(1) This test report provides results from testing samples of a self-balancing unicycle for compliance with the RoHS directive and determination of bromine content. Testing found that samples complied with RoHS requirements for lead, cadmium, mercury and chromium. Some samples showed indications of lead and bromine. (2) A variety of samples were tested from different components of the unicycle including plastic casings, wires, screws, printed circuit boards, batteries and more. Samples were screened using XRF spectroscopy and wet chemical methods to detect regulated substances. (3) The test report concludes that the tested samples comply with the requirements of the 2011/65/EU RoHS directive.

1. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 1 of 11
Test Requested:
(1) For compliance with RoHS directive 2011/65/EU to determine the Lead, Cadmium,
Mercury, Chromium in the submitted sample.
(2) Determination of Br of the submitted sample.
Test Method:
1. Review was performed for the samples disjointed from the submitted articles and the
related test reports submitted by the applicant.
2. Tests was performed for the samples indicated by the photos in the report with test
methods reference to IEC 62321 Ed.1 111/95/2nd
CDV: Procedures for the Determination of
Levels of Six Regulated substances in Electrotechnical Products.
(1) Screening by XRF Spectroscopy.
(2) Wet Chemical Test Method
Determination of Lead & Cadmium by ICP and AAS.
Determination of Mercury by ICP.
Determination of Hexavalent Chromium by Colorimetric Method.
Determination of PBBs and PBDEs by GC/MS.
Test Results: Please refer to next page.
Conclusion:
The test result of submitted sample complies with the requirement of 2011/65/EU.
Signed for and on behalf of
Shenzhen SEM.Test Technology Co., Ltd.
Ailis Ma
PSQ Executive
Applicant : Shenzhen King Song Sports Equipment Co., Ltd.
Address :
5th
Floor, Bld. A, Taiyufeng Industry Park, Queshan Road, Dalang Street,
Longhua, Shenzhen
Products : Self-balancing Unicycle
Model/P.O NO. : KS
Receiving Date : 2015-07-30
Testing Period : 2015-07-30 to 2015-08-06
SEM.Test

2. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 2 of 11
XRF Results:
No. Name of
the sample
Part name Sample
Description
Pb
(ppm)
Cd
(ppm)
Hg
(ppm)
Cr
(ppm)
Br
(ppm)
1-1-1
Casing
parts
Shell Blue plastic BL BL BL BL BL
1-2-1 Decorate Bluerubber BL BL BL BL BL
1-3-1 Thumb
screw
Silvery metal
BL BL BL IN N.A.
1-4-1 Screw Silvery metal BL BL BL BL N.A.
1-5-1 Dust plug Red rubber BL BL BL BL BL
1-6-1 Charging
jack
Silvery Metal BL BL BL BL N.A.
1-6-2 Metal pin BL BL BL BL N.A.
1-7-1 Connector
lug
Red plastic BL BL BL BL IN
1-7-2 Copper metal BL BL BL BL N.A.
1-8-1
White wire
Black plastic BL BL BL BL BL
1-8-2 Silvery metal BL BL BL BL N.A.
1-8-3 White plastic BL BL BL BL BL
1-9-1
Switch
Silvery metal BL BL BL IN N.A.
1-9-2 White plastic BL BL BL BL BL
1-10-1
LED wire
Red Wire BL BL BL BL BL
1-10-2 Black wire BL BL BL BL BL
1-10-3 Green wire BL BL BL BL BL
1-10-4 Yellow wire BL BL BL BL BL
1-10-5 White wire BL BL BL BL BL
1-10-6 Silvery metal BL BL BL BL N.A.
1-11-1 LED gum
cover
White rubber
BL BL BL BL BL
1-12-1
LED
Body BL BL BL BL BL
1-12-2 Silvery metal BL BL BL BL N.A.
1-13-1
LED PCB
Silvery metal BL BL BL BL N.A.
1-13-2 Green PCB BL BL BL BL IN
1-14-1 Wire contact White plastic BL BL BL BL BL
1-15-1 Indicator
light
Body BL BL BL BL BL
1-15-2 Silvery metal BL BL BL BL N.A.
1-16-1
Output
Silvery metal BL BL BL BL N.A.
1-16-2 Copper metal BL BL BL BL N.A.
1-16-3 Gray plastic BL BL BL BL BL
1-16-4 Black plastic BL BL BL BL BL
1-17-1 Honey
grader
Copper metal BL BL BL BL N.A.
1-17-2 White shell BL BL BL BL N.A.
SEM.Test

3. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 3 of 11
No. Name of
the sample
Part name Sample
Description
Pb
(ppm)
Cd
(ppm)
Hg
(ppm)
Cr
(ppm)
Br
(ppm)
1-18-1
Casing
parts
Honey
grader wire
Red wire BL BL BL BL BL
1-18-2 Black wire BL BL BL BL BL
1-18-3 Copper metal BL BL BL BL N.A.
1-19-1 Honey
grader
Rubber
Black rubber
BL BL BL BL BL
1-20-1
Fine line
Red wire BL BL BL BL BL
1-20-2 Black wire BL BL BL BL BL
1-20-3 Copper metal BL BL BL BL N.A.
1-21-1 Inductance
coil
Copper metal BL BL BL BL N.A.
1-21-2 Body BL BL BL BL BL
1-22-1 Honey
grade PCB
Silvery metal BL BL BL BL N.A.
1-22-2 Green PCB BL BL BL BL N.A.
2-1-1
Loudspea
ker
Shell
Black metal BL BL BL BL N.A.
2-1-2 Blue plastic BL BL BL BL BL
2-2-1 Rubber mat Black rubber BL BL BL BL BL
2-3-1 Soldering tin Silvery metal IN BL BL BL N.A.
2-4-1 Vibrating
diaphragm
Black plastic BL BL BL BL BL
2-4-2 Copper
plastic
BL BL BL BL BL
2-5-1 Copper
metal
Copper metal
BL BL BL BL N.A.
2-6-1 Magnet Silvery metal BL BL BL BL N.A.
2-7-1 Paper Yellow paper BL BL BL BL BL
3-1-1
Power
PCB
Heat shrink
tubing
Black plastic
BL BL BL BL BL
3-2-1
Wire
Red wire BL BL BL BL BL
3-2-2 Black wire BL BL BL BL BL
3-2-3 Copper metal BL BL BL BL N.A.
3-3-1
Wire socket
White plastic BL BL BL BL BL
3-3-2 Silvery metal BL BL BL BL N.A.
3-4-1 Relay Shell Black metal BL BL BL BL N.A.
3-5-1 Relay
rubber
Black rubber
BL BL BL BL BL
3-6-1
Relay
transformer
Yellow plastic BL BL BL BL BL
3-6-2 Black plastic BL BL BL BL BL
3-6-3 Copper metal BL BL BL BL N.A.
3-7-1 Inductance Copper metal IN BL BL BL N.A.
SEM.Test

4. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 4 of 11
No. Name of
the sample
Part name Sample
Description
Pb
(ppm)
Cd
(ppm)
Hg
(ppm)
Cr
(ppm)
Br
(ppm)
3-7-2 5R6 Body BL BL BL BL BL
3-8-1 Tantalum
capacitor
476C
Silvery metal BL BL BL BL N.A.
3-8-2
Body
BL BL BL BL BL
3-9-1 Metal pin Silvery metal BL IN BL BL N.A.
3-10-1
Audion
Black plastic BL BL BL BL BL
3-10-2 Silvery metal BL BL BL BL N.A.
3-11-1
IC 356T
Black plastic BL BL BL BL BL
3-11-2 Silvery metal BL BL BL BL N.A.
3-12-1
IC 2843B
Black plastic BL BL BL BL BL
3-12-2 Silvery metal BL BL BL BL N.A.
3-13-1
SMD
Silvery metal BL BL BL BL N.A.
3-13-2 Body BL BL BL BL BL
3-14-1
Relay PCB
Silvery metal IN BL BL BL N.A.
3-14-2 Green PCB BL BL BL BL BL
4-1-1
PCB
Screw
Silvery metal BL IN BL BL N.A.
4-1-2 White plastic BL BL BL BL BL
4-2-1 Screw Metal Silvery metal BL BL BL BL N.A.
4-3-1 Heat sink Silvery metal BL BL BL BL N.A.
4-4-1 Insulation
paste
Purple plastic
BL BL BL BL BL
4-5-1 Audion
P75NF75
Silvery metal BL BL BL BL N.A.
4-5-2 Black plastic BL BL BL BL BL
4-6-1
Pins Audion
Silvery metal BL BL BL BL N.A.
4-6-2 Black plastic BL BL BL BL BL
4-7-1 Capacitance
220uF25V
Body BL BL BL BL BL
4-7-2 Silvery metal BL BL BL BL N.A.
4-8-1 Capacitance
220uF100V
Body BL BL BL BL BL
4-8-2 Silvery metal BL BL BL BL N.A.
4-9-1 Capacitance
47uF50V
Body BL BL BL BL BL
4-9-2 Silvery metal BL BL BL BL N.A.
4-10-1
Diode
Silvery metal BL BL BL BL N.A.
4-10-2 Black plastic BL BL BL BL BL
4-11-1
IC AMS1117
Silvery metal BL BL BL BL N.A.
4-11-2 Black plastic BL BL BL BL BL
4-12-1
IC 6050
Silvery metal BL BL BL BL N.A.
4-12-2 Black plastic BL BL BL BL BL
4-13-1 IC STM32 Silvery metal BL BL BL BL N.A.
SEM.Test

5. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 5 of 11
No. Name of
the sample
Part name Sample
Description
Pb
(ppm)
Cd
(ppm)
Hg
(ppm)
Cr
(ppm)
Br
(ppm)
4-13-2 Black plastic BL BL BL BL BL
4-14-1
IC 78M05
Silvery metal BL BL BL BL N.A.
4-14-2 Black plastic BL BL BL BL BL
4-15-1
IC EL817
Silvery metal BL BL BL BL N.A.
4-15-2 Black plastic BL BL BL BL BL
4-16-1
SMD
Silvery metal BL BL BL BL N.A.
4-16-2 Body BL BL BL BL BL
4-17-1
Wire socket
White plastic BL BL BL BL BL
4-17-2 Silvery metal BL BL BL BL N.A.
4-18-1 Wire
bayonet
Silvery metal
BL BL BL BL N.A.
4-19-1
Fine line
Red wire BL BL BL BL BL
4-19-2 Black wire BL BL BL BL BL
4-19-3 Copper metal BL BL BL BL N.A.
4-20-1
Heavy
gauge wire
Red wire BL BL BL BL BL
4-20-2 Black wire BL BL BL BL BL
4-20-3 Green wire BL BL BL BL BL
4-20-4 Blue wire BL BL BL BL BL
5-20-5 Purple wire BL BL BL BL BL
5-20-6 Silvery metal BL BL BL BL N.A.
4-21-1
PCB
PCB Screw Silvery metal BL BL BL BL N.A.
4-22-1
Capacitance
Silvery metal BL BL BL BL N.A.
4-22-2 Body BL BL BL BL BL
4-23-1 Heat shrink
tubing
Black plastic
BL BL BL BL BL
4-24-1 Soldering tin Silvery metal IN BL BL BL N.A.
4-25-1 PCB PCB BL BL BL BL BL
5-1-1
Battery
Rubber mat Black rubber BL BL BL BL BL
5-2-1
Connector
Silvery metal BL BL BL BL N.A.
5-2-2 Yellow plastic BL BL BL BL BL
5-2-3 Red plastic BL BL BL BL BL
5-3-1 Gummed
paper
Blue paper
BL BL BL BL BL
5-4-1 Insulating
plate
Brown plastic
BL BL BL BL N.A.
5-5-1 Positive pole Silvery metal BL BL BL BL N.A.
5-6-1 Negative
pole
Silvery metal
BL BL BL BL N.A.
SEM.Test

6. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 6 of 11
No. Name of
the sample
Part name Sample
Description
Pb
(ppm)
Cd
(ppm)
Hg
(ppm)
Cr
(ppm)
Br
(ppm)
5-7-1 Tags White paper BL BL BL BL BL
5-8-1 Insulation
paper
Green paper
BL BL BL BL BL
5-9-1 Cooling fin Silvery metal BL BL BL BL N.A.
5-10-1 Screw Silvery metal BL BL BL BL N.A.
5-11-1 Nut Silvery metal BL BL BL BL N.A.
5-12-1
IC SH3870
Silvery metal BL BL BL BL N.A.
5-12-2 Black plastic BL BL BL BL BL
5-13-1
SMD
Silvery metal BL BL BL BL N.A.
5-13-2 Body BL BL BL BL BL
5-14-1 Audion
RU1H140R
Silvery metal BL BL BL BL N.A.
5-14-2 Black plastic BL BL BL BL BL
5-15-1
Diode
Silvery metal BL BL BL BL N.A.
5-15-2 Black plastic BL BL BL BL BL
5-16-1 Soldering tin Silvery metal BL BL BL BL N.A.
5-17-1 PCB PCB BL BL BL BL BL
6-1-1
Tire part
Footboard Silvery metal BL BL BL BL N.A.
6-2-1 Dead plate Silvery metal BL BL BL BL N.A.
6-3-1 Metal rims Silvery metal BL BL BL BL N.A.
6-4-1 Metal cover Black metal BL BL BL BL N.A.
6-5-1 Tyre Black rubber BL BL BL BL BL
6-6-1 Inner tube Rubber BL BL BL BL BL
6-7-1 Copper wire Copper metal BL BL BL BL N.A.
6-8-1 Screw Silvery metal BL BL BL BL N.A.
6-9-1 Set Screws Silvery metal BL BL BL BL N.A.
6-10-1
Nut
Silvery metal BL BL BL BL N.A.
6-10-2 Metal rim BL BL BL BL N.A.
6-11-1 Metal bar Silvery metal BL BL BL BL N.A.
6-12-1
Wire
Green wire BL BL BL BL BL
6-12-2 Black wire BL BL BL BL BL
6-12-3 Red wire BL BL BL BL BL
6-12-4 Yellow wire BL BL BL BL BL
6-12-5 White wire BL BL BL BL BL
6-12-6 Copper metal BL BL BL BL N.A.
6-13-1 Wire sheath Black plastic BL BL BL BL BL
6-14-1 Horn
Coupling
White plastic BL BL BL BL BL
6-14-2 Green plastic BL BL BL BL BL
6-15-1 Soldering tin Silvery metal BL BL BL BL N.A.
SEM.Test

7. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 7 of 11
No. Name of
the sample
Part name Sample
Description
Pb
(ppm)
Cd
(ppm)
Hg
(ppm)
Cr
(ppm)
Br
(ppm)
6-16-1 Heat shrink
tubing
Black plastic
BL BL BL BL BL
6-17-1
Guide line
Yellow wire BL BL BL BL BL
6-17-2 Green wire BL BL BL BL BL
6-17-3 Blue wire BL BL BL BL BL
6-17-4 Copper metal BL BL BL BL N.A.
6-18-1 Insulating
bush
White plastic
BL BL BL BL BL
NOTE:
- ppm=mg/kg=parts per million -BL=Below limit - N.A.=Not Analysis
- IN= Inconclusive, chemical analysis necessary
Testing results are only used for reference.
Test Results:
Flame Retardants MDL Law Limit
Result(ppm)
1-7-1 1-13-2
Polybrominated Biphenyls (Mono- Deca)(PBBs) --- --- --- ---
Monobromobiphenyl 5ppm
1000ppm
N.D. N.D.
Dibromobiphenyl 5ppm N.D. N.D.
Tribromobiphenyl 5ppm N.D. N.D.
Tetrabromobiphenyl 5ppm N.D. N.D.
Pentabromobiphenyl 5ppm N.D. N.D.
Hexabromobiphenyl 5ppm N.D. N.D.
Heptabromobiphenyl 5ppm N.D. N.D.
Octabromobiphenyl 5ppm N.D. N.D.
Nonabromobiphenyl 5ppm N.D. N.D.
SEM.Test

8. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 8 of 11
Decabromobiphenyl 5ppm N.D. N.D.
Polybrominated Diphenylethers (Mono - Deca)
(PBDEs)
--- --- --- ---
Monobromobiphenyl ether 5ppm
1000ppm
N.D. N.D.
Dibromobiphenyl ether 5ppm N.D. N.D.
Tribromobiphenyl ether 5ppm N.D. N.D.
Tetrabromobiphenyl ether 5ppm N.D. N.D.
Pentabromobiphenyl ether 5ppm N.D. N.D.
Hexabromobiphenyl ether 5ppm N.D. N.D.
Heptabromobiphenyl ether 5ppm N.D. N.D.
Octabromobiphenyl ether 5ppm N.D. N.D.
Nonabromobiphenyl ether 5ppm N.D. N.D.
Decabromobiphenyl ether 5ppm N.D. N.D.
Cd MDL Law Limit
Result(ppm)
3-9-1 4-1-1
Cd 2ppm 100ppm N.D. N.D.
Cr MDL Law Limit
Result(ppm)
1-3-1 1-9-1
Cr 2ppm 1000ppm N.D. N.D.
Pb MDL Law Limit
Result(ppm)
2-3-1 3-7-1
Pb 2ppm 1000ppm N.D. N.D.
Pb MDL Law Limit
Result(ppm)
3-14-1 4-24-1
Pb 2ppm 1000ppm N.D. N.D.
SEM.Test

9. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 9 of 11
Note:
1. ppm=mg/kg
2. N.D.=Not Detected (Not detected is reported when the reading is less than detection limit value.)
3. Negative=absence of Cr(VI) in the metallic sample
Positive= presence of Cr(VI) in the metallic sample
(The tested sample should further verifie by boiling-water-extraction method if the spot test result
cannot be confirmed)
Boiling-water-ectraction:
Negative=absence of Cr(VI) in the metallic sample
Positive=presence of Cr(VI) in the metallic sample
Boiling-water-extraction solution is equal or greater that 0.02mg/kg with 50cm2
sample surface area.
4. #=Positive indicates the presence of Cr(VI) on the tested areas and result the regarded as not
comply with RoHS requirement.
Negative indicates the presence of Cr(VI) on the tested areas and result the regarded as comply with
RoHS requirement
5. MDL=Method Detection Limit
Remark:
(1) (a) It is the result on total Br while test item on restricted substances is PBBs/PBDEs. It is the result
on total Cr while test item on restricted substances is Cr6+
.
(b) Results are obtained by EDXRF for primary screening, and further chemical testing by ICP(for
Cd, Pb, Hg), UV-VIS(for CrVI) and GCMSD (for PBBs, PBDEs) is recommended to be performed. If
the concentration exceeds the below warning value according to IEC 62321 Ed.1 111/95/2nd
CDV (unit:
mg/kg)
Element Polymer Metal Composite Materials
Cd BL≤(70-3σ)<X<(130+3σ)
≤OL
BL≤(70-3σ)<X<(130+3σ)
≤OL
LOD<X<(150+3σ) ≤OL
Pb BL≤(700-3σ)<X<(1300+3σ)
≤OL
BL≤(700-3σ)<X<(1300+3σ)
≤OL
BL≤(500-3σ)<X<(1500+3σ)
≤OL
Hg BL≤(700-3σ)<X<(1300+3σ)
≤OL
BL≤(700-3σ)<X<(1300+3σ)
≤OL
BL≤(500-3σ)<X<(1500+3σ)
≤OL
Br BL≤(300-3σ)<X --- BL≤(250-3σ)<X
Cr BL≤(700-3σ)<X BL≤(700-3σ)<X BL≤(500-3σ)<X
(c) OL=Over Limit, BL=Below Limit. LOD=limit of Detection, ---=not conducted.
(d) The XRF screening test for RoHS elements- The reading may be different to the actual content
in the sample be of non-uniformity composition.
SEM.Test

10. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 10 of 11
(2) (a)mg/kg=ppm=0.0001%, N.D.=not detected(<MDL),
(b)Unit and Method Detection Limit(MDL) in wet chemical test.
Test Items Pb Cd Hg
Units Mg/kg Mg/kg Mg/kg
MDL 2 2 2
The MDL for single compound of PBBs & PBDEs is 5mg/kg and MDL of Cr6+
for polymer & composite
sample is 2mg/kg.
(c) According to IEC 62321 Ed.1 111/95/2nd
CDV, result on Cr6+
for metal sample is shown as
Positive/Negative.
Negative=Absence of Cr6
+ coating, Positive= Persence of Cr6+
coating.
(d)According to 2005/717/EC, DecaBDE is exempt.
SEM.Test

11. TEST REPORT
Shenzhen SEM.Test Technology Co., Ltd.
1/F, Building A, Hongwei Industrial Park, Liuxian 2nd Road, Bao'an District, Shenzhen, P.R.C. (518101)
Report No.: STRD1507048R
This Test Report is issued by the Company subject to its General Conditions of Service printed overleaf. Attention is drawn to
the limitations of liability, indemnification and jurisdictional policies defined therein. The results shown in this test report refer
only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. This Test Report cannot
be reproduced, except in full, without prior written permission of the Company.
Page 11 of 11
PHOTOS:
*********************End of Report *********************
SEM.Test