This document provides instructions for removing and installing an output transfer drive on a D400 articulated truck. The removal process involves draining fluids, disconnecting linkages and hoses, and using bolts and pins to separate the drive from the truck frame. Installation is the reverse of removal, and includes reconnecting fluids lines and adjusting linkages. Tolerances and torque specifications are provided for correctly installing components.
This document provides instructions for removing and installing an output transfer drive on a D400 articulated truck. The removal process involves draining fluids, disconnecting linkages and hoses, and using a hoist to remove the transmission/output transfer drive assembly. Installation is the reverse of removal, and includes adjusting alignments, connecting fluids and linkages, and refilling fluids. Disassembly of the inter-axle differential is also described.
Caterpillar cat d40 d articulated truck (prefix 8tf) service repair manual (8...fjsqazkekdmme
This document provides instructions for removing and installing the transmission hydraulic control valve on D40D and D400D articulated dump trucks. It describes removing the control valve from the transmission, then removing individual components like manifolds, sleeves, seals and spools. It then describes installing these components in reverse order, making sure surfaces are clean and sealed properly.
Caterpillar cat 313 f l excavator (prefix dje) service repair manual (dje0000...fjkskefksmeme
This document provides specifications and repair instructions for a 313F L excavator travel motor. It includes removal and disassembly procedures, specifications for individual parts, and assembly instructions. Key steps include draining oil, removing hoses and bolts to detach the motor, and using various tools to disassemble internal components like pistons, seals, and bearings. Reassembly follows the reverse of disassembly.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...yhhjjkfkseme
The document provides instructions for installing a hydraulic tank on a 303.5E Mini Hydraulic Excavator. The procedure involves 21 steps, including attaching lifting devices to the tank, installing it on the excavator, and reconnecting all hydraulic hoses and lines. Proper cleanliness and identification of all components is emphasized to prevent contamination of the hydraulic system.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdskekdmme
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, counterbalance valve, and other systems. The instructions are detailed, listing each part and step in the disassembly process. Required tools are provided at the beginning. Safety notices are included throughout to warn of hazards like stored energy in springs.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of an excavator model 313D2. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, piston assemblies, gears, seals and other parts. Tools required include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers and other specialized tools. Safety notices are provided to properly release pressures and contain fluids.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fjkskefksmeme
1) The document provides disassembly instructions for components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification numbers where applicable.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, seals and other parts while taking care to mark locations for reassembly.
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation. Lubrication and torque specifications are included for reassembly.
This document provides instructions for removing and installing an output transfer drive on a D400 articulated truck. The removal process involves draining fluids, disconnecting linkages and hoses, and using a hoist to remove the transmission/output transfer drive assembly. Installation is the reverse of removal, and includes adjusting alignments, connecting fluids and linkages, and refilling fluids. Disassembly of the inter-axle differential is also described.
Caterpillar cat d40 d articulated truck (prefix 8tf) service repair manual (8...fjsqazkekdmme
This document provides instructions for removing and installing the transmission hydraulic control valve on D40D and D400D articulated dump trucks. It describes removing the control valve from the transmission, then removing individual components like manifolds, sleeves, seals and spools. It then describes installing these components in reverse order, making sure surfaces are clean and sealed properly.
Caterpillar cat 313 f l excavator (prefix dje) service repair manual (dje0000...fjkskefksmeme
This document provides specifications and repair instructions for a 313F L excavator travel motor. It includes removal and disassembly procedures, specifications for individual parts, and assembly instructions. Key steps include draining oil, removing hoses and bolts to detach the motor, and using various tools to disassemble internal components like pistons, seals, and bearings. Reassembly follows the reverse of disassembly.
Caterpillar cat 303.5 e mini hydraulic excavator (prefix rky) service repair ...yhhjjkfkseme
The document provides instructions for installing a hydraulic tank on a 303.5E Mini Hydraulic Excavator. The procedure involves 21 steps, including attaching lifting devices to the tank, installing it on the excavator, and reconnecting all hydraulic hoses and lines. Proper cleanliness and identification of all components is emphasized to prevent contamination of the hydraulic system.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdskekdmme
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, counterbalance valve, and other systems. The instructions are detailed, listing each part and step in the disassembly process. Required tools are provided at the beginning. Safety notices are included throughout to warn of hazards like stored energy in springs.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of an excavator model 313D2. It lists over 30 detailed steps to disassemble components like the final drive housing, travel motor barrel assembly, piston assemblies, gears, seals and other parts. Tools required include link brackets, a transmission repair stand, bolts, pullers, retaining ring pliers and other specialized tools. Safety notices are provided to properly release pressures and contain fluids.
