This document contains a service manual for Tier 4B (final) engines. It includes sections on the engine, electrical systems, and safety information. The manual provides maintenance and repair instructions for technicians, with the goal of ensuring personal safety and preventing damage to equipment. It lists many engine part numbers and cautions technicians to only perform work according to the procedures in the manual using recommended tools.
2007 toyota highlander service repair manualfujjsekfkksekm
This document provides instructions on how to use the 2005 Highlander repair manual. It discusses the manual's organization and contents, including repair procedures, specifications, identification information, and precautions. Proper techniques are emphasized, such as using torque wrenches, replacing non-reusable parts, and correctly removing and installing clips, bolts, and vacuum hoses. Safety is also stressed, advising technicians to properly support vehicles, wear protective equipment, and avoid mixing up removed parts.
2007 polaris 600 ho switchback snowmobile service repair manualfujjsekfkksekm
The document provides specifications for the 2007-2008 IQ Snowmobile models including engine details, dimensions, weight, fuel capacity, electrical system information, track details, and suspension components. It lists specifications for individual models such as the 600 HO IQ, 600 HO Switchback, 700 HO IQ Dragon, and others. Jetting charts are provided for adjusting the carburetor based on altitude and temperature.
2007 lexus gs300 gs430 s190 service repair manualfujjsekfkksekm
This document provides general repair instructions and guidelines for working with body panels. It discusses safety precautions when welding, handling plastic body parts, and performing installations. Specific details are given for measuring parts, making cuts and welds, and ensuring a proper fit of replacement parts. Proper work procedures are outlined, including removal techniques, preparation for installation, and inspection after reassembly.
This document provides specifications and repair information for the 2004 Saturn Vue rear drive axle. It includes specifications for fastener tightening torques, rear axle components, lubricant types, and diagnostic procedures for various rear axle noises like noisy when driving, coasting, or turning. The document contains diagrams of the rear axle disassembled and the differential carrier components to aid in diagnosis and repair. It provides steps to diagnose issues like low fluid levels, worn joints, loose mounts, and noises related to the rear axle, propeller shaft, or transfer case.
2006 kawasaki ex650 a6f service repair manualfujjsekfkksekm
This document is a service manual for the Ninja 650R, ER-6f ABS, and ER-6f motorcycles. It provides instructions and procedures for maintenance and repair of these motorcycles. The manual begins with a quick reference guide and table of contents to help technicians easily locate specific information. It then covers general safety information, emissions control systems, and how to use the service manual properly.
The document is a Toyota repair manual that provides maintenance, preparation, specifications, and diagnostic information for Toyota vehicles. It includes sections on engine mechanical systems, emission control, cooling, lubrication, ignition, starting, charging, transmissions, suspension, brakes, steering, air conditioning and more. The document contains detailed procedures, specifications, diagrams and other technical information to assist technicians with repairing and servicing Toyota vehicles.
2005 honda trx500 tm fourtrax foreman service repair manualfujjsekfkksekm
This service manual provides specifications and maintenance procedures for 2005-2006 Honda TRX500FE/FM four-wheel all-terrain vehicles. The manual covers identification information, maintenance schedules, specifications for parts and systems, standard torque values, and cable routing diagrams. Safety information is provided throughout and procedures are described for inspection and repair of engine, transmission, brakes, suspension, electrical and other systems.
2004 nissan frontier service repair manualfujjsekfkksekm
This document contains a quick reference chart for the 2004 Nissan Frontier equipped with a KA24DE engine. It includes sections with information on engine specifications, tune-up data, transmission specifications, suspension specifications, brake specifications, refill capacities, and more. The document aims to provide technicians with essential technical specifications and repair limit values for servicing the vehicle in an efficient and safe manner.
2007 toyota highlander service repair manualfujjsekfkksekm
This document provides instructions on how to use the 2005 Highlander repair manual. It discusses the manual's organization and contents, including repair procedures, specifications, identification information, and precautions. Proper techniques are emphasized, such as using torque wrenches, replacing non-reusable parts, and correctly removing and installing clips, bolts, and vacuum hoses. Safety is also stressed, advising technicians to properly support vehicles, wear protective equipment, and avoid mixing up removed parts.
2007 polaris 600 ho switchback snowmobile service repair manualfujjsekfkksekm
The document provides specifications for the 2007-2008 IQ Snowmobile models including engine details, dimensions, weight, fuel capacity, electrical system information, track details, and suspension components. It lists specifications for individual models such as the 600 HO IQ, 600 HO Switchback, 700 HO IQ Dragon, and others. Jetting charts are provided for adjusting the carburetor based on altitude and temperature.
2007 lexus gs300 gs430 s190 service repair manualfujjsekfkksekm
This document provides general repair instructions and guidelines for working with body panels. It discusses safety precautions when welding, handling plastic body parts, and performing installations. Specific details are given for measuring parts, making cuts and welds, and ensuring a proper fit of replacement parts. Proper work procedures are outlined, including removal techniques, preparation for installation, and inspection after reassembly.
This document provides specifications and repair information for the 2004 Saturn Vue rear drive axle. It includes specifications for fastener tightening torques, rear axle components, lubricant types, and diagnostic procedures for various rear axle noises like noisy when driving, coasting, or turning. The document contains diagrams of the rear axle disassembled and the differential carrier components to aid in diagnosis and repair. It provides steps to diagnose issues like low fluid levels, worn joints, loose mounts, and noises related to the rear axle, propeller shaft, or transfer case.
2006 kawasaki ex650 a6f service repair manualfujjsekfkksekm
This document is a service manual for the Ninja 650R, ER-6f ABS, and ER-6f motorcycles. It provides instructions and procedures for maintenance and repair of these motorcycles. The manual begins with a quick reference guide and table of contents to help technicians easily locate specific information. It then covers general safety information, emissions control systems, and how to use the service manual properly.
The document is a Toyota repair manual that provides maintenance, preparation, specifications, and diagnostic information for Toyota vehicles. It includes sections on engine mechanical systems, emission control, cooling, lubrication, ignition, starting, charging, transmissions, suspension, brakes, steering, air conditioning and more. The document contains detailed procedures, specifications, diagrams and other technical information to assist technicians with repairing and servicing Toyota vehicles.
2005 honda trx500 tm fourtrax foreman service repair manualfujjsekfkksekm
This service manual provides specifications and maintenance procedures for 2005-2006 Honda TRX500FE/FM four-wheel all-terrain vehicles. The manual covers identification information, maintenance schedules, specifications for parts and systems, standard torque values, and cable routing diagrams. Safety information is provided throughout and procedures are described for inspection and repair of engine, transmission, brakes, suspension, electrical and other systems.
2004 nissan frontier service repair manualfujjsekfkksekm
This document contains a quick reference chart for the 2004 Nissan Frontier equipped with a KA24DE engine. It includes sections with information on engine specifications, tune-up data, transmission specifications, suspension specifications, brake specifications, refill capacities, and more. The document aims to provide technicians with essential technical specifications and repair limit values for servicing the vehicle in an efficient and safe manner.
This document provides instructions on how to use the service manual for the 2003 Toyota Tundra. It discusses the manual's organization including the index, precautions, troubleshooting tables, preparation sections, repair procedures, references, specifications, cautions, and units of measurement. The repair procedures use a standardized format with illustrations, task headings, and detailed text. The document also provides general repair instructions and identifies vehicle and engine identification locations.
