Tank level to base radio and hmi
•
0 likes•130 views
The Digital Level Transmitter on top of the tank wirelessly transmits tank product level data to the Base Unit. The Base Unit uses Modbus RTU communications to display the tank level on its 4-inch touch screen display. The Base Unit is powered by a 12 VDC power supply and communicates with the transmitter via an RS 485 Modbus connection.
Report
Share
Report
Share
Download to read offline
Recommended
Hyrostatic to base unit and generic hmi
The document describes a digital level transmitter system that uses a transmitter on top of a tank to wirelessly transmit fluid head pressure data to a base unit. The base unit then displays the tank fluid head pressure on a 4-inch touch screen display using Modbus RTU communications. The system includes components like an enclosure, display, antenna, and power supplies.
Tank point and continuous level to base radio and back haul
The document describes a wireless tank level monitoring system. A discrete or digital level transmitter on the tank transmits the local tank level data to a base unit display within 3000 feet. The base unit then transmits the tank level data to a field office using long haul radios for monitoring on a touch screen display.
Transponder
A transponder is a device on a satellite that receives transmitted signals from an Earth station on an uplink frequency, amplifies the signals, and retransmits them on a downlink frequency to Earth. It functions as both a repeater and a frequency converter in space. Transponders are classified as either nonregenerative or regenerative. Nonregenerative transponders only alter the signal's amplitude and frequency, while regenerative transponders also alter the received signal before demodulation to offer flexibility in optimizing transmission link performance.
digital tank gauging system and DCS
A digital tank gauging system uses radar technology to monitor and control fuel storage tanks. It provides real-time tank level monitoring, inventory calculations, alarm handling and automated reports. The key components include radar level transmitters, temperature transmitters, a field communication unit, tank gauging software and an interface to other control systems. It offers advantages over standalone level instruments by integrating multiple measurements and automating inventory management tasks.
Tank Level to Base Radio and HMI Copy
A digital level transmitter on top of a tank wirelessly transmits tank product level data to a base unit located up to 3000 feet away. The base unit has a 4-inch touch screen display that shows the tank level using Modbus RTU serial communications.
Dual level to base radio back haul and hmi
This document provides information on a wireless monitoring system. It includes a 4-inch touch screen display and base unit housed in an enclosure. The base unit connects to sensors via RS-485 or RS-232 and provides power and communication with an external radio system for wireless transmission of data.
Tank level to base radio and hmi copy two
The Digital Level Transmitter located on top of the tank transmits tank product level data wirelessly to the Base Unit. The Base Unit then uses Modbus RTU communications to display the tank level data on a local 4-inch touch LCD display. Power is supplied to the display via the Base Unit's 12VDC power connector.
Tank point and continuous level to base radio and back haul
The document describes a wireless tank level monitoring system. A discrete or digital level transmitter on the tank transmits the local tank level data to a base unit display within 3000 feet. The base unit then transmits the tank level data to a field office using long haul radios for monitoring on a SCADA or touchscreen display.
Recommended
Hyrostatic to base unit and generic hmi
The document describes a digital level transmitter system that uses a transmitter on top of a tank to wirelessly transmit fluid head pressure data to a base unit. The base unit then displays the tank fluid head pressure on a 4-inch touch screen display using Modbus RTU communications. The system includes components like an enclosure, display, antenna, and power supplies.
Tank point and continuous level to base radio and back haul
The document describes a wireless tank level monitoring system. A discrete or digital level transmitter on the tank transmits the local tank level data to a base unit display within 3000 feet. The base unit then transmits the tank level data to a field office using long haul radios for monitoring on a touch screen display.
Transponder
A transponder is a device on a satellite that receives transmitted signals from an Earth station on an uplink frequency, amplifies the signals, and retransmits them on a downlink frequency to Earth. It functions as both a repeater and a frequency converter in space. Transponders are classified as either nonregenerative or regenerative. Nonregenerative transponders only alter the signal's amplitude and frequency, while regenerative transponders also alter the received signal before demodulation to offer flexibility in optimizing transmission link performance.
digital tank gauging system and DCS
A digital tank gauging system uses radar technology to monitor and control fuel storage tanks. It provides real-time tank level monitoring, inventory calculations, alarm handling and automated reports. The key components include radar level transmitters, temperature transmitters, a field communication unit, tank gauging software and an interface to other control systems. It offers advantages over standalone level instruments by integrating multiple measurements and automating inventory management tasks.
