This document provides a repair manual for Swe140S, Swe145, Swe145L, Swe160, Swe160L, Swe200, and Swe200L trucks. It includes sections on general safety rules, operating principles, parameters, installation, troubleshooting, maintenance of various systems, optional equipment, disposal instructions, wiring diagrams, hydraulic schematics, required tools, service data, and technical specifications. The manual emphasizes that only trained personnel should perform repairs and maintenance, and outlines safety precautions related to electrical systems, lifting, modifications, and more.
John deere 230 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualfhsjejkdm
This technical manual provides specifications and information for servicing a John Deere 200 Sprayer Attachment. It includes sections on general specifications for the vehicle and sprayer components, repair information such as torque values, lubricant specifications, and locations for identification numbers. It also describes operational checkout procedures to test the sprayer system.
John deere 113 172 clipper service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, including engine details, fuel and oil requirements, ignition components, and dimensions for the different models. Safety guidelines are also outlined for operating the equipment safely.
John deere 110 g, 210g, 240g 260g trimmer clutters service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreach and kickback, and not modify machines without authorization.
John deere 230 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 cs chainsaws service repair manualfhsjejkdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualfhsjejkdm
This technical manual provides specifications and information for servicing a John Deere 200 Sprayer Attachment. It includes sections on general specifications for the vehicle and sprayer components, repair information such as torque values, lubricant specifications, and locations for identification numbers. It also describes operational checkout procedures to test the sprayer system.
John deere 113 172 clipper service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, including engine details, fuel and oil requirements, ignition components, and dimensions for the different models. Safety guidelines are also outlined for operating the equipment safely.
John deere 110 g, 210g, 240g 260g trimmer clutters service repair manualfhsjejkdm
The document provides specifications for small engines and equipment including blowers, hedge clippers, and trimmers made by John Deere, listing details like engine type, displacement, speed ranges, components, and dimensions for each model. Safety guidelines are also provided, advising users to keep others away from operating equipment, avoid overreach and kickback, and not modify machines without authorization.
John deere 54 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 51 & 246 rotary brooms service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission oils, and specifications for rotary mowers and snowblowers. The manual aims to ensure technicians have the correct information to service equipment properly and safely.
John deere 48, 450, 550 & 660 rotary tillers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48, 50, 54, 60, 72, 76, 160, 172, 261 & 272 rotary mowers serv...fhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and operational testing for the engine, fuel system, electrical system, power train, steering, brakes, mower deck, and other components. Safety messages are presented throughout and fastener torque specifications are provided. The manual is intended for experienced technicians and is part of John Deere's total product support program.
John deere 47, 59 & 359 snowblowers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 46, 49 & 50 snowthrowers service repair manualfhsjejkdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers sections like safety procedures, fluid handling, battery handling, and service procedures.
Clark gph 50 forklift service repair manualfhsjejkdm
This document provides guidance on planned maintenance procedures for lift trucks. It emphasizes the importance of routine inspections and lubrication for long life and trouble-free operation. The summary outlines key steps in the planned maintenance process, including:
1. Performing a visual inspection of the entire lift truck, checking for issues like leaks, loose fasteners, and worn/damaged components.
2. Using a planned maintenance report form to document inspections and any needed repairs.
3. Testing functions like the starting system, gauges, controls, brakes and steering to ensure proper operation.
4. Inspecting and lubricating specific components, like the engine, hydraulic and electrical systems, wheels/
Clark gp127 e forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark lift truck maintenance personnel. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Specific safety practices include properly jacking, blocking and lifting trucks, following electrical safety procedures, and ensuring only trained personnel conduct maintenance.
Clark gp127 forklift service repair manualfhsjejkdm
This document provides instructions and safety precautions for Clark industrial lift truck maintenance personnel. It outlines recommended safe maintenance practices including properly jacking, blocking and towing trucks. The document instructs technicians to only perform maintenance if trained and authorized, using manufacturer procedures and recommendations. Technicians are advised to take safety precautions such as wearing protective equipment, disconnecting power sources, and avoiding fire hazards.
Clark gex20 30 forklift service repair manualfhsjejkdm
The document provides instructions and safety information for maintaining industrial trucks. It discusses identifying and understanding safety signs, recommended safe maintenance practices, and general shop safety precautions. The safe maintenance practices section lists 20 points covering proper maintenance procedures, qualifications of maintenance personnel, personal protective equipment, safety checks, fuel and electrical system handling, inspection of truck components, and using proper replacement parts.
Clark gcs standard forklift service repair manualfhsjejkdm
- This document is a service manual intended for CLARK dealers providing maintenance and repair information for CLARK lift trucks.
- It contains general safety practices and precautions for working on lift trucks, identifying important safety signs and messages, and provides model identification information.
- Technicians are instructed to read all safety information and follow proper procedures to prevent injuries when servicing lift trucks.
Clark g127 e forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark industrial lift truck maintenance personnel. It outlines safe maintenance practices including lifting, jacking and blocking procedures. The document instructs technicians to only perform maintenance if properly trained, use personal protective equipment, disconnect power sources, and ventilate work areas. Technicians are advised to carefully read all procedures before starting any repair work.
Clark g127 forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark lift truck maintenance personnel. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Specific safety practices include properly jacking, blocking and lifting trucks, following electrical safety procedures, and ensuring only trained personnel conduct maintenance. The document emphasizes the importance of following manufacturer recommendations and guidelines to safely conduct maintenance and avoid injuries.