2003 nissan frontier service repair manualfujjsekfkksekm
This document provides a quick reference index and chart for the 2003 Nissan Frontier equipped with the KA24DE engine. It includes sections on general engine information, specifications for components like the engine, transmission, driveline, brakes, and electrical systems. The chart also lists specifications such as idle speed and ignition timing, belt deflection and tension values, spark plug and filter information, fluid capacities, and repair limits.
This document provides instructions for inspecting and adjusting the engine on a 2007 Lexus GX 470. It outlines several inspection and measurement procedures to check engine components like the engine cooling system, oil, battery, air filter, belts, ignition timing, idle speed, compression, emissions, and valve clearance. The valve clearance adjustment procedure involves removing various engine covers and components, measuring the current clearance, determining the needed shim thickness based on specifications, and replacing shims as needed.
This document appears to be a repair manual containing sections on general information, various vehicle systems, and scheduled maintenance for a daily vehicle. It includes identification data for the vehicle, an explanation of vehicle model compositions and available assemblies, and alphanumerical coding systems for vehicle and bus identification. The sections provide information on replenishing fluids, vehicle identification plates and stamps, and index the topics that each section covers in detail.
This document provides instructions for adjusting the valve clearance on a 2000-2001 Chevrolet Prizm with a 1.8L 4-cylinder engine. The procedure involves rotating the crankshaft to specific positions and checking clearance between the camshaft lobe and adjusting shim using a feeler gauge. If clearance is outside specifications, the adjusting shim is replaced. Charts are provided to select the correct shim thickness. Instructions are also given for removing the cylinder head and related components to access the camshafts and adjusting shims.
This document provides information on adjusting the valve clearance for a 1997-98 3.0L V6 engine. It describes locating the engine serial number and identifying the engine code. The procedure involves removing valve covers and ignition coils, rotating the crankshaft to specific positions, measuring valve clearance with a feeler gauge, and if needed, adjusting clearance by replacing the adjusting shim. Charts are provided to select the correct replacement shim thickness.
1996 polaris indy storm sks snowmobile service repair manualfujjsekfkksekm
This document provides publication numbers and service bulletin indexes for Polaris snowmobiles from 1994-1998. It lists the model, model number, owner's manual part number, parts manual part number, and other relevant documentation for each year. The document also provides indexes of service bulletins by number and year to allow technicians to quickly look up technical service information.
1992 yamaha vmx1200 d v max service repair manualfujjsekfkksekm
1. The document provides specifications and maintenance procedures for a VMX12 motorcycle, including engine oil replacement instructions, engine overhaul procedures, and inspection of parts like the crankshaft, balancer shaft, and middle gear components.
2. Specifications include identification numbers, weights, fluids and clearances. Maintenance procedures describe how to inspect, measure and replace parts like the crankshaft bearings, balancer shaft bearings, and middle gear components.
3. Tools needed include an oil filter wrench and Plastigauge for measuring oil clearances. Special attention is given to bearing selection and installation orientation to ensure proper clearance.
1988 polaris sprint snowmobile service repair manualfujjsekfkksekm
The document describes Polaris snowmobile models and specifications from 1985 to 1995. It provides details on model identification by serial number and model number. For each year from 1985 to 1995, the document lists the models produced that year and provides specifications for each, including engine type, displacement, dimensions, suspension, brakes, storage and other details.
Kubota st alpha-35 tractor service repair manualfujjsekfkksekm
This document provides maintenance information for STα-30 and STα-35 tractors. It discusses general precautions for handling electrical parts and wiring, recommended lubricants and fluids, and maintenance check points to perform every 50, 100, 200, 400 hours or yearly/2-yearly. Precautions are given for safe handling of batteries, fuses, connectors and circuit testers. Wiring should be securely clamped without damage and terminals properly protected. Only specified lubricants and fuels should be used in the tractor systems.
Kubota rck72 f36 front cut ride on mower service repair manualfujjsekfkksekm
This document provides a workshop manual for F2880, F3680, RCK72-F36, RCK72R-F36, RCK60-F36, and RCK60R-F36 machines. It includes sections on identification, general precautions, handling electrical parts and wiring safely, recommended lubricants and fluids, tightening torques, maintenance checklists, inspection schedules, special tools, tire pressures, and implement limitations. Safety is emphasized, including proper handling of batteries, fuses, connectors and circuit testers. Detailed inspection procedures are given for daily, 50-hour, 100-hour, 200-hour, 400-hour, 1500-hour, 3000-hour and yearly maintenance
Kubota gr2100 ec lawnmower service repair manualfujjsekfkksekm
This document provides guidelines and specifications for maintenance tasks on a GR2100EC workshop manual. It includes:
- Identification information needed when contacting a dealer, such as serial numbers and hour meter reading.
- General precautions for disassembly/reassembly, use of special tools, electrical work, and lubrication.
- Guidelines for handling electrical parts and wiring, including batteries, fuses, connectors and circuit testing.
- Specifications for lubricants, fuel, coolant and greasing points.
- Tightening torque specifications for bolts, nuts and plugs.
Kubota gr1600 ec2 ride on mower service repair manualfujjsekfkksekm
This document provides information on identification, general precautions, handling precautions for electrical parts and wiring, lubricants, fuel and coolant, tightening torques, maintenance checklists, and special tools for a GR1600EC2 workshop manual. It identifies lubrication points and specifies lubricants, fuels, and coolants for the engine, transmission, cooling system, and other components. Precautions are outlined for safe handling of electrical parts, batteries, fuses, connectors and circuit testers. Tightening torques are provided for various screw types. Maintenance checklists specify daily, 50-hour, 100-hour and other periodic inspection points.
Steyr profi cvt 4130 tractor service repair manualfujjsekfkksekm
This document is a service manual that provides maintenance and repair information for various PROFI tractor models, including the PROFI 4110 ET, PROFI 4120 ET, PROFI 4130 ET, PROFI 6125 ET, PROFI 6140 ET, and PROFI CVT models. The manual contains sections on the engine, transmission, axle systems, hydraulics, electrical systems, and other components. It includes technical specifications, descriptions of component operation, troubleshooting information, and repair/replacement procedures.
Steyr profi cvt 4120 tractor service repair manualfujjsekfkksekm
This document is a service manual that provides maintenance and repair information for various PROFI tractor models, including the PROFI 4110 ET, PROFI 4120 ET, PROFI 4130 ET, PROFI 6125 ET, PROFI 6140 ET, and PROFI CVT models. The manual contains sections on the engine, transmission, axle systems, hydraulics, electrical systems, and other components. It includes technical specifications, descriptions of component operation, troubleshooting information, and repair procedures.
This document is a service and training manual for tractors models M9078, M9086, and M9094. It contains a table of contents listing the sections and publication numbers for various workshop manuals and how-to guides covering the engine, fuel system, electrical systems, steering systems, transmission, and hydraulic systems of the tractors. The manuals provide information on troubleshooting, maintenance, and repair for different components and systems of the tractors.
Steyr kompakt 4115 ecotech tractor service repair manual (pin zdjz16683 and a...fujjsekfkksekm
This document is a service manual for Kompakt 4075, 4085, 4095, 4105, and 4115 tractors. It contains an introduction and table of contents that outlines the major systems covered in the manual, including the engine, transmission, axles, hydraulics, steering, brakes, electrical systems, and more. Each system includes links to detailed sections that provide specifications, component locations, maintenance and repair instructions.
Steyr f4 dfe4131 tier 4b (final) engine service repair manualfujjsekfkksekm
This document contains a service manual for Tier 4B (final) engines. It includes sections on the engine, electrical systems, and safety information. The manual provides maintenance and repair instructions for technicians, with the goal of ensuring personal safety and preventing damage to equipment. It lists many engine part numbers and cautions technicians to only perform work according to the procedures in the manual using recommended tools.