Caterpillar cat 313 f lgc excavator (prefix hdk) service repair manual (hdk00...fjkskefksmeme
1) The document provides disassembly instructions for components of a 313F LGC excavator, including the final drive, travel motor, and counterbalance valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification numbers where applicable.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, seals and other parts while taking care to mark locations for reassembly.
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation. Lubrication and torque specifications are included for reassembly.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. The 20 step process describes how to disassemble the motor into individual parts and then reassemble ensuring proper clearance and torque specifications are achieved.
Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service ...fujskefksmem
The document provides instructions for disassembling the track roller frame of a D8R track-type tractor. It describes removing components such as the track rollers, idlers, bogies, cartridge pins, and seals. Tools required are listed. Detailed steps and illustrations show how to support and lift heavy parts, drain oil, and use pullers and wedges to separate interconnected pieces in a specific sequence. Safety notices warn of risks such as heavy weight and contained fluids.
Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service ...udfujjsejkkem
The document provides instructions for disassembling the track roller frame of a D8R track-type tractor. It describes removing components such as the track rollers, idlers, bogies, cartridge pins, and seals. Tools required are listed. Detailed steps and illustrations show how to support and lift heavy parts, drain oil, and use pullers and wedges to separate interconnected pieces in a specific sequence. Safety notices warn of risks such as heavy weight and contained fluids.
Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service ...kfdjkskdmm
The document provides instructions for disassembling the track roller frame of a D8R track-type tractor. It describes removing components such as the track rollers, idlers, bogies, cartridge pins, retainers, seals and bearings. Tools required are listed. Detailed step-by-step instructions and illustrations are provided to remove each component safely, including the use of lifting devices, wedges, pullers and other tools due to the heavy weight of parts. Personal safety warnings are also given throughout due to risk of injury.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...zatao0179249295
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper tooling is required and parts must be cleaned, marked and replaced in their original locations and orientations. Safety notices warn of spring forces, contained fluids, and preventing contamination.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...yinranhe0814
The document provides step-by-step instructions for disassembling and assembling a travel motor. It details removing components like the head, plates, seals, and piston assemblies. Cleaning and inspection of parts is emphasized. The assembly section outlines installing seals, spacers, and other components in reverse order of disassembly. Proper component orientation and cleanliness during assembly are stressed.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...wfu089267
The document provides step-by-step instructions for disassembling and assembling a travel motor. It details removing components like the head, plates, seals, and piston assemblies. Cleaning and inspection of parts is emphasized. The assembly section outlines installing seals, spacers, and other components in reverse order of disassembly. Proper component orientation and cleanliness during assembly are stressed.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves removing 27 different components from the travel motor body in a specific sequence. The assembly process reverses the disassembly steps and provides additional details like applying lubricants and installing components in their original positions and orientations. Proper assembly requires using the correct tools and following all notes, illustrations, and installation procedures carefully to prevent damage.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjjskmdmem
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor into components like the brake assembly, piston assemblies, and head assembly. The reassembly process is described by cleaning parts and reinstalling components in reverse order using threadlock and ensuring proper orientation of seals and shims.
Caterpillar cat 350 l track type excavator (prefix 9dk) service repair manual...fjsjjekdkme
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor into components like the brake assembly, piston assemblies, and head assembly. The reassembly process is described by cleaning parts and reinstalling components in reverse order using thread lock and new seals as needed.
Caterpillar cat 350 l track type excavator (prefix 9dk) service repair manual...fjjskmdmem
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor by removing components like the brake cover, springs, piston, and housing parts. The assembly process is described by cleaning parts, checking seals, and reversing the disassembly steps while taking care to reinstall components in their original positions and orientations.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjsjjekdkme
This document provides instructions for removing and installing travel motors on 350 and 350L excavator models. It describes:
1) Removing the travel motor by disconnecting hoses, removing bolts, and lifting it out using threaded rods and a hoist.
2) Disassembling the travel motor by removing covers, springs, discs, seals, and housing components.
3) Assembling the travel motor by cleaning parts, checking seals, and reversing the removal steps.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjsjjekdkme
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor into components like the brake assembly, piston assemblies, and head assembly. The reassembly process is described by cleaning parts and reinstalling components in reverse order using threadlock and ensuring proper orientation of seals and shims.
Caterpillar cat 350 l track type excavator (prefix 9dk) service repair manual...fjsjjekdkme
This document provides instructions for removing and installing travel motors on 350 and 350L excavator models. It describes:
1) Removing the travel motor by disconnecting hoses, removing bolts, and lifting it out using threaded rods and a hoist.
2) Disassembling the travel motor by removing covers, springs, discs, seals, and housing components.