Clark ewp45 forklift service repair manualfhsjejkdm
This document provides instructions for performing planned maintenance on lift trucks. It discusses the purpose and terminology of periodic service and planned maintenance. Recommended maintenance intervals are based on normal, severe, or extreme operating conditions. A coding system is used on maintenance check sheets to indicate if components are OK, need minor adjustment, repair, or urgent repair. The document outlines steps for visual inspections of external components like batteries, covers, forks, and tires as well as operational tests of controls, brakes, and gauges.
Clark esm 25 forklift service repair manualfhsjejkdm
This document provides instructions for servicing the drive axle on an ESM-II truck model. It describes removing and replacing the drive axle, checking and changing the transmission fluid, and disassembling the drive axle. Special tools are required to remove some components like the pinion shaft lock nut and output shaft nut. The drive axle contains metric fasteners and components must be removed in a specified order.
Clark esm 12 forklift service repair manualfhsjejkdm
This document provides instructions for servicing the drive axle on an ESM-II truck model. It describes removing and replacing the drive axle, checking and changing the transmission fluid, and disassembling the drive axle. Special tools are required to remove some components like the pinion shaft lock nut and output shaft nut. The drive axle contains metric fasteners and components must be removed in a specified order.
Clark epg20 30 forklift service repair manualfhsjejkdm
Lifting, jacking, and blocking the truck must be done safely to prevent injury or equipment damage. The drive wheels must be raised using a hydraulic jack with safety stands. Working under a raised truck requires safety stands under the frame. The entire truck can be raised using an overhead hoist and slings under the frame. Shipping requires tie-down straps over major components.
Clark epg 15 18 forklift service repair manualfhsjejkdm
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Clark ecg20 32 forklift service repair manualfhsjejkdm
Lifting, jacking, and blocking the truck must be done safely to prevent injury or equipment damage. The drive wheels must be raised using a hydraulic jack with safety stands. Working under a raised truck requires safety stands under the frame. The entire truck can be raised using an overhead hoist and spreader bar attached to lifting lugs. Shipping requires tie-down straps over major components to secure the load.
John deere 54 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 51 & 246 rotary brooms service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission oils, and specifications for rotary mowers and snowblowers. The manual aims to ensure technicians have the correct information to service equipment properly and safely.
John deere 48, 450, 550 & 660 rotary tillers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48, 50, 54, 60, 72, 76, 160, 172, 261 & 272 rotary mowers serv...fhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48 inch commercial walk behind mower service repair manualfhsjejkdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and operational testing for the engine, fuel system, electrical system, power train, steering, brakes, mower deck, and other components. Safety messages are presented throughout and fastener torque specifications are provided. The manual is intended for experienced technicians and is part of John Deere's total product support program.
John deere 47, 59 & 359 snowblowers service repair manualfhsjejkdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 46, 49 & 50 snowthrowers service repair manualfhsjejkdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers sections like safety procedures, fluid handling, battery handling, and service procedures.
Clark gph 50 forklift service repair manualfhsjejkdm
This document provides guidance on planned maintenance procedures for lift trucks. It emphasizes the importance of routine inspections and lubrication for long life and trouble-free operation. The summary outlines key steps in the planned maintenance process, including:
1. Performing a visual inspection of the entire lift truck, checking for issues like leaks, loose fasteners, and worn/damaged components.
2. Using a planned maintenance report form to document inspections and any needed repairs.
3. Testing functions like the starting system, gauges, controls, brakes and steering to ensure proper operation.
4. Inspecting and lubricating specific components, like the engine, hydraulic and electrical systems, wheels/
Clark gp127 e forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark lift truck maintenance personnel. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Specific safety practices include properly jacking, blocking and lifting trucks, following electrical safety procedures, and ensuring only trained personnel conduct maintenance.
Clark gp127 forklift service repair manualfhsjejkdm
This document provides instructions and safety precautions for Clark industrial lift truck maintenance personnel. It outlines recommended safe maintenance practices including properly jacking, blocking and towing trucks. The document instructs technicians to only perform maintenance if trained and authorized, using manufacturer procedures and recommendations. Technicians are advised to take safety precautions such as wearing protective equipment, disconnecting power sources, and avoiding fire hazards.
Clark gex20 30 forklift service repair manualfhsjejkdm
The document provides instructions and safety information for maintaining industrial trucks. It discusses identifying and understanding safety signs, recommended safe maintenance practices, and general shop safety precautions. The safe maintenance practices section lists 20 points covering proper maintenance procedures, qualifications of maintenance personnel, personal protective equipment, safety checks, fuel and electrical system handling, inspection of truck components, and using proper replacement parts.
Clark gcs standard forklift service repair manualfhsjejkdm
- This document is a service manual intended for CLARK dealers providing maintenance and repair information for CLARK lift trucks.
- It contains general safety practices and precautions for working on lift trucks, identifying important safety signs and messages, and provides model identification information.
- Technicians are instructed to read all safety information and follow proper procedures to prevent injuries when servicing lift trucks.
Clark g127 e forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark industrial lift truck maintenance personnel. It outlines safe maintenance practices including lifting, jacking and blocking procedures. The document instructs technicians to only perform maintenance if properly trained, use personal protective equipment, disconnect power sources, and ventilate work areas. Technicians are advised to carefully read all procedures before starting any repair work.
Clark g127 forklift service repair manualfhsjejkdm
This document provides instructions and safety guidelines for Clark lift truck maintenance personnel. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Specific safety practices include properly jacking, blocking and lifting trucks, following electrical safety procedures, and ensuring only trained personnel conduct maintenance. The document emphasizes the importance of following manufacturer recommendations and guidelines to safely conduct maintenance and avoid injuries.
