 ml (PAG Öl)
Seite 2 von 2
BOMAG Central Service
22.06.2005
http://bsa.bomag.spx.com/bsa/tk_components/english/search_components_result.asp?...
14. Service Training
BW 141 - 154 AD/AC-4 - C 1 -
Maintenance
The products of series BW 141...154 AD/AC-4 are high performance machines for the extremely difficult
use in asphalt compaction and earth work. To be able to meet these demands the machines must
always be ready to be loaded up to their limits. Furthermore, all safety installations, protections and
guards must always be in place and fully functional.
Thorough maintenance of the machine is therefore mandatory. This not only guarantees a remarkably
higher functional safety, but also prolongs the lifetime of the machine and of important components.
The time required for thorough maintenance is only minor when being compared with the malfunctions
and faults that may occur if these instructions are not observed.
The maintenance intervals are given in operating hours. It is quite obvious that with each maintenance
interval all the work for shorter preceding intervals must also be performed. During the 2000 hours
interval you must also perform the work described for the service intervals after 50, 250 and 500 hours.
During maintenance work you must only use the fuels and lubricants mentioned in the table of fuels and
lubricants (oils, fuels, grease etc.).
This training manual is handed out together with the presently valid operation and maintenance manual.
For the individual maintenance intervals and the description of the maintenance work involved please
refer to these maintenance instructions.
15. Maintenance
BOMAG 63
BW 141 AD-4
5.3 Fuels, lubricants and filling
capacities
Assembly Fuel or lubricant Quantity approx.
Summer Winter Attention
Observe the level marks
Engine Engine oil
ACEA: E3-96/E5-02 13 litres without oil filter
API: CG-4/CH-4
SAE 10W/40 (-20 °C to +30 °C)
SAE 10W/40 (-10 °C to +40 °C)
SAE 30 SAE 10W
(+5 °C to +30 °C) (-5 °C to -30 °C)
SAE 40 SAE 20W/20
(+25 °C to +40 °C) (-10 °C to +10 °C)
Fuel
Diesel Winter diesel fuel (down
to -12 °C)
160 litres
Hydraulic system Hydraulic oil (ISO), HV46, kinem. viscosity
46 mm2/s at 40 °C or
ester based biodegradable hydraulic oil
60 litres
Sprinkler system Water Anti-freeze mixture and
water *
800 litres
Drum SAE 15W/40 5,3 litres (BW 141 AD-4)
- Exciter shaft tube 6,3 litres (BW 151 AD-4)
6,3 litres (BW 151 AC-4)
Travel gear, drum SAE 80W-90, API GL5 approx. 1.5 litres
Steering chains High pressure grease (lithium saponified) as required
Oscillating articulated joint High pressure grease (lithium saponified) as required
* Mix water and anti-freeze agent by following the instructions of the manufacturer
16. Maintenance
BOMAG
64 BW 141 AD-4
5.4 Running-in instructions
The following maintenance work must be per-
formed when running in new machines or
overhauled engines:
! Caution
Up to approx. 250 operating hours check the
engine oil level twice every day.
Depending on the load the engine is subjected
to, the oil consumption will drop to the normal
level after approx. 100 to 250 operating hours.
Maintenance after 50 operating hours
l Check the engine for leaks.
l Retighten bolted connections on intake and
exhaust tubes, oil sump and engine mounts.
l Retighten the bolted connections on the ma-
chine.
Maintenance after 250 operating hours
l 1st oil change in drum drive gear.
Maintenance after 500 operating hours
l 2nd oil change in drum drive gear.
Special intervals
l Switch the heating system*
on every month for
about 10 minutes.
l Switch the air conditioning* on every month for
about 10 minutes.