3) Assembling the travel motor by cleaning parts, checking seals, and reversing the removal steps.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...wedsrffcdgdv
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. It describes using a special tool to press the seal out of and into the front cover. Cleanliness is emphasized to prevent premature wear. The instructions are part of a service manual for Caterpillar C7.1 engines.
Caterpillar cat 950 k wheel loader (prefix fer) service repair manual (fer000...wedsrffcdgdv
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 950K wheel loader. It describes 28 steps to disassemble the steering pump, including removing valves, spools, springs, and other internal components. It then lists 34 steps for reassembling the steering pump. The summary advises checking axial shaft end play during installation and adjusting as needed with a shim.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. It begins by listing the required tools. It then provides step-by-step instructions to disassemble the various components of the pump, including removing seals, springs, valves, and housing pieces. Detailed illustrations accompany each step. Safety notices are included to warn of potential injuries from released springs or pressurized components. The disassembly process yields all individual parts of the pump.
More Related Content
Similar to Caterpillar cat d400 articulated truck (prefix 1 md) service repair manual (1md00001 00246)
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. The 20 step process describes how to disassemble the motor into individual parts and then reassemble ensuring proper clearance and torque specifications are achieved.
Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service ...fujskefksmem
The document provides instructions for disassembling the track roller frame of a D8R track-type tractor. It describes removing components such as the track rollers, idlers, bogies, cartridge pins, and seals. Tools required are listed. Detailed steps and illustrations show how to support and lift heavy parts, drain oil, and use pullers and wedges to separate interconnected pieces in a specific sequence. Safety notices warn of risks such as heavy weight and contained fluids.
Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service ...udfujjsejkkem
The document provides instructions for disassembling the track roller frame of a D8R track-type tractor. It describes removing components such as the track rollers, idlers, bogies, cartridge pins, and seals. Tools required are listed. Detailed steps and illustrations show how to support and lift heavy parts, drain oil, and use pullers and wedges to separate interconnected pieces in a specific sequence. Safety notices warn of risks such as heavy weight and contained fluids.
Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service ...kfdjkskdmm
The document provides instructions for disassembling the track roller frame of a D8R track-type tractor. It describes removing components such as the track rollers, idlers, bogies, cartridge pins, retainers, seals and bearings. Tools required are listed. Detailed step-by-step instructions and illustrations are provided to remove each component safely, including the use of lifting devices, wedges, pullers and other tools due to the heavy weight of parts. Personal safety warnings are also given throughout due to risk of injury.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...zatao0179249295
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper tooling is required and parts must be cleaned, marked and replaced in their original locations and orientations. Safety notices warn of spring forces, contained fluids, and preventing contamination.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...yinranhe0814
The document provides step-by-step instructions for disassembling and assembling a travel motor. It details removing components like the head, plates, seals, and piston assemblies. Cleaning and inspection of parts is emphasized. The assembly section outlines installing seals, spacers, and other components in reverse order of disassembly. Proper component orientation and cleanliness during assembly are stressed.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...wfu089267
The document provides step-by-step instructions for disassembling and assembling a travel motor. It details removing components like the head, plates, seals, and piston assemblies. Cleaning and inspection of parts is emphasized. The assembly section outlines installing seals, spacers, and other components in reverse order of disassembly. Proper component orientation and cleanliness during assembly are stressed.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves removing 27 different components from the travel motor body in a specific sequence. The assembly process reverses the disassembly steps and provides additional details like applying lubricants and installing components in their original positions and orientations. Proper assembly requires using the correct tools and following all notes, illustrations, and installation procedures carefully to prevent damage.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjjskmdmem
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor into components like the brake assembly, piston assemblies, and head assembly. The reassembly process is described by cleaning parts and reinstalling components in reverse order using threadlock and ensuring proper orientation of seals and shims.
Caterpillar cat 350 l track type excavator (prefix 9dk) service repair manual...fjsjjekdkme
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor into components like the brake assembly, piston assemblies, and head assembly. The reassembly process is described by cleaning parts and reinstalling components in reverse order using thread lock and new seals as needed.
Caterpillar cat 350 l track type excavator (prefix 9dk) service repair manual...fjjskmdmem
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor by removing components like the brake cover, springs, piston, and housing parts. The assembly process is described by cleaning parts, checking seals, and reversing the disassembly steps while taking care to reinstall components in their original positions and orientations.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjsjjekdkme
This document provides instructions for removing and installing travel motors on 350 and 350L excavator models. It describes:
1) Removing the travel motor by disconnecting hoses, removing bolts, and lifting it out using threaded rods and a hoist.
2) Disassembling the travel motor by removing covers, springs, discs, seals, and housing components.