Steyr cvt 6215 tractor service repair manualfujjsekfkksekm
This document is a service manual for CVT 6170, CVT 6185, CVT 6205, CVT 6215, and CVT 6230 tractors. It contains part numbers, links the tractors to their engine models, and provides a table of contents that lists the systems and components covered in each section of the manual, including the engine, transmission, axles, hydraulics, electrical systems, and more. The manual is intended to provide technical information and guidance for servicing the listed tractor models.
Steyr cvt 6195 tractor service repair manualfujjsekfkksekm
This document is a service manual for CVT6140, CVT6150, CVT6160, CVT6175, and CVT6195 tractors. It contains an introduction and safety information, as well as sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, cab climate control, and electrical systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the various components.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
This document provides instructions on how to use the service manual for the 2003 Toyota Tundra. It discusses the manual's organization including the index, precautions, troubleshooting tables, preparation sections, repair procedures, references, specifications, cautions, and units of measurement. The repair procedures use a standardized format with illustrations, task headings, and detailed text. The document also provides general repair instructions and identifies vehicle and engine identification locations.
2003 nissan frontier service repair manualfujjsekfkksekm
This document provides a quick reference index and chart for the 2003 Nissan Frontier equipped with the KA24DE engine. It includes sections on general engine information, specifications for components like the engine, transmission, driveline, brakes, and electrical systems. The chart also lists specifications such as idle speed and ignition timing, belt deflection and tension values, spark plug and filter information, fluid capacities, and repair limits.
This document provides instructions for inspecting and adjusting the engine on a 2007 Lexus GX 470. It outlines several inspection and measurement procedures to check engine components like the engine cooling system, oil, battery, air filter, belts, ignition timing, idle speed, compression, emissions, and valve clearance. The valve clearance adjustment procedure involves removing various engine covers and components, measuring the current clearance, determining the needed shim thickness based on specifications, and replacing shims as needed.
This document appears to be a repair manual containing sections on general information, various vehicle systems, and scheduled maintenance for a daily vehicle. It includes identification data for the vehicle, an explanation of vehicle model compositions and available assemblies, and alphanumerical coding systems for vehicle and bus identification. The sections provide information on replenishing fluids, vehicle identification plates and stamps, and index the topics that each section covers in detail.
This document provides instructions for adjusting the valve clearance on a 2000-2001 Chevrolet Prizm with a 1.8L 4-cylinder engine. The procedure involves rotating the crankshaft to specific positions and checking clearance between the camshaft lobe and adjusting shim using a feeler gauge. If clearance is outside specifications, the adjusting shim is replaced. Charts are provided to select the correct shim thickness. Instructions are also given for removing the cylinder head and related components to access the camshafts and adjusting shims.
This document provides information on adjusting the valve clearance for a 1997-98 3.0L V6 engine. It describes locating the engine serial number and identifying the engine code. The procedure involves removing valve covers and ignition coils, rotating the crankshaft to specific positions, measuring valve clearance with a feeler gauge, and if needed, adjusting clearance by replacing the adjusting shim. Charts are provided to select the correct replacement shim thickness.
1996 polaris indy storm sks snowmobile service repair manualfujjsekfkksekm
This document provides publication numbers and service bulletin indexes for Polaris snowmobiles from 1994-1998. It lists the model, model number, owner's manual part number, parts manual part number, and other relevant documentation for each year. The document also provides indexes of service bulletins by number and year to allow technicians to quickly look up technical service information.
1992 yamaha vmx1200 d v max service repair manualfujjsekfkksekm
1. The document provides specifications and maintenance procedures for a VMX12 motorcycle, including engine oil replacement instructions, engine overhaul procedures, and inspection of parts like the crankshaft, balancer shaft, and middle gear components.
2. Specifications include identification numbers, weights, fluids and clearances. Maintenance procedures describe how to inspect, measure and replace parts like the crankshaft bearings, balancer shaft bearings, and middle gear components.
3. Tools needed include an oil filter wrench and Plastigauge for measuring oil clearances. Special attention is given to bearing selection and installation orientation to ensure proper clearance.
1988 polaris sprint snowmobile service repair manualfujjsekfkksekm
The document describes Polaris snowmobile models and specifications from 1985 to 1995. It provides details on model identification by serial number and model number. For each year from 1985 to 1995, the document lists the models produced that year and provides specifications for each, including engine type, displacement, dimensions, suspension, brakes, storage and other details.
Kubota st alpha-35 tractor service repair manualfujjsekfkksekm
This document provides maintenance information for STα-30 and STα-35 tractors. It discusses general precautions for handling electrical parts and wiring, recommended lubricants and fluids, and maintenance check points to perform every 50, 100, 200, 400 hours or yearly/2-yearly. Precautions are given for safe handling of batteries, fuses, connectors and circuit testers. Wiring should be securely clamped without damage and terminals properly protected. Only specified lubricants and fuels should be used in the tractor systems.
Kubota rck72 f36 front cut ride on mower service repair manualfujjsekfkksekm
This document provides a workshop manual for F2880, F3680, RCK72-F36, RCK72R-F36, RCK60-F36, and RCK60R-F36 machines. It includes sections on identification, general precautions, handling electrical parts and wiring safely, recommended lubricants and fluids, tightening torques, maintenance checklists, inspection schedules, special tools, tire pressures, and implement limitations. Safety is emphasized, including proper handling of batteries, fuses, connectors and circuit testers. Detailed inspection procedures are given for daily, 50-hour, 100-hour, 200-hour, 400-hour, 1500-hour, 3000-hour and yearly maintenance
Kubota gr2100 ec lawnmower service repair manualfujjsekfkksekm
This document provides guidelines and specifications for maintenance tasks on a GR2100EC workshop manual. It includes:
- Identification information needed when contacting a dealer, such as serial numbers and hour meter reading.
- General precautions for disassembly/reassembly, use of special tools, electrical work, and lubrication.
- Guidelines for handling electrical parts and wiring, including batteries, fuses, connectors and circuit testing.
- Specifications for lubricants, fuel, coolant and greasing points.
- Tightening torque specifications for bolts, nuts and plugs.
Kubota gr1600 ec2 ride on mower service repair manualfujjsekfkksekm
This document provides information on identification, general precautions, handling precautions for electrical parts and wiring, lubricants, fuel and coolant, tightening torques, maintenance checklists, and special tools for a GR1600EC2 workshop manual. It identifies lubrication points and specifies lubricants, fuels, and coolants for the engine, transmission, cooling system, and other components. Precautions are outlined for safe handling of electrical parts, batteries, fuses, connectors and circuit testers. Tightening torques are provided for various screw types. Maintenance checklists specify daily, 50-hour, 100-hour and other periodic inspection points.
Steyr profi cvt 4130 tractor service repair manualfujjsekfkksekm
This document is a service manual that provides maintenance and repair information for various PROFI tractor models, including the PROFI 4110 ET, PROFI 4120 ET, PROFI 4130 ET, PROFI 6125 ET, PROFI 6140 ET, and PROFI CVT models. The manual contains sections on the engine, transmission, axle systems, hydraulics, electrical systems, and other components. It includes technical specifications, descriptions of component operation, troubleshooting information, and repair/replacement procedures.