* Optional equipment
17. Maintenance
BOMAG 65
BW 141 AD-4
5.5 Maintenance chart
No. Maintenance work Remark
Running-in
instructions
after
250
operating
hours
every
10
operating
hours,
daily
every
250
operating
hours
every
500
operating
hours
every
1000
operating
hours
every
2000
operating
hours
every
3000
operating
hours
every
5000
operating
hours
as
required
5.6 Check the engine oil level Dipstick mark X
5.7 Check the water separator X
5.8 Check the fuel level X
5.9 Check the hydraulic oil level Inspection
glass
X
5.10 Check the water level X
5.11 Clean the cooling fins on engine
and hydraulic oil cooler
X
5.12 Check the oil level in vibrator shaft
tube
X
5.13 Change the engine oil*
min. 1x per year X
5.14 Change the engine oil filter car-
tridge**
min. 1x per year X
5.15 Servicing the air conditioning***
(summer operation)
X
5.16 Service the battery Pole grease X
5.17 Change the fuel filter cartridge X
5.18 Change the fuel pre-filter cartridge X
5.19 Change the oil in the drum drive
gear
X
5.20 Check, tension, lubricate the steer-
ing chain
X
5.21 Check the engine mounts X
5.22 Check, tension, replace the V-belt X
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Maintenance
BOMAG
66 BW 141 AD-4
5.23 Checking, tensioning, replacing
the refrigerant compressor V-belt
X
5.24 Changing the oil in the vibrator
shaft tube
X
5.25 Change hydraulic oil and breather
filter****
at least every 2
years
X
5.26 Change the hydraulic oil filter***** at least every 2
years
X
5.27 Grease the articulated joint******
at least every 2
years
X
5.28 Replace the injection valve X
5.29 Service the combustion air filter min. 1x per
year,
safety cartridge
at least every 2
years
X
5.30 Clean the water tank X
5.31 Clean the water filter X
5.32 Water sprinkler system, mainte-
nance in the event of frost
X
5.33 Fill the provision tank for the wind-
screen washer system
X
5.34 Adjusting the scrapers X
5.35 Tightening torques X
5.36 Engine conservation X
* Oil change intervals depend on quality of oil and fuel (sulphur content)
** Oil change intervals depend on quality of oil and fuel (sulphur content)
*** Optional equipment
**** Also in case of repair in the hydraulic system.
*****Also in case of repair in the hydraulic system.
******Also in case of repair in the hydraulic system.
No. Maintenance work Remark
Running-in
instructions
after
250
operating
hours
every
10
operating
hours,
daily
every
250
operating
hours
every
500
operating
hours
every
1000
operating
hours
every
2000
operating
hours
every
3000
operating
hours
every
5000
operating
hours
as
required
20. Service Training
BW 141 - 154 AD/AC-4 - D 1 -
Deutz diesel engine
Single drum rollers of series BW141/154 AD-4 are powered by a Deutz diesel engine of product range
BF4M 2011. In contrast to the engines 1011/1012 previously used by BOMAG, this engine comes with
external oil cooling, i.e. a separate oil cooler with a hydraulically driven fan, instead of the well known
integrated oil cooler/fan system.
This automotive engine is characterized by the following features:
• short and compact design,
• low noise level,
• low vibration running,
• low fuel consumption,
• low exhaust emissions,
• good access to all service points and
• extended maintenance intervals (5000 h) for toothed timing belt, in comparison to the predecessor
1011 F, by installation of an automatic tensioning device and improved enclosure of the belt drive.
The engine is a 4-cylinder 4-stroke inline engine with direct fuel injection.
The combustion method with direct fuel injection enables the use of a less expensive casting for the
cylinder head, highest possible utilization of fuel and minimum heat transfer to the coolant.
This in turn enables the use of a smaller and more compact radiator.
Both the crankcase with cylinders as well as the cylinder head of this ebngine are made of a cast iron
alloy. This provides strength and ensures high wear resistance.
The forged steel conrods are fitted with compensation weights near the conrod bearing seats. This
weight compensates manufacturing tolerances with respect to weight and centre of gravity.
The pistons are made of an aluminium alloy. The combustion trough has been specially designed for
efficient combustion. All pistons are fitted with three piston rings and are lubricated by an oil mist.
Each cylinder is fitted with one intake and one exhaust valve. The valve guides are shrunk into the
cylinder head.
21. Service Training
BW 141 - 154 AD/AC-4 - D 2 -
Control side
Fig. 1: Control side BFM 2011
1 Suction tube 2 without fan and fan bracket
3 V-belt pulley on crankshaft 4 Narrow V-belt
5 Fuel shut-off solenoid 6 Toothed belt cover
7 Shut-down lever 8 Control lever
9 Oil filler neck (on side of crankcase) 10 Oil dipstick
11 Fuel lift pump 12 Fuel filter
13 Port for oil heating 14 Lubrication oil filter
15 Injection pumps 16 Oil cooler port
17 Injection valves 18 Fuel return line