Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service repair manual (mej00001 and up)

Service Repair Manual
Models
D8R TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D8R TRACK-TYPE TRACTOR MEJ
Configuration: D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 3406C Engine
Disassembly and Assembly
D8R Track-Type Tractor Power Train
Media Number -UENR1350-01 Publication Date -01/11/2013 Date Updated -10/03/2016
i05333392
Track Roller Frame - Remove
SMCS - 4151-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A FT-2213 Strap 1
B
9U-7536 Lift Stands 4
277-7200 Pump, Hydraulic 1
C 8T-5255 Hydraulic Jacks 2
D 1P-0074 Slide Hammer Puller Gp 1
E
142-8548 Lifting Bracket As 1
5P-8622 Clevises 3
Start By:
a. Remove bulldozer blade.
Note: May need to position blocks under tracks to raise the rear of machine to install Tooling (B).
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/8D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 3406C...
2020/1/24https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Personal injury can result from performing service on the track roller
frame.
Refer to Special Instruction, SMHS8273 for inspection and removal
procedures before performing any service.
1. Separate the track.
Illustration 1 g03378631
2. Install Tooling (A) to hold the suspension bogies in the correct position.

3. Use Tooling (B) to raise the rear of the machine until the track guides are above the track
links.
4. Use Tooling (B) to raise the front of the tractor with until the track guides are above the
track links.
5. Remove plug (1). Drain the oil from the pivot shaft compartment.

6. Position Tooling (C) under the equalizer bar on the opposite side of the track roller frame
being removed. Raise the equalizer bar until a 25.4 mm (1.00 inch) piece of the bar stock
can be installed between the frame and the equalizer bar. Place the piece on the side of the
track that is being removed. This bar stock keeps the equalizer bar in the original position
during the removal of the track roller frame.
7. Position Tooling (C) under the front track roller frame.

8. Loosen the nuts and bolts (2). Remove equalizer bar pin (3) from the rear track roller frame.
9. Remove bolts (4) from seal retainer (5).
10. Attach a suitable lifting device to trunnion (7). The weight of trunnion (7) is approximately
43 kg (95 lb). Remove bolts (6) and trunnion (7).
11. Remove plug (8) from plate (9).

12. Remove the bolt and the spacer behind plug (8).
13. Use Tooling (D) to remove plate (9).
14. Remove bolts (10) and plate (11). Remove the ring behind plate (11).

Personal injury or death can result from lifting a heavy assembly.
The heavy assembly can fall if using an incorrect hoist to lift the load.
Be sure the hoist has the correct capacity to lift a heavy assembly.
Approximate weight of the assembly is given below.
15. Use a suitable lifting device and Tooling (E) to support weight of track roller frame (12).
The weight of track roller frame (12) is approximately 4350 kg (9600 lb).
16. Remove Tooling (C) from the front track roller frame.
17. Remove track roller frame (12).
18. Remove O-ring seal (13).
Fri Jan 24 23:11:36 UTC+0800 2020

Shutdown SIS
Previous Screen
i05338957
Track Roller Frame - Disassemble
SMCS - 4151-015
Disassembly Procedure
Table 1
Required Tools
A
0S-1587 Bolt (1/2 - 13 by 1 3/4 inch) 1
1F-7958 Full Nut (1/2 - 13) 1
B - Bar Stock (1/2 - 2 by 10 inch) 4
C
1P-0520 Driver Gp 1
8E-2898 Plate 1
1H-3110 Bearing Puller Gp 1
D FT-2213 Strap 1
E
350-7768 Electric Hydraulic Pump Gp (115v) 1
350-7769 Electric Hydraulic Pump Gp (230v)
1U-5197 Hydraulic Cylinder Gp 1
1P-1838 Adapter (1 1/4 - 12) 1
6V-2108 Sleeve 1
6V-3187 Adapter (1 1/4 - 12) 1
5P-4184 Puller Stud (1 1/4 - 12 by 18 inch) 1
F FT-1713 Wedges 2

G 136-1452 Retaining Ring Pliers As 1
H 2D-1201 Eyebolt (5/8 - 11) 1
Start By:
a. Remove the track roller frame.
When you are using hydraulic cylinders and puller studs, always ensure
that the rated capacity of the puller stud meets or exceeds the rated
capacity of the hydraulic cylinder. If the puller stud does not meet or
exceed the rated capacity of the hydraulic cylinder, a sudden failure of
the puller stud could occur. The sudden failure of the puller stud could
result in personal injury or death.
Personal injury can result from performing service on the track roller
frame.
Refer to Special Instruction, SMHS8273 for inspection and removal
procedures before performing any service.
Personal injury or death can result from lifting a heavy assembly.
The heavy assembly can fall if using an incorrect hoist to lift the load.
Be sure the hoist has the correct capacity to lift a heavy assembly.
Approximate weight of the assembly is given below.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Place the track roller frame on a level surface. Support each end of the track roller frame
with the track guides.
2. Remove bolts (1) and retainer (3) from track roller frame (2).
3. Remove the O-ring seal from retainer (3) which seals between the retainer and track roller
frame (2).

4. Position Tooling (A) as shown in Illustration 2. Rotate the nut in order to apply pressure to
plate (4). Separate plate (4) and retainer (5) and insert Tooling (B) to keep plate (4) and
retainer (5) separate. Insert Tooling (B) at four equally spaced locations around retainer (5).
5. Use a soft hammer around the outer diameter of retainer (5) to loosen and remove plate (4).
Note: The 8E-2898 Plate is the same component that is used on the end of the pivot shaft.
Note: Orientation of retainers (5) and (6) for assembly.
6. Use a suitable press and Tooling (C) to remove retainer (6) from retainer (5).

