5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Isn't Your BMW X5's Comfort Access Functioning Properly Find Out Here
Caterpillar Cat 350 Excavator (Prefix 3ML) Service Repair Manual (3ML00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A EXCAVATOR 3ML
Configuration: 350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 6 g00453011
6. Remove shaft assembly (15) and levers (14) and (13) .
Illustration 7 g00453012
7. Remove two snap rings (19) from two pins (17). Remove two pins (17). Remove plates (16)
and stop (18) .
Illustration 8 g00453014
8. Remove pins (21) and (22) and remove spring (20) .
4/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 9 g00453015
9. Remove two bolts (23), and the washers, and remove adapter (24), the coupling, and the O-
ring seal.
10. Remove contact (27) and body (28) with an O-ring seal.
11. Remove two bolts (29) and the washers and remove cover (30) and the gasket.
12. Remove two nuts and washers (26) and remove shutoff solenoid (25) and the gasket.
Illustration 10 g00453016
13. Remove shaft (31) and lever (32) .
5/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g00453017
Note: The check valve will be damaged during removal. Remove check valve (33) only if a
replacement is necessary.
14. Remove check valve (33) only if a replacement is necessary.
Illustration 12 g00453018
15. Remove seal (34) and adjustment screw (35) .
6/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g00453019
16. Remove bolt (36), housing (37) and the gasket from the fuel injection pump housing.
Illustration 14 g00453557
Typical example
17. Remove bolts (38) and remove torque control (39) .
18. Disassemble torque control (39) and inspect the spacer, the spring, and the insulator for
damage or wear. Replace parts that are worn or damaged with new parts.
Illustration 15 g00453558
19. Remove two bolts (40) and block (41) .
7/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 16 g00453559
20. Remove the bolt that holds collar (42) to bolt (44). Remove collar (42), spring (43) and bolt
(44) .
21. Remove the stop screws from collar (42) if the collar needs to be replaced.
Illustration 17 g00453560
22. Remove three bolts (46) and remove governor servo (45). The governor servo must be
rotated in order to be released from the rack's regulator.
8/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g00453632
23. Remove lockring (50), seat (53), link spring (52) and sleeve (51). Remove the other
lockring (50) from the groove in the center of valve (47). Remove valve (47), sleeve (48)
and piston (49). The piston must be pushed down in order to be removed. Remove the O-
ring seal from sleeve (48). Remove pin (55) and lever (56) .
Illustration 19 g00453633
Illustration 20 g00453634
24. Use Tool (A) in order to hold spring (58) compressed for the removal of ring (57). Spring
(58) is used in order to put a preload on the thrust bearing for the camshaft in the fuel
injection pump housing.
25. Remove ring (57) and slowly release Tool (A) .
9/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g00453635
26. Remove bearing (60), sleeves (59) and spring (58) .
Illustration 22 g00453636
27. Remove ring (61) and dashpot assembly (62) .
Illustration 23 g00453637
28. Use Tool (C) in order to remove snap ring (68). Remove ring (67) and spool (66) .
10/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 29. Remove seat (65) from spring (64) and remove spring (64) from seat (63) .
Illustration 24 g00453665
30. Remove riser (69) .
Illustration 25 g00453667
31. Remove ring (70), races (71) and bearing (72) .
11/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 26 g00453668
32. Remove four bolts (73) and carrier (74) .
Illustration 27 g00453669
33. Remove dowels (77) and flyweights (76). Remove governor shaft (75) and the dowel that is
not shown from shaft (75) .
Illustration 28 g00453670
34. Remove races (78) and bearing (79) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 23 09:32:29 UTC+0800 2021
12/12
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A EXCAVATOR 3ML
Configuration: 350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111261
Governor - Assemble
SMCS - 1264-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
B 6V-2163 Spring Clamp 1
C 1P-0510 Driver Group 1
D 6V-2054 Shield Driver 1
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets, the seals, or any
parts are worn or damaged, use new parts for replacement.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00453799
1. Install one race (1), bearing (2) and the other race (1) on the camshaft in the fuel injection
pump housing.
Illustration 2 g00453801
2. Put flyweights (4) in position on carrier (3) and install the dowels in order to hold the
flyweights in place. The flyweights must move freely on the dowels.
Illustration 3 g00453802
2/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Install dowel (5) in governor shaft (6) and install the governor shaft in the carrier (3) .
Illustration 4 g00459340
4. Put carrier (3) in position and install bolts (7) .
Illustration 5 g00459410
5. Install race (9), bearing (10) and race (9). Use Tool (A) in order to install ring (8) on riser
(11) .
3/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g00459411
6. Install riser (11) .
Illustration 7 g00459414
7. Assemble the dashpot, as follows:
a. Install spring (13) on seat (12) and install seat (14) in spring (13) .
b. Put spool (15) and ring (16) in position on seat (14) and use Tool (A) in order to
install snap ring (17) .
4/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 8 g00459416
8. Install dashpot assembly (19). Install ring (18) in the lower groove in the governor shaft.
Illustration 9 g00459419
9. Install sleeve (20), spring (22), sleeve (20) and bearing (21) .
Note: Spring (22) is used in order to put a preload on the thrust bearing on the camshaft in
the fuel injection pump housing.
5/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00459421
10. Use Tool (B) in order to hold spring (22) compressed and install ring (23) in the groove in
the governor shaft. Remove Tool (B) .
Illustration 11 g00459423
11. Put lever (33) in position on the governor servo and install pin (32) in order to hold the lever
in place. Use a hammer and a chisel in order to move the metal (stake) at four places that are
spread apart 90 degrees. Perform this procedure on the outside surface on both legs of the
governor servo. This helps to hold pin (32) in place.
