This document provides the service manual contents for a GC/GLC/GDC135-155CA lift truck. It lists the section numbers, part numbers, and revision dates for the service manual sections covering the frame, engines, transmission, differentials, steering, brakes, hydraulics, electrical systems, attachments, and general information. It also provides contact information for ordering service information on Cummins diesel engines.
Yale (d875) glpo060 vx lift truck service repair manualfjskekmsemmwe
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Disconnecting remaining electrical and removing panels/covers to access mounting hardware.
5. Using lifting equipment connected through the cab door openings, carefully lifting the cab off the forklift frame.
Yale (b910) glc050 vx lift truck service repair manualfjskekmsemmwe
This service manual provides information on servicing and repairing various models of GC/GLC lift trucks. The document outlines procedures for removing and installing components like the counterweight, hood, overhead guard, engine, transmission, and covers. It contains sections on the frame description, removing the hood and seat, and replacing side covers. Safety warnings are provided, and diagrams show the locations of parts. Repair sections cover topics such as the cooling system, fuel systems, mast, cylinders, and electrical systems.
The document provides information on servicing the cylinder head, valves, and camshaft of an engine. It includes specifications for parts, torque values for fasteners, and tools needed for the job. The procedures covered can be done with the engine installed in the frame. Cleaning and marking disassembled parts is important to ensure correct reassembly.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...yhhjjkfkseme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Scania industrial and marine engines 12 litre engine service repair manualufjdjfjksekkmm
This document provides work instructions for servicing various components of 12 liter Scania industrial and marine engines, including the complete engine, cylinder head, turbocharger, pistons, flywheel, timing gears, camshaft, crankshaft, cylinder block, and lubrication system. It includes diagrams to identify parts, specifications for different components, and lists of required special tools. Procedures are outlined for removing, inspecting, repairing, and replacing parts as needed.
YALE (C910) GLC050VX LIFT TRUCK Service Repair Manualfujfdjjskfkemd
This is the Highly Detailed factory service repair manual for theYALE (C910) GLC050VX LIFT TRUCK, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.YALE (C910) GLC050VX LIFT TRUCK Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Frame
Kubota spark ignited 2.5l lpg
Psi 2.4l engine
Cooling system
Lpg fuel system, kubota 2.5l engine
Fuel system psi 2.4l
Single speed ps chain drive pto
Drive axle repair - dry brake
Steering axle
Brake system
Hydraulic cleanliness procedures
Hydraulic gear pumps
Main control valve
Cylinder repair (mast s/n f507, f508, f562, f563)
Cylinder repair (mast s/n d515, e509, e564)
Wire harness repair
User interface
Electrical system
Engine electrical system, psi 2.4l engine
Mast repair (s/n f507, f508, f562, f563)
Mast repair (s/n d515, e509, e564)
Metric and inch (sae) fasteners
Calibration procedures
Diagrams and schematics
Periodic maintenance
Capacities and specifications
Diagnostic troubleshooting manual
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveYALE (C910) GLC050VX LIFT TRUCK Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
Volvo ec700 b hr ec700bhr excavator service repair manualjfkseksmemqw
This document provides service information for track gearboxes, including descriptions, troubleshooting, removal/installation procedures, maintenance standards, and precautions for operation. It consists of 3 stages of planetary gearing housed in a rotating casing and is designed for use in crawler undercarriages. Proper lubrication and maintenance are required to prevent issues like leakage, noise, and overheating.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Yale (d875) glpo060 vx lift truck service repair manualfjskekmsemmwe
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Disconnecting remaining electrical and removing panels/covers to access mounting hardware.
5. Using lifting equipment connected through the cab door openings, carefully lifting the cab off the forklift frame.
Yale (b910) glc050 vx lift truck service repair manualfjskekmsemmwe
This service manual provides information on servicing and repairing various models of GC/GLC lift trucks. The document outlines procedures for removing and installing components like the counterweight, hood, overhead guard, engine, transmission, and covers. It contains sections on the frame description, removing the hood and seat, and replacing side covers. Safety warnings are provided, and diagrams show the locations of parts. Repair sections cover topics such as the cooling system, fuel systems, mast, cylinders, and electrical systems.
The document provides information on servicing the cylinder head, valves, and camshaft of an engine. It includes specifications for parts, torque values for fasteners, and tools needed for the job. The procedures covered can be done with the engine installed in the frame. Cleaning and marking disassembled parts is important to ensure correct reassembly.
Caterpillar cat 140 g motor grader (prefix 72v) service repair manual (72v103...yhhjjkfkseme
The document provides instructions for disassembling and assembling the differential of a 140G motor grader. It begins by describing how to remove the differential from the carrier by removing nuts, bolts, locks and wires. It then describes removing additional components from the differential including cages, bearings, pinion and seals. The assembly section provides steps for installing these components in reverse order and includes heating bearings to specific temperatures before installation.
Scania industrial and marine engines 12 litre engine service repair manualufjdjfjksekkmm
This document provides work instructions for servicing various components of 12 liter Scania industrial and marine engines, including the complete engine, cylinder head, turbocharger, pistons, flywheel, timing gears, camshaft, crankshaft, cylinder block, and lubrication system. It includes diagrams to identify parts, specifications for different components, and lists of required special tools. Procedures are outlined for removing, inspecting, repairing, and replacing parts as needed.
YALE (C910) GLC050VX LIFT TRUCK Service Repair Manualfujfdjjskfkemd
This is the Highly Detailed factory service repair manual for theYALE (C910) GLC050VX LIFT TRUCK, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. they are specifically written for the do-it-yourself-er as well as the experienced mechanic.YALE (C910) GLC050VX LIFT TRUCK Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly.
Service Repair Manual Covers:
Frame
Kubota spark ignited 2.5l lpg
Psi 2.4l engine
Cooling system
Lpg fuel system, kubota 2.5l engine
Fuel system psi 2.4l
Single speed ps chain drive pto
Drive axle repair - dry brake
Steering axle
Brake system
Hydraulic cleanliness procedures
Hydraulic gear pumps
Main control valve
Cylinder repair (mast s/n f507, f508, f562, f563)
Cylinder repair (mast s/n d515, e509, e564)
Wire harness repair
User interface
Electrical system
Engine electrical system, psi 2.4l engine
Mast repair (s/n f507, f508, f562, f563)
Mast repair (s/n d515, e509, e564)
Metric and inch (sae) fasteners
Calibration procedures
Diagrams and schematics
Periodic maintenance
Capacities and specifications
Diagnostic troubleshooting manual
File Format: PDF
Compatible: All Versions of Windows & Mac
Language: English
Requirements: Adobe PDF Reader
NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveYALE (C910) GLC050VX LIFT TRUCK Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check:
https://www.aservicemanualpdf.com/
Thanks for visiting!
Volvo ec700 b hr ec700bhr excavator service repair manualjfkseksmemqw
This document provides service information for track gearboxes, including descriptions, troubleshooting, removal/installation procedures, maintenance standards, and precautions for operation. It consists of 3 stages of planetary gearing housed in a rotating casing and is designed for use in crawler undercarriages. Proper lubrication and maintenance are required to prevent issues like leakage, noise, and overheating.
Jcb 560 80 tier 4 telescopic handler service repair manual sn from 2460601 on...fusefjjskekemm
The document provides instructions for servicing fuel injectors and related components on JCB Loadall vehicles. It begins with an introduction to fuel injectors and their purpose. The main sections include checking injector operation using leak-off tests, removing and installing individual injectors, removing and installing injector seals, and removing and installing the common fuel rail assembly. Torque specifications are provided for reinstalling components.