7. Use a suitable press to remove seal (7) from retainer (5).
NOTICE
When these components are removed, the components are damaged or
destroyed.
8. Inspect bearing (8) on each side of the track roller frame for wear and for damage. Remove
bearings (8) from the track roller frame, only if necessary.
9. Use a suitable lifting device to position track roller frame (2) on suitable cribbing. The
weight of track roller frame (2) is approximately 4350 kg (9600 lb). Remove Tooling (D).
10. Mark the track idlers, the caps, and the shims, so that the components are assembled in the
original locations. Remove the track idlers.

Note: Orientation of track rollers (14), caps (13), and the track roller frame for assembly.
11. Attach a suitable lifting device to track roller (14). Remove bolts (12) and caps (13). The
weight of track roller (14) is approximately 98 kg (215 lb). Remove track roller (14) from
the minor bogie. Repeat this procedure for all of the track rollers.
12. Remove bolts (16) and track guides (15) from the major bogies.

Note: Removal of the plugs and stoppers releases oil.
13. Use a variable speed drill to remove plug (17) and stopper (19) from each end of cartridge
pin (18).
14. Repeat Steps 13 through 16 for the remainder of the minor bogies.
15. Install Tooling (E) on the minor bogie. Suspend Tooling with a suitable lifting device.
Remove the cartridge pin.
16. Remove minor bogie (20) from the major bogie.
17. Insert Tooling (F) between the track roller frame and the major bogie to hold the
components in place during the removal of the cartridge pins.

18. Use Tooling (G) to remove retaining ring (21) from each side of the track roller frame.
19. Install Tooling (H) in plate (22). Remove plate (22) from each side of the track roller frame.
Note: Removal of the plugs and stoppers releases oil.
20. Use a variable speed drill to remove plug (23) and stopper (25) from each end of cartridge
pin (24). Remove plugs (26) from each side of the track roller frame.

21. Install Tooling (E) on the major bogie. Use suitable lifting device to support Tooling (E).
Remove the cartridge pins.
22. Attach a suitable lifting device to major bogie (27). The weight of major bogie (27) is
approximately 190 kg (420 lb).
23. Repeat Steps 17 through 21 for the remainder of the major bogies.

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

24. Remove pad assemblies (28) from the track roller frame and from the major bogies.
25. Remove the front track roller frame from the rear track roller frame.
26. Remove the track adjuster.
27. Remove the recoil spring.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jan 24 23:12:36 UTC+0800 2020
10/10D8R TRACK-TYPE TRACTOR MEJ00001-UP (MACHINE) POWERED BY 340...

Shutdown SIS
Previous Screen
i05340179
Track Roller Frame - Assemble
SMCS - 4151-016
Assembly Procedure
Table 1
Required Tools
D FT-2213 Strap 1
G 136-1452 Retaining Ring Pliers As 1
J 5P-7504 Oil Cartridge Pin Lube 1
K - Loctite C5-A Copper Anti-Seize Compound 1
L
5P-4776 Puller Studs (1 - 14 by 18 inch) 2
3K-5234 Hard Washers (6 - 49 mm) 2
1A-1935 Full Nuts (1 -14 inch) 2
6V-3175 Double Acting Cylinder 1
6V-4871 Reaction Bar 1
M 350-7768 Electric Hydraulic Pump Gp (115v) 1
6V-3175 Double Acting Cylinder 1
137-8460 Puller Stud 1

9U-5346 Nut 2
150-1961 Washer 1
5P-8713 Plate 1
6V-0027 Adapter Bearing Puller(1)
1
5P-8707 Adapter Bearing Puller(2)
1
N
1F-7958 Full Nuts (1/2 - 13) 4
- Threaded Rod (1/2 - 13 by 8 inch) 2
5P-8245 Hard Washers (3 - 25.5 mm) 4
P
8T-3053 Seal Installer 1
6V-3141 Puller Plate 1
(1)
Used on Inner Trunnion Bearing.
(2)
Used on Outer Trunnion Bearing.
When you are using hydraulic cylinders and puller studs, always ensure
that the rated capacity of the puller stud meets or exceeds the rated
capacity of the hydraulic cylinder. If the puller stud does not meet or
exceed the rated capacity of the hydraulic cylinder, a sudden failure of
the puller stud could occur. The sudden failure of the puller stud could
result in personal injury or death.
1. Install the recoil spring.
2. Install the track adjuster.
3. Install the front track roller frame in the rear track roller frame.

4. Install pad assemblies (28) on the track roller frame and on the major bogies.
5. Attach a suitable lifting device to major bogie (27). The weight of major bogie (27) is
approximately 190 kg (420 lb). Install major bogie (27) in the track roller frame.
6. Add 60 ± 3 cc of Tooling (J) to the cartridge pins. Install the rubber stoppers to
3.00 ± 1.00 mm (0.118 ± 0.039 inch) below the surface of the pin.
7. Apply Tooling (K) to the bores of the major bogie and to the bores of the track roller frame.
NOTICE
Install the cartridge pin with the Mark (X) on the outside of the track
roller frame. Position the Mark (X) to the top or to the bottom of the
vertical centerline.
8. Install the cartridge pins in both sides of the track roller frame.

Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service repair manual (mej00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (16)

Similar to Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service repair manual (mej00001 and up)

Similar to Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service repair manual (mej00001 and up) (19)

More from udfujjsejkkem

More from udfujjsejkkem (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat d8 r track type tractor dozer bulldozer (prefix mej) service repair manual (mej00001 and up)