Tank Level to Base Radio and HMI Copy
A digital level transmitter on top of a tank wirelessly transmits tank product level data to a base unit located up to 3000 feet away. The base unit has a 4-inch touch screen display that shows the tank level using Modbus RTU serial communications.
Dual level to base radio back haul and hmi
This document provides information on a wireless monitoring system. It includes a 4-inch touch screen display and base unit housed in an enclosure. The base unit connects to sensors via RS-485 or RS-232 and provides power and communication with an external radio system for wireless transmission of data.
Tank level to base radio and hmi copy two
The Digital Level Transmitter located on top of the tank transmits tank product level data wirelessly to the Base Unit. The Base Unit then uses Modbus RTU communications to display the tank level data on a local 4-inch touch LCD display. Power is supplied to the display via the Base Unit's 12VDC power connector.
Tank point and continuous level to base radio and back haul
The document describes a wireless tank level monitoring system. A discrete or digital level transmitter on the tank transmits the local tank level data to a base unit display within 3000 feet. The base unit then transmits the tank level data to a field office using long haul radios for monitoring on a SCADA or touchscreen display.
Tank Level to Base Radio with HMI and Long Distance Radio
This document provides pricing and component information for a wireless monitoring system. The system includes a 10-foot wireless dual float unit for $1696.80, a wireless AC 4-inch display and base unit enclosure for $2100, and various additional components like a 4-inch touch screen display, RS-485 and RS-232 Modbus connections, a 12VDC and 110VAC power supply, and optional antennas not included in the base pricing.
Tank level to base radio with hmi and long distance radio
This document provides pricing and component information for a wireless monitoring system. The system includes a 10-foot wireless dual float unit for $1696.80, a wireless AC 4-inch display and base unit enclosure for $2100, and various additional components like a 4-inch touch screen display, RS-485 and RS-232 Modbus connections, a 12VDC and 110VAC power supply, and bulk mount and MDS antennas that are not included.
Rail car point and continuous level monitoring to hmi
The document is a diagram showing a wireless level alarm monitoring system. It includes a digital level transmitter that monitors continuous or discrete levels and transmits data to a base unit. The base unit includes an Omni antenna for wireless communication and interfaces with a Red Lion controller via Modbus RTU over RS485. Alarms are triggered when levels pass high or low thresholds.
Essential Guide Interfaces I/O 2010
The document discusses several options for industrial input/output systems:
1) Advantys AS-Interface cabling system simplifies connections with a single yellow cable.
2) Modicon Momentum distributed inputs/outputs simplify machine architectures by connecting sensors and actuators distributed throughout machines via fieldbus.
3) Advantys Telefast pre-wired system simplifies cabling by replacing long cable runs with pre-wired sub-bases.
Tank level to base radio and scadapack
The Digital Level Transmitter located on top of the Tank transmits temperature, product, and interface level data wirelessly to the Base Unit. The Base Unit then polls the tank data using serial Modbus RTU communications with the SCADAPack. The SCADAPack is powered by a 12 VDC battery charged by a solar panel and receives the tank data from the Base Unit over an RS485 Modbus connection.
Analog Input Digital Panel Meters
www.ucontrol.com.au - If you are looking the best digital panel meters services at reasonable prices.We are providing reaching alarms, universal input 4-20mA 0-10V, thermocouple, RTD with transmitter power supply.
American Fibertek MTX-91685C-SL User Manual
Buy the American Fibertek MTX-91685C-SL at JMAC Supply.
https://www.jmac.com/American_Fibertek_MTX_91685C_SL_p/american-fibertek-mtx-91685csl.htm?=slideshare
DCS Hardware Guide
The document provides information about a DCS system from the company DCS. It discusses the maxDPU4F distributed processing unit, which is the hardware processing engine of the DCS. The maxDPU4F performs primary data acquisition, control, and processing functions. It is a self-contained microprocessor-based unit that communicates with I/O modules and other devices over a maxNET network. The document also describes the front panel features of the maxDPU4F unit and provides specifications for its operation.