Jcb 9 tft dumper service repair manual sn from hrm1382 to hrm4003fusefjskekkmem
This service manual provides instructions for servicing the braking system of dumpers. It contains information on health and safety when working on the brakes, technical specifications, component identification, troubleshooting, and bleeding the brakes. The braking system uses mineral oil and contains separate front and rear brake circuits for safety. Adjustment is generally not needed as the brakes are self-adjusting, but bleeding may be required if the brake lines leak fluid.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upfiskefjskemem
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics, and electrical systems. Specific models covered include 526-56, 531-70, 533-105, 535-95, 536-60, and others. Safety warnings are provided throughout and procedures for removal and installation are described in detail with torque specifications.
Jcb 3 cx backhoe loader service repair manual sn from 2442701 to 2451000fusefjskekkmem
This service manual section provides information on servicing the crankshaft and related components on a backhoe loader. It includes identification of parts, technical specifications, operation descriptions, removal and installation instructions, and check/inspection procedures. Proper cleaning and installation of the crankshaft oil seal is critical to prevent oil leakage. Removal and installation of the crankshaft requires carefully following all steps while ensuring components remain clean and undamaged.
Claas axion 850 810 (type a09) tractor service repair manualfusefjskekkmem
1) The document provides instructions for removing and refitting the front axle, epicycloid reducer, and joint unit on a CLAAS AXION 850-810 tractor.
2) Key steps when removing the front axle include draining fluids, removing mounting hardware, wheels, and radiator components.
3) Dismantling the epicycloid reducer involves removing gears, bearings, seals, and mounting components.
4) Removing the joint unit requires taking off the steering bars, supports, and wheel shaft.
Jcb 536 70 telescopic handler service repair manual sn 2460601 and upfujsjefjwerkskemm
This service manual section contains information about JCB diesel engines. It provides a basic description of engine components and operation, including the starter motor, fuel injection system, lubrication system, and ancillary drive components. The manual identifies internal engine parts such as pistons, connecting rods, valves, bearings, and gears. It specifies that all components should be renewed if worn and that leakages should be prevented during maintenance.
Caterpillar cat 140 h motor grader (prefix apm) service repair manual (apm000...yhhjjkfkseme
This document provides disassembly instructions for the transmission of a 140H motor grader. It lists over 30 steps to fully disassemble the transmission, including removing components like the transmission case assembly, shaft assemblies, seals, gears, clutches, and pistons. Detailed illustrations accompany each step and special tools are required to properly separate parts and compress components during disassembly.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
Caterpillar cat 140 g motor grader (prefix 5md) service repair manual (5md000...fjjsefkksemme
This service repair manual provides instructions for disassembling and assembling various components of a 140G motor grader, including:
1) Removing and installing brake and wheel spindle housings, which includes releasing air pressure and removing nuts, guards, and air lines.
2) Removing and installing tandem housings, which are attached to the final drive housing with nuts.
3) Removing and installing drive sprockets by removing nuts with a tool and ensuring proper preload on bearings.
Claas celtis 456 426 ra (type a07) tractor service repair manualfjsjjekdkme
This document provides technical specifications and inspection procedures for engine components including the cylinder head, valves, turbocharger, and head gasket of a Celtis engine. It includes dimensions, diagrams, and step-by-step checks to identify potential issues such as coolant or gas leaks between the cylinder head and engine block. Symptoms and causes of combustion gas and coolant sealing failures are outlined to guide troubleshooting and repair.
Yale c879 gdc70 vx lift truck service repair manualjfjskekdhnejd
This document provides instructions for removing and installing the hood, seat, dash, and side covers on GLC/GDC60VX and GLC/GDC70VX lift trucks. Key steps include removing the floor plate, side panels, fenders, dash, and kick panel. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation follows the reverse order, ensuring the gas springs and hood latch are properly adjusted.
Yale c879 glc60 vx lift truck service repair manualfjjskdmnenemm
The document provides instructions for removing and installing the hood, seat, dash, and side covers on a lift truck. Key steps include removing the floor plate, side panels, fenders, steering column covers, dash, and kick panel. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation involves reversing these steps, making sure the hood latch striker aligns properly and the gas springs are installed in the correct holes based on the seat type.
Yale c879 glc70 vx lift truck service repair manualjkmsme ekdmm
This document provides instructions for replacing the hood, seat, dash, and side covers on a lift truck. Key steps include removing the floor plate, side panels, fender covers, steering column covers, dash, kick panel, and seal plate. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation involves reversing these steps, ensuring the hood latch striker aligns properly and the hood closes fully with two clicks.
Yale c879 glc70 vx lift truck service repair manualfjjskekdmmme
The document provides instructions for removing and installing the hood, seat, dash, and side covers of a lift truck. Key steps include removing the floor plate, side panels, fender covers, steering column covers, dash, kick panel, and seal plate. The hood is then removed by taking out the hinge screws and gas springs. Reinstallation follows the reverse order, making sure the hood latch striker aligns properly and the hood closes fully with two clicks.
Yale c879 gdc60 vx lift truck service repair manualfhhsjdkmem
The document provides instructions for removing and installing the hood, seat, dash, and side covers of a lift truck. Key steps include removing the floor plate, side panels, fenders, steering column covers, dash, and kick panel. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation involves reversing these steps, making sure the hood latch striker aligns properly and the gas springs are installed in the correct holes based on the seat type.
YALE (D875) GLPO050VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP060VX LIFT TRUCK Service Repair Manual.pdfkgo7715345
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP050VX LIFT TRUCK Service Repair Manual.pdfufjskedkdm8ud
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GDP070VX LIFT TRUCK Service Repair Manual.pdfhei510572ni
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GDP040VX LIFT TRUCK Service Repair Manual.pdfttf99929781
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP060VX LIFT TRUCK Service Repair Manual.pdfhei510572ni
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GLPO060VX LIFT TRUCK Service Repair Manual.pdfufjskedkdm8ud
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GTP050VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
Jcb 9 tft dumper service repair manual sn from hrm1382 to hrm4003fusefjskekkmem
This service manual provides instructions for servicing the braking system of dumpers. It contains information on health and safety when working on the brakes, technical specifications, component identification, troubleshooting, and bleeding the brakes. The braking system uses mineral oil and contains separate front and rear brake circuits for safety. Adjustment is generally not needed as the brakes are self-adjusting, but bleeding may be required if the brake lines leak fluid.
Jcb 536 t70 lp telescopic handler service repair manual sn 2336575 and upfiskefjskemem
This service manual provides instructions for servicing Loadall rough terrain variable reach trucks. It contains sections on machine systems and components including the engine, fuel system, cooling system, brakes, hydraulics, and electrical systems. Specific models covered include 526-56, 531-70, 533-105, 535-95, 536-60, and others. Safety warnings are provided throughout and procedures for removal and installation are described in detail with torque specifications.
Jcb 3 cx backhoe loader service repair manual sn from 2442701 to 2451000fusefjskekkmem
This service manual section provides information on servicing the crankshaft and related components on a backhoe loader. It includes identification of parts, technical specifications, operation descriptions, removal and installation instructions, and check/inspection procedures. Proper cleaning and installation of the crankshaft oil seal is critical to prevent oil leakage. Removal and installation of the crankshaft requires carefully following all steps while ensuring components remain clean and undamaged.