Clark ewp45 forklift service repair manualfhsjejkdm
This document provides instructions for performing planned maintenance on lift trucks. It discusses the purpose and terminology of periodic service and planned maintenance. Recommended maintenance intervals are based on normal, severe, or extreme operating conditions. A coding system is used on maintenance check sheets to indicate if components are OK, need minor adjustment, repair, or urgent repair. The document outlines steps for visual inspections of external components like batteries, covers, forks, and tires as well as operational tests of controls, brakes, and gauges.
Clark esm 25 forklift service repair manualfhsjejkdm
This document provides instructions for servicing the drive axle on an ESM-II truck model. It describes removing and replacing the drive axle, checking and changing the transmission fluid, and disassembling the drive axle. Special tools are required to remove some components like the pinion shaft lock nut and output shaft nut. The drive axle contains metric fasteners and components must be removed in a specified order.
Clark esm 12 forklift service repair manualfhsjejkdm
This document provides instructions for servicing the drive axle on an ESM-II truck model. It describes removing and replacing the drive axle, checking and changing the transmission fluid, and disassembling the drive axle. Special tools are required to remove some components like the pinion shaft lock nut and output shaft nut. The drive axle contains metric fasteners and components must be removed in a specified order.
Clark epg20 30 forklift service repair manualfhsjejkdm
Lifting, jacking, and blocking the truck must be done safely to prevent injury or equipment damage. The drive wheels must be raised using a hydraulic jack with safety stands. Working under a raised truck requires safety stands under the frame. The entire truck can be raised using an overhead hoist and slings under the frame. Shipping requires tie-down straps over major components.
Clark epg 15 18 forklift service repair manualfhsjejkdm
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Clark ecg20 32 forklift service repair manualfhsjejkdm
Lifting, jacking, and blocking the truck must be done safely to prevent injury or equipment damage. The drive wheels must be raised using a hydraulic jack with safety stands. Working under a raised truck requires safety stands under the frame. The entire truck can be raised using an overhead hoist and spreader bar attached to lifting lugs. Shipping requires tie-down straps over major components to secure the load.
Tanjore Painting: Rich Heritage and Intricate Craftsmanship | Cottage9Cottage9 Enterprises
Explore the exquisite art of Tanjore Painting, known for its vibrant colors, gold foil work, and traditional themes. Discover its cultural significance today!
The cherry: beauty, softness, its heart-shaped plastic has inspired artists since Antiquity. Cherries and strawberries were considered the fruits of paradise and thus represented the souls of men.
❼❷⓿❺❻❷❽❷❼❽ Dpboss Kalyan Satta Matka Guessing Matka Result Main Bazar chart Final Matka Satta Matta Matka 143 Kalyan Chart Satta fix Jodi Kalyan Final ank Matka Boss Satta 143 Matka 420 Golden Matka Final Satta Kalyan Penal Chart Dpboss 143 Guessing Kalyan Night Chart
2. Table of contents
Repair manual 7590354 en
General introduction 1
General safety rules 2
Operating principle 3
Parameters 4
Installation 5
6
Troubleshooting 7
Chassis C0000 8
Motors C1000 9
Transmission/Drive gear C2000 10
Brake/wheel/track system C3000 11
Steering system C4000 12
Electrical system C5000 13
Hydraulics/Pneumatics C6000 14
Work function - lifting masts C7000 15
Auxiliary equipment, installation equipment C8000 16
Optional equipment/Extra equipment C9000 17
Instructions for disposal 18
Wiring diagram 19
Hydraulics schematics 20
Tools 21
Service data and grease specifications 22
Technical data 23
24
3. General introduction 1
Repair manual 7590354-040
1.1 How to use this manual...................................................................................................................................... 1 - 1
1.2 Warning levels and symbols .............................................................................................................................. 1 - 1
1.3 Pictograms......................................................................................................................................................... 1 - 2
4. 1 General introduction
How to use this manual
1 - 1 Repair manual 7590354 en
1 General introduction1
General introduction
1.1 How to use this manual1.1
How to use this manual
The repair manual is divided into chapters containing the following information:
• General safety rules.
• Operating principle
This chapter provides a basic description of the main functions of the truck and their interdependencies.
• Parameters
This chapter provides a basic description of the truck parameters.
• Installation
This chapter describes the preparatory work that is to be done before the truck is used for the first time
• Maintenance
This chapter provides an overview of periodic maintenance.
• Troubleshooting
The chapter describes the action you should take when the truck is completely or partially out of function. It also
describes the cause of the problem together with suggested remedies.
• C codes
This chapter describes the various truck systems, e.g. the hydraulic system and includes descriptions of system
parts and the necessary service procedures. These descriptions are divided according to the manufacturer's C
code system.
• Instructions for disposal
This chapter specifies the proper sorting categories for the materials used in the various truck components.
• Wiring diagram
This chapter provides information on electrical components and wiring diagrams.
• Hydraulics schematics
This chapter provides information on hydraulic components and diagrams.
• Tools
This chapter provides a list of the special tools required.
• Service data and grease specifications
This chapter contains information on general tightening torques and specifications for lubricants.
• Technical data.
1.2 Warning levels and symbols1.2
Warning levels and symbols
The following warning levels and symbols are used in the repair manual:
DANGER
Indicates a dangerous situation that – if not avoided – will cause death or serious bodily injury.
WARNING
Indicates a dangerous situation that – if not avoided – could possibly cause death or serious bodily injury.
CAUTION
Indicates a dangerous situation that – if not avoided – will cause a slight or minor bodily injury.
NOTICE
Used in connection with actions that can cause material damage but not bodily injury.
Used to attract attention and to give information about various actions.
1
5. 1 General introduction
Pictograms
Repair manual 7590354 en 1 - 2
1.3 Pictograms1.3
Pictograms
Symbol Measure Symbol Measure
Visual inspection of condition, wear and loose
connections.