Steyr profi cvt 4120 tractor service repair manualfujjsekfkksekm
This document is a service manual that provides maintenance and repair information for various PROFI tractor models, including the PROFI 4110 ET, PROFI 4120 ET, PROFI 4130 ET, PROFI 6125 ET, PROFI 6140 ET, and PROFI CVT models. The manual contains sections on the engine, transmission, axle systems, hydraulics, electrical systems, and other components. It includes technical specifications, descriptions of component operation, troubleshooting information, and repair procedures.
This document is a service and training manual for tractors models M9078, M9086, and M9094. It contains a table of contents listing the sections and publication numbers for various workshop manuals and how-to guides covering the engine, fuel system, electrical systems, steering systems, transmission, and hydraulic systems of the tractors. The manuals provide information on troubleshooting, maintenance, and repair for different components and systems of the tractors.
Steyr kompakt 4115 ecotech tractor service repair manual (pin zdjz16683 and a...fujjsekfkksekm
This document is a service manual for Kompakt 4075, 4085, 4095, 4105, and 4115 tractors. It contains an introduction and table of contents that outlines the major systems covered in the manual, including the engine, transmission, axles, hydraulics, steering, brakes, electrical systems, and more. Each system includes links to detailed sections that provide specifications, component locations, maintenance and repair instructions.
Steyr f4 dfe4131 tier 4b (final) engine service repair manualfujjsekfkksekm
This document contains a service manual for Tier 4B (final) engines. It includes sections on the engine, electrical systems, and safety information. The manual provides maintenance and repair instructions for technicians, with the goal of ensuring personal safety and preventing damage to equipment. It lists many engine part numbers and cautions technicians to only perform work according to the procedures in the manual using recommended tools.
Steyr cvt 6215 tractor service repair manualfujjsekfkksekm
This document is a service manual for CVT 6170, CVT 6185, CVT 6205, CVT 6215, and CVT 6230 tractors. It contains part numbers, links the tractors to their engine models, and provides a table of contents that lists the systems and components covered in each section of the manual, including the engine, transmission, axles, hydraulics, electrical systems, and more. The manual is intended to provide technical information and guidance for servicing the listed tractor models.
Steyr cvt 6195 tractor service repair manualfujjsekfkksekm
This document is a service manual for CVT6140, CVT6150, CVT6160, CVT6175, and CVT6195 tractors. It contains an introduction and safety information, as well as sections covering the engine, transmission, four-wheel drive system, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, steering, cab climate control, and electrical systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the various components.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
6. INTRODUCTION
Foreword - Important notice regarding equipment servicing
All repair and maintenance work listed in this manual must be carried out only by qualified dealership personnel,
strictly complying with the instructions given, and using, whenever possible, the special tools.
Anyone who performs repair and maintenance operations without complying with the procedures provided herein
shall be responsible for any subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional, or
local dealers, reject any responsibility for damages caused by parts and/or components not approved by the manu-
facturer, including those used for the servicing or repair of the product manufactured or marketed by the manufacturer.
In any case, no warranty is given or attributed on the product manufactured or marketed by the manufacturer in case
of damages caused by parts and/or components not approved by the manufacturer.
The manufacturer reserves the right to make improvements in design and changes in specifications at any time without
notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions, and
illustrative material herein are as accurate as known at time of publication but are subject to change without notice.
In case of questions, refer to your CNH Sales and Service Networks.
47606132 25/08/2014
3
7. INTRODUCTION
Safety rules
Personal safety
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible death or injury.
Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in-
structions. These precautions are intended for the personal safety of you and those working with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING indicates a hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation that, if not avoided, could result in machine or property damage.
Throughout this manual you will find the signal word Notice followed by special instructions to prevent machine or
property damage. The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information that clarifies steps, procedures, or other information in this manual.
Throughout this manual you will find the word Note followed by additional information about a step, procedure, or
other information in the manual. The word Note is not intended to address personal safety or property damage.
47606132 25/08/2014
4
8. INTRODUCTION
Safety rules - Ecology and the environment
Soil, air, and water are vital factors of agriculture and life in general. When legislation does not yet rule the treatment
of some of the substances required by advanced technology, sound judgment should govern the use and disposal of
products of a chemical and petrochemical nature.
NOTE: The following are recommendations that may be of assistance:
• Become acquainted with and ensure that you understand the relative legislation applicable to your country.
• Where no legislation exists, obtain information from suppliers of oils, filters, batteries, fuels, antifreeze, cleaning
agents, etc., with regard to their effect on man and nature and how to safely store, use, and dispose of these
substances.
• Agricultural consultants will, in many cases, be able to help you as well.
Helpful hints
• Avoid filling tanks using cans or inappropriate pressurized fuel delivery systems that may cause considerable
spillage.
• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of them contain substances that may be
harmful to your health.
• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when draining off used engine coolant mixtures, engine, gearbox and hydraulic oils, brake fluids, etc.
Do not mix drained brake fluids or fuels with lubricants. Store them safely until they can be disposed of in a proper
way to comply with local legislation and available resources.
• Do not allow coolant mixtures to get into the soil Collect and dispose of coolant mixtures properly.
• Do not open the air-conditioning system yourself. It contains gases that should not be released into the atmosphere.
Your CNH dealer or air conditioning specialist has a special extractor for this purpose and will have to recharge the
system properly.
• Repair any leaks or defects in the engine cooling or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding as penetrating weld splatter may burn a hole or weaken them, allowing the loss of
oils, coolant, etc.
47606132 25/08/2014
5
9. INTRODUCTION
Basic instructions - Shop and Assembly
Shimming
For each adjustment operation, select adjusting shims and measure individually using a micrometer, then add up
the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or the rated value
indicated on each shim.
Rotating shaft seals
For correct rotating shaft seal installation, proceed as follows:
• before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.
• thoroughly clean the shaft and check that the working surface on the shaft is not damaged.
• position the sealing lip facing the fluid; with hydrodynamic lips, take into consideration the shaft rotation direction
and position the grooves so that they will deviate the fluid towards the inner side of the seal.
• coat the sealing lip with a thin layer of lubricant (use oil rather than grease) and fill the gap between the sealing lip
and the dust lip on double lip seals with grease.
• insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a
hammer or mallet.
• whilst inserting the seal, check that it is perpendicular to the seat; once settled, make sure that it makes contact
with the thrust element, if required.
• to prevent damaging the seal lip on the shaft, position a protective guard during installation operations.
O-Ring seals
Lubricate the O-RING seals before inserting them in the seats, this will prevent them from overturning and twisting,
which would jeopardise sealing efficiency.
Sealing compounds
Apply one of the following sealing compounds on the mating surfaces when specified: SILMATE® RTV1473, or
LOCTITE® RTV 598™ or LOCTITE® INSTANT GASKET 587™ BLUE. Before applying the sealing compound, prepare
the surfaces as directed on product container or as follows:
• remove any incrustations using a metal brush.
• thoroughly de-grease the surfaces using a locally approved cleaning agent such as safety solvent or brake parts
cleaner.
Spare parts
Only use "CNH Original Parts" or " CNH Parts".
Only genuine spare parts guarantee the same quality, duration and safety as original parts, as they are the same
parts that are assembled during standard production. Only "CNH Original Parts" or " CNH Parts" can offer this
guarantee.
When ordering spare parts, always provide the following information:
• machine model (commercial name) and serial number
• part number of the ordered part, which can be found in the "Microfiches" or the "Service Parts Catalogue", used for
order processing
47606132 25/08/2014
14
10. INTRODUCTION
Protecting the electronic/electrical system during charging or welding
To avoid damage to the electronic/electrical systems, always observe the following:
1. Never make or break any of the charging circuit connections, including the battery connections, when the engine
is running.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the combine or on any header
attached to the combine.
