Caterpillar cat d11 t track type tractor dozer bulldozer (prefix tpb) service repair manual (tpb00001 and up)

Service Repair Manual
Models
D11T TRACK-TYPE TRACTOR

Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D11T TRACK-TYPE TRACTOR TPB
Configuration: D11T CARRYDOZER TRACK-TYPE TRACTOR TPB00001-UP (MACHINE) POWERED BY C32 Engine
Disassembly and Assembly
D11T Track-Type Tractor Power Train
Media Number -RENR8226-03 Publication Date -01/06/2011 Date Updated -24/06/2011
i02834289
Recoil Spring - Install
SMCS - 4158-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7640 Stand 1
8S-7611 Tube 1
8S-7615 Pin 1
8S-8048 Saddle 1
B 3S-6224 Electric Hydraulic Pump Gp 1
1S-8937 Needle Valve 1
8S-7172 Double Acting Cylinder 1
5P-7269 Plate 1
1J-2921 Bolt 2
5F-9888 Coupling 1
5P-8713 Plate 1
163-9151 Pilot 1
5P-2678 Stud 4
FT-2631 Spacers 8
5P-8249 Hard Washer 4
1/6D11T CARRYDOZER TRACK-TYPE TRACTOR TPB00001-UP (MACHINE) PO...
2020/2/5https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

2J-3505 Full Nut 4
C 1P-0520 Driver Gp 1
D -
Bar Stock
12.7 mm (0.50 inch) by
54.00 mm (2.125 inch) by
609.6 mm (24.00 inch) long
1
Illustration 1 g00553596
NOTICE
Install stop assembly (13) with the large inside diameter toward the
front of the track roller frame.

NOTICE
Do not damage the threads on the inside of the front track roller frame
when the recoil spring is installed.
1. Attach a suitable lifting device to recoil spring (12) and stop assembly (13). The weight of
recoil spring (12) and stop assembly (13) is approximately 522 kg (1150 lb). Install recoil
spring (12) and stop assembly (13) in the front track roller frame.
2. Use a suitable lift truck to install recoil spring (12) and stop assembly (13) into the front
track roller frame.
3. Use Tooling (C) to install bearing (11) in pilot assembly (10) if the bearing was removed.
The inside diameter of the bearing must be 101.100 ± 0.116 mm (3.9803 ± .0045 inch) after
installation.
Note: The recoil spring and the stop assembly must be against the end of the front track
roller frame before pilot assembly (10) is installed.
4. Install pilot assembly (10) in the front track roller frame.

5. Attach a suitable lifting device to recoil spring retainer (9). The weight of recoil spring
retainer (9) is approximately 55 kg (120 lb). Install recoil spring retainer (9) in the front
track roller frame.
6. Tighten recoil spring retainer (9). Use Tooling (D) to tighten recoil spring retainer (9)
enough to contact the pilot assembly. Recoil spring retainer (9) must be installed
approximately 89.0 mm ( 3.50 inch).
Use only the tooling and cylinder listed in this procedure. Do not use
other cylinders because they can cause enough force to break the
tension rods. This can result in personal injury or death.
7. Install Tooling (B). Measure the distance between Surface (C) and 5P-7269 Plate (5) at four
locations next to 5P-2678 Studs. Use 2J-3505 Nuts (7) in order to adjust the plate. Adjust
the distance to 550.0 mm (21.65 inch). Install stops (2) on 5P-2678 Studs (6) to aid in
proper alignment for installation.

The recoil spring must never have more than 12.7 mm (.50 inch)
distance between the recoil spring retainer during installation of the
recoil spring.
8. Slowly extend the cylinder rod in order to compress the recoil spring while recoil spring
retainer (9) is installed. Continue this procedure until the outside of the recoil spring retainer
is 3.0 mm (0.12 inch) inside the front track roller frame.
9. Turn recoil spring retainer (9) until the slots are in alignment. Install stops (2) in the front
track roller frame.
10. Remove Tooling (B) from the front track roller frame.

11. Put stops (2) in position, and install four bolts (1) .
12. Fasten a suitable lifting device to track adjuster (4). Install track adjuster (4) in the front
track roller frame. The weight of track adjuster (4) is approximately 177 Kg (390 lb).
13. Put cable (3) in position on track adjuster (4). Install the spacer, the washer and the bolt that
keeps the cable in place.
End By: Install the front track roller frame. Refer to Disassembly and Assembly, "Track Roller
Frame (Front) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Feb 5 20:59:15 UTC+0800 2020

Shutdown SIS
Previous Screen
i05401049
Track Roller Frame - Remove
SMCS - 4151-011
Removal Procedure
Table 1
Required Tools
A
105-3351 Strap 2
105-3349 Strap 2
B 8S-6470 Forcing Bolt 1
C
8S-7620 Base As 1
8S-7650 Cylinder As 1
8S-7615 Pin 1
3S-6224 Electric Hydraulic Pump Gp 1
D
6V-3160 Double Acting Cylinder 1
9S-5564 Pin Puller Sleeve As 1
4C-9633 Puller Stud 1
1P-0543 Nut 1
E
142-8548 Bracket 1
189-0863 Shackle As 2
193-5474 Shackle As 1

9U-7536 Lift Stand 2
4C-5809 Electric Hydraulic Pump Gp 2
Start By:
A. Remove ladder for left roller frame removal only. Refer to Disassembly and Assembly ,
"Ladder - Remove ".
B. Remove the bulldozer. Refer to Disassembly and Assembly, "Bulldozer - Remove".
C. Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Install Tooling (A) in order to hold the bogies in place when the machine is raised.