Component replacement.
Cleaning Measurement
Checks for leaks.
Check that bolts, nuts, etc. are tightened to
torque.
Listening for noise. Lubrication, application.
Check of functions. Calibration
Adjustment Welding
Disassembly/removal Assembly/installation
Open Close
Refilling Emptying
Update Charging
Lift Lowering
An example of another type of pictogram is “Cut cable ties”:
Additional information under the pictogram can, for example, indicate the number of cable ties to be cut.
7. 2 General safety rules
Authorised personnel
2 - 1 Repair manual 7590354 en
2 General safety rules2
General safety rules
2.1 Authorised personnel2.1
Authorised personnel
Only personnel trained in servicing and repair of this type of truck are authorised to carry out service and repair activities.
2.2 Work safety2.2
Work safety
For safe work with the truck, always remember:
▷ Always disconnect the battery when carrying out maintenance or repair work on the truck unless otherwise stated
in this repair manual.
▷ Make sure that the place where service work is performed is a safe place. Follow the regulations.
▷ Keep the maintenance work site clean. Oil and water on the floor will make it slippery.
▷ Use the correct working posture. Service work often involves sitting on your knees or bending over forwards. Try
sitting on a toolbox, for example, to relieve the strain on your knees and back.
▷ Loose items and jewellery can get caught in moving parts of the truck. So never wear loose articles or jewellery
while working on the truck.
▷ Exercise caution and always follow applicable local regulations when working at high heights.
▷ Use the correct tools for the work you are carrying out.
▷ Keep all tools well maintained.
▷ Make sure that all safety equipment including guards and covers are properly secured and that they work as in-
tended before starting the repair work. If a guard or cover must be removed in order to perform the repair work,
extra care must be taken, and when the repair work is finished the guard or cover must be refitted.
▷ Use paper or a stiff piece of cardboard when checking for possible oil leaks. Do not use your hands.
▷ The drive unit oil may be hot.
▷ Use only new and clean oil for the drive gear.
▷ Store and transport changed oil according to applicable local directions.
▷ Do not flush solvents, etc. down the drain unless they are intended to be disposed of in this way. Follow local dis-
posal regulations.
▷ Disconnect the battery prior to performing any welding work on the truck.
▷ Prior to welding or grinding on painted surfaces, be sure to remove the paint at least 100 mm around the welding/
grinding area by using sandblasting equipment or paint remover.
▷ To maintain a high level of truck safety and to minimise downtime, all current maintenance instructions must be
carried out.
▷ Always keep fire-fighting equipment close at hand, and do not use an open fire to check fluid levels or when
searching for leaks
2.3 Electrical system2.3
Electrical system
When working on the electrical system of the truck, remember the following:
2
8. 2 General safety rules
Electrical system
Repair manual 7590354 en 2 - 2
▷ Never wear loose items or jewellery when working with the truck.
WARNING Short-circuiting/Burn injuries
Short circuits and burn injuries can occur if metal objects come into contact with live electrical connections
when working on the truck's electrical system.
► Remove any jewellery and loose items before starting work on the truck.
▷ Always use insulated tools when working on the electrical system.
▷ Always disconnect the battery before opening any covers to drive units or the electrical system.
▷ Always disconnect the battery prior to welding work using an electric welding unit. The welding current may dam-
age the battery.
▷ Never remove the warranty seals on the electronic cards.
2.3.1 Electrostatic risks2.3.1
Electrostatic risks
Purpose
These work instructions describe how to work in a safe manner with components that are sensitive to electrostatic
chocks.
Scope
These work instructions apply to all that work with component or units that are sensitive to electrostatic chocks.
Procedure
Electrostatic discharges from people may destroy sensitive equipment. For this reason, one must follow the instructions
for packaging and earthing. Always pay attention to these precautionary instructions.
Electronic card are supplied in electrostatically protected packages or envelopes.
These packages carry the following symbol:
▷ Leave electrostatically sensitive equipment in their respective packaging until you can place them on an electro-
statically protected work area.
▷ Electrostatically sensitive equipment should only be handled when they are properly earthed.
▷ Use electrostatically protected footwear!
▷ Store electrostatically sensitive equipment in their protective packaging or on electrostatically protected surfaces.
▷ Use an antistatic surface:
2.3.2 Battery handling2.3.2
Battery handling
Working with and charging batteries should always be performed in accordance with the safety instructions provided by
the battery manufacturer.
• Always use safety equipment to protect the eyes, face and skin while checking or handling batteries.
• Do not place any electrically conductive items on the battery terminals or their connections.
• Ensure there is a shower and an eye bath nearby in case an accident happens.
• Batteries generate explosive gases. Never use an open flame or other sources of ignition in close vicinity to a battery.
9. 2 General safety rules
Safe lifting
2 - 3 Repair manual 7590354 en
• Do not place tools or other metal objects on the battery. This can cause a short-circuit and even an explosion.
• The battery must be used according to the battery manufacturer's instructions regarding ambient and working temperat-
ures. Otherwise there is a large risk that the battery is damaged and that it will soon have to be replaced.
• Spilled electrolyte must be neutralised at once using a lot of water.
NOTICE Changing to the correct battery type
Only change to a battery that complies with the data given on the truck identification plate. The weight of the battery af-
fects the stability and braking capacity of the truck. Information on the minimum permitted battery weight is on the truck
identification plate.
WARNING Risk of centre of gravity shifting
Battery weight that is too low results in a deterioration in stability and braking capacity.
► The battery weight must conform to the details specified on the truck identification plate.
WARNING Battery acid may cause burns
Battery acid may cause burns.