Claas axion 850 810 (type a09) tractor service repair manualfusefjskekkmem
1) The document provides instructions for removing and refitting the front axle, epicycloid reducer, and joint unit on a CLAAS AXION 850-810 tractor.
2) Key steps when removing the front axle include draining fluids, removing mounting hardware, wheels, and radiator components.
3) Dismantling the epicycloid reducer involves removing gears, bearings, seals, and mounting components.
4) Removing the joint unit requires taking off the steering bars, supports, and wheel shaft.
Jcb 536 70 telescopic handler service repair manual sn 2460601 and upfujsjefjwerkskemm
This service manual section contains information about JCB diesel engines. It provides a basic description of engine components and operation, including the starter motor, fuel injection system, lubrication system, and ancillary drive components. The manual identifies internal engine parts such as pistons, connecting rods, valves, bearings, and gears. It specifies that all components should be renewed if worn and that leakages should be prevented during maintenance.
Caterpillar cat 140 h motor grader (prefix apm) service repair manual (apm000...yhhjjkfkseme
This document provides disassembly instructions for the transmission of a 140H motor grader. It lists over 30 steps to fully disassemble the transmission, including removing components like the transmission case assembly, shaft assemblies, seals, gears, clutches, and pistons. Detailed illustrations accompany each step and special tools are required to properly separate parts and compress components during disassembly.
Jcb js130 excavator service repair manual sn from 2373080 to 2375080fiskefjskemem
The document provides a service manual for excavator tracks. It includes sections on track components, measuring wear using technical data tables, adjusting tracks, removing and installing tracks, and storing tracks. Procedures are provided for measuring link rail surface wear, track pitch/internal pin and bush wear, and bush external wear to determine wear percentages and maintenance requirements.
Caterpillar cat 140 g motor grader (prefix 5md) service repair manual (5md000...fjjsefkksemme
This service repair manual provides instructions for disassembling and assembling various components of a 140G motor grader, including:
1) Removing and installing brake and wheel spindle housings, which includes releasing air pressure and removing nuts, guards, and air lines.
2) Removing and installing tandem housings, which are attached to the final drive housing with nuts.
3) Removing and installing drive sprockets by removing nuts with a tool and ensuring proper preload on bearings.
Claas celtis 456 426 ra (type a07) tractor service repair manualfjsjjekdkme
This document provides technical specifications and inspection procedures for engine components including the cylinder head, valves, turbocharger, and head gasket of a Celtis engine. It includes dimensions, diagrams, and step-by-step checks to identify potential issues such as coolant or gas leaks between the cylinder head and engine block. Symptoms and causes of combustion gas and coolant sealing failures are outlined to guide troubleshooting and repair.
Yale c879 gdc70 vx lift truck service repair manualjfjskekdhnejd
This document provides instructions for removing and installing the hood, seat, dash, and side covers on GLC/GDC60VX and GLC/GDC70VX lift trucks. Key steps include removing the floor plate, side panels, fenders, dash, and kick panel. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation follows the reverse order, ensuring the gas springs and hood latch are properly adjusted.
Yale c879 glc60 vx lift truck service repair manualfjjskdmnenemm
The document provides instructions for removing and installing the hood, seat, dash, and side covers on a lift truck. Key steps include removing the floor plate, side panels, fenders, steering column covers, dash, and kick panel. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation involves reversing these steps, making sure the hood latch striker aligns properly and the gas springs are installed in the correct holes based on the seat type.
Yale c879 glc70 vx lift truck service repair manualjkmsme ekdmm
This document provides instructions for replacing the hood, seat, dash, and side covers on a lift truck. Key steps include removing the floor plate, side panels, fender covers, steering column covers, dash, kick panel, and seal plate. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation involves reversing these steps, ensuring the hood latch striker aligns properly and the hood closes fully with two clicks.
Yale c879 glc70 vx lift truck service repair manualfjjskekdmmme
The document provides instructions for removing and installing the hood, seat, dash, and side covers of a lift truck. Key steps include removing the floor plate, side panels, fender covers, steering column covers, dash, kick panel, and seal plate. The hood is then removed by taking out the hinge screws and gas springs. Reinstallation follows the reverse order, making sure the hood latch striker aligns properly and the hood closes fully with two clicks.
Yale c879 gdc60 vx lift truck service repair manualfhhsjdkmem
The document provides instructions for removing and installing the hood, seat, dash, and side covers of a lift truck. Key steps include removing the floor plate, side panels, fenders, steering column covers, dash, and kick panel. The gas springs and hinge screws are then removed to lift the hood off the frame. Reinstallation involves reversing these steps, making sure the hood latch striker aligns properly and the gas springs are installed in the correct holes based on the seat type.
YALE (D875) GLPO050VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP060VX LIFT TRUCK Service Repair Manual.pdfkgo7715345
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP050VX LIFT TRUCK Service Repair Manual.pdfufjskedkdm8ud
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GDP070VX LIFT TRUCK Service Repair Manual.pdfhei510572ni
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GDP040VX LIFT TRUCK Service Repair Manual.pdfttf99929781
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP060VX LIFT TRUCK Service Repair Manual.pdfhei510572ni
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GLPO060VX LIFT TRUCK Service Repair Manual.pdfufjskedkdm8ud
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GTP050VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GDP060VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator cover/cap, and disconnecting heater hoses from the engine.
3. Removing doors by disconnecting gas springs, lifting doors off hinges, and disconnecting electrical connections.
4. Removing dash/floor components and disconnecting cab mounting capscrews and flange nuts to separate the cab from the forklift frame. The cab can then be lifted away for replacement or repair.
YALE (D875) GTP070VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GP050VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GTP040VX LIFT TRUCK Service Repair Manual.pdffujsjekmd8udidj
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GP040VX LIFT TRUCK Service Repair Manual.pdffujsjkdmdm3e4
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column up, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, removing radiator covers, and draining coolant lines.
3. For models with air conditioning, extracting refrigerant and disconnecting AC lines.
4. Disconnecting wiring harnesses, heater lines, gas springs and removing door assemblies. The cab can then be lifted off as a complete unit.
YALE (D875) GDP040VX LIFT TRUCK Service Repair Manual.pdfufjskedkdm8ud
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
YALE (D875) GP060VX LIFT TRUCK Service Repair Manual.pdfufjskedkdm8ud
The document provides instructions for removing an operator cab from a forklift. Key steps include:
1. Tilting the steering column, sliding the seat forward, opening rear doors/windows, and disconnecting the battery.
2. Disconnecting air filter hoses, radiator hoses, heater hoses, electrical connections, and removing doors.
3. Removing fasteners securing various cab components like the dash, kick panel, and seal plate.
4. Detaching the cab from the frame by removing front and rear mounting fasteners and carefully lifting the cab away using lifting straps or a spreader bar placed through the door openings.
Similar to Yale a879 gdc135 155 ca lift truck service repair manual (20)
Bomag bw 154 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 154 ac 4 tandem rollers service repair manualfhjsjkdmemm
The document provides technical specifications and adjustment values for Tandem Rollers models BW 141 AD Serie 4 and BW 154 AD Serie 4. It includes details on the engine, travel pump, travel motors, drum reduction gear, vibration pump, vibration motor, steering and charge pump, and filling capacities. The specifications are broken out by component and include information like component type, system, displacement, pressure levels, speeds, ratios, and approved lubricants.
Bomag bw 151 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 151 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 151 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The safety section emphasizes that the machine must only be used for its intended purposes of compacting asphalt and soil and stresses the importance of following all safety instructions.
