This document provides specifications for a KR-5000DEL lithium-ion cell, including:
1) The cell has a nominal capacity of 5000mAh and nominal voltage of 1.2V.
2) Standard charging current is 500mA and fast charging current is 7500mA, with standard charging time of 14-16 hours and fast charging time of about 1 hour.
3) The cell has an average internal impedance of 3.5mΩ and dimensions of 33.2 x 59.5 mm with a weight of 150g.
This document discusses selective coordination of circuit breakers. It provides:
1. An overview of circuit breaker curves and how to read them, including overload regions, instantaneous regions, unlatching times, and interrupting ratings.
2. How the instantaneous region and unlatching times make it difficult for circuit breakers to be selectively coordinated for high fault currents. Once a breaker unlatches, it will open, even if a downstream breaker clears the fault first.
3. A simplified method to check coordination without drawing full time-current curves. It involves comparing the instantaneous trip settings of breakers in series to determine which will open for different
This document provides specifications for 1N4001 through 1N4007 plastic silicon rectifier diodes. The diodes have voltage ratings from 50 to 1000 volts, current ratings up to 1 amp, and are packaged in a molded plastic DO-41 case. Key ratings and characteristics include maximum reverse voltage, forward voltage drop, surge current capability, and operating temperature range from -55 to +150 degrees Celsius. Curves show typical forward and reverse diode characteristics.
This document provides specifications for ultra-fast-recovery rectifier diodes in the FML-G12S, FML-G13S, FML-G14S, and FML-G16S series, including:
1) Absolute maximum ratings and electrical characteristics such as forward voltage, reverse current, and switching times.
2) Derating curves showing the relationship between average forward current and case temperature for each diode.
3) Typical forward voltage vs. forward current characteristics curves at different temperatures.
4) Peak forward surge current ratings and how they vary with the number of overcurrent cycles.
The document provides specifications for BTA40, BTA41, and BTB41 series 40A triacs. The triacs have a maximum RMS on-state current of 40A and voltage ratings of 600V and 800V. They are available in high power packages suitable for general purpose AC switching applications. Key features include clip assembly for superior surge current handling and an internal ceramic pad for the BTA series to provide voltage insulation.
In this presentation on Internal Thermal Resistance of LEDs we will look at the definition and significance of internal thermal resistance in LED packages, the path of heat transfer in some OSRAM LED packages, and the calculation of the junction temperature in LEDs.
This document provides information on the SX-360Z passive infrared detector ceiling mount. It has a patented multi-focus lens that provides highly dense coverage over a 360 degree, 18 meter diameter area. It can detect movement across 276 detection zones and has adjustable sensitivity and pulse count settings. The detector uses passive infrared technology and has features such as temperature compensation, noise reduction, and RF interference protection.
In this presentation on Basics of Heat Transfer we will look at the different modes of heat transfer in an LED system, thermal conductivity of typical materials used in LED system design, and the various thermal resistances involved in an LED system.
UL Certified Aluminum / Metal Core PCB for LEDs presentation. Featuring highly-respected thermal interface material basics expert Clemens Lasance of Philips Research Laboratories, the thermal management presentation is great for PWB Designers as it provides fabrication notes, material comparisons, and LED product calculators.
This document discusses selective coordination of circuit breakers. It provides:
1. An overview of circuit breaker curves and how to read them, including overload regions, instantaneous regions, unlatching times, and interrupting ratings.
2. How the instantaneous region and unlatching times make it difficult for circuit breakers to be selectively coordinated for high fault currents. Once a breaker unlatches, it will open, even if a downstream breaker clears the fault first.
3. A simplified method to check coordination without drawing full time-current curves. It involves comparing the instantaneous trip settings of breakers in series to determine which will open for different
This document provides specifications for 1N4001 through 1N4007 plastic silicon rectifier diodes. The diodes have voltage ratings from 50 to 1000 volts, current ratings up to 1 amp, and are packaged in a molded plastic DO-41 case. Key ratings and characteristics include maximum reverse voltage, forward voltage drop, surge current capability, and operating temperature range from -55 to +150 degrees Celsius. Curves show typical forward and reverse diode characteristics.