► If battery acid gets onto your skin or clothes, flush immediately with cold water.
► If you get battery acid in the face or in the eyes, immediately flush the area with cold water and seek medical as-
sistance.
2.4 Safe lifting2.4
Safe lifting
All lifting must be carried out on a level, non-slip and stable surface. Asphalt surfaces should be avoided if possible.
To prevent the truck moving while it is being lifted, it must not be lifted with anyone on the platform or with the tiller arm in
the lowered position.
If the drive wheel, which is braked, is being lifted the other wheels must be chocked to stop the truck from moving.
Select the lifting point so that the lift is as light as possible, for example one corner at a time. If the truck has marked lift-
ing points on the lower part of the chassis, these must be used to ensure balanced lifting.
Make sure the surface where the jack is placed is clean and free of oil and grease.
Make sure your hands and the jack lever are free of grease and oil.
Only use the lever supplied with the jack. If the lever is too short, more exertion than is necessary will be required. If the
lever is too long, there is a risk that the jack will be overloaded.
Never work under a truck that is not supported by trestles and secured by a lifting device.
Support the truck:
▷ as close to the lifted part of the chassis as possible in order to reduce the falling height if the truck should col-
lapse
▷ so the truck cannot move.
Never support the jack on trestles to achieve a higher lift.
Never work under a raised truck without it being properly supported on trestles.
2.5 Truck modifications2.5
Truck modifications
Any modification of the truck must be approved beforehand. No modification of truck may be performed that may influ-
ence the capacity, stability and safety of the truck without prior written approval from the manufacturer, its representative
or successor.
In the case of the manufacturer no longer being in business and there being no successor, the user of the truck may ar-
range for modifications on the precondition that the user:
▷ makes sure that an engineer with expert knowledge of industrial trucks and their safety designs, tests and imple-
ments the modification,
2
10. 2 General safety rules
Software
Repair manual 7590354 en 2 - 4
▷ files all documentation of the designs, tests and implementation of the modification,
▷ approves and makes the applicable changes to the capacity plate, adhesive labels, markings and operator’s
manual,
▷ affixes a permanent and well visible sign to the truck stating how the truck has been modified, together with the
date of the modification and the name and address of the company that carried out the modification work.
2.6 Software2.6
Software
Erroneous handling of the truck systems and/or the external systems of the truck may affect the safety of the truck and
the environment.
• Always make sure that the correct software is downloaded to the truck.
• In case of parameter adjustments, the recommended values must be respected.
• Only adjust one parameter at the time when performing changes to the truck. Check the function after each adjustment.
• Change the parameters in small increments.
2.7 Hydraulic system2.7
Hydraulic system
When working on the hydraulic system of the truck, remember the following:
▷ Lower the forks completely and keep pressing the button for another 5 - 10 seconds to relieve system pressure.
▷ The hydraulic oil may be hot.
▷ Only fill the hydraulic system with new and clean oil.
11. Operating principle 3
Repair manual 7590354-040
3.1 Description......................................................................................................................................................... 3 - 1
3.1.1 Battery is connected ............................................................................................................................ 3 - 1
3.1.2 Login via keypad.................................................................................................................................. 3 - 1
3.1.3 Login via “ID key” option...................................................................................................................... 3 - 1
3.1.4 Tiller arm lowered for driving ............................................................................................................... 3 - 2
3.1.5 Driving in fork direction ........................................................................................................................ 3 - 2
3.1.6 Driving in the drive wheel direction...................................................................................................... 3 - 2
3.1.7 Braking in neutral................................................................................................................................. 3 - 2
3.1.8 Reverse braking .................................................................................................................................. 3 - 3
3.1.9 Mechanical braking.............................................................................................................................. 3 - 3
3.1.10 Emergency reversal............................................................................................................................. 3 - 3
3.1.11 Fork lowering ....................................................................................................................................... 3 - 4
12. 3 Operating principle
Description
3 - 1 Repair manual 7590354 en
3 Operating principle3
Operating principle
3.1 Description3.1
Description
The Operating principle section provides a general description on how truck functions work and how they are interde-
pendent.
Because the control structure of the truck is so complex, it is not possible to describe all combinations. Similarly, it is not
possible to describe all influencing factors. Only a selection of such factors are indicated. A good aid is found in the de-
scriptive sections of the repair manual and in the parameter descriptions in particular.
3.1.1 Battery is connected3.1.1
Battery is connected
Event: 1 Battery is connected
Previous event -
Action(s) Battery [G1], page 19 - 2is connected
Influencing elements Main fuse OK
Power circuit fuse [F50], page 19 - 2[F51], page 19 - 2[F52], page 19 - 2 OK
Resulting conditions Login possible
3.1.2 Login via keypad3.1.2
Login via keypad
Event: 2 Login via keypad
Previous event Battery is connected, page 3 - 1
Action(s) Log in with a PIN code and press the ON button [S223], page 19 - 3
Influencing elements Emergency stop Nödstopp not activated
Drive mode sensor [B60], page 19 - 2 deactivated
Input T1:INP TILL. ARM IN DRIV. POS is {low}
Resulting conditions Battery indicator lamp is lit. The display [P6], page 19 - 3 shows the hour counter
for 5 seconds, followed by battery status (% of full charge)
The mechanical brake must remain actuated
T1:OUT.BRAKE RELEASE {high}
3.1.3 Login via “ID key” option3.1.3
Login via “ID key” option
Event: 3 Login via “ID key” option
Previous event Battery is connected, page 3 - 1
Action(s) Log in with an ID key and press the ON button [S223], page 19 - 3
Influencing elements Emergency stop Nödstopp not activated
Drive mode sensor [B60], page 19 - 2 deactivated
Input T1:INP TILL. ARM IN DRIV. POS is {low}
Resulting conditions Battery indicator lamp is lit. The display [P6], page 19 - 3 shows the hour counter
for 5 seconds, followed by battery status (% of full charge)
The mechanical brake must remain actuated
T1:OUT.BRAKE RELEASE {high}
3
13. 3 Operating principle
Description
Repair manual 7590354 en 3 - 2
3.1.4 Tiller arm lowered for driving3.1.4
Tiller arm lowered for driving
Event: 4 Tiller arm lowered for driving
Previous event Login via keypad, page 3 - 1
Login via “ID key” option, page 3 - 1
Action(s) Lower tiller arm
Influencing elements Sensor [B60], page 19 - 2 for tiller arm in drive mode
Resulting conditions Sensor [B60], page 19 - 2 for tiller arm in drive mode activated T1:INP.TILLER
ARM IN DRIVE POS {high}
Main contactor output goes {low} T1:OUT.MAIN CONTACTOR.