American Fibertek RT-946C Data Sheet
Buy the American Fibertek RT-946C at JMAC Supply.
https://www.jmac.com/American_Fibertek_RT_946C_p/american-fibertek-rt-946c.htm?=slideshare
Liquid Level Application - Site Survey
OleumTech Corporation provides industrial wireless automation solutions. The document discusses measuring tank height for their level transmitter products. It instructs that tank height should be measured from the installed face of the level transmitter at the top of the tank down to the bottom of the tank. The measurement captures the full height that the transmitter will need to measure to determine the liquid level within the tank.
Well head application overview copy
OleumTech provides wireless transmitters that can monitor oil and gas production facilities by transmitting sensor data like tank levels, pressures, temperatures, and flow rates to a central gateway unit. The transmitters are installed throughout the facility and can wirelessly transmit data from locations like oil and water tanks, separators, wellheads, and flowlines to help remotely monitor and manage the production process.
Well head application overview
This document provides a diagram of a gas production site. It shows various tanks and separators used to separate oil, gas, and water. Wireless transmitters throughout the site monitor and transmit data like levels, pressures, temperatures, and flows to a base unit gateway connected to an electronic flow measurement system. This allows for remote monitoring and measurement of production from the gas wells.
Upstream application overview and capabilites
This document describes a wireless monitoring system for an oil and gas wellhead. Wireless transmitters located throughout the production facility transmit levels, pressures, discrete values and temperatures to a wireless base unit. The base unit then transmits this data via serial Modbus RTU to an ABB control system. Digital outputs from the base unit are configured to open or close a sales valve based on process variables, providing high and high-high level alarm protection for the separator.
Underground water line pressure monitoring
The document describes a wireless man hole monitoring system. It uses a 6 element Yagi antenna to transmit data from sensors in man holes to a repeater and then to an Omni antenna on a server building. The system is powered by solar panels and uses analog transmitters and transducers to monitor water lines.
Tank Level to DH2 and ABB Peering Analog Out to Allen Bradley
The document describes a wireless tank level monitoring system. Wireless transmitters attached to tanks transmit level readings to a DH2 gateway. The DH2 then sends the tank levels via long haul radio to a base unit. The base unit provides 4-20mA analog outputs of the tank levels to a programmable logic controller for monitoring and control.
Irrigation center pivot and water pump control
This document describes a wireless peer-to-peer pressure monitoring system between two base units. Base Unit 1 transmits pressure readings from a Wika Pressure Transducer via Yagi antenna to Base Unit 2. Base Unit 2 then uses the pressure readings to control a water pump at the pump house by outputting a 4-20mA signal based on the pressure levels. The system is powered by solar panels and batteries.
Hi Level Alarm to Base Unit to Red Lion with Alarm
The document is an electrical diagram showing a wireless high level alarm monitoring system. It includes an omni antenna, base unit, Modbus RTU RS485 interface, discrete transmitter, hi level alarm, interposing relay coil, 12VDC power supply, and 110VAC power supply. The system monitors hi level alarms wirelessly.
Tank level to dh2 and abb peering analog out to allen bradley
The document describes a wireless tank level monitoring system. Wireless transmitters attached to tanks transmit level readings to a DH2 gateway. The DH2 then sends the tank levels via long haul radio to a base unit. The base unit provides 4-20mA analog outputs of the tank levels to a programmable logic controller for monitoring and control.
Saltwater disposal overview copy
The document describes a base unit used for high level shutdown of salt water tanks. It uses digital and discrete transmitters to monitor tank levels and control valves. When tank levels reach a high point, interposing relays activate solenoid coils to close normally open valves and open normally closed valves to prevent overfilling. The system is powered by solar panels and batteries.
Multiple end nodes with analog out
The document describes a new wireless temperature monitoring system. Temperature transmitters located throughout multiple plant areas transmit temperature readings wirelessly to a new wireless gateway system. The gateway collects the individual 4-20mA temperature signals and transmits them to the PLC, replacing the existing wired system. The wireless system uses multiple base units and transmitter groups to monitor temperatures across four plant areas.
Hi Level Alarm to Base Unit to Red Lion with Alarm
The document is an electrical diagram showing a wireless high level alarm monitoring system. It includes an omni antenna, base unit, Modbus RTU RS485 interface, discrete transmitter, hi level alarm, interposing relay coil, 12VDC power supply, and 110VAC power supply. The system monitors hi level alarms wirelessly.
