The document provides information on engine descriptions and service procedures for various components of DEUTZ and VOLVO diesel engines, including:
- The engines are four cylinder, four stroke engines with direct injection and turbocharging.
- Compression tests should yield results between 3-3.8 MPa across cylinders.
- The cylinder head is made of cast iron with vertical inlet and horizontal exhaust on the same side.
- Valves are adjusted using a rotation tool to specified clearances, checking with a feeler gauge.
- The timing gears are located at the flywheel end for the camshaft and power take-off, with stamped markings to set timing.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Volvo L40B Compact Wheel Loader Service Repair Manual Instant Download.pdf
1. Service Information
Document Title: Function Group: Information Type: Date:
Engine, description 200 Service Information 2014/3/10
Profile:
CWL, L40B [GB]
Engine, description
Machines of SN 1911001- / -1911499 and 1921001- / -1921499 are equipped with the DEUTZ-BF4M 1013 E engine.
Machines of SN 1911500- / -1913000 and 1921500- / -1923000 are equipped with the VOLVO-D5D engine.
Both engines are four cylinder, four stroke, in-line direct-injected diesel engines, with exhaust turbo and liquid cooling.
Machines fromSN 1913001- and 1923001- are equipped with the VOLVO-D5D engine.
he engine is a four-cylinder, four-stroke, in-line diesel engine with direct injection, exhaust turbocharger, liquid cooling and
internal, unregulated exhaust gas recirculation (EGR).
To comply with exhaust gas limit values, the turbocharger is equipped with unregulated, internal exhaust gas
recirculation (IEGR), which returns the exhaust gas within the cylinder head to the combustion air. The oxygen content of
this exhaust is low. A lower oxygen content reduces the temperature spike during combustion and thereby reduces nitrogen
oxide (NO ).
The camshaft has an extra cam - the trailing cam. This causes the inlet valve to briefly open during the exhaust stroke so that
exhaust gas also enters the engine intake system. In the subsequent induction stroke, this exhaust is sucked back in. There is
no regulation of exhaust gas quantity.
The engine data plate specifies model, engine number and power data. The engine number is also stamped into the
crankcase. Model and engine number must be specified when ordering spare parts. The direction of rotation is found on the
flywheel, anticlockwise. Firing order: 1-3-4-2 (cylinder no. 1 on the flywheel side).
IMPORTANT! Adjustments to the regulator may only be performed by trained staff in an authorized central repair
workshop.
Figure 1
Engine data plate
A.
B.
C.
D.
E.
F.
Engine type
Spare part number
Engine number
Capacity
Rated speed
Timing setting
Components, servicing view
4. Service Information
Document Title: Function Group: Information Type: Date:
Compression test 210 Service Information 2014/3/10
Profile:
CWL, L40B [GB]
Compression test
Op nbr 210-002
9998694 Adapter
9988539 Pressure gauge
9998007 Adapter
Injection valves are removed and valve clearance checked.
Remove injection valves, see 237 Injectors all, testing and adjusting incl removing and fitting
1.
Figure 1
Insert adapter (9998694) in injection valve bore with new seal ring.
2.
Figure 2
Place clamping claw on adapter. Tighten screw.
5. 3.
Figure 3
If necessary, screw on adapter 9998007 for the connector.
4. Connect compression tester 9988539. Crank engine with the starter.
5. Carry out compression test on each cylinder.
Compression: 3 +0.8 MPa (30 +8 bar) (435 +116 psi)
NOTE!
The compression measured depends on the starter rpm during the measurement and the engine's altitude.
Therefore, exact limit valuescannot be set. Compression measurement is recommended only for comparison of all
engine cylinders. If a deviation of more than 15% is found, the cylinder in question should be dismantled to
determine the cause.
6. Install compression tester and connector.
7. Install injection valves.
6. Service Information
Document Title: Function Group: Information Type: Date:
Cylinder head, description 211 Service Information 2014/3/10
Profile:
CWL, L40B [GB]
Cylinder head, description
The cylinder head is made of cast iron. The inlet air enters vertically (A) and the exhaust gases exit horizontally (B). Inlet and
exhaust are on the same side of the cylinder head.
Figure 1
Cylinder head
The cylinder head gasket is a multi-layer gasket with 1, 2 or 3 identification holes to indicate the three different thicknesses.
The choice of gasket thickness is determined by the piston protrusion over the cylinder head sealing surface. If new pistons
or a new cylinder block are fitted, the gasket thickness must be evaluated and changed if necessary.
Figure 2
Cylinder head gasket, marking
7. Service Information
Document Title: Function Group: Information Type: Date:
Valves, description 214 Service Information 2014/3/10
Profile:
CWL, L40B [GB]
Valves, description
The engines are equipped with one inlet and one exhaust valve per cylinder.
The upper area of the valve guide (on the valve stem) houses an O-ring (A). This O-ring seal should prevent a large level of
oil consumption and reduce the amount of hydrocarbons in the exhaust.
Valve rotation is achieved through the eccentric position of the rocker arm.
The valve springs have a prescribed direction of installation. The closely wound end of the valve spring must point toward
the cylinder head.
Rocker arm lubrication is a component of the centralized lubricating system. The oil is supplied via the tappets and push
rods.
Figure 1
Due to a new valve spring guide design, it is no longer possible to use a feeler gauge to adjust the valves of L40B machines
from SN 1913001 – / 1923001 – and L45B machines from SN 1943001 – / 1953001 –. For this reason, valve clearance
must be adjusted using the rotation angle disc.