Main contactor closes
3.1.5 Driving in fork direction3.1.5
Driving in fork direction
Event: 5 Driving in fork direction
Previous event Tiller arm lowered for driving, page 3 - 2
Action(s) Move the speed control [L1] in the fork direction
Influencing elements Hall element in speed control [A5:S310-S318]
Parameter settings
Resulting conditions T1:OUT.BRAKE RELEASE goes {low}
Brake coil is energised, mechanical brake is released
Pulsed current is fed to the drive motor in proportion to the position of the speed
control
3.1.6 Driving in the drive wheel direction3.1.6
Driving in the drive wheel direction
Event: 6 Driving in the drive wheel direction
Previous event Tiller arm lowered for driving, page 3 - 2
Action(s) Move the speed control [L1] in the drive wheel direction
Influencing elements Direction indicator's Hall element [A5:S300-S308]
Parameter settings
Resulting conditions T1:OUT.BRAKE RELEASE goes {low}
Brake coil is energised, mechanical brake released
Pulsed current is fed to the drive motor proportionally to the position of the speed
control [L1]
3.1.7 Braking in neutral3.1.7
Braking in neutral
Event: 7 Braking in neutral
Previous event Driving in fork direction, page 3 - 2
Driving in the drive wheel direction, page 3 - 2
Action(s) Allow the speed control [L1] to return to the neutral position
Influencing elements Parameter settings4, page 4 - 2
14. 3 Operating principle
Description
3 - 3 Repair manual 7590354 en
Event: 7 Braking in neutral
Resulting conditions The drive motor works as a generator and converts the kinetic energy of the truck
into electrical energy via the transistor regulator [T1], page 19 - 4. This reduces
the speed of the truck.
The excess energy is fed back to the battery [G1], page 19 - 2
The mechanical brake is activated when the truck comes to a complete stop
T1:OUT.BRAKE RELEASE goes {high}
3.1.8 Reverse braking3.1.8
Reverse braking
Event: 8 Reverse braking
Previous event Driving in fork direction, page 3 - 2
Driving in the drive wheel direction, page 3 - 2
Action(s) The speed control [L1] is moved to the opposite driving direction
Influencing elements Parameter settings201, page 4 - 5
Resulting conditions The drive motor works as a generator and converts the kinetic energy of the truck
into electrical energy via the transistor regulator [T1], page 19 - 4. This reduces
the speed of the truck.
The excess energy is fed back to the battery [G1], page 19 - 2
The mechanical brake is activated when the truck comes to a complete stop
T1:OUT.BRAKE RELEASE goes {high}
3.1.9 Mechanical braking3.1.9
Mechanical braking
Event: 9 Mechanical braking
Previous event Driving in fork direction, page 3 - 2
Driving in the drive wheel direction, page 3 - 2
Action(s) Raise or lower the tiller arm
Influencing elements Sensor [B60], page 19 - 2 for tiller arm in drive mode
Resulting conditions Input T1:INP TILL. ARM IN DRIV. POS goes {low}
Brake reduction until the truck is stationary
Brake coil is deactivated, mechanical brake is applied
T1:OUT.BRAKE RELEASE goes {high}
3.1.10 Emergency reversal3.1.10
Emergency reversal
Event: 10 Emergency reversal
Previous event Driving in the drive wheel direction, page 3 - 2
Action(s) When driving in the drive wheel direction, the emergency reversal button is
pressed
Influencing elements Emergency reversal
Resulting conditions The Hall sensor [A5:S317] is immediately activated. The card [A5], page 19 - 1
interprets this signal as a command to the transistor regulator [T1], page 19 - 4 to
run the drive motor at a reduced speed in the fork direction as long as the button is
pressed. The normal drive command signal received from [L1] is blocked until [L1]
is released and returns to neutral position.
3
17. 4 Parameters
Display/change parameters
4 - 1 Repair manual 7590354 en
4 Parameters4
Parameters
4.1 Display/change parameters4.1
Display/change parameters
CAN key 7516708, page - 000
1. Ensure that the truck is switched off. Connect the CAN key or enter the PIN code.
Do not press the ON switch.
Before any service parameter can be changed, the CAN service key must be connected to the contact [X41].
2. Press and then release the horn button. “Info“ is shown on the display.
3. Move between menus by turning the speed control several times.
4. “Par” is shown on the display.
5. Press the horn button to select. The parameter symbol lights up.
6. You move along in the parameter list by pressing the speed control repeatedly.
To show a parameter, release the speed control when the required parameter is shown on the display. Press the horn
button to change the parameter.