Base Unit AC CP
The document describes an AC cathodic protection base unit. It includes a 0-50 VDC to 1-5 VDC voltage regulator, a 12 VDC power supply, a current transducer, and a 250mA fuse to protect the unit. The base unit steps down the AC voltage input to power the internal components and regulates the DC output voltage to protect structures.
More Related Content
Similar to Tank level to base radio and hmi
Tank Level to Base Radio with HMI and Long Distance Radio
This document provides pricing and component information for a wireless monitoring system. The system includes a 10-foot wireless dual float unit for $1696.80, a wireless AC 4-inch display and base unit enclosure for $2100, and various additional components like a 4-inch touch screen display, RS-485 and RS-232 Modbus connections, a 12VDC and 110VAC power supply, and optional antennas not included in the base pricing.
Tank level to base radio with hmi and long distance radio
This document provides pricing and component information for a wireless monitoring system. The system includes a 10-foot wireless dual float unit for $1696.80, a wireless AC 4-inch display and base unit enclosure for $2100, and various additional components like a 4-inch touch screen display, RS-485 and RS-232 Modbus connections, a 12VDC and 110VAC power supply, and bulk mount and MDS antennas that are not included.
Rail car point and continuous level monitoring to hmi
The document is a diagram showing a wireless level alarm monitoring system. It includes a digital level transmitter that monitors continuous or discrete levels and transmits data to a base unit. The base unit includes an Omni antenna for wireless communication and interfaces with a Red Lion controller via Modbus RTU over RS485. Alarms are triggered when levels pass high or low thresholds.
Essential Guide Interfaces I/O 2010
The document discusses several options for industrial input/output systems:
1) Advantys AS-Interface cabling system simplifies connections with a single yellow cable.
2) Modicon Momentum distributed inputs/outputs simplify machine architectures by connecting sensors and actuators distributed throughout machines via fieldbus.
3) Advantys Telefast pre-wired system simplifies cabling by replacing long cable runs with pre-wired sub-bases.
Tank level to base radio and scadapack
The Digital Level Transmitter located on top of the Tank transmits temperature, product, and interface level data wirelessly to the Base Unit. The Base Unit then polls the tank data using serial Modbus RTU communications with the SCADAPack. The SCADAPack is powered by a 12 VDC battery charged by a solar panel and receives the tank data from the Base Unit over an RS485 Modbus connection.
Analog Input Digital Panel Meters
www.ucontrol.com.au - If you are looking the best digital panel meters services at reasonable prices.We are providing reaching alarms, universal input 4-20mA 0-10V, thermocouple, RTD with transmitter power supply.
American Fibertek MTX-91685C-SL User Manual
Buy the American Fibertek MTX-91685C-SL at JMAC Supply.
https://www.jmac.com/American_Fibertek_MTX_91685C_SL_p/american-fibertek-mtx-91685csl.htm?=slideshare
DCS Hardware Guide
The document provides information about a DCS system from the company DCS. It discusses the maxDPU4F distributed processing unit, which is the hardware processing engine of the DCS. The maxDPU4F performs primary data acquisition, control, and processing functions. It is a self-contained microprocessor-based unit that communicates with I/O modules and other devices over a maxNET network. The document also describes the front panel features of the maxDPU4F unit and provides specifications for its operation.
American Fibertek RT-946C Data Sheet
Buy the American Fibertek RT-946C at JMAC Supply.
https://www.jmac.com/American_Fibertek_RT_946C_p/american-fibertek-rt-946c.htm?=slideshare
Similar to Tank level to base radio and hmi (9)
Tank Level to Base Radio with HMI and Long Distance Radio
Tank Level to Base Radio with HMI and Long Distance Radio
Tank level to base radio with hmi and long distance radio
Tank level to base radio with hmi and long distance radio
Rail car point and continuous level monitoring to hmi
Rail car point and continuous level monitoring to hmi
More from Asif Sheriff
Liquid Level Application - Site Survey
OleumTech Corporation provides industrial wireless automation solutions. The document discusses measuring tank height for their level transmitter products. It instructs that tank height should be measured from the installed face of the level transmitter at the top of the tank down to the bottom of the tank. The measurement captures the full height that the transmitter will need to measure to determine the liquid level within the tank.