Bomag bw 141 ad 4 tandem rollers service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 141 AD-4, BW 151 AD-4, BW 151 AC-4, and BW 161 ADCV. It includes sections on safety regulations, controls and indicators, operation, maintenance, and troubleshooting. The technical data section specifies the dimensions, weights, engine, and other technical specifications for each roller model.
Bomag bw 141 ad tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD, BW 154 AD, and BW 154 AD AM. It includes specifications for the Deutz diesel engine like power output, idle speeds, and valve clearances. It also lists components of the travel, vibration, and steering systems along with their types, displacement volumes, pressure settings, and other parameters. Filling capacities are provided for engine oil, hydraulic oil, and other fluids.
Bomag bw 141 ac 4 tandem rollers service repair manualfhjsjkdmemm
This document provides technical data and adjustment values for Tandem Rollers including the BW 141 AD Serie 4, BW 154 AD Serie 4, and BW 154 AD AM Serie 4. It includes specifications for the Deutz diesel engine, travel pump and motors, vibration pump and motors, steering pump, and filling capacities. The data is presented in a table format with specifications such as engine power, pump displacement volumes, pressure settings, and fluid capacities.
Bomag bw 135 ad single tandem vibratory roller service repair manualfhjsjkdmemm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers. It includes technical specifications, safety regulations, descriptions of indicators and controls, operating instructions, maintenance instructions, and troubleshooting information. Safety is emphasized, including intended and prohibited uses of the machines, and potential hazards are outlined.
Hyundai r170 w 7a wheel excavator service repair manualfhjsjkdmemm
The document provides instructions for removing and installing a swing motor, disassembling and assembling the swing motor, removing and installing a reduction gear, and disassembling and assembling the reduction gear of an excavator. The summary is as follows:
1. The removal and installation instructions for the swing motor include disconnecting hoses and mounting bolts, and removing the swing motor assembly. Installation is the reverse of removal.
2. Disassembling the swing motor involves removing components like the valve, casing, piston, and shaft. Assembly is the reverse of disassembly.
3. Removal and installation of the reduction gear involves slinging and removing/installing mounting bolts.
Caterpillar cat 336 f excavator (prefix dsw) service repair manual (dsw00001 ...fhjsjkdmemm
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing the motor head assembly, piston assemblies, barrel assembly, friction plates, seals, springs, and other internal components. Detailed illustrations are provided to identify each part mentioned in the procedure. Safety precautions are noted throughout to warn of potential spring forces or fluid containment. The goal is to break down the travel motor into its core components while maintaining the correct orientation of parts for reassembly.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix xbh) service repair manual (xbh000...fhjsjkdmemm
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar cat 336 d2 l excavator (prefix wdc) service repair manual (wdc000...fhjsjkdmemm
The document provides instructions for assembling a piston motor. It details 17 steps to install various parts like bearings, seals, springs, and retaining rings. Safety precautions are included to properly handle parts under spring tension. The assembly ends by installing the head and bolts.
Caterpillar cat 336 d2 l excavator (prefix wbc) service repair manual (wbc000...fhjsjkdmemm
The document provides instructions for removing and installing various engine components, including:
- Valve guides are removed from the cylinder head using a valve guide driver tool. New guides are installed using driver tools until the proper height is reached.
- Valve seat inserts are removed from the cylinder head using extractors. New inserts are installed using a driver tool after being cooled.
- The engine oil filter base, oil filter, and oil cooler are removed. Hoses are disconnected and bolts removed to access these components.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...fhjsjkdmemm
1. The document provides instructions for disassembling and assembling the piston pump of a 336D2 excavator.
2. The disassembly process involves removing 27 individual parts in a specific order, taking care with spring-loaded components.
3. Reassembly requires installing the parts in the reverse order, with some components requiring special tools or heating/cooling during installation. Proper end play must be verified during assembly.
Caterpillar cat 336 d2 l excavator (prefix ggh) service repair manual (ggh000...fhjsjkdmemm
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of an excavator model 336D2. The disassembly procedure involves removing 22 parts from the pump housing, including springs, seals, pistons, and bearings. The assembly procedure lists 30 steps to reinstall the parts in reverse order and adjust clearances using various tools. Precautions are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...fhjsjkdmemm
This document provides instructions for installing a final drive and travel motor on an excavator. It outlines 11 steps, including positioning the travel motor and final drive with lifting devices, installing O-rings and seals, connecting hoses and fittings, and tightening bolts to specified torques. Safety notices are provided to handle fluids properly and keep components clean from contaminants. Required tools include vacuum caps, link brackets, and anti-seize compound.
Caterpillar cat 336 d2 l excavator (prefix elr) service repair manual (elr000...fhjsjkdmemm
This document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the process is reversed - mounting bolts are installed and all connections reattached. Proper cleaning and use of new O-rings is emphasized to prevent contamination.
Caterpillar cat 336 d2 l excavator (prefix eft) service repair manual (eft000...fhjsjkdmemm
This document provides instructions for disassembling and assembling the travel motor on 336D2 and 336D2 L excavators. The disassembly process involves using various tools to remove components like retaining rings, seals, pistons, springs, and bearings. The assembly process describes installing these components in reverse order and notes that cleanliness is important, components should be lubricated, and parts must be installed in their proper positions and orientations.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker Jamieson
Yale a879 gdc135 155 ca lift truck service repair manual
1. GC/GLC/GDC135-155CA (A879)
SERVICE MANUAL CONTENTS
SECTION
PART
NUMBER
YRM
NUMBER
REV
DATE
FRAME............................................................................................................................ 524192611 0100 YRM 0449 02/07
GM ENGINES.................................................................................................................. 524153897 0600 YRM 0590 04/14
PERKINS DIESEL ENGINE............................................................................................ 524150774 0600 YRM 0705 03/06
COOLING SYSTEM........................................................................................................ 524150775 0700 YRM 0626 03/03
LPG FUEL SYSTEM....................................................................................................... 524153900 0900 YRM 0348 03/03
2-SPEED POWERSHIFT TRANSMISSION DESCRIPTION AND OPERATION........... 524185156 1300 YRM 0324 10/03
2-SPEED POWERSHIFT TRANSMISSION REPAIR..................................................... 524185157 1300 YRM 0325 10/03
DIFFERENTIAL............................................................................................................... 524150779 1400 YRM 0046 08/12
DRIVE AXLE................................................................................................................... 524192612 1400 YRM 0450 09/03
STEERING CONTROL UNIT.......................................................................................... 524185160 1600 YRM 0054 10/03
STEERING AXLE............................................................................................................ 524192613 1600 YRM 0451 09/03
BRAKE SYSTEM............................................................................................................ 524192614 1800 YRM 0452 02/04
HYDRAULIC GEAR PUMP............................................................................................. 524153907 1900 YRM 0097 05/12
HYDRAULIC ASSEMBLY PUMP................................................................................... 524153908 1900 YRM 0339 10/03
HYDRAULIC SYSTEM.................................................................................................... 524192615 1900 YRM 0453 09/03
MAIN CONTROL VALVE................................................................................................ 524185164 2000 YRM 0090 10/03
TILT CYLINDERS........................................................................................................... 524150790 2100 YRM 0103 03/07
ALTERNATOR................................................................................................................ 524150791 2200 YRM 0002 12/04
STARTER........................................................................................................................ 524150792 2200 YRM 0106 12/04
HIGH ENERGY IGNITION (HEI) SYSTEM..................................................................... 524153914 2200 YRM 0107 03/08
INSTRUMENT PANEL INDICATORS AND SENDERS................................................. 524185165 2200 YRM 0143 02/07
MICROPROCESSOR SPARK TIMING SYSTEM (GM 3.0L/4.3L) (LATER MODELS). 524153916 2200 YRM 0765 03/03
EEC-DESCRIPTION AND OPERATION (GM 3.0L/4.3L)............................................... 524153917 2200 YRM 0781 03/03
EEC-TROUBLESHOOTING AND REPAIR.................................................................... 524153918 2200 YRM 0782 03/03
LIFT CYLINDERS........................................................................................................... 524150794 4000 YRM 0135 03/11
MAST DESCRIPTION AND REPAIR.............................................................................. 524185167 4000 YRM 0329 09/10
METRIC AND INCH (SAE) FASTENERS....................................................................... 524150797 8000 YRM 0231 10/13
PERIODIC MAINTENANCE............................................................................................ 524192617 8000 YRM 0393 06/09
CAPACITIES AND SPECIFICATIONS........................................................................... 524192616 8000 YRM 0454 10/03
DIAGRAMS..................................................................................................................... 524185171 8000 YRM 0519 06/07
Service information for Cummins diesel engines can be ordered through the Hyster Literature Distribution Center.