This document provides specifications for ultra-fast-recovery rectifier diodes in the FML-G12S, FML-G13S, FML-G14S, and FML-G16S series, including:
1) Absolute maximum ratings and electrical characteristics such as forward voltage, reverse current, and switching times.
2) Derating curves showing the relationship between average forward current and case temperature for each diode.
3) Typical forward voltage vs. forward current characteristics curves at different temperatures.
4) Peak forward surge current ratings and how they vary with the number of overcurrent cycles.
The document provides specifications for BTA40, BTA41, and BTB41 series 40A triacs. The triacs have a maximum RMS on-state current of 40A and voltage ratings of 600V and 800V. They are available in high power packages suitable for general purpose AC switching applications. Key features include clip assembly for superior surge current handling and an internal ceramic pad for the BTA series to provide voltage insulation.
In this presentation on Internal Thermal Resistance of LEDs we will look at the definition and significance of internal thermal resistance in LED packages, the path of heat transfer in some OSRAM LED packages, and the calculation of the junction temperature in LEDs.
This document provides information on the SX-360Z passive infrared detector ceiling mount. It has a patented multi-focus lens that provides highly dense coverage over a 360 degree, 18 meter diameter area. It can detect movement across 276 detection zones and has adjustable sensitivity and pulse count settings. The detector uses passive infrared technology and has features such as temperature compensation, noise reduction, and RF interference protection.
In this presentation on Basics of Heat Transfer we will look at the different modes of heat transfer in an LED system, thermal conductivity of typical materials used in LED system design, and the various thermal resistances involved in an LED system.
UL Certified Aluminum / Metal Core PCB for LEDs presentation. Featuring highly-respected thermal interface material basics expert Clemens Lasance of Philips Research Laboratories, the thermal management presentation is great for PWB Designers as it provides fabrication notes, material comparisons, and LED product calculators.
This document provides specifications for a nickel-metal hydride battery, model HF-B1U. The battery has a nominal voltage of 1.2V and a typical capacity of 880mAh. It can be fast charged in about 1.2 hours with a charging current of 880mA. The battery has dimensions of 17.0mm width, 6.1mm thickness, and 48.0mm height and weighs approximately 18g. Charts show the battery's voltage over time during charging and discharging.
This document provides specifications for the Marathon L2V220 lead-acid battery including:
1. Technical specifications such as rated voltage, capacity, dimensions, and weight.
2. Constant current discharge rates in amps (A) at different voltages and times ranging from 3 minutes to 20 hours.
3. Constant power discharge rates in watts per block (W/block) at different voltages and times ranging from 3 minutes to 10 hours.
4. The manufacturer and part number for ordering.
This document provides specifications for a valve-regulated lead acid battery called the LC-PD1217P. It has a nominal voltage of 12V, rated capacity of 17Ah, and expected trickle life of approximately 6 years at 25°C or 10 years at 20°C. The battery measures 181mm x 76mm x 167mm and weighs approximately 6.5kg. It has M5 bolt and nut terminals and a standard gray resin case, with an optional black resin case also available.
This document provides instructions for using the Panther7 AC Adapter and Smart Charger with LCD Display. It can charge laptop batteries independently of the laptop, power laptops and other devices, and indicates charging status on an LCD screen. The adapter has interchangeable DC connectors for over 100 laptop models and provides voltages from 5V to 22V. It has safety protections like overheating, overvoltage, overcurrent and short circuit protection.
This document provides specifications for a 6F22 E-Block rechargeable nickel-metal hydride battery with a nominal voltage of 8.4V (9V) and maximum capacity of 220mAh. The battery has standard charging at 0.1C for 14 hours and quick charging at 0.2C for 6-6.5 hours. It can be discharged at rates from 0.2C to 2.0C and operates at temperatures from -20°C to 60°C for discharge and 0°C to 45°C for charge. Graphs show the battery's voltage over time for standard and quick charging and its capacity retention over 12 months of storage.