• position the welder ground clamp as close to the welding area as possible
• if welding in close proximity to a computer module, then the module should be removed from the combine
• never allow welding cables to lay on, near or across any electrical wiring or electronic component while welding
is in progress
4. Always disconnect the negative cable from the battery when charging the battery in the combine with a battery
charger.
NOTICE: If welding must be performed on the unit, either the combine or the header (if it is attached), the battery
ground cable must be disconnected from the combine battery. The electronic monitoring system and charging system
will be damaged if this is not done.
Remove the battery ground cable. Reconnect the cable when welding is completed.
WARNING
Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.
W0111A
Tools
The tools that CNH suggests and illustrate in this manual have been:
• specifically researched and designed for use with CNH machines
• essential for reliable repair operations
• accurately built and rigorously tested so as to offer efficient and long-lasting operation
By using these tools, repair personnel will benefit from:
• operating in optimal technical conditions
• obtaining the best results
• saving time and effort
• working in safe conditions
NOTE: The terms "front", "rear", "right-hand" and "left-hand" (when referred to different parts) are determined from
the rear, facing in the direction of travel of the machine during operation.
47606132 25/08/2014
15
11. INTRODUCTION
Basic instructions - Shop and assembly
Shimming
For each adjustment operation, select adjusting shims and measure the adjusting shims individually using a microm-
eter, then add up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or
the rated value shown on each shim.
Rotating shaft seals
For correct rotating shaft seal installation, proceed as follows:
1. Before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.
2. Thoroughly clean the shaft and check that the working surface on the shaft is not damaged.
3. Position the sealing lip facing the fluid.
NOTE: With hydrodynamic lips, take into consideration the shaft rotation direction and position the grooves so that
they will move the fluid towards the inner side of the seal.
4. Coat the sealing lip with a thin layer of lubricant (use oil rather than grease). Fill the gap between the sealing lip
and the dust lip on double lip seals with grease.
5. Insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a
hammer or mallet.
6. While you insert the seal, check that the seal is perpendicular to the seat. When the seal settles, make sure that
the seal makes contact with the thrust element, if required.
7. To prevent damage to the seal lip on the shaft, position a protective guard during installation operations.
O-ring seals
Lubricate the O-ring seals before you insert them in the seats. This will prevent the O-ring seals from overturning and
twisting, which would jeopardize sealing efficiency.
Sealing compounds
Apply a sealing compound on the mating surfaces when specified by the procedure. Before you apply the sealing
compound, prepare the surfaces as directed by the product container.
Spare parts
Only use CNH Original Parts or CNH Original Parts.
Only genuine spare parts guarantee the same quality, duration, and safety as original parts, as they are the same
parts that are assembled during standard production. Only CNH Original Parts or CNH Original Parts can offer this
guarantee.
When ordering spare parts, always provide the following information:
• Machine model (commercial name) and Product Identification Number (PIN)
• Part number of the ordered part, which can be found in the parts catalog
47606132 25/08/2014
16
12. INTRODUCTION
Protecting the electronic and/or electrical systems during charging and welding
To avoid damage to the electronic and/or electrical systems, always observe the following practices:
1. Never make or break any of the charging circuit connections when the engine is running, including the battery
connections.
2. Never short any of the charging components to ground.
3. Always disconnect the ground cable from the battery before arc welding on the machine or on any machine
attachment.
• Position the welder ground clamp as close to the welding area as possible.
• If you weld in close proximity to a computer module, then you should remove the module from the machine.
• Never allow welding cables to lie on, near, or across any electrical wiring or electronic component while you
weld.
4. Always disconnect the negative cable from the battery when charging the battery in the machine with a battery
charger.
NOTICE: If you must weld on the unit, you must disconnect the battery ground cable from the machine battery.
The electronic monitoring system and charging system will be damaged if this is not done.
5. Remove the battery ground cable. Reconnect the cable when you complete welding.
WARNING
Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.
W0111A
Special tools
The special tools that CNH suggests and illustrate in this manual have been specifically researched and designed for
use with CNH machines. The special tools are essential for reliable repair operations. The special tools are accurately
built and rigorously tested to offer efficient and long-lasting operation.
By using these tools, repair personnel will benefit from:
• Operating in optimal technical conditions
• Obtaining the best results
• Saving time and effort
• Working in safe conditions
47606132 25/08/2014
17
18. Engine - Engine and crankcase
Engine - General specification
General specifications
Engine type 4 Cylinders 6 Cylinders
Cycle Four-Stroke diesel engine
Power Turbocharged with intercooler
Injection Direct
Number of cylinders 4 6
Bore 104 mm (4 in)
Stroke 132 mm (5 in)
Total displacement 4485 cm³ 6728 cm³
Timing
Start before T.D.C. 18.5 °
End after B.D.C. 29.5 °