PART NO. 524192610 (04/14)
2. 100 YRM 449 Description
General
This section has the description and repair procedures for the frame and connected parts. Included in this section
are the frame, counterweight, hood, hydraulic and fuel tanks, radiator, and exhaust system. Also included are the
instructions for removal and installation of the engine.
Description
The frame is a one-piece weldment and has mounts for the counterweight, upright, overhead guard, engine and
transmission, axles, and other parts. See Figure 1.
1. HOOD
2. FLOOR PLATE
3. OVERHEAD GUARD
4. COUNTERWEIGHT
5. FRAME
Figure 1. Frame and Connected Parts
1
3. Counterweight Repair 100 YRM 449
Counterweight Repair
REMOVE
WARNING
The lift truck must be put on blocks for some types
of maintenance and repair. The removal of the fol-
lowing assemblies causes large changes in the cen-
ter of gravity: upright, drive axle, engine and trans-
mission, and the counterweight. When the lift truck
is put on blocks, put additional blocks in the follow-
ing positions to maintain stability:
a. Before removing the upright and drive axle, put
blocks under the counterweight so that the lift
truck cannot fall backward.
b. Before removing the counterweight, put blocks
under the upright assembly so that the lift truck
cannot fall forward.
The surface must be solid, even, and level when the
lift truck is put on blocks. Make sure that any blocks
used to support the lift truck are solid, one piece
units.
Do not operate the lift truck if the capscrews for
the counterweight are not installed. When the cap-
screw is removed, the counterweight can fall from
the lift truck.
WARNING
Make sure any lifting devices have the correct ca-
pacity for the parts being moved. See Figure 2.
1. If the lift truck has an LPG fuel system, remove the
LPG tank and bracket so that the counterweight can
be removed. See Figure 2.
WARNING
LPG can cause an explosion. Do not cause sparks
or permit flammable material near the LPG system.
LPG fuel systems can be disconnected indoors
only if the lift truck is at least 8 m (25 ft) from any
open flame, motor vehicles, electrical equipment,
or ignition source.
Close the fuel valve on the LPG tank before any part
of the engine fuel system is disconnected. Run the
engine until the fuel in the system is used and the
engine stops.
If the engine will not run, close the fuel valve on the
LPG tank. Loosen the fitting on the supply hose
from the LPG tank where it enters the filter unit.
Permit the pressure in the fuel system to decrease
slowly. Fuel leaving the fitting removes heat. Use a
cloth to protect your hands from the cold fitting.
2. Use the following procedure to remove the LPG
tank:
a. Removable LPG tanks can be removed and re-
placed indoors only if the lift truck is at least 8 m
(25 ft) from any open flame or ignition source.
b. Move the lift truck to the area where tanks are
changed.
c. Turn the tank fuel valve clockwise until the valve
is completely closed.
d. Run the engine until it stops, then turn the key
switch to the OFF position.
Weight of Counterweights
GLC135CA (GC/GDC/
GLC135CA)
2873 to 2953 kg
(6335 to 6511 lb)
GLC155CA (GC/GDC/
GLC155CA)
3330 to 3420 kg
(7343 to 7541 lb)
1. LIFT TRUCK
FRAME
2. COUNTERWEIGHT
3. GRILL
4. CAPSCREW
5. ACCESS DOOR
6. TRANSITION
PLATE
7. HOOD
Figure 2. Counterweight
2
4. 100 YRM 449 Hood Repair
e. Disconnect the quick disconnect fitting.
f. Release the LPG tank latch and remove the
tank from the bracket.
3. Open the access door between the counterweight
and the hood. Remove the LPG tank and tank
bracket if the unit has the LPG fuel system.
4. Install a lifting eye in the hole in the top of the coun-
terweight. Connect a lifting device to the lifting eye.
Remove the two vertical capscrews and the cap-
screw behind the tow pin that hold the counter-
weight to the frame.
5. Lift the counterweight from the frame. Put the coun-
terweight in a position so that it has stability and will
not fall.
INSTALL
1. Connect a lifting device to the lifting eye on the
counterweight. Lift the counterweight into position
on the frame. See Figure 2.
2. Install the capscrews for the counterweight.
Tighten the capscrews to 655 N•m (485 lbf ft).
3. Close the access door. Install the LPG tank on LPG
units.
Hood Repair
REMOVE
1. Remove the capscrews that fasten the transition
plate. Do NOT remove the plate. See Figure 2.
2. Open the access door, reach under the transition
plate, and remove the radiator overflow hose from
the two J clamps.
3. Raise the hood and disconnect the gas assist cylin-
der at the hood. Remove the hood, transition plate,
and access door.
INSTALL
1. Install the hood, transition plate, and access door
in position on the lift truck. Install the capscrews for
the transition plate. Connect the gas assist cylinder
to the hood. Align the hood for the latch on the
front cover. Tighten the capscrews for the transition
plate.
2. Install the overflow hose in the J clamps. Close the
access door.
WARNING
The hood, hood latch, and latch striker must be cor-
rectly adjusted for the correct operation of the op-
erator restraint system.
3. Use the following procedure to adjust the hood latch
(see Figure 3):
a. Install the floor plates and tighten the cap-
screws.
b. Install the latch striker in the highest slot posi-
tion on the rear floor plate. Check that the latch
striker is in the center of the jaws of the hood
latch.
c. Close the hood to the fully-closed position. The
hood latch has two positions. The hood is fully
closed after two clicks of the latch.
d. Loosen the capscrews for the latch striker just
enough to let the striker move. Push the hood
down until the hood just touches the rubber
bumpers on the frame. Make sure the latch
striker is still in the center of the hood latch.
Tighten the capscrews for the latch striker.
e. Check the operation of the hood latch. Have
an operator sit in the seat. Make sure the hood
is fully closed (two clicks). Also check that the
hood touches the rubber bumpers. If neces-
sary, repeat Step d.
3
5. Overhead Guard Repair 100 YRM 449
A. GAS/DIESEL ARRANGEMENT B. LPG ARRANGEMENT
1. LATCH STRIKER
2. HOOD LATCH
3. LATCH LEVER
4. SEAT
5. SEAT BELT LATCH
6. HIP RESTRAINT
7. SEAT RAIL
8. FLOOR PLATE
9. HOOD
10. GAS CYLINDER
11. HINGE
Figure 3. Hood and Seat Latches Check
Overhead Guard Repair
REMOVE
WARNING
Do not operate the lift truck without the overhead
guard correctly fastened to the lift truck.