AccuPower Charger AC Adapter: APSM800-1 Datenblatt DatasheedAkkuShop.de
The document provides specifications for the AccuPower Chargers power supply. It has an input of 100-240V AC at 50-60Hz and outputs 12-13V DC at 800mA. The DC output plug has a diameter of 2.5mm, inner diameter of 5.5mm, and is 10-12mm in length.
GP Batetry GP40AAAM Datenblatt DatasheedAkkuShop.de
This data sheet provides specifications for a rechargeable nickel metal hydride cylindrical cell battery.
1. The battery has a nominal voltage of 1.2V, capacity of 400mAh minimum and 428mAh typical, and dimensions of 10.2mm diameter and 29.2mm height.
2. It can be fast charged at rates between 0.5C to 1C (200-400mA) with charge termination control recommended, and has a service life of over 500 charge/discharge cycles.
This document provides specifications for a nickel-metal hydride battery, model HF-B1U. The battery has a nominal voltage of 1.2V and a typical capacity of 880mAh. It can be fast charged in about 1.2 hours with a charging current of 880mA. The battery has dimensions of 17.0mm width, 6.1mm thickness, and 48.0mm height and weighs approximately 18g. Charts show the battery's voltage over time during charging and discharging.
This document provides specifications for the Marathon L2V220 lead-acid battery including:
1. Technical specifications such as rated voltage, capacity, dimensions, and weight.
2. Constant current discharge rates in amps (A) at different voltages and times ranging from 3 minutes to 20 hours.
3. Constant power discharge rates in watts per block (W/block) at different voltages and times ranging from 3 minutes to 10 hours.
4. The manufacturer and part number for ordering.
This document provides specifications for a valve-regulated lead acid battery called the LC-PD1217P. It has a nominal voltage of 12V, rated capacity of 17Ah, and expected trickle life of approximately 6 years at 25°C or 10 years at 20°C. The battery measures 181mm x 76mm x 167mm and weighs approximately 6.5kg. It has M5 bolt and nut terminals and a standard gray resin case, with an optional black resin case also available.
This document provides instructions for using the Panther7 AC Adapter and Smart Charger with LCD Display. It can charge laptop batteries independently of the laptop, power laptops and other devices, and indicates charging status on an LCD screen. The adapter has interchangeable DC connectors for over 100 laptop models and provides voltages from 5V to 22V. It has safety protections like overheating, overvoltage, overcurrent and short circuit protection.
This document provides specifications for a 6F22 E-Block rechargeable nickel-metal hydride battery with a nominal voltage of 8.4V (9V) and maximum capacity of 220mAh. The battery has standard charging at 0.1C for 14 hours and quick charging at 0.2C for 6-6.5 hours. It can be discharged at rates from 0.2C to 2.0C and operates at temperatures from -20°C to 60°C for discharge and 0°C to 45°C for charge. Graphs show the battery's voltage over time for standard and quick charging and its capacity retention over 12 months of storage.
AccuPower Charger AC Adapter: APSM800-1 Datenblatt DatasheedAkkuShop.de
The document provides specifications for the AccuPower Chargers power supply. It has an input of 100-240V AC at 50-60Hz and outputs 12-13V DC at 800mA. The DC output plug has a diameter of 2.5mm, inner diameter of 5.5mm, and is 10-12mm in length.
GP Batetry GP40AAAM Datenblatt DatasheedAkkuShop.de
This data sheet provides specifications for a rechargeable nickel metal hydride cylindrical cell battery.
1. The battery has a nominal voltage of 1.2V, capacity of 400mAh minimum and 428mAh typical, and dimensions of 10.2mm diameter and 29.2mm height.
2. It can be fast charged at rates between 0.5C to 1C (200-400mA) with charge termination control recommended, and has a service life of over 500 charge/discharge cycles.