Start before B.D.C. 67 °
End after T.D.C. 35 °
Valve clearance
Intake 0.20 - 0.30 mm (0.008 - 0.012 in)
Exhaust 0.45 - 0.55 mm (0.018 - 0.022 in)
Fuel feed
Injection type Bosch high pressure common rail
Control EDC17 CV41
Injector CRIN 2
Nozzle type DLLA
Injection sequence 1-3-4-2 1-5-3-6-2-4
Injection pressure 250 - 1600 bar (3625 - 23200 psi)
Aspiration
Turbocharging Intercooled
Turbocharger type Honeywell GT25 Holset HX35
Lubrication
Oil pressure @ low idle 0.7 bar (10 psi)
Oil pressure @ fast idle 3.5 bar (51 psi)
Oil pan capacity 15 l (15.85 US qt)
Oil filter capacity 1 l (1.06 US qt)
Cooling
Water pump Belt driven
Thermostat 79 - 83 °C (174 - 181 °F)
47606132 25/08/2014
10.1 [10.001] / 3
19. Engine - Engine and crankcase
Clearance data
Cylinder block and crankshaft components
Cylinder barrels 104.000 - 104.024 mm (4.094 - 4.095 in)
Oversize 0.4 mm (0.016 in)
Pistons 103.739 - 103.757 mm (4.084 - 4.085 in) (*)
Skirt height 49.5 mm (1.949 in) (*)
Pin housing 38.010 - 38.016 mm (1.496 - 1.497 in)
Piston (oversize) 0.4 mm (0.016 in)
Protrusion 0.28 - 0.52 mm (0.011 - 0.020 in)
Pin 37.994 - 38.000 mm (1.496 - 1.496 in)
Piston pin - Pin housing 0.01 - 0.022 mm (0.0004 - 0.001 in)
Piston ring landings
Combustion 2.705 - 2.735 mm (0.106 - 0.108 in)
Intermediate 2.420 - 2.440 mm (0.095 - 0.096 in) (*)
Oil control 4.030 - 4.050 mm (0.159 - 0.159 in)
Piston rings
Combustion 2.560 - 2.605 mm (0.101 - 0.103 in)
Intermediate 2.350 - 2.380 mm (0.093 - 0.094 in)
Oil control 3.970 - 3.990 mm (0.156 - 0.157 in)
Piston ring and ring landing clearance
Combustion 0.100 - 0.175 mm (0.004 - 0.007 in)
Intermediate 0.060 - 0.110 mm (0.002 - 0.004 in) / 0.040 - 0.090 mm (0.002 - 0.004 in) (*)
Oil control 0.040 - 0.080 mm (0.002 - 0.003 in)
Piston ring end gap
Combustion 0.30 - 0.40 mm (0.012 - 0.016 in)
Intermediate 0.60 - 0.80 mm (0.024 - 0.031 in)
Oil control 0.30 - 0.55 mm (0.012 - 0.022 in)
Connecting rod
Small end housing 40.987 - 41.013 mm (1.614 - 1.615 in)
Big end housing 72.987 - 73.013 mm (2.874 - 2.875 in)
Small end bushing inside
diameter
38.019 - 38.033 mm (1.497 - 1.497 in)
Big end bearing shell
thickness
1.955 - 1.968 mm (0.077 - 0.077 in)
Piston pin and bushing
clearance
0.019 - 0.039 mm (0.001 - 0.002 in)
Oversize big end bearing
shells
0.250 mm (0.010 in) ; 0.500 mm (0.020 in)
Crankshaft
Main journals 82.99 - 83.01 mm (3.267 - 3.268 in)
Crankpins 68.987 - 69.013 mm (2.716 - 2.717 in)
Main bearing shell thickness 2.456 - 2.464 mm (0.097 - 0.098 in)
Big end bearing shell
thickness
1.955 - 1.968 mm (0.077 - 0.078 in)
Main bearing bore
No. 1,5 / 1,7 87.982 - 88.008 mm (3.464 - 3.465 in)
No. 2,3,4 / 2,3,4,5,6 87.977 - 88.013 mm (3.464 - 3.465 in)
Bearing shell and journal clearance
No. 1,5 / 1,7 0.041 - 0.119 mm (0.002 - 0.005 in)
No. 2,3,4 / 2,3,4,5,6 0.041 - 0.103 mm (0.002 - 0.004 in)
Bearing shell and crankpin
clearance
0.033 - 0.041 mm (0.001 - 0.002 in)
Thrust journal 37.475 - 37.545 mm (1.475 - 1.478 in)
Thrust bearing bore 32.180 - 32.280 mm (1.267 - 1.271 in)
Thrust bearing 37.28 - 37.38 mm (1.468 - 1.472 in)
Crankshaft end play 0.095 - 0.265 mm (0.004 - 0.010 in)
47606132 25/08/2014
10.1 [10.001] / 4
20. Engine - Engine and crankcase
Clearance data
Cylinder head and components
Valve guide bore 7.042 - 7.062 mm (0.277 - 0.278 in)
Intake valves
Stem diameter 6.970 - 6.990 mm (0.274 - 0.275 in)
Face angle 59.75 - 60.25 °
Exhaust valves
Stem diameter 6.970 - 6.990 mm (0.274 - 0.275 in)
Face angle 44.75 - 44.25 °
Valve stem and guide clearance 0.052 - 0.092 mm (0.002 - 0.004 in)
Valve seat bore
Intake 34.837 - 34.863 mm (1.372 - 1.373 in)
Exhaust 34.837 - 34.863 mm (1.372 - 1.373 in)
Valve seat outside diameter:
Intake 34.917 - 34.931 mm (1.375 - 1.375 in)
Exhaust 34.917 - 34.931 mm (1.375 - 1.375 in)
Valve seat angle
Intake 60 °
Exhaust 45 °
Valve sink
Intake 0.59 - 1.11 mm (0.023 - 0.044 in)
Exhaust 0.96 - 1.48 mm (0.038 - 0.058 in)
Interference between valve seat and cylinder head
Intake 0.054 - 0.094 mm (0.002 - 0.004 in)
Exhaust 0.054 - 0.094 mm (0.002 - 0.004 in)
Valve spring height
Free 47.75 mm (1.880 in)
Under a load equal to:
330.8 - 348.8 N (74.4 -
78.4 lb)
35.33 mm (1.391 in)
Under a load equal to:
702 - 780 N (157.8 - 175.4 lb) 25.2 mm (0.992 in)
Camshaft bore
No.1 (flywheel side) 59.222 - 59.248 mm (2.332 - 2.333 in)
No. 2,3,4,5 / 2,3,4,5,6,7 54.089 - 54.139 mm (2.129 - 2.131 in)
Camshaft journals
1-5 / 1-7 53.995 - 54.045 mm (2.126 - 2.128 in)
Bushing inside diameter 54.083 - 54.147 mm (2.129 - 2.132 in)
Bushing and journal clearance 0.038 - 0.162 mm (0.001 - 0.006 in)
Cam lift
Intake 7.582 mm (0.299 in)
Exhaust 6.045 mm (0.238 in)
Tappet bore 16.000 - 16.030 mm (0.630 - 0.631 in)
Tappet outside diameter
Top 15.924 - 15.954 mm (0.627 - 0.628 in)
Middle 15.960 - 15.975 mm (0.628 - 0.629 in)
Bottom 15.924 - 15.954 mm (0.627 - 0.628 in)
Tappets and bore clearance 0.025 - 0.070 mm (0.001 - 0.003 in)
Rocker shaft 21.965 - 21.977 mm (0.865 - 0.865 in)
Rockers 22.001 - 22.027 mm (0.866 - 0.867 in)
Rockers and shaft clearance 0.024 - 0.162 mm (0.001 - 0.006 in)
47606132 25/08/2014
10.1 [10.001] / 5
22. Engine - Engine and crankcase
F4DECOMPLETE 1
The NEF F4DFE engines are turbocharged, four-stroke diesel engines with four or six cylinders and with four valves
per cylinder.
The NEF F4DFE engines have high-pressure fuel injection (common rail system). The control of the NEF F4DFE
engines is fully electronic in order to optimize the working process. The control of the NEF F4DFE engines also takes
into account the operating characteristics, the limitation of emissions and the fuel consumption as far as possible.
NOTE: Data, performance information and power are only valid if the configuration fully matches the installation guide-
lines that FPT (Fiat Powertrain Technologies) provided.
Furthermore, after an overhaul, the use of the device must correspond to the originally specified power and engine
speed for the engine.