3) Assembling the travel motor by cleaning parts, checking seals, and reversing the removal steps.
Caterpillar cat 350 track type excavator (prefix 9 dk) service repair manual ...fjsjjekdkme
This document provides instructions for removing, disassembling, and assembling the travel motors on 350 and 350L excavator models. It describes removing the travel motor by disconnecting hoses, removing bolts, and lifting it out. It then details disassembling the motor into components like the brake assembly, piston assemblies, and head assembly. The reassembly process is described by cleaning parts and reinstalling components in reverse order using threadlock and ensuring proper orientation of seals and shims.
Caterpillar cat 350 l track type excavator (prefix 9dk) service repair manual...fjsjjekdkme
This document provides instructions for removing and installing travel motors on 350 and 350L excavator models. It describes:
1) Removing the travel motor by disconnecting hoses, removing bolts, and lifting it out using threaded rods and a hoist.
2) Disassembling the travel motor by removing covers, springs, discs, seals, and housing components.
3) Assembling the travel motor by cleaning parts, checking seals, and reversing the removal steps.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly process reverses the disassembly with 23 steps like installing seals, springs, piston assemblies and keys in their proper positions and orientations. Special tools and precautions are noted to prevent damage and ensure correct assembly.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Similar to Caterpillar cat d400 articulated truck (prefix 1 md) service repair manual (1md00001 00246) (19)
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...wedsrffcdgdv
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 950K wheel loader. It describes using a special tool to press the seal out of and into the front cover. Cleanliness is emphasized to prevent premature wear. The instructions are part of a service manual for Caterpillar C7.1 engines.
Caterpillar cat 950 k wheel loader (prefix fer) service repair manual (fer000...wedsrffcdgdv
The document provides instructions for removing and installing a secondary steering pump and electric motor on a Caterpillar 950K wheel loader. It describes 28 steps to disassemble the steering pump, including removing valves, spools, springs, and other internal components. It then lists 34 steps for reassembling the steering pump. The summary advises checking axial shaft end play during installation and adjusting as needed with a shim.
This document provides instructions for disassembling a piston pump used in Caterpillar articulated trucks. It begins by listing the required tools. It then provides step-by-step instructions to disassemble the various components of the pump, including removing seals, springs, valves, and housing pieces. Detailed illustrations accompany each step. Safety notices are included to warn of potential injuries from released springs or pressurized components. The disassembly process yields all individual parts of the pump.
This document provides instructions for removing and installing a piston pump and pump control valve on a 725 Articulated Truck. It outlines 37 steps to disassemble the piston pump, checking components for wear, lubricating seals, and precisely adjusting preload on bearings. It then describes 4 steps to install the piston pump and connect hoses. Finally, it warns of hot oil and pressures in the hydraulic system and lists 1 step to remove identification marks from hoses when removing the pump control valve.
Caterpillar cat 336 f l excavator (prefix yfd) service repair manual (yfd0000...wedsrffcdgdv
This document provides instructions to disassemble a 336F excavator travel motor. It outlines 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, retaining ring pliers and other specialized tools. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f l excavator (prefix nbl) service repair manual (nbl0000...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Caterpillar cat 336 f l excavator (prefix lcl) service repair manual (lcl0000...wedsrffcdgdv
This document provides disassembly instructions for a travel motor on a 336F excavator model. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, swashplate, and other internal components. Various tools are required to remove retaining rings, seals, springs, and other parts in the proper sequence. Care must be taken to mark components' locations and ensure springs and other parts are released safely.
Caterpillar cat 336 f l excavator (prefix dsw) service repair manual (dsw0000...wedsrffcdgdv
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety notices advise wearing protective equipment when compressing springs or releasing pressurized components during disassembly.
Caterpillar cat 336 f excavator (prefix yfd) service repair manual (yfd00001 ...wedsrffcdgdv
This document provides instructions to disassemble a 336F excavator travel motor. It lists 27 steps to fully disassemble the travel motor, including removing components like the head, springs, pistons, plates, seals and more. Tools required include bolts, pins, drivers, pullers and stands to safely remove parts and release spring forces. Detailed illustrations accompany each step to show how to disassemble the various systems and components of the travel motor.
Caterpillar cat 336 f excavator (prefix nbl) service repair manual (nbl00001 ...wedsrffcdgdv
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety warnings are provided throughout for components under spring pressure.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...wedsrffcdgdv
This document provides instructions for disassembling the travel motor on a 336F and 336F L excavator. The 27-step process includes removing components like the motor head assembly, piston assemblies, barrel assembly, swashplate, and seals. Special tools are required to remove parts and release spring forces safely. The detailed illustrations and part numbers allow technicians to accurately disassemble and reassemble the travel motor.