Well head application overview copy
OleumTech provides wireless transmitters that can monitor oil and gas production facilities by transmitting sensor data like tank levels, pressures, temperatures, and flow rates to a central gateway unit. The transmitters are installed throughout the facility and can wirelessly transmit data from locations like oil and water tanks, separators, wellheads, and flowlines to help remotely monitor and manage the production process.
Well head application overview
This document provides a diagram of a gas production site. It shows various tanks and separators used to separate oil, gas, and water. Wireless transmitters throughout the site monitor and transmit data like levels, pressures, temperatures, and flows to a base unit gateway connected to an electronic flow measurement system. This allows for remote monitoring and measurement of production from the gas wells.
Upstream application overview and capabilites
This document describes a wireless monitoring system for an oil and gas wellhead. Wireless transmitters located throughout the production facility transmit levels, pressures, discrete values and temperatures to a wireless base unit. The base unit then transmits this data via serial Modbus RTU to an ABB control system. Digital outputs from the base unit are configured to open or close a sales valve based on process variables, providing high and high-high level alarm protection for the separator.
Underground water line pressure monitoring
The document describes a wireless man hole monitoring system. It uses a 6 element Yagi antenna to transmit data from sensors in man holes to a repeater and then to an Omni antenna on a server building. The system is powered by solar panels and uses analog transmitters and transducers to monitor water lines.
Tank Level to DH2 and ABB Peering Analog Out to Allen Bradley
The document describes a wireless tank level monitoring system. Wireless transmitters attached to tanks transmit level readings to a DH2 gateway. The DH2 then sends the tank levels via long haul radio to a base unit. The base unit provides 4-20mA analog outputs of the tank levels to a programmable logic controller for monitoring and control.
Irrigation center pivot and water pump control
This document describes a wireless peer-to-peer pressure monitoring system between two base units. Base Unit 1 transmits pressure readings from a Wika Pressure Transducer via Yagi antenna to Base Unit 2. Base Unit 2 then uses the pressure readings to control a water pump at the pump house by outputting a 4-20mA signal based on the pressure levels. The system is powered by solar panels and batteries.
Hi Level Alarm to Base Unit to Red Lion with Alarm
The document is an electrical diagram showing a wireless high level alarm monitoring system. It includes an omni antenna, base unit, Modbus RTU RS485 interface, discrete transmitter, hi level alarm, interposing relay coil, 12VDC power supply, and 110VAC power supply. The system monitors hi level alarms wirelessly.
Tank level to dh2 and abb peering analog out to allen bradley
The document describes a wireless tank level monitoring system. Wireless transmitters attached to tanks transmit level readings to a DH2 gateway. The DH2 then sends the tank levels via long haul radio to a base unit. The base unit provides 4-20mA analog outputs of the tank levels to a programmable logic controller for monitoring and control.
Saltwater disposal overview copy
The document describes a base unit used for high level shutdown of salt water tanks. It uses digital and discrete transmitters to monitor tank levels and control valves. When tank levels reach a high point, interposing relays activate solenoid coils to close normally open valves and open normally closed valves to prevent overfilling. The system is powered by solar panels and batteries.
Multiple end nodes with analog out
The document describes a new wireless temperature monitoring system. Temperature transmitters located throughout multiple plant areas transmit temperature readings wirelessly to a new wireless gateway system. The gateway collects the individual 4-20mA temperature signals and transmits them to the PLC, replacing the existing wired system. The wireless system uses multiple base units and transmitter groups to monitor temperatures across four plant areas.
Hi Level Alarm to Base Unit to Red Lion with Alarm
The document is an electrical diagram showing a wireless high level alarm monitoring system. It includes an omni antenna, base unit, Modbus RTU RS485 interface, discrete transmitter, hi level alarm, interposing relay coil, 12VDC power supply, and 110VAC power supply. The system monitors hi level alarms wirelessly.
Base Unit AC CP
The document describes an AC cathodic protection base unit. It includes a 0-50 VDC to 1-5 VDC voltage regulator, a 12 VDC power supply, a current transducer, and a 250mA fuse to protect the unit. The base unit steps down the AC voltage input to power the internal components and regulates the DC output voltage to protect structures.
