Rohit Bedre is seeking a job that utilizes his theoretical knowledge of VLSI layout and design as well as his practical experience in RF and PCB design. He has over one year of experience in RF and PCB design. He has proficiency with Cadence, HFSS, AWR, and Altium Designer software. His education includes an M.Sc in Electronic Science from the University of Pune. Some of his projects include designing basic gates, a 4-bit binary counter, a differential amplifier, and a half/full adder using VLSI layout. He also has experience designing waveguides, filters, power combiners, and PCBs.
Hardware interfacing & Software development with Beagle Bone Black:
Précis: Interfacing the Analog pressure sensor with BBB via ADC of board and to display the pressure in PSI.
Designing the OP-amp circuit to convert the differential output to single ended output, designing inverters with BJT & MOSFET and understanding all features of Beagle Bone Black System On Chip.
Acessing the Data from the particular address from the ROM of Board.
Software part includes – enabling the on Board RTC via Netwok Transfer Protocol, Enabling and Testing GPIO & SPI, I2C ,UART Data Transfer Protocols using loop-back method, Communication with two CPUS, Cloning sample programs into the Board from Internet.
Hardware interfacing & Software development with Beagle Bone Black:
Précis: Interfacing the Analog pressure sensor with BBB via ADC of board and to display the pressure in PSI.
Designing the OP-amp circuit to convert the differential output to single ended output, designing inverters with BJT & MOSFET and understanding all features of Beagle Bone Black System On Chip.
Acessing the Data from the particular address from the ROM of Board.
Software part includes – enabling the on Board RTC via Netwok Transfer Protocol, Enabling and Testing GPIO & SPI, I2C ,UART Data Transfer Protocols using loop-back method, Communication with two CPUS, Cloning sample programs into the Board from Internet.
1. Rohit Bedre
______________________________________________________________________________
Name : Rohit R. Bedre
Mob. : +91 8237288754
Email : bedre.rohit@gmail.com
______________________________________________________________________________
Career Objective
I am a looking for job which complement my theoretical Knowledge of VLSI Layout and
designing, Embedded system designing with practical industrial experience by working on
technically challenging projects and new technologies.
Profile Summary and Experience
One year experience in RF and PCB Design at LNSB Technologies, Pune.
M.Sc (Electronic Science) from DOES, University of Pune.
Sound knowledge of Cadence virtuoso and NC launch software.
Sound knowledge of HFSS, AWR software.
Sound knowledge of Altium Designer software.
Proficiency in grasping new programming and technical concept quickly and utilizing them
In a productive manner.
Possess good interpersonal and analytical communication skill.
Technical Spectrum
Cadence (VLSI) Tool’s Cadence Virtuoso
Physical verification tool “Assura”
RF Tool’s HFSS, AWR.
Mechanical Tool’s AutoCAD.
Programming Languages C, VHDL, Verilog.
IDE Tools Altium Designer LT spice, Xilinx, Orcad,
PAD, Mentor Graphics- Questasim, LabView, Matlab.
Embedded Platforms. AVR, PIC microcontrollers.
2. Rohit Bedre
Education Qualification
Degree University / Board Year Grad / Division
M.Sc(Electronics
sci.)
University of pune 2012-14 C
B.Sc Dr. B.A.M.U 2009-12 First Division
H.S.C Aurangabad Board 2006-8 Pass
S.S.C Aurangabad Board 2006 First Division
Projects
VLSI layout and design Projects (180 nm Technology)
1. Design and Layout of basic gates, 4 – Bit Binary Counter
In This project designed 4 bit counter using JK master-slave flip flop, basic Gates and layout
routing.
2. Matching Technique
To Design and Layout Differential amplifier, Current mirror, Resistor, Capacitor using
Matching Techniques.
3. Design and Layout of Half Adder, Full Adder with standard Cell.
4. Design and Layout of Multiplexer, De multiplexer.
RF, Communication and PCB Design Project at LNSB Technologies Company
1. Staped Rigged WaveGuide
Design KA Band to F Band Staped riggedmWaveGuide and it’s matched with 50ohm
Impedance of Transmission Line using HFSS software.
2. Bandpass filter Design using micro-strip Technology.
To design Bandpass Filter for 25 to 70Ghz frequency range using AWR software.
3. Waveguide to coax Adaptor
The Waveguide to coax Adaptor Design for KA,W,V Band using HFSS software.
4. Wilkinson power combiners using micro-strip Technology
3. Rohit Bedre
To design High frequency 15 to 55Ghz and 50 to 110Ghz power combiner using AWR
software.
5. PCB Design
High speed and high frequency PCB design up to 10 layers using Altium Designer software.
Embedded Project
1. Design of controller for spin coating system
This project uses ATmega8 microcontroller for control and monitoring the spin coating
system to improve the wafer coating technology and display the all parameter.
2. PWM based light Intensity Controller
This project uses ATmega8 microcontroller for controlling the light intensity of LED array. It
has runtime intensity variation form 10% to 100%.
Extra-curricular activities & achievement
Intermediate Drawing examinations (school).
UGC career oriented program “Audio equipment maintenance” (B.Sc).
Successfully completed Computer Hard ware & Networking.
Personal Profile
Name : Rohit Rameshrao Bedre
Date of Birth : 08th Dec 1990
Sex : Male
Marital status : Single
Address : House no-9, Prashanti Nagar, Navha Road, Jalna. Dist- Jalna 431203
Residential Address : Old sangvi, Pune.