Bomag bw 177 single drum rollers service repair manualwedsrffcdgdv
The document provides a maintenance table for a single drum roller that outlines maintenance work to be performed at various operating hour intervals. It lists over 40 maintenance items ranging from daily checks of fluid levels to annual tasks like changing engine oil and filters. Performing regular maintenance according to the schedule is important to ensure the machine is ready for demanding construction work and all safety systems function properly.
Clark esm 12 25 forklift service repair manualwedsrffcdgdv
This document provides maintenance instructions for an electric lift truck. It outlines a planned maintenance program with periodic inspections and maintenance tasks to complete. The inspections and tasks are divided into groups to make the maintenance efficient. Safety practices for maintenance are also described. Completing regular planned maintenance is important for the safe operation and long life of the lift truck.
Clark cq202530 l forklift service repair manualwedsrffcdgdv
The document provides information on servicing and maintaining the CQ20-30 truck transaxle:
- The transaxle construction includes a torque converter, single-speed transmission, differential, drive axle, and drum brakes. Maintenance includes checking fluid levels, changing fluid and filters regularly, and adjusting the service brakes.
- Precautions for disassembly and assembly emphasize cleanliness to prevent contamination. The transaxle has openings for checking fluid levels and draining fluid. Filters should be replaced every 1,000 hours.
- Brake adjustments can be made through openings in the backing plate or wheel hub, aiming for a brake shoe to drum clearance of 0.255-0.304
Clark cq202530 d forklift service repair manualwedsrffcdgdv
The document provides information on servicing the CQ20-30 transaxle:
- It describes the construction of the TA18 transaxle assembly and its components.
- Maintenance procedures are outlined, including checking fluid level and changing fluid and filter every 1,000 hours.
- Pressure specifications and check points for the regulator valve, converter, clutches, and other components are provided.
- The process for adjusting the service brakes via the backing plate or wheel hub opening is described in detail. Cleanliness and proper adjustment are emphasized to prevent issues.
Clark cmp 70 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark cmp 60 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Clark cmp 50 forklift service repair manualwedsrffcdgdv
This document provides safety instructions for lifting, jacking, and blocking a CLARK forklift truck during maintenance. It identifies approved lifting points on the truck and describes procedures for safely raising different parts of the truck, including the drive wheels, front with a hoist, and upright carriage. Workers are instructed to use blocking and wheel cradles, and cautioned to ensure any lifting equipment is rated for the truck's weight.
Caterpillar cat d550 b articulated dump truck (prefix 5nd) service repair man...wedsrffcdgdv
This document provides instructions for servicing various components of a Caterpillar 3408 engine, including removing and installing the camshaft, camshaft bearings, timing gears, flywheel, and flywheel housing. The camshaft removal procedure involves using several tools to remove the camshaft gear, camshaft, and dowel. Camshaft bearing removal requires using a tool from the rear of the cylinder block. Timing gear removal involves removing the front balance gear and crankshaft gear. Flywheel removal requires fastening a tool and lifting the flywheel off. Flywheel housing removal requires removing mounting bolts and a bracket.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...wedsrffcdgdv
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a D400E II Ejector Truck with a 3406E engine. The procedures describe draining fluids, using various specialty tools to compress springs, extract components, and properly position replacement parts. Safety precautions are provided to prevent injury when handling springs or draining fluids.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: D400 ARTICULATED TRUCK 1MD
Configuration: D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1MD00001-00246 (MACHINE) POWERED BY 3406B ENGINE
Disassembly and Assembly
ARTICULATED DUMP TRUCK OUTPUT TRANSFER DRIVE
Media Number -SENR8109-01 Publication Date -01/01/1986 Date Updated -12/10/2001
Output Transfer Drive
SMCS - 1453-016
Remove Output Transfer Drive
Tools Required:
NOTE: The following photographs show the removal/installation procedure for a typical output transfer drive
assembly. The procedure is similar for 'C' trucks and the D400 - where there are differences, these are noted and
specific instructions are given.
1. Stop the truck in the straight ahead position and apply the parking brake. Move the gear lever to the Neutral
position and stop the engine. Remove the key and place suitable warning notices to prevent personnel starting the
engine and operating the controls. Use the hand lever on the suspension control valve to fully lower the front
suspension.
2. With the oil warm, remove the drain plug (1) and allow the oil to drain into a suitable container (C Truck - 35
litres) (D400 - 105 litres).
3. Remove the transmission compartment grille (2).
1/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 4. Release the retaining clips (3) from the access door struts (4).