Note: Tooling (F) should be placed near the outer edge of the case, forward of the pin bore
for the ripper in order to properly support the weight of the machine. Improper placement of
Tooling (F) could cause damage to the underside of the case.
2. Lift the rear of the machine with Tooling (F) until the track guides are above the track links.
3. Lift the front of the machine with Tooling (F) until the track guides are above the track
links.
4. Remove plug (3) and drain the oil from the pivot shaft into a suitable container for storage
or disposal.
5. Fasten a suitable lifting device to trunnion (1) . The weight of trunnion (1) is approximately
147 kg (325 lb). Remove bolts (2) and trunnion (1) from the track roller frame.

6. Remove plug (6) from plate (5) .
7. Remove spiral lock ring (4) .
8. Install Tooling (B) in plate (5) . Tighten Tooling (B) in order to remove plate (5) from the
track roller frame.

9. Position Tooling (C) under the front track roller frame, as shown. Support the weight of the
roller frame with Tooling (C) .
10. If necessary, remove bolts (21) and washers (22) . Remove plate (24) and washers (23) (not
shown).
11. Remove bolts (8) that hold retainer assembly (7) to the main frame case.
NOTICE

To prevent damage to the pivot shaft seal, make sure the bolts that
hold the pivot shaft seal retainer to the main frame case has been
removed before the equalizer bar is disconnected.
12. If necessary, remove bolts (26) and guard (25) from spacers (27) .
13. Remove bolts (9) and the nuts that clamp pin (10) in place in the track roller frame.
14. Remove the retaining ring and the spacer from the end of pin (10) .

15. Attach Tooling (D) , as shown. Fasten a suitable lifting device to Tooling (D) .
16. Use Tooling (D) to remove pin (10) from the track roller frame.
Personal injury or death can result from lifting a heavy assembly.
The heavy assembly can fall if using an incorrect hoist to lift the load.
Be sure the hoist has the correct capacity to lift a heavy assembly.
Approximate weight of the assembly is given below.
Pinch Point

Stay clear of this area!
Serious personal injury may occur.
17. Fasten a suitable lifting device and Tooling (E) to the track roller frame. Support the weight
of the track roller frame with the suitable lifting device. The weight of the roller frame is
approximately 9979 kg (22000 lb).
18. Remove Tooling (C) from the front frame.
19. Remove bolts (11) and plate (12) that holds the track roller frame to the pivot shaft.
20. Use a suitable lifting device and Tooling (E) to remove the track roller frame.
(13) Thrust plate
21. Remove O-ring seal (15) .

22. Fasten a suitable lifting device to retainer assembly (7) . The weight of retainer assembly (7)
is approximately 34 kg (75 lb). -Remove bolts (14) that hold retainer assembly (7) to the
track roller frame and remove retainer assembly (7) .
23. Remove O-ring seal (17) from retainer (16) .
24. Use a hammer and a chisel to remove seal assembly (18) from retainers (16) and (19) .
25. Remove plate (13) from retainer (7) . Refer to Illustration 14 for the location of plate (13) .
26. If necessary, remove bearings (20) from the track roller frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Feb 5 21:00:04 UTC+0800 2020

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
i06671320
Track Roller Frame - Disassemble
SMCS - 4151-015
Disassembly Procedure
Table 1
Required Tools
A 105-3349 Strap 1
B
6V-3175 Hydraulic Cylinder Gp 1
4C-9634 Puller Stud 1
5P-7270 Sleeve 1
1P-1840 Bearing Puller Adapter 1
9U-6832 Nut 1
3H-0467 Puller Washer 1
C FT-1713 Wedge 1
D 2D-1201 Eyebolt 1
Start By:
a. Remove the track roller frame or the front track roller frame. Refer to Disassembly and
Assembly, "Track Roller Frame - Remove".
b. Remove the idlers. Refer to Disassembly and Assembly, "Idlers - Remove".

NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Note: The disassembly procedure for the track roller frame and the front track roller frame is the
same procedure. Only the front track roller frame is shown.
1. Fasten a suitable lifting device to track roller (1).
2. Remove bolts (3) and caps (2) and remove the track roller. The weight of track roller is
approximately 179 kg (394 lb).
Note: Special Spiralock threads are used on the minor bogies with caps with 2 bolts.
Spiralock threads provide improved bolt retention. Use special Spiralock taps to chase the
threads in these holes. The use of standard taps in these holes will eliminate the Spiralock
feature. This will cause the bolts to loosen.
3. Remove Tooling (A) from the track roller frame.

4. Remove guides (4) and covers (5) from both sides of the track roller frame.
Note: There will be a loss of oil when the stoppers and plug (7) are removed from pin
assembly (6).
5. Use a drill and remove the stoppers and plugs (7) from both ends of pin assembly (6).

6. Put Tooling (B) in position. Fasten a suitable lifting device to Tooling (B). The combined
weight of the pin assembly and Tooling (B) is approximately 45 kg (100 lb).
7. Use Tooling (B) to remove the pin assembly that holds minor bogie (8) to the major bogie.
8. Fasten a suitable lifting device to minor bogie (8). Remove minor bogie (8). The weight of
minor bogie (8) is approximately 39 kg (86 lb).

Caterpillar cat d11 t track type tractor dozer bulldozer (prefix tpb) service repair manual (tpb00001 and up)

Recommended

Recommended

More Related Content

What's hot

What's hot (11)

Similar to Caterpillar cat d11 t track type tractor dozer bulldozer (prefix tpb) service repair manual (tpb00001 and up)

Similar to Caterpillar cat d11 t track type tractor dozer bulldozer (prefix tpb) service repair manual (tpb00001 and up) (13)

More from fujsjekkekmme

More from fujsjekkekmme (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat d11 t track type tractor dozer bulldozer (prefix tpb) service repair manual (tpb00001 and up)