Figure 2
Valve system
9. Service Information
Document Title: Function Group: Information Type: Date:
Valves, adjusting 214 Service Information 2014/3/10
Profile:
CWL, L40B [GB]CWL, L40B [GB]
Go back to Index Page
Valves, adjusting
Op nbr 214-012
885530 Rotation tool
NOTE!
Only adjust the valve clearance with cold engine.
1. Place the machine in service position.
2. Remove pressure control valve and valve cover.
Figure 1
Valve cover with pressure control valve
3. Remove retainer plate with cabling.
NOTICE
Valve adjustment with the engine running is not allowed since the valves may strike the piston, causing
severe damage.
Figure 2
1.
2.
Exhaust valves: 1, 3, 5, 7
Inlet valves: 2, 4, 6, 8
4. Rotate the engine until the valves on cylinder no. 1 stand at "valve overlap".
10. NOTE!
Valve overlap means: exhaust valve not yet closed, inlet valve begins to open.
Figure 3
5. Adjust the valves marked black in illustration.
Inlet valve: 0.3 mm (0.0118 in)
Exhaust valve: 0.5 mm (0.0197 in)
NOTE!
In case the cylinder head gasket has been replaced, increase valve clearance by 0.1 mm (0.0040 in) !
Figure 4
6. Tighten the lock nut to 20 ±2Nm (15 ±1.5 lbf ft). Check the valve clearance again with the feeler gauge.
Figure 5
7. Rotate the engine again, one full turn until the valves on cylinder 4 are at "valve overlap". Adjust the valve clearance
on valves marked black in the illustration.
11. Figure 6
8. Install the gasket, replace if necessary.
9. Attach the valve cover and retainer plate. Tightening torque 11 Nm (8.1 lb ft)
NOTE!
Ensure that the rubber seals for the fuel lines are fitted in the correct position during assembly.
Figure 7
1.
2.
Valve cover gasket
Rubber seal
10. Attach pressure control valve to valve cover. Tightening torque 8.5Nm (6.3 lb ft)
Figure 8
Valve cover with pressure control valve
12. Service Information
Document Title: Function Group: Information Type: Date:
Valves, adjusting 214 Service Information 2014/3/10
Profile:
CWL, L40B [GB]CWL, L40B [GB]
Go back to Index Page
Valves, adjusting
Op nbr 214-012
885530 Rotation tool
885812 Timing tool
NOTE!
Only adjust the valve clearance with cold engine.
1. Place the machine in service position.
2. Unscrew the bolts (1) and remove crankcase ventilation (2).
Figure 1
Crankcase ventilation channel
3. Remove the cover plate (1) with wiring.
Figure 2
4. Unscrew the cylinder head cover bolts and remove with gasket.
13. NOTICE
Valve adjustment with the engine running is not allowed since the valves may strike the piston, causing
severe damage.
Figure 3
1.
2.
Exhaust valves: (EX) 1, 3, 5, 7
Inlet valves: (IN) 2, 4, 6, 8
5. Rotate the engine until the valves on cylinder no. 1 stand at "valve overlap".
NOTE!
Valve overlap means: exhaust valve not yet closed, inlet valve begins to open.
Figure 4
IN = inlet vavle
EX = outlet valve
Adjust valve clearance in accordance with the black mark on the adjustment chart for each cylinder.
Inlet valve: (IN) 90°
Figure 5
Adjust inlet valve clearance
6. Undo the lock nut (1) and screw in the adjustment screw (2) until it makes contact.
14. Figure 6
NOTE!
The rocker arm must make contact (no gap) with the thrust washer (arrow) of the spring disc.
7. Position the rotation angle disc on the adjuster screw. Secure the magnet of the rotation angle disc to the cylinder
head. Set the rotation angle disc to "Null" in the direction of the arrow.
Figure 7
NOTE!
Take care not to turn the adjustment screw.
8. Turn the adjustment screw anticlockwise 90°.
Figure 8
9. Counterhold the adjustment screw and tighten the lock nut to 20 ± 2 Nm (14.8 ± 1.5 lbf ft). Remove the rotation
angle disc.
15. Figure 9
Adjust exhaust valve clearance
10. Rotate the engine one revolution again until the valves of cylinder no. 4 are at "valve overlap". Adjust valve
clearance in accordance with the black mark on the adjustment chart for each cylinder.
Exhaust valve: (EX)150°
NOTE!
Follow steps 6 to 9 for adjusting exhaust valve clearance.
Figure 10
11. Clean the sealing surfaces of the cylinder head.
12. Fit a new gasket to the cylinder head cover.
13. Fit the cylinder head cover and tighten the bolts alternately to 13 Nm (9.6 lbf ft).
14. Fit the cover plate (1) with wiring.
15. Fit the crankcase ventilation. Tighten the bolts to 20 ± 2 Nm (14.8 ± 1.5 lbf ft.
16. Start the engine and check for leaks and proper operation.
16. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
17. Service Information
Document Title: Function Group: Information Type: Date:
Engine timing gear,
description
215 Service Information 2014/3/10
Profile:
CWL, L40B [GB]
Engine timing gear, description
On the engines, the timing gears are located at the flywheel end for the camshaft and power take-off.
Stamped markings on the crankshaft and camshaft gears are used to facilitate correct setting.
Figure 1