Changes that are made by welding or by drilling
holes that are too big in the wrong location, can re-
duce the strength of the overhead guard. See the
instructions for Changes to the Overhead Guard in
the Periodic Maintenance section included with this
lift truck.
Connect a lifting device to the top of the overhead
guard. If installed, remove the overhead exhaust and
LPG fuel line clamps. If installed, disconnect the light
wiring harness. Remove the capscrews that hold the
overhead guard to the frame. Remove the capscrews
that hold the overhead guard to the cowl. Lift the
overhead guard from the lift truck.
INSTALL
1. Connect a lifting device to the top of the overhead
guard. Put the overhead guard in position on the lift
truck.
2. Install the capscrews at the rear of the overhead
guard. Install the capscrews that hold the overhead
guard to the cowl. Tighten the rear and top front
capscrews to 90 N•m (67 lbf ft). Tighten the front
capscrews under the cowl to 165 N•m (122 lbf ft).
3. If removed, install the overhead exhaust and LPG
fuel line. Connect the light wiring harness.
4
6. 100 YRM 449 Operator Restraint System Repair
Operator Restraint System Repair
The seat belt, hip restraint brackets, seat and mount-
ing, hood, latches, and floor plates are all part of the
operator restraint system. Each item must be checked
to make sure it is attached securely, functions correctly,
and is in good condition.
AUTOMATIC LOCKING RETRACTOR (ALR)
NOTE: Lift trucks produced before November 2005 are
equipped with the ALR type seat belts.
The seat belt must fasten securely. Make sure the seat
belt extends and retracts smoothly and is not frayed or
torn. If the seat belt is damaged or does not operate
properly, it must be replaced. See Figure 4.
EMERGENCY LOCKING RETRACTOR
(ELR)
NOTE: Lift trucks produced after November 2005 are
equipped with the Emergency Locking Retractor (ELR)
style seat belt.
When the ELR style seat belt is properly buckled across
the operator, the belt will permit slight operator reposi-
tioning without activating the locking mechanism. If the
truck tips, travels off a dock, or comes to a sudden stop,
the locking mechanism will be activated and hold the
operator’s lower torso in the seat.
A seat belt that is damaged worn or does not operate
properly will not give protection when it is needed. The
end of the belt must fasten correctly in the latch. The
seat belt must be in good condition. Replace the seat
belt if damage or wear is seen. See Figure 4.
1. FORWARD/BACKWARD ADJUSTMENT
2. SWIVEL ADJUSTMENT
3. OPERATOR WEIGHT ADJUSTMENT
4. SEAT POSITION ADJUSTMENT (SEAT RAIL)
5. SET BELT
Figure 4. Operator Restraint System (Swivel Seat Shown)
5
7. Fuel and Hydraulic Tanks Repair 100 YRM 449
The following seat belt operation checks must be per-
formed:
• With the hood closed and in the locked position, pull
the seat belt slowly from the retractor assembly. Make
sure the seat belt pulls out and retracts smoothly. if
the seat belt cannot be pulled from the retractor as-
sembly or the belt will not retract, replace the seat belt
assembly.
• With the hood closed and in the locked position, pull
the seat belt with a sudden jerk. Make sure the seat
belt will not pull from the retractor assembly. If the
seat belt can be pulled from the retractor, when it is
pulled with a sudden jerk, replace the seat belt as-
sembly.
• With the hood in the open position, make sure the
seat belt will not pull from the retractor assembly. If
the seat belt can be pulled from the retractor, with
the hood in the open position, replace the seat belt
assembly.
Make sure the seat rails and latch striker are not loose.
See Figure 3. The seat rails must lock tightly in position,
but move freely when unlocked. The seat rails must be
correctly fastened to the mount surface. If the mount
surface is the hood, the hood must be fastened to the
floor plate with the latch. The floor plate must be fas-
tened to the lift truck frame. Try to lift the hood to make
sure it is fastened correctly and will not move.
Adjust the hood, hood latch, and latch striker when any
of the parts of the operator restraint system are installed
or replaced. See the Hood Repair section for more de-
tails.
Fuel and Hydraulic Tanks Repair
INSPECT
Make a visual inspection of all sides of the tank. Inspect
the welds for cracks and leakage. Check for wet areas,
accumulation of dirt, and loose or missing paint caused
by leakage. Areas of the tank that are not easily seen
can be checked with an inspection mirror and a light that
is approved for locations with flammable vapors.
SMALL LEAKS, REPAIR
Use the following procedure to repair small leaks:
1. Use steam to clean the area around the leak. Re-
move all paint and dirt around the leak.
WARNING
Do not use tools that can make sparks, heat, or
static electricity. The vapors in the tank can cause
an explosion.
2. Apply Loctite®
290 to the leak. Follow the instruc-
tions of the manufacturer.
LARGE LEAKS, REPAIR
1. Use one of the procedures described under Clean
in this section to clean and prepare the tank for
repairs.
2. Use acceptable welding practices to repair the
tank. See the American National Standard Safety
In Welding and Cutting AWS Z 49.1 - 1999.
CLEAN
WARNING
Special procedures must be followed when large
leaks or other repairs need welding or cutting. All
work must be done by authorized personnel. If the
tank is cleaned inside a building, make sure there is
enough ventilation. See the following manuals for
additional information:
• Safe Practices for Welding and Cutting Con-
tainers That Have Held Combustibles, American
Welding Society, F4.1 - 1999.
• Safety In Welding and Cutting, American National
Standard, AWS Z 49.1 - 1999.
When cleaning the tank, do not use solutions that
make dangerous gases at normal temperatures or
when heated. Wear eye and face protection. Protect
the body from burns.
When cleaning with steam, use a hose with a minimum
diameter of 19 mm (0.75 in.). Control the pressure of
the steam by a valve installed at the nozzle of the hose.
If a metal nozzle is used, it must be made of a material
that does not make sparks. Make an electrical connec-
tion between the nozzle and the tank. Connect a ground
wire to the tank to prevent static electricity.
6
8. 100 YRM 449 Radiator Repair
Steam Method of Cleaning
Use the following procedure to clean the tank with
steam:
1. Remove all the parts from the tank. Install the drain
plug.
2. Fill the tank 1/4 full with a solution of water and
sodium bicarbonate or sodium carbonate. Mix
0.5 kg (1 lb) per 4 liter (1 gal) of water.
3. Mix the solution in the tank using air pressure.
Make sure all the surfaces on the inside of the tank
are flushed with the solution. Drain the tank.
4. Put steam into the tank until the tank does not have
odors and the metal is hot. Steam vapors must
come from all the openings.
5. Flush the inside of the tank with boiling water. Make
sure all the loose material is removed from the in-
side of the tank.
6. Make an inspection of the inside of the tank. If it
is not clean, repeat Step 4 and Step 5 and make
another inspection. When making inspections, use
a light that is approved for locations with flammable
vapors.
7. Put plugs in all the openings in the tank. Wait 15
minutes, then remove the inlet and outlet plugs.
Test a sample of the vapor with a special indicator
for gas vapors. If the amount of flammable vapors is
above the lower flammable limit, repeat the clean-
ing procedures.