5. Remove the rear access door assembly (5).
6. Disconnect and remove the hoist control linkage and rod assembly.
7. C-trucks: Remove the cam housing cover (6). Disconnect and remove the selector cable (7) from the housing.
Refit the cover (6) to prevent dirt entering the housing.
8. D400: Disconnect the torque converter lock up oil line (8) from the transfer gearbox.
2/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 9. D400: Disconnect the transmission control cables (9) from the rear of the transmission control group housing.
10. Trucks fitted with supplementary steering: Remove the supplementary steer hoses (10 and 11) from the diverter
valve (12) to the pipes (13) and (14). Plug the ports on the diverter valve and cap the hoses to prevent
contamination.
11. Trucks fitted with supplementary steering: Remove both pipe assemblies (13) and (14) from the supplementary
steer pump.
12. Trucks fitted supplementary steering: Remove the supplementary steer pump (15).
13. Remove the bolts that secure the transmission drive shaft (16). Remove the drive shaft. D400 (early trucks) -
Disconnect the wires (17) from the magnetic pick-up. Mark the wires to ensure correct reconnection.
14. Remove the bolts that secure the spider (18). Remove the spider.
3/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 15. Remove the cotter pin (19) and the clevis pin (20) from the differential lock actuator.
16. Remove the bolts securing the output transfer drive rear output yoke to the centre drive shaft (21). Slide the
centre drive shaft backward.
17. D400 - Remove the bolts securing the torque converter valve group (22) to the transmission mounting bracket.
Disconnect the valve group oil supply line (24). Move the valve group to allow clearance when the transmission and
output transfer drive assembly is hoisted out of the compartment. Remove the oil filler tube assembly (25).
Disconnect the remaining oil lines (26) and (27) from the front of the transmission. Disconnect the oil cooler return
line (23).
18. C Trucks - Disconnect the oil lines (28-34) from the front of the transmission. Mark the oil lines to ensure
correct reconnection. Plug the ports and cap the hoses to reduce oil spillage and prevent contamination.
19. All trucks - Disconnect the sump line connection (35) from the output transfer drive housing.
4/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 20. D400 - Disconnect the torque converter drain line (36) from the output transfer drive housing.
21. Remove the upper bolts (37) securing the left and right hand mounting brackets (38).
NOTE: On current trucks it is not necessary to remove the left and right hand mounting brackets.
22. Remove the bolts securing the upper transmission mounting assembly (39). Remove the mounting assembly.
Remove the torque converter selector valve (40) to provide more clearance.
NOTE: Place a wooden plank or similar form of protection at the rear of the transmission compartment. This will
prevent damage to any components when the upper transmission mounting assembly is removed and the
transmission/output transfer drive assembly pivots backwards.
23. Place a suitable hoisting sling around the assembly as shown and connect the sling to a hoist.
5/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 24. Early trucks: If necessary, disconnect the steering line pipe connections (41), also ...
It is important that the complete assembly is securely supported by the
hoist and sling during the following procedure. This will prevent the
assembly from moving downward when finally released from the truck
frame, thus avoiding the possibility of injury or damage.
25. Early trucks: ... slacken the mounting brackets for both pipes (42) to allow sufficient movement of the pipes to
provide clearance for the output transfer drive assembly during the hoisting procedure.
26. Drill out the indented lip of the locating ring (43) and remove the locating ring using tool 6V3133 Spanner
Wrench. Remove the bolts (44) from the left and right hand pivot pins. Remove the pivot pins (45).
27. Remove the remaining lower bolts (46) from the left and right hand mounting brackets. Remove both mounting
brackets (38).
6/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 28. Hoist the complete transmission/output transfer drive assembly out of the truck.
29. Lower the assembly on to suitable stands, disconnect the hoist and remove the sling.
30. Attach a sling and hoist to the transmission. Install two 3/8 - 16NC forcing bolts (47) to separate the
transmission from the output transfer drive. Remove the transmission from the output transfer drive. The weight of
the transmission is 622 kg (1370 lb.).
31. End by:
(a) Disassemble output transfer drive.
(b) Disassemble transmission - see CAT Form Number SENR 2393 '615 Tractor-Scraper Power Train-Disassembly
and Assembly' which can be found in CAT Service Manual SENR 2386 '615 Tractor-Scraper'.
Install Output Transfer Drive
New Parts Required:
7/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Tools Required:
1. Start by:
(a) Assemble output transfer drive
(b) Assemble transmission - see CAT Form Number SENR 2393 '615 Tractor-Scraper Power Train-Disassembly
and Assembly' which can be found in CAT Service Manual SENR 2386 '615 Tractor-Scraper.'
(c) Assemble transmission to output transfer drive using 3S9896 or 5P2587 seal as appropriate.