Tank level to base radio with analog out
The document describes a wireless digital level transmitter that transmits tank levels to a base unit. The base unit then provides a 4-20mA output representing the current tank level. The transmitter is located on the tank and wirelessly communicates the level to the base unit.
Saltwater disposal overview
The document provides a diagram of an oilfield equipment system that uses wireless transmitters and a base unit to control valves and monitor levels for salt water disposal from oil production operations. Key components include a digital level transmitter, interposing relays, solar panels, and valves that can be opened or closed through valve solenoids to control flow into salt water tanks or injection wells. The base unit integrates data from the wireless transmitters and controls pumps, valves, and alarms through a network of wired and wireless connections.
Sump pit level generic to dh2
This document shows a diagram for wireless monitoring of man hole levels. It depicts an omni antenna wirelessly connected to an HMI interface to monitor levels from various probes and transmitters in a man hole. Analog and digital signals from level probes and transmitters are sent via Modbus RTU to the HMI for remote monitoring of hydrostatic levels.
Pump control with tank level monitoring
The document describes a wireless digital level transmitter that transmits tank levels to a base unit. The base unit uses the transmitted tank levels to control a pump start relay and stop the pump based on predetermined tank levels. The system includes a 12VDC power supply that powers the digital level transmitter and a 100-240VAC power input for the base unit and pump start relay.
Pump control with flow line pressure monitoring
This document describes a wireless pipeline pressure monitoring system. It has a discrete transmitter connected to a pressure switch on the pipeline that sends high or low pressure alarm statuses to a base unit. The base unit then controls a pump start relay based on the pressure readings from the transmitter to regulate the pipeline pressure.
Pump control.with base radio
This diagram shows a power supply unit that converts 100-240 VAC input power to 12 VDC output power. It uses a 250mA fuse, 12 volt DC coil, and 10 amp AC contact to regulate the power and safely power a pump start relay. The overall unit provides protected and regulated 12 VDC power from a standard 100-240 VAC source.
Plunger lift real time - 3 wire arrival sensor with solar panel voltage mon...
This document provides a diagram and description of the wiring for an OleumTech base unit application. The diagram shows a solar panel, battery, pressure transducer, arrival sensor, interposing relay coil, 250mA fuse, and valve solenoid coil connected to a base unit that converts a 0-50 VDC signal from the pressure transducer to a 1-5 VDC signal. The base unit provides power regulation and signal conversion for the application.
More from Asif Sheriff (20)
Tank Level to DH2 and ABB Peering Analog Out to Allen Bradley
Tank Level to DH2 and ABB Peering Analog Out to Allen Bradley
Hi Level Alarm to Base Unit to Red Lion with Alarm
Hi Level Alarm to Base Unit to Red Lion with Alarm
Tank level to dh2 and abb peering analog out to allen bradley
Tank level to dh2 and abb peering analog out to allen bradley
Hi Level Alarm to Base Unit to Red Lion with Alarm
Hi Level Alarm to Base Unit to Red Lion with Alarm
Plunger lift real time - 3 wire arrival sensor with solar panel voltage mon...
Plunger lift real time - 3 wire arrival sensor with solar panel voltage mon...
Recently uploaded
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
Driving Business Innovation: Latest Generative AI Advancements & Success Story
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
Presentation of the OECD Artificial Intelligence Review of Germany
Consult the full report at https://www.oecd.org/digital/oecd-artificial-intelligence-review-of-germany-609808d6-en.htm
UiPath Test Automation using UiPath Test Suite series, part 5
Welcome to UiPath Test Automation using UiPath Test Suite series part 5. In this session, we will cover CI/CD with devops.
Topics covered:
CI/CD with in UiPath
End-to-end overview of CI/CD pipeline with Azure devops
Speaker:
Lyndsey Byblow, Test Suite Sales Engineer @ UiPath, Inc.
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
20240607 QFM018 Elixir Reading List May 2024
Everything I found interesting about the Elixir programming ecosystem in May 2024
Building Production Ready Search Pipelines with Spark and Milvus
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
HCL Notes and Domino License Cost Reduction in the World of DLAU
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-and-domino-license-cost-reduction-in-the-world-of-dlau/
The introduction of DLAU and the CCB & CCX licensing model caused quite a stir in the HCL community. As a Notes and Domino customer, you may have faced challenges with unexpected user counts and license costs. You probably have questions on how this new licensing approach works and how to benefit from it. Most importantly, you likely have budget constraints and want to save money where possible. Don’t worry, we can help with all of this!