Chemical Solution Method of Cleaning
If the tank cannot be cleaned with steam, use the fol-
lowing procedure:
1. Mix a solution of water and trisodium phosphate or
a cleaning compound with an alkali base. Follow
the instructions given by the manufacturer.
2. Fill the tank with the cleaning solution. Use com-
pressed air to mix the solution in the tank.
3. Drain the tank. Flush the inside of the tank with
hot (boiling) water. Make sure all the cleaning com-
pound is removed.
4. Make an inspection of the inside of the tank. If the
tank is not clean, repeat Step 1 through Step 3.
Make another inspection of the tank. When mak-
ing inspections, use a light that is approved for lo-
cations with flammable vapors.
5. Check the tank for flammable vapors using special
indicator for gas vapors. If the amount of flammable
vapors is not below the lower flammable limit, re-
peat the cleaning procedures.
ADDITIONAL PREPARATIONS FOR
REPAIR
If nitrogen gas or carbon dioxide gas is available, pre-
pare the tank for welding using these gases. See the
manual Safe Practices for Welding and Cutting Con-
tainers That Have Held Combustibles by the American
Welding Society, F4.1 - 1999. If these gases are not
available, another method using water can be used as
follows:
1. Fill the tank with water to just below the point where
the work will be done. Make sure the space above
the level of the water has a vent.
2. Use acceptable welding practices to repair the
tank. See the American National Standard Safety
In Welding and Cutting AWS Z 49.1 - 1999.
Radiator Repair
REMOVE
NOTE: To make radiator removal easier, remove the
counterweight as described in Counterweight Repair,
Remove.
1. Open the access door between the hood and the
counterweight. Remove the cover plate over the
radiator. If installed, remove the LPG tank and
bracket.
2. Drain the coolant from the radiator. Remove the ra-
diator hoses. Disconnect the oil lines at the radiator.
Put caps on the open lines.
3. Remove the remote fill assembly and radiator
hoses to the engine. Disconnect the hose to the
auxiliary coolant reservoir.
4. Remove the hood and transition plate as described
in Hood Repair, Remove. Remove the fan shroud
and fan. Loosen the exhaust band clamp on the
7
9. Exhaust System Repair 100 YRM 449
gasoline and LPG units. Remove the engine water
outlet on diesel units.
5. Remove the muffler and inlet exhaust pipe to the
muffler. Remove the capscrews that fasten the ra-
diator. Move the exhaust pipe for clearance of the
radiator flange.
6. Tip the radiator forward over the engine as you lift
and remove the radiator.
INSTALL
NOTE: The installation of the radiator is easier if the
counterweight is removed. See Counterweight Repair,
Remove in this section.
1. Tip the radiator forward over the engine as you in-
stall the radiator in the lift truck. Move the exhaust
pipe for clearance to the radiator flange.
2. Install the capscrews that fasten the radiator. Install
the muffler and inlet exhaust pipe at the muffler.
3. Install the engine water outlet on diesel units.
Tighten the exhaust band clamp on gasoline or
LPG units. Install the fan and fan shroud. Install
the hood and transition plate as described in the
Hood Repair, Install section.
4. Connect the hose to the auxiliary coolant reservoir.
Install the remote fill assembly and radiator hoses
to the engine. Make sure the hose clamp screws
have an access at the wheel wells.
5. Connect the oil lines at the radiator. Install the cover
plate over the radiator and fill the radiator with the
coolant specified in the table in the Periodic Main-
tenance 8000 YRM 393.
6. If removed, install the counterweight as described
in the Counterweight Repair, Install section. If the
LPG tank and bracket were removed, install them.
Exhaust System Repair
MUFFLER
Remove
1. Remove the grill by removing the retaining plate at
the top of the grill. See Figure 5, Figure 6, and
Figure 7.
2. Disconnect the exhaust pipes and remove the
clamps.
3. Remove the clamp from the muffler outlet and re-
move the muffler.
Install
1. On overhead exhaust units, install the counter-
weight exhaust pipe on the muffler, but do NOT
tighten. See Figure 5, Figure 6, and Figure 7..
2. Install the muffler and, on units with the overhead
exhaust, rotate the muffler so the outlet is at the
top. Install the other exhaust pipes and tighten the
clamps. Rotate the counterweight exhaust pipe so
that it points straight back and down at a 45 angle.
3. Install the grill and align the end of the counter-
weight exhaust pipe so that it is between the grill
bars.
Legend for Figure 5
1. COUNTERWEIGHT
2. GM-V6 ENGINE
3. PERKINS ENGINE
4. MUFFLER
5. CLAMP
6. EXHAUST PIPE
7. CROSSOVER PIPE
8. TAIL PIPE
9. BAND CLAMP
8
10. 100 YRM 449 Exhaust System Repair
Figure 5. Exhaust System
9
11. Exhaust System Repair 100 YRM 449
A. GAS/LPG COUNTERWEIGHT EXHAUST EPA
COMPLIANT
B. GAS/LPG COUNTERWEIGHT EXHAUST
NON-EPA COMPLIANT
1. UPPER EXHAUST PIPE
2. TAIL PIPE
3. COUNTERWEIGHT
4. MUFFLER
5. GASKET
6. LOWER EXHAUST PIPE
7. RAW GAS CHECK PORT
8. OXYGEN SENSOR PORT
9. CROSSOVER PIPE
10. FLEX PIPE
11. CLAMP
Figure 6. Exhaust System EPA Compliant Engine
10
13. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
14. Engine Repair 100 YRM 449
Engine Repair
REMOVE
NOTE: The lift truck can have a powershift or a man-
ual transmission. The powershift transmission and the
torque converter are attached to the engine. The en-
gine and powershift transmission are normally removed
as a unit. The manual transmission is attached to the
drive axle housing. This engine is removed without re-
moving the manual transmission.
1. Put the lift truck on blocks. See the Operating Man-
ual or the Periodic Maintenance 8000 YRM 393
for the correct procedures to put the lift truck on
blocks. Remove the overhead guard, hood, transi-
tion plate, and access door. See the Hood Repair,
Remove section for more details. Remove the floor
plates.
2. Disconnect the cables at the battery. Remove
the battery, air cleaner inlet duct, and battery tray.
Disconnect the brake fluid reservoir and engine
crankcase breather lines.
3. Remove the fan and fan shroud. Disconnect the
exhaust pipe at the exhaust headers.
4. Disconnect the fuel lines at the engine. Disconnect
the throttle linkage at the engine. Disconnect the
wires and wiring harnesses at the engine and pow-
ershift transmission.
5. Disconnect the oil lines at the hydraulic pumps.
Drain the hydraulic tank and put plugs in the open
ports. Disconnect the oil cooler lines from the pow-
ershift transmission.
6. Powershift transmission. Do the following proce-
dure:
a. Disconnect the linkage between the transmis-
sion and the pedals at the transmission.
b. Disconnect the hydraulic lines to the brake
booster.
c. Disconnect the brake line at the booster. Dis-
connect the electrical wiring.
d. Remove the pedal bracket.
e. On units without the Foot Directional Control
pedal, disconnect the direction control linkage
at the transmission.
f. Disconnect the drive line at the universal joint.
7. Manual transmission. Do the following procedure:
a. Disconnect the drive line at the universal joint
near the clutch.
b. Disconnect the hydraulic and brake lines. Dis-
connect the push rod to the brake booster. Dis-
connect the electrical wiring.