2. Attach a sling and connect to a hoist. Lower the assembly into position in the transmission compartment. Take
care when lowering past the steering system pipes. The two pipes, slackened previously in "Remove Output
Transfer Drive" procedure - steps 24 and 25, can be moved to provide the clearance necessary to position the
assembly in the compartment.
It is important that the complete assembly is securely supported by the
hoist and sling during this procedure.
8/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 3. Position the left and right hand mounting brackets (1) against the output transfer drive. Install the lower bolts and
washers (2) initially and fully tighten to a torque setting of 360±47 Nm (265±35 lb.ft.).
NOTE: On current trucks the transmission and output transfer drive assembly can be installed with the left and right
hand mounting brackets in position.
4. Position the assembly so that the pivot pins (3) can be installed through the right and left hand mounting brackets
(1). Install the pivot pins. Be sure the slot in each pin is facing towards the front of the truck.
5. Install the bolts (4) and washers and tighten to a torque setting of 360±47 Nm (265±35 lb.ft.).
6. Install the locating ring (5). Use tool 6V3133 Spanner Wrench to tighten the locating ring until it just touches the
face of the mounting bracket (1). Measure the gap (6) on each side of the truck and adjust the locating rings until
both dimensions are equal to within 2mm.
7. Lock the locating ring (5) in position by using a punch to indent the ring lip into the slot in each pivot pin (3).
9/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) 1...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 8. Check the alignment of the transmission to the front axle. The centre lines of the transfer drive output shaft and
the front differential input shaft must be within 1.5mm (0.06 inch) measured sideways. Measure by placing a
straight edge across the machined surfaces of the respective yokes.
Shims (7) are installed between the bearing cap (8) and the front suspension frame (9). If adjustment is necessary
remove shims from under one bearing cap and install the same shims under the bearing cap on the other side. Before
carrying out adjustment slacken clamp bolts (10). Tighten fully after adjustment.
9. Install upper bolts (2) and washers to the left and right hand mounting brackets (1). Fully tighten to a torque
setting of 360±47 Nm (265±35 lb.ft.).
10. Early trucks: Connect steering pipes (11).
11. Early trucks: Connect brackets (12) to the truck frame.
10/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 12. Install a wooden plank behind the transmission then remove the hoist and sling.
13. Install the upper transmission mounting bracket assembly (13).
14. 'C' Trucks & D400: Connect the sump line (14) to the front of the output transfer drive housing using a new seal.
15. D400: Connect the torque converter drain line (15) to the front of the output transfer drive housing.
16. C Truck - Connect the oil lines (16-22) to the transmission housing using new seals.
11/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 17. D400 - Install the torque converter valve group (23) to the transmission mounting bracket (24). Connect the
valve group oil supply line (26). Install the oil filler tube assembly (28) using a new gasket. Install the remaining oil
lines (25 and 27) to the front of the transmission and the oil cooler return line (29) using new seals.
18. Slide the centre drive shaft (30) forward and connect it to the output yoke. Tighten the bolts to a torque setting of
135±14 Nm (100±10 lb.ft.).
19. Position the differential lock actuator shaft on the differential selector shaft and install clevis pin (31). Insert a
new cotter pin (32) making sure that sufficient washers are installed under the cotter pin to take up all free play on
the clevis pin.
20. Install the spider (33) connecting the front drive axle to the output transfer drive.
21. Install the transmission drive shaft (34). C Trucks:
The transmission drive shaft should have between 4 and 10mm sliding allowance between the male and female
parts. Measure the distance between the machined faces of the two spider and bearing assemblies with the shaft
fully compressed. Install the drive shaft then adjust the top transmission mounting until the distance between the
same two faces is 4-10mm greater than the fully compressed dimension.
12/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. D400:
A clearance of 5-6mm should exist between the rear face of the input yoke and the face of the cage of the
transmission input transfer gear. The clearance is obtained by adjusting the top transmission mounting. The above
clearance is for a truck on wheels. If supported on stands the clearance should be 3-4mm.
Note for all trucks:
The method of adjusting the top transmission mounting depends on the arrangement fitted. On early trucks
adjustment is achieved by fitting washers under the head of the bolt which passes through the mounting. On later
trucks adjust the number of shims between the mounting block and the truck frame.
22. C trucks - Install the selector cable (35) to the cam housing (36). Install the cover (37) with a new gasket if
necessary. Refer to "Transmission Control Linkage Adjustment - C Trucks" if adjustment is required.
23. D400 - Install the transmission control cables (38) to the rear of the transmission control group housing. Refer to
"Transmission Control Linkage Adjustments - D400" if adjustment required.