47606132 25/08/2014
10.1 [10.001] / 7
23. Engine - Engine and crankcase
General specifications
Engine type 4 Cylinders 6 Cylinder
Cycle 4-stroke diesel
Performance Turbocharger with intercooler
Cycle Direct injection type
Number of cylinders 4 6
Bore 104 mm (4 in)
Stroke 132 mm (5 in)
Total displacement 4485 cm³ 6728 cm³
Settings for the engine control times
Start before T.D.C. 18.5 °
End after B.D.C. 29.5 °
Start after B.D.C. 67 °
End after T.D.C. 35 °
Valve clearance
intake 0.20 - 0.30 mm (0.008 - 0.012 in)
Exhaust 0.45 - 0.55 mm (0.018 - 0.022 in)
Fuel feed
Injection type Bosch high-pressure common rail
Aux. EDC7 UC31
Injector CRIN 2
Injection nozzle type DLLA
Injection order: 1-3-4-2 1-5-3-6-2-4
Injector pressure 250 - 1600 bar (3625 - 23200 psi)
Naturally
Turbocharger With intercooler
Turbocharger type Honeywell GT25 Holset HX35
Lubrication
Oil pressure at low idle 0.7 bar (10 psi)
Oil pressure at high idle 3.5 bar (51 psi)
Oil pan capacity 15 l (15.85 US qt)
Oil filter capacity 1 l (1.06 US qt)
Cooling System
Water pump Belt Driven
Thermo stat 79 - 83 °C (174 - 181 °F)
47606132 25/08/2014
10.1 [10.001] / 8
24. Engine - Engine and crankcase
Information about free play
Components of the cylinder block and components of the crankshaft
Cylinder Barrels 104.000 - 104.024 mm (4.094 - 4.095 in)
Oversize 0.4 mm (0.016 in)
piston 103.739 - 103.757 mm (4.084 - 4.085 in)
Apron height 49.5 mm (1.949 in)
Connector housing 38.010 - 38.016 mm (1.496 - 1.497 in)
Piston (oversize) 0.4 mm (0.016 in)
Protrusion 0.28 - 0.52 mm (0.011 - 0.020 in)
Piston pin 37.994 - 38.000 mm (1.496 - 1.496 in)
Piston pin – piston pin
housing
0.01 - 0.022 mm (0.0004 - 0.001 in)
Piston ring landings
Top ring 2.705 - 2.735 mm (0.106 - 0.108 in)
Mid 2.420 - 2.440 mm (0.095 - 0.096 in)
Strippers 4.030 - 4.050 mm (0.159 - 0.159 in)
Piston Rings
Top ring 2.560 - 2.605 mm (0.101 - 0.103 in)
Mid 2.350 - 2.380 mm (0.093 - 0.094 in)
Strippers 3.970 - 3.990 mm (0.156 - 0.157 in)
Clearance between the piston ring and the ring grooves
Top ring 0.100 - 0.175 mm (0.004 - 0.007 in)
Mid 0.040 - 0.090 mm (0.002 - 0.004 in)
Strippers 0.040 - 0.080 mm (0.002 - 0.003 in)
End Gap
Top ring 0.30 - 0.40 mm (0.012 - 0.016 in)
Mid 0.60 - 0.80 mm (0.024 - 0.031 in)
Strippers 0.30 - 0.55 mm (0.012 - 0.022 in)
Connecting Rods
Housing of the small end of
the connecting rod
40.987 - 41.013 mm (1.614 - 1.615 in)
Housing of the big end of the
connecting rod
72.987 - 73.013 mm (2.874 - 2.875 in)
Internal diameter of the
bushing of the small end of
the connecting rod
38.019 - 38.033 mm (1.497 - 1.497 in)
Thickness of the rod bearing
cup
1.955 - 1.968 mm (0.077 - 0.077 in)
Free play between the piston
pin and the piston bushing
0.019 - 0.039 mm (0.001 - 0.002 in)
Oversize dimension of the
rod bearing cup
0.250 mm (0.010 in); 0.500 mm (0.020 in)
Crankshaft
Main Journals 82.99 - 83.01 mm (3.267 - 3.268 in)
Crankpins 68.987 - 69.013 mm (2.716 - 2.717 in)
Thickness of the main
bearing cup
2.456 - 2.464 mm (0.097 - 0.098 in)
Thickness of the rod bearing
cup
1.955 - 1.968 mm (0.077 - 0.078 in)
Main bearing bore
Decal No. 1,5 / 1,7 87.982 - 88.008 mm (3.464 - 3.465 in)
Decal No. 2,3,4 / 2,3,4,5,6 87.977 - 88.013 mm (3.464 - 3.465 in)
Free play between the bearings and the journals
Decal No. 1,5 / 1,7 0.041 - 0.119 mm (0.002 - 0.005 in)
Decal No. 2,3,4 / 2,3,4,5,6 0.041 - 0.103 mm (0.002 - 0.004 in)
47606132 25/08/2014
10.1 [10.001] / 9
25. Engine - Engine and crankcase
Information about free play
Free play between the bearings
and the crankpins
0.033 - 0.041 mm (0.001 - 0.002 in)
Main Journals 37.475 - 37.545 mm (1.475 - 1.478 in)
Main bearing bore 32.180 - 32.280 mm (1.267 - 1.271 in)
Main bearings on the start-up
side
37.28 - 37.38 mm (1.468 - 1.472 in)
Crankshaft end play 0.095 - 0.265 mm (0.004 - 0.010 in)
Cylinder head and components
Valve guide bore 7.042 - 7.062 mm (0.277 - 0.278 in)
Intake valves
Valve stem diameter 6.970 - 6.990 mm (0.274 - 0.275 in)
Seat angle 59.75 - 60.25 °
Exhaust valves
Valve stem diameter 6.970 - 6.990 mm (0.274 - 0.275 in)
Seat angle 44.75 - 44.25 °
Free play between the valve
stem and the valve seat
0.052 - 0.092 mm (0.002 - 0.004 in)
Valve seat bore
intake 34.837 - 34.863 mm (1.372 - 1.373 in)
Exhaust 34.837 - 34.863 mm (1.372 - 1.373 in)
External diameter of the valve seat:
intake 34.917 - 34.931 mm (1.375 - 1.375 in)
Exhaust 34.917 - 34.931 mm (1.375 - 1.375 in)
Valve seat angle
intake 60 °
Exhaust 45 °
Recessing of valve
intake 0.59 - 1.11 mm (0.023 - 0.044 in)
Exhaust 0.96 - 1.48 mm (0.038 - 0.058 in)
Clearance between the valve seat ring and the cylinder head
intake 0.054 - 0.094 mm (0.002 - 0.004 in)
Exhaust 0.054 - 0.094 mm (0.002 - 0.004 in)
Valve spring length
With the spring free 47.75 mm (1.880 in)
Under a preload of:
330.8 - 348.8 N (74.4 -
78.4 lb)
35.33 mm (1.391 in)
Under a preload of:
702 - 780 N (157.8 - 175.4 lb) 25.2 mm (0.992 in)
Camshaft bore
Number 1 (flywheel side) 59.222 - 59.248 mm (2.332 - 2.333 in)
Decal No. 2,3,4,5 /
2,3,4,5,6,7
54.089 - 54.139 mm (2.129 - 2.131 in)
Camshaft journals
1-5 / 1-7 53.995 - 54.045 mm (2.126 - 2.128 in)
Internal diameter of the bearing
bushing
54.083 - 54.147 mm (2.129 - 2.132 in)
Free play between the bushing
and the bearing
0.038 - 0.162 mm (0.001 - 0.006 in)
Cam Lift
intake 7.582 mm (0.299 in)
Exhaust 6.045 mm (0.238 in)
Tappet bore 16.000 - 16.030 mm (0.630 - 0.631 in)
External diameter of the plunger
47606132 25/08/2014
10.1 [10.001] / 10
26. Engine - Engine and crankcase
Information about free play
Top 15.924 - 15.954 mm (0.627 - 0.628 in)
Mid 15.960 - 15.975 mm (0.628 - 0.629 in)
Bottom 15.924 - 15.954 mm (0.627 - 0.628 in)
Free play between the plunger
and the bore
0.025 - 0.070 mm (0.001 - 0.003 in)
Rocker shaft 21.965 - 21.977 mm (0.865 - 0.865 in)
Rockers 22.001 - 22.027 mm (0.866 - 0.867 in)
Clearance between rocker arm
and shaft
0.024 - 0.162 mm (0.001 - 0.006 in)
47606132 25/08/2014
10.1 [10.001] / 11
27. Engine - Engine and crankcase
Engine - Dynamic description
NHIL13ENG0290FA 1
The NEF F4HFA engines are characterized by four stroke diesel cycles turbocharged with 4 or 6 cylinders and 4
valves per cylinder.
They have high pressure injection fueling (common rail) and are entirely electronically driven in order to optimize the
working process in accordance to the operation, limiting pollution emissions and consumption as much as possible.
NOTE: Data, features and performance are valid only if the setter fully complies with all the installation prescriptions
provided by Fiat Power Train (FPT).
Furthermore, the use of the unit after overhaul should conform to the original specified power and engine RPM for
which the engine has been designed.