WARNING
Do NOT leave the clutch pedal free in the up position
with the over-center spring installed. The spring is
under tension and can cause an injury. Fasten the
clutch pedal so that it cannot move down, remove
the spring or carefully move the pedal to the down
position to remove the tension.
c. Remove the brake booster. Disconnect the
clutch push rod from the clutch cover.
8. Connect a lifting device to the engine. Make sure
the lifting device has a capacity of at least 450 kg
(1000 lb). Remove the four motor mount bolts.
Raise the engine from the frame. Be careful of the
hydraulic pump. Make sure that all wires and hoses
are disconnected. Put the engine in a position so
that it has stability and will not fall.
9. Remove the powershift transmission from the en-
gine as described in the Two-Speed Powershift
Transmission, Repairs 1300 YRM 325. On units
with the manual transmission, remove the oil clutch
housing and clutch cover from the engine.
INSTALL
1. Install the engine mounts on the engine as follows
(see Figure 8):
a. GM V-6: Tighten the capscrews that hold the
engine mount to the fan end of the engine to
30 N•m (22 lbf ft). Tighten the bolts that hold
the engine mounts to the mount plate to 65 N•m
(48 lbf ft).
b. PERKINS: Apply a sealant to the threads of the
capscrews and tighten the capscrews that hold
the engine mounts to the fan end of the engine
to 65 N•m (48 lbf ft).
12
15. 100 YRM 449 Engine Repair
A. FRONT MOUNTS
B. PERKINS, POWERSHIFT
C. GM-V6, POWERSHIFT ONLY
D. PERKINS, GM-V6 MANUAL ONLY
E. REAR MOUNTS
F. PERKINS
G. GM-V6
1. ENGINE OR TRANSMISSION MOUNT
2. ENGINE, TRANSMISSION, OR CLUTCH
HOUSING
3. MOUNT PLATE
4. BOLT
5. WASHER
6. RUBBER MOUNT
7. FRAME MOUNT WELDMENT
Figure 8. Engine Mounts
CAUTION
Apply a sealant (Yale Part Number 520042831) to
the flange of the flywheel housing. Make sure the
torque converter or clutch is installed correctly and
engaged with the oil pump. If the parts are not en-
gaged, the oil pump or torque converter will be dam-
aged.
2. If removed, install the torque converter and power-
shift transmission on the engine as described in the
Two-Speed Powershift Transmission, Repairs
1300 YRM 325. If removed, install the oil clutch
housing and cover on the engine.
3. Connect a lifting device to the engine. Make sure
the lifting device has a capacity of at least 450 kg
(1000 lb). Install the engine in the unit. Be careful
of the hydraulic pump. Make sure that all wires
and hoses are not damaged. Install the four motor
mount bolts. Connect all hoses and wiring. Make
13
16. Throttle Pedal Adjustment 100 YRM 449
sure the clamp screws for the radiator hoses are
aligned for access from the wheel wells.
4. Install the bolts for the engine mounts. See Fig-
ure 5. Tighten the bolts to 120 N•m (89 lbf ft).
5. Powershift transmission: do the following proce-
dure:
a. Connect the drive line at the universal joint.
b. On units without the Foot Directional Control
pedal, connect the direction control linkage at
the transmission.
c. Install the pedal bracket. Connect the brake
line at the booster.
d. Connect the hydraulic lines to the brake
booster.
e. Connect the linkage between the transmission
and the pedals at the transmission.
f. Connect the oil cooler lines for the transmis-
sion.
6. Manual transmission: do the following procedure:
a. Install the brake booster. Connect the clutch
push rod to the clutch cover.
b. Connect the hydraulic and brake lines. Con-
nect the push rod to the brake booster.
c. Connect the drive line at the universal joint near
the clutch.
7. Connect the oil lines at the hydraulic pumps. Fill the
hydraulic tank with the oil specified in the Periodic
Maintenance 8000 YRM 393.
8. Connect the fuel lines at the engine. Connect the
throttle linkage at the engine.
9. Connect the exhaust pipe at the exhaust header.
Install the fan and fan shroud.
10. Connect the engine crankcase breather and the
brake fluid reservoir lines. Install the battery tray,
air cleaner inlet duct, and battery. Connect the ca-
bles at the battery.
11. Install the floor plates. Install the overhead guard
and the hood, transition plate, and access door.
See Hood Repair, Install in this section. Remove
the blocks that support the lift truck using the re-
verse of the installation procedure in the section Pe-
riodic Maintenance 8000 YRM 393 or in the Op-
erating Manual.
12. Check all of the fluid levels and fill as necessary.
Remove the air from the brake system.
Throttle Pedal Adjustment
PERKINS 1104C-44(RE) DIESEL ENGINE
NOTE: The procedures below are for lift trucks
equipped with the Perkins 1104C-44(RE) Diesel
Engine. If your lift truck has either a gas or LPG en-
gine, see the section LPG Fuel System 900 YRM 348
for the procedures to adjust the throttle linkage.
1. Adjust the cable adjustment nuts to allow for a
3.0 mm (0.12 in.) maximum of free play on the
throttle cable length. See Figure 9. Secure cable
length by tightening cable lock nuts.
2. Set pedal stop to 35 ±2 mm (1.40 ±0.08 in.). Secure
in place with pedal stop jam nuts.
3. With the pedal against the stop, adjust the throttle
cable to ensure that the diesel injector pump is at
full power (the injection pump lever is touching the
lever stop in Figure 10).
4. Release the throttle pedal and adjust the up posi-
tion pedal stop until the tension is removed from the
cable when the injection pump lever is returned to
the idle position. Tighten up position pedal stop with
capscrew. See Figure 9.
14
17. 100 YRM 449 Throttle Pedal Adjustment
NOTE: THE FOOT DIRECTIONAL CONTROL PEDAL IS SHOWN. THE ADJUSTMENT PROCEDURES FOR THE
ACCELERATOR PEDAL ARE THE SAME.
1. MONOTROL PEDAL
2. DIESEL INJECTOR PUMP
3. CABLE ADJUSTMENT NUTS
4. CABLE LOCK NUTS
5. PEDAL STOP JAM NUTS
6. PEDAL STOP
7. UP POSITION PEDAL STOP
8. CAPSCREW
Figure 9. Foot Directional Control and Accelerator Pedal Adjustment
15
18. Safety Labels 100 YRM 449
Figure 10. Diesel Injector Pump
Legend for Figure 10
NOTE: DIESEL INJECTOR PUMP IS SHOWN IN THE
IDLE POSITION.
1. INJECTION PUMP LEVER
2. LEVER STOP
Safety Labels
WARNING
Safety labels are installed on the lift truck to give
information about operation and possible hazards.
It is important that all safety labels are installed on
the lift truck and can be read.
DO NOT add to or modify the lift truck. Any change
to the lift truck, the tires, or its equipment can
change the lifting capacity. The lift truck must be
rated as equipped and the nameplate must show
the new capacity rating. Contact your dealer for
Hyster lift trucks for a replacement nameplate.
If a label must be replaced, use the following procedure
to install a new label (see Figure 11):
WARNING
Cleaning solvents can be flammable and toxic and
can cause skin irritation. When using cleaning sol-
vents, always follow the recommendations of the
manufacturer.
1. Make sure the surface is dry and has no oil or
grease. Do not use solvent on new paint. Clean
the surface of old paint with a cleaning solvent.
2. Remove the paper from the back of the label. Do
not touch the adhesive surface.
3. Carefully hold the label in the correct position above
the surface. The label cannot be moved after it
touches the surface. Put the label on the surface.
Make sure that all air is removed from under the
label and the corners and edges are tight.
16