4.2 Parameters in general4.2
Parameters in general
The truck's control system can store a number of different parameters. These are used to configure the truck according
to the task to be performed. The parameters are divided into groups:
- Operator parameters – The driver parameters (range 1-100) are used to adapt the truck’s characteristics to a specific
driver or task. Up to 10 operator parameter profiles can be stored.
- Service parameters – The service parameters (range 101–1000) are used to adapt the truck's performance/response
and include all other parameters not among the operator parameters.
- Factory parameters – (range 1001-1250). Truck-specific parameters.
- Calibration parameters – (range 1251-1300) store the value generated on the calibration of valves, weight indication,
etc. These must not be changed manually.
Operator parameters are displayed and changed only for a selected operator, but if a CAN service key is connected, the
parameters for all operators can be displayed and changed. Operator parameters can be changed by the operator if the
truck's program is set up for this.
The service parameters can be changed once a suitable CAN service key or PDA/PC has been connected to the truck.
Factory parameters can only be changed using the TruckCom software application.
4
18. 4 Parameters
Parameter list
Repair manual 7590354 en 4 - 2
4.3 Parameter list4.3
Parameter list
4.4 Parameter list4.4
Parameter list
Software: 7528678
4.4.1 Operator parameters
No. Parameter type Min Std. Max Step Unit
1 Max. speed, in fork direction 30 100 100 5 %
2 Maximum speed, in drive wheel direction 30 100 100 5 %
3 Acceleration 10 100 100 5 %
4 Automatic speed reduction 40 100 100 5 %
5 Maximum speed, gates are down 30 100 100 5 %
6 Max. speed, walk-along mode 30 100 100 5 %
7 Maximum speed, forks above 1.8 m 30 100 100 5 %
Overview
Par. Description
1 Max. speed in fork direction
2 Maximum speed in drive wheel direction
3 Acceleration
4 Deceleration
5 Maximum speed, platform loaded, safety gate lowered
6 Maximum speed, platform not loaded
7 Maximum speed, forks above 1.8 m
The operator parameters can be adjusted individually to the available log-in profiles. The parameter’s connection to the
operator is done by a combination of operator and parameter numbers where the single digit always corresponds to the
parameter.
Operator profile Parameter range
1 1-7
2 11-17
3 21-27
4 31-37
5 41-47
6 51-57
7 61-67
8 71-77
9 81-87
10 91-97
Tab. 1: Connection to logged-in operator
19. 4 Parameters
Parameter list
4 - 3 Repair manual 7590354 en
4.4.1.1 Maximum travel speed
No. Parameter type Min Std. Max Step Unit
1 Max. speed, in fork direction 30 100 100 5 %
2 Maximum speed, in drive wheel direction 30 100 100 5 %
5 Maximum speed, gates are down 30 100 100 5 %
6 Max. speed, walk-along mode 30 100 100 5 %
7 Maximum speed, forks above 1.8 m 30 100 100 5 %
These parameters are used to limit the maximum travel speed for the operator profile that is logged on.
The maximum travel speed can also be limited by factory parameter 1044, page 4 - 22 and it is always the lowest speed
for a parameter that is the limiting one.
Maximum travel speed" forks above 1.8 m is set as a % of the value of service parameter 203, page 4 - 5
1 Max. speed, in fork direction
No. Parameter type Min Std. Max Step Unit
1 Max. speed, in fork direction 30 100 100 5 %
Adjusts the maximum speed of the truck in the fork wheel direction, with gates up and operator on the platform
2 Maximum speed, in drive wheel direction
No. Parameter type Min Std. Max Step Unit
2 Maximum speed, in drive wheel direction 30 100 100 5 %
Adjusts the maximum speed of the truck in the drive wheel direction, with gates up and operator on the platform
5 Maximum speed, gates are down
No. Parameter type Min Std. Max Step Unit
5 Maximum speed, gates are down 30 100 100 5 %
Adjusts the maximum speed of the truck for this application, with gates down and operator on the platform
6 Max. speed, walk-along mode
No. Parameter type Min Std. Max Step Unit
6 Max. speed, walk-along mode 30 100 100 5 %
Adjusts the truck’s maximum speed when the operator is not on the platform, platform is up and the gates down, i.e.
when the operator walks alongside the truck.
7 Maximum speed, forks above 1.8 m
No. Parameter type Min Std. Max Step Unit
7 Maximum speed, forks above 1.8 m 30 100 100 5 %
Adjusts the maximum speed of the truck when the forks are above 1.8 m
4
20. 4 Parameters
Parameter list
Repair manual 7590354 en 4 - 4
4.4.1.2 Acceleration/Deceleration
No. Parameter type Min Std. Max Step Unit
3 Acceleration 10 100 100 5 %
4 Automatic speed reduction 40 100 100 5 %
3 Acceleration
No. Parameter type Min Std. Max Step Unit
3 Acceleration 10 100 100 5 %
The lower the parameter value, the more time is needed to accelerate to the maximum speed.
4 Automatic speed reduction
No. Parameter type Min Std. Max Step Unit
4 Automatic speed reduction 40 100 100 5 %
Defines plug braking force when the operating control [L1] returns to the neutral position. The lower the value of para-
meter, the longer it takes to reduce speed.