We’ll show you how to fix common misconfigurations that cause higher-than-expected user counts, and how to identify accounts which you can deactivate to save money. There are also frequent patterns that can cause unnecessary cost, like using a person document instead of a mail-in for shared mailboxes. We’ll provide examples and solutions for those as well. And naturally we’ll explain the new licensing model.
Join HCL Ambassador Marc Thomas in this webinar with a special guest appearance from Franz Walder. It will give you the tools and know-how to stay on top of what is going on with Domino licensing. You will be able lower your cost through an optimized configuration and keep it low going forward.
These topics will be covered
- Reducing license cost by finding and fixing misconfigurations and superfluous accounts
- How do CCB and CCX licenses really work?
- Understanding the DLAU tool and how to best utilize it
- Tips for common problem areas, like team mailboxes, functional/test users, etc
- Practical examples and best practices to implement right away
20240609 QFM020 Irresponsible AI Reading List May 2024
Everything I found interesting about the irresponsible use of machine intelligence in May 2024
Pushing the limits of ePRTC: 100ns holdover for 100 days
At WSTS 2024, Alon Stern explored the topic of parametric holdover and explained how recent research findings can be implemented in real-world PNT networks to achieve 100 nanoseconds of accuracy for up to 100 days.
20240605 QFM017 Machine Intelligence Reading List May 2024
Everything I found interesting about machines behaving intelligently during May 2024
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
Maruthi Prithivirajan, Head of ASEAN & IN Solution Architecture, Neo4j
Get an inside look at the latest Neo4j innovations that enable relationship-driven intelligence at scale. Learn more about the newest cloud integrations and product enhancements that make Neo4j an essential choice for developers building apps with interconnected data and generative AI.
Uni Systems Copilot event_05062024_C.Vlachos.pdf
Unlocking Productivity: Leveraging the Potential of Copilot in Microsoft 365, a presentation by Christoforos Vlachos, Senior Solutions Manager – Modern Workplace, Uni Systems
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
Communications Mining Series - Zero to Hero - Session 1
This session provides introduction to UiPath Communication Mining, importance and platform overview. You will acquire a good understand of the phases in Communication Mining as we go over the platform with you. Topics covered:
• Communication Mining Overview
• Why is it important?
• How can it help today’s business and the benefits
• Phases in Communication Mining
• Demo on Platform overview
• Q/A
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...Edge AI and Vision Alliance
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.TrustArc Webinar - 2024 Global Privacy Survey
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
Recently uploaded (20)
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Driving Business Innovation: Latest Generative AI Advancements & Success Story
Driving Business Innovation: Latest Generative AI Advancements & Success Story
Presentation of the OECD Artificial Intelligence Review of Germany
Presentation of the OECD Artificial Intelligence Review of Germany
UiPath Test Automation using UiPath Test Suite series, part 5
UiPath Test Automation using UiPath Test Suite series, part 5
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Building Production Ready Search Pipelines with Spark and Milvus
Building Production Ready Search Pipelines with Spark and Milvus
HCL Notes and Domino License Cost Reduction in the World of DLAU
HCL Notes and Domino License Cost Reduction in the World of DLAU
20240609 QFM020 Irresponsible AI Reading List May 2024
20240609 QFM020 Irresponsible AI Reading List May 2024
Pushing the limits of ePRTC: 100ns holdover for 100 days
Pushing the limits of ePRTC: 100ns holdover for 100 days
20240605 QFM017 Machine Intelligence Reading List May 2024
20240605 QFM017 Machine Intelligence Reading List May 2024
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
Communications Mining Series - Zero to Hero - Session 1
Communications Mining Series - Zero to Hero - Session 1
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
Tank level to base radio and hmi
- 1. The Digital Level Transmitter located on top of the tank transmits tank product level data to the Base Unit wireless. The tank level is displayed on the local 4" display Digital Level using serial Modbus RTU Transmitter communications. Enclosure 14X12 4" Touch Screen Display RS 485 500mA Fuse Modbus Base Unit 12 VDC Power Supply OleumTech Bulk Mount Antenna 110 VAC Supply OleumTech