47606132 25/08/2014
10.1 [10.001] / 12
28. Engine - Engine and crankcase
Engine - Component localisation
Location of main electrical components
CRIL04D081G01 1
(1) Coolant temperature sensor (8) Fuel temperature sensor
(2) Electro injector (9) EDC17 CV41
(3) Rail pressure sensor (10) Crankshaft sensor
(4) Air temperature/Pressure sensor (11) Oil level sensor
(5) Engine starter (12) Engine oil temperature/Pressure sensor
(6) Timing sensor (13) Heating element for pre-post heating
(7) Solenoid valve for pressure regulator
The NEF F4HFE engines are fully driven by the electronic engine control module, which is assembled directly to the
engine by means of a heat exchanger enabling it's cooling, utilizing rubber buffers to reduce vibration originated by
the engine.
Through the engine control module it is possible to verify the correct working of the engine.
47606132 25/08/2014
10.1 [10.001] / 13
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
30. Engine - Engine and crankcase
Engine - Dynamic description
NHIL13ENG0291FA 1
The NEF F4DFE engines are characterized by four stroke diesel cycles turbocharged with 4 or 6 cylinders and 4
valves per cylinder.
They have high pressure injection fueling (common rail) and are entirely electronically driven in order to optimize the
working process in accordance to the operation, limiting pollution emissions and consumption as much as possible.
NOTE: Data, features and performance are valid only if the setter fully complies with all the installation prescriptions
provided by Fiat Power Train (FPT).
Furthermore, the use of the unit after overhaul should conform to the original specified power and engine RPM for
which the engine has been designed.
47606132 25/08/2014
10.1 [10.001] / 14
31. Engine - Engine and crankcase
Engine - Component localisation
Location of main electrical components
NHIL13ENG0294GA 1
(1) Coolant temperature sensor (7) fuel temperature sensor
(2) Electro-injector (8) EDC17 CV41 electronic control module
(3) Starter (9) Crankshaft speed sensor
(4) Fuel pressure sensor (10) Engine oil pressure/temperature sensor
(5) Air pressure/temperature sensor (11) Pre-post heating resistor
(6) Timing sensor
The NEF F4DFE engines are fully driven by the electronic engine control module, which is mounted remotely on the
unit utilizing rubber buffers to reduce vibration originated by the engine.
Through the engine control module it is possible to verify the correct working of the engine.
47606132 25/08/2014
10.1 [10.001] / 15
32. Engine - Engine and crankcase
Engine - Service instruction Maintenance procedures
WARNING
Chemical hazard!
When handling fuel, lubricants, and other service chemicals, follow the manufacturer's instructions.
Wear Personal Protective Equipment (PPE) as instructed. Do not smoke or use open flame. Collect
fluids in proper containers. Obey all local and environmental regulations when disposing of chemi-
cals.
Failure to comply could result in death or serious injury.
W0371A
WARNING
Escaping fluid!
Hydraulic fluid or diesel fuel leaking under pressure can penetrate the skin and cause infection or
other injury. To prevent personal injury: Relieve all pressure before disconnecting fluid lines or per-
forming work on the hydraulic system. Before applying pressure, make sure all connections are tight
and all components are in good condition. Never use your hand to check for suspected leaks under
pressure. Use a piece of cardboard or wood for this purpose. If injured by leaking fluid, see your
doctor immediately.
Failure to comply could result in death or serious injury.
W0178A
CAUTION
Burn hazard!
Hot coolant can spray out if you remove the filler cap while the system is hot. After the system has
cooled, turn the filler cap to the first notch and wait for all pressure to release before proceeding.
Failure to comply could result in minor or moderate injury.
C0043A
WARNING
Rotating parts!
The engine is running. Keep clear of rotating fans and belts.
Failure to comply could result in death or serious injury.
W0275A
Engine oil level check
The check can be made using the dipstick (1) placed on
the right hand side of the Engine Control Unit (ECU).
NOTICE: The check must be executed when the engine is
off and possibly cool.
Draw off the rod from it's slot and check that the level is
within the etched tags of minimum and maximum level.
Whether it should be difficult to make the evaluation, pro-
ceed cleaning the rod using a clean cloth with no contami-
nation and put it back in it's slot. Draw it off again and check
the level.
In case the level results being close to the tag showing min-
imum level, provide filling lubrication of the engines com-
ponents.
Add oil through the upper top or through the lateral top (2).
During filling operation, the tops must be removed as well
as the rod in order to make the oil flow easier.
NHIL13ENG1373AA 1
47606132 25/08/2014
10.1 [10.001] / 16
33. Engine - Engine and crankcase
Combustion system inspection
The check must be executed both when the engine off and
when it is running.
The check operation consists in examining the fuel
pipelines running from the tank to the pre-filter (if provided
in the specific equipment), to the filter, to the high pressure
pump and to the rail diffuser and from this last one to the
head.
Special attention must be paid to the connections on the
high pressure pipelines.
Cooling system inspection
The check must be executed both when the engine is off
and when it is running.
Check the pipelines from the engine to the radiator, from
the expansion tank and vice-versa. Find out any blow-by,
verify the status of the pipes specially close to the holding
strips.
Verify that the radiator is clean, the correct working of the
fan flywheels, the presence of any leakage from the con-
nectors, from the manifold and from the radiating unit.
The density of the cooling liquid must be checked any how
every year before winter season and be replaced in any
case every two years.
NOTE: In case of new filling, proceed bleeding the system,
through the bleeds on the engine.
If bleeding of the system is not carried out, serious inconve-
nience might be caused to the engine due to the presence
of air pockets in the engine's head.
Lubricating system inspection
The check must be executed both when the engine is off
and when it is running.
Verify the presence of any oil leakage or blow-by from the
head, from the engine pan or from the heat exchanger.
Inspection of water presence within the fuel
filter or pre-filter
The components of the common rail system can be dam-
aged very quickly in presence of water or impurity within
the fuel.
Timely proceed operating on the pre-filter (not available on
the engine block) to carry out the drainage of the water
within the feed circuit.
47606132 25/08/2014
10.1 [10.001] / 17
34. Engine - Engine and crankcase
Inspection / replacement of blow-by filter
The filter in subject has been developed and equipped for
the collection , filtering and condense of the lubricating oil
vapors.
Within the valve cover (1) is a filter (2).
Remove the cover and check the filtering element.
93110965 2
Inspection of drive belt tensioning
The drive belt tensioning control is made using an au-
tomatic tensioning device therefore no intervention is
required apart from checking the wear status of the belt
itself.
Inspection and setting of tappet clearance
Adjust clearance between rockers and valves using
setscrew wrench (1), box wrench (2) and feeler gauge (3).
Valve clearance
• Intake - 0.20 - 0.30 mm (0.008 - 0.012 in)
• Exhaust - 0.45 - 0.55 mm (0.018 - 0.022 in)
NHIL13ENG0312AA 3
Engine oil and filter replacement
Due to the several applications, the pan shape and the
oil quantity can change slightly. However, the following
operations are valid for all applications.
We recommend to carry out the oil drainage when the en-
gine is hot.
Place a proper container for the oil collecting under the pan
connected with drain plug.
Unscrew the plug and then take out the control dipstick and
the inserting plug to ease the downflow of the lubrication oil.
After the complete drainage, screw the plug and carry out
the clean oil filling.
NOTICE: Use only recommended oil or oil having the re-
quested features for the correct engine functioning. In case
of topping up, don't mix oils having different features. If you
don't comply with these rules, the service warranty is no
more valid.
Check the level through the dipstick until when the filling is
next to the maximum level notch indicated on the dipstick.
47606132 25/08/2014
10.1 [10.001] / 18