12. Install the O-ring seal on sleeve (25). Install piston (26) and sleeve (25) .
13. Install valve (24) .
14. Install one lockring (27) in the groove near the center of valve (24). Put sleeve (28), link
spring (29) and seat (30) in position on valve (24) and install second lockring (31) .
Illustration 12 g00454273
15. Put the governor servo in position on the fuel injection pump housing with piston (34) that
is engaged over rack control sleeve (35) and install the bolts that hold the rack control
sleeve in place.
6/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00591527
3304B engine
Note: The 3304B engine has one stop screw (36) and one locknut (38).
Illustration 14 g00454274
3306B
16. If the stop screws were removed, install two stop screws (36) in collar (37), as shown.
Install locknuts (38) .
7/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00454275
17. Install bolt (41) in block (42), as shown. Install spring (40) on bolt (41), as shown. Put collar
(37) in position on bolt (41) with the hole in the collar in alignment with the notch in bolt
(41) and install bolt (39) in order to hold the collar in place.
Illustration 16 g00454428
Illustration 17 g00459548
8/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 18. Put block (42) in position on housing (43). Align the holes in block (42) with the dowels.
Tighten two bolts (44) .
Illustration 18 g00590080
3304B torque control
19. Assemble the torque control on the 3304B engine. Install retainer (51), two bars (49), spacer
(50), contact (46), and insulator (45) in position on bolts (52) .
9/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 19 g00454429
20. Assemble the torque control on the 3306B, as follows:
a. Install spring (48), spacer (47), contact (46) and spacer (50) on insulator (45), as
shown.
b. Install retainer (51) and bar (49) on bolts (52) .
10/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 20 g00459552
21. Put torque control (53) in position on block (40). Install bolts (54) .
Illustration 21 g00454442
Note: When housing (43) is installed on the fuel injection pump housing, the flange on bolt
(38) must be behind the dashpot. If housing (43) is installed with the flange on bolt (38) on
the wrong side of the dashpot, the riser in the governor will be held in the maximum fuel
delivery position.
22. Install gasket (56) on the fuel injection pump housing. Put housing (43) in position on the
fuel injection pump housing with bolt (38) behind the dashpot, as shown. Install bolts (55)
that hold housing (43) in place.
11/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 22 g00459558
23. Use Tool (C) in order to install lip type seal (57) in the outer governor housing with the lip
inward.
24. Install adjustment screw (58) and the locknut for the high idle adjustment.
Illustration 23 g00459560
25. Install check valve (59) .
12/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 24 g00459562
26. Put lever (60) in position, as shown. Install shaft (61) .
Illustration 25 g00459564
27. Put the gasket and shutoff solenoid (62) in position and install two bolts (63) .
28. Put the gasket and cover (64) in position and install two bolts (65) .
29. Install body (66) and contact (67) .
30. Put the O-ring seal on adapter (68) and put the coupling and adapter (68) in position. Install
two bolts (69) .
Illustration 26 g00459590
31. Install spring (70) in shaft assembly (71). Install pin (72) in shaft assembly (71). The tip of
pin (72) should be engaged in the hole in spring (70). Install pin (73) in shaft assembly (71)
in order to hold pin (72) in place.
13/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 27 g00459593
32. Put stop (76) and plates (74) in position on shaft assembly (71) and install pins (75). Install
snap rings (77) .
Illustration 28 g00459595
33. Put levers (79) and (78) in position in the housing, as shown. Install shaft assembly (71) .
Illustration 29 g00459596
14/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 34. Install low idle adjustment screw (81) and the locknut. Install spring (80) in the hole in the
shaft assembly and in the housing.
Illustration 30 g00454486
35. Use Tool (C) in order to install lip type seal (82) in cover (83) with the lip, as shown. Install
the seal so that the seal is 2.0 ± 1.5 mm (.08 ± .06 inch) below the surface of the cover.
Illustration 31 g00459597
36. Put the gasket and cover (83) in position on the housing and install six bolts (84) .
15/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 32 g00459598
Note: Ensure that seat (85) and spring (86) are on top of lever (79). These parts must be
kept in this position when housing (87) is put in position on the inner governor housing.
37. Install seat (85) and spring (86) on the guide in the housing.
Illustration 33 g00459600
38. Put the gasket and housing (88) in position on the inner governor housing and install six
bolts (87) and two bolts (89) .
16/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Illustration 34 g00459667
39. Install fuel ratio control (90) onto governor (91) .
40. Make the governor adjustments. Refer to the Testing and Adjusting, "Fuel System" topic for
more information on governor adjustments.
End By: Install the fuel injection pump housing and the governor. Refer to the Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 23 09:33:24 UTC+0800 2021
17/17
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 350-A EXCAVATOR 3ML
Configuration: 350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00893695
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-5287 Wrench 1
B 6V-4186 Fuel Pump Timing Pin 1
C 8S-2244 Pump Extractor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1. Remove the bolts and the plate from the side of the fuel injection pump housing.
Illustration 1 g00455790
2. Install Tool (B) in the fuel injection pump housing. Move the fuel rack until Tool (B) can be
installed in order to hold the fuel rack in the center position for removing the fuel injection
pumps.
3. Use Tool (A) in order to remove bushing (1) .
4. Remove the O-ring seal from the fuel injection pump housing.
Illustration 2 g00455791
5. Install Tool (C) on the bonnet and remove the fuel injection pump.
2/3
350 & 350 L Excavators 3ML00001-UP (MACHINE) POWERED BY 3306 Engine(S...
2021/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...