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. 4 Parameters
Parameter list
4 - 5 Repair manual 7590354 en
4.4.2 Service
No. Parameter type Min Std. Max Step Unit
101 Service intervals 0 0 2000 50 h
102 Operator access 1 3 10 1
103 Start-up display 1 2 5 1
104 Time to automatic log-out 0 20 20 1 min.
105 Collision sensor sensitivity in X 0 0 100 1
106 Collision sensor sensitivity in Y 0 0 100 1
107 Battery size 1 12 27 1
109 Battery type, built-in charger 0 0 3 1
110 Battery size, built-in charger 100 100 350 1 Ah
111 Resetting procedure after collision 0 0 3 1
112 Erase application data 0 0 2 1
201 Deceleration when reversing 70 100 100 5 %
202 Maximum speed Turtle mode activated 0.5 4.0 6.0 0.5 km/h
203 Maximum speed, forks above 1.8 m 0.5 6.0 6.0 0.5 km/h
204 Maximum acceleration, forks above 1.8 m 10 50 60 5 %
205 Maximum reversing, forks above 1.8 m 45 80 80 5 %
206 Automatic speed reduction, forks above 1.8 m 45 60 80 5 %
207 Deactivate the possibility to control the truck when walking
alongside it.
0 0 1 1
208 Reduction of maximum speed with support arms fully lowered 0.5 12.5 12.5 0.5 km/h
208 Reduction of max. speed with forks fully lowered 0.5 12.5 12.5 0.5 km/h
209 Minimum fork/support arm lifting height to exit reduced speed
set with parameter 208
10 10 50 1 ms
211 Automatic speed reduction (Built-in) 25 25 100 5 %
220 Min. steering angle for initiation of speed limitation 1 5 10 1 °
222 Max. speed at full speed limitation 2.5 See the
table
6.3 1 km/h
223 Max. steering angle for full speed limitation 30 60 75 1 °
250 Min. steering resistance (TFD) in drive wheel direction 0 20 100 5 %
251 Max. steering resistance (TFD) in drive wheel direction 0 100 100 5 %
252 Min. steering resistance (TFD) in fork direction 0 20 100 5 %
253 Max. steering resistance (TFD) in fork direction 0 100 100 5 %
304 Support arm lowering speed 10 45 60 5 %
307 Automatic support arm lowering (On/Off) 0 2 3 1
311 Load weight 0 0 1 1 Kg
312 Pressure equalization 0 0 5 1 ms
313 Support arm lift speed 10 40 40 5 %
314 Deactivate lifting above 1.8 m 0 0 1 1
499 License key
4
23. 4 Parameters
Parameter list
Repair manual 7590354 en 4 - 6
Before any service parameter can be changed, the CAN service key must be connected to the contact [X41].
Changing specific truck parameters changes the truck's driving properties. Do not change any parameter values without
the necessary know-how.
Par. Description
101 Service intervals
102 Operator access
103 Start-up - alternative
104 Automatic logout/min
105 Collision sensor X-level
106 Collision sensor Y-level
107 Battery adjustment, Ah
109 Battery type, built-in charger
110 Battery size, built-in charger
111 Reset following a collision
112 Clear application data
4.4.2.1 General service parameters
No. Parameter type Min Std. Max Step Unit
101 Service intervals 0 0 2000 50 h
102 Operator access 1 3 10 1
103 Start-up display 1 2 5 1
104 Time to automatic log-out 0 20 20 1 min.
105 Collision sensor sensitivity in X 0 0 100 1
106 Collision sensor sensitivity in Y 0 0 100 1
107 Battery size 1 12 27 1
109 Battery type, built-in charger 0 0 3 1
110 Battery size, built-in charger 100 100 350 1 Ah
111 Resetting procedure after collision 0 0 3 1
112 Erase application data 0 0 2 1
102 Operator access
No. Parameter type Min Std. Max Step Unit
102 Operator access 1 3 10 1
Specifies which login method should be used and if the operator will have the possibility of changing the operator para-
meter settings.
Values 1 and 2 = Key
Values 3 and 4 = Keypad with up to 100 PIN codes.
Values 5 and 6 = Keypad with DHU
Values 7 and 8 = ID unit
Values 9 and 10 = SA2
Odd values = Operator parameters are open and can be changed by the operator.
Even values = Operator parameters can only be changed with a CAN key connected.
24. 4 Parameters
Parameter list
4 - 7 Repair manual 7590354 en
103 Start-up display
No. Parameter type Min Std. Max Step Unit
103 Start-up display 1 2 5 1
Sets which value is shown on the display when the truck is started.
When the truck is started, one of the truck's 5 values is shown on the hour meter display "H" (hour meter display) for 5
seconds. After the menu has disappeared, the battery capacity is continuously shown in the numeric field at the same
time as the battery indicator is lit.
The truck control system stores five different time values. "Value 2 - Operating time" is the default value on the start-up
display.
Hour meter values Display
Value 1 = (A) Key time
The total time the truck has been in use.
Value 2 = (B) Operating time
Combined time during which the pump or drive motor
has been in operation. Default display.
Value 3 = (C) Drive motor time
The total time the drive motor has been in operation.
Value 4 = (D) Pump motor time
Total time the pump motor has been in operation.
Value 5 = (S) Remaining time until next service.
Parameter 101 controls the initial value.
4.4.2.1.1 Service/log-out
No. Parameter type Min Std. Max Step Unit
101 Service intervals 0 0 2000 50 h
104 Time to automatic log-out 0 20 20 1 min.
101 Service intervals
No. Parameter type Min Std. Max Step Unit
101 Service intervals 0 0 2000 50 h
This parameter determines the time value (in hours) to the next service from 0 to 2000 hours in increments of 50 hours.
Whenever this value is changed, the timer is reset and will start to count the truck activity time. On reaching the set
value, code “S - 0h” is shown on the display and the red LED flashes.
If the value is set as '0', no service interval is given.
104 Time to automatic log-out
No. Parameter type Min Std. Max Step Unit
104 Time to automatic log-out 0 20 20 1 min.
Gives the time, in minutes, before automatic log-out if the truck is inactive.
If the value is set as ‘0’, logout takes place after 4 hours.
4