13/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 24. Connect the hoist control linkage and rod assembly.
25. Trucks equipped with supplemental steering: Install the supplemental steer pump (39) using a new gasket.
Tighten the nuts to a torque setting of 100±14 Nm (75±10 lb.ft.).
26. Trucks equipped with supplemental steering: Install the two pipe assemblies (40 and 41) to the supplemental
steer pump. Install the two hose assemblies (42) to the pipe assemblies (40 and 41) and to the connections at the
diverter valve (43). Tighten all bolts to a torque setting of 100±14 Nm (75±10 lb.ft.) except the bolts into the
diverter valve which are tightened to 80±4 Nm (60±3 lb.ft.). Use new seals
27. D400: Install the torque converter lock up oil line (44) to the output transfer drive.
28. Install the rear access doors assembly.
14/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 29. Install the retaining clips (45) to the access door struts.
30. Early trucks: Install the transmission compartment rear grille (46).
31. End by:
a) Fill transmission with oil.
b) Top up hydraulic tank.
Disassemble Inter Axle Differential
Start by:
a) Remove inter-axle differential.
1. Remove bearing cone (1).
2. Remove the screws (12 off) securing the drive dog (2) to the housing.
15/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 3. Remove the bearing cone (3).
4. Remove the locking wire from all bolts (8 off) securing gear (4) to the housing assembly. Remove all bolts (5).
5. Install two 1/2" UNC forcing bolts to separate gear (4) from the housing. Remove the gear. Mark the gear and
housing to ensure correct alignment upon reassembly.
6. Remove the bolts (6).
7. Separate the housing assembly ...
16/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. ... to reveal the gearing arrangement.
9. Remove the thrust washers (7) - 8 off.
10. Remove the gears (8) - 8 off.
11. Remove the thrust washers (9) - 8 off.
12. Remove the thrust washer (10).
17/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 13. Remove gear (11).
14. Remove gear (12).
15. Remove thrust washer (13).
16. Remove all pins (14) - 4 long and 4 short. Note the location of both types of pins to ensure correct reassembly.
Inspect/Replace Worn Parts
1. Clean and inspect the long (1) and short (2) pins for excess wear or scoring. Replace if excessively worn.
18/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 2. Clean and inspect the input gear (3) for burrs, excessive or incorrect wear or other damage. Stone away any burrs
and replace if damaged.
3. Inspect the small gears (4) for wear and the plain bearings within each gear for wear or scoring.
4. Inspect all thrust washers (5) for excessive wear and replace as necessary.
Assemble Inter Axle Differential
New Parts Required
1. Install all pins - 4 long (1) and 4 short (2) into the housing as shown.
19/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. 8. Install eight thrust washers (9).
9. The lower housing assembly is shown complete and ready for further assembly.
10. Install housing (10) on to the completed lower housing assembly (11) using roll pin (12) to ensure correct
assembly.
11. Install four bolts (13) and tighten evenly to a torque setting of 102 ± 15 Nm (75 ± 10 lb.ft.).
12. Use a suitable solvent to thoroughly clean and degrease the mating surfaces of the gear (14) and the housing and
the tapped holes in the housing. Apply a coating of 2U2856 retaining compound to the mating surfaces. Install gear
(14). Position the gear so that the four long pins locate into the four recessed holes in the mating surface of the gear.
21/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 13. Install bolts (15) - 8 off. Tighten evenly to a torque setting of 129±15 Nm (95±10 lb.ft.). Wire lock all bolts
using 5P6027 locking wire.
14. Install bearing cone (16).
5. Use a suitable solvent to thoroughly clean and degrease the mating surfaces of drive dog (17) and the housing.
Smear the mating surfaces with 2U2856 retaining compound and install the drive dog (17). Apply a coating of
2U2855 thread lock to the screw threads after suitably degreasing. Tighten the screws to a torque setting of 122±15
Nm (90 ± 10 lb.ft.).
16. Install bearing cone (18).
Disassemble Output Transfer Drive
22/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 1. Start by:
a) Remove inter axle differential.
2. Remove the differential guard (1) from the output transfer drive housing. The guard is secured by three bolts.
3. Attach bracket (2) to the output transfer drive housing cover (3). Attach a hoist to the bracket and lower onto a
prepared surface before further disassembly is started.
NOTE:
a) The bracket is to be found in the tool box located in the operator's compartment.
b) The dipstick tube assembly has already been removed in the illustration.
4. Remove all bolts (18 off) securing the housing cover (3). Install two 3/8" UNF eyebolts and attach a hoist.
23/48
D400 ARTICULATED TRUCK(SEE MACHINE AR FOR SERIAL NO. CHART) ...
2020/2/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...