Remove the cooling package housing wrapper bolts and carefully lift and remove the cooling package housing wrapper. Label and disconnect any hoses or tubes leading to components attached to the cooling package. Support the cooling package and disconnect any remaining hoses or tubes to fully separate the cooling package.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ufjkskemfseol
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, hydraulic, and transmission lines.
2. Removing brackets and supports around the engine.
3. Lifting out the cooling package housing wrapper to access the engine.
The summary outlines the major preparatory steps for removing the engine by disconnecting ancillary systems and supports.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...fhjsekfksemert
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, transmission oil, and hydraulic oil lines.
2. Removing brackets and supports for components attached to the engine like the air intake, cooling package wrapper, and horn.
3. Labeling and disconnecting hydraulic hoses to the hydraulic oil cooler and transmission oil cooler hoses.
4. Supporting the cooling package and removing bolts holding it in place.
5. Carefully lifting and removing the cooling package housing wrapper to expose the engine.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ujdjfjkskmdm
This document is a service manual for a U80C Tier 4 Tractor Backhoe from PIN NCC570800. It contains information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules are provided at the beginning regarding proper operation, maintenance, and repair of the machine.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ujfdjjkskkdme
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, hydraulic, and transmission lines.
2. Removing brackets and supports around the engine.
3. Lifting out the cooling package housing wrapper to access the engine.
The summary outlines the major preparatory steps for safely removing the engine according to the service manual.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...fujsjfskekmm
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, transmission oil, and hydraulic oil lines.
2. Removing brackets and supports for components attached to the engine like the air intake, cooling package, and horn.
3. Lifting and removing the cooling package housing to access the engine.
The process prepares the engine for removal by disconnecting all attached components and lines in a careful sequence.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...fusjefjskefkksem
This document is a service manual for a U80C Tier 4 Tractor Backhoe from PIN NCC570800. It contains information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules are provided at the beginning regarding proper operation, maintenance, and repair of the machine.
CASE 570NXT Tier 4 Tractor Loader Service Repair Manual (From PIN NCC570600).pdfufhjsekdmmdm
This document is the service manual for the 570NXT Tier 4 Tractor Loader from PIN NCC570600. It contains safety instructions, an introduction, and detailed sections on the engine, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, cab climate control, electrical systems, front loader, platform/bodywork, and fault codes. Users are advised to read the operator's manual and safety manual before servicing the machine and follow all safety procedures, using only recommended fluids and filters, and not modifying cast ductile iron parts.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ufjkskemfseol
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, hydraulic, and transmission lines.
2. Removing brackets and supports around the engine.
3. Lifting out the cooling package housing wrapper to access the engine.
The summary outlines the major preparatory steps for removing the engine by disconnecting ancillary systems and supports.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...fhjsekfksemert
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, transmission oil, and hydraulic oil lines.
2. Removing brackets and supports for components attached to the engine like the air intake, cooling package wrapper, and horn.
3. Labeling and disconnecting hydraulic hoses to the hydraulic oil cooler and transmission oil cooler hoses.
4. Supporting the cooling package and removing bolts holding it in place.
5. Carefully lifting and removing the cooling package housing wrapper to expose the engine.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ujdjfjkskmdm
This document is a service manual for a U80C Tier 4 Tractor Backhoe from PIN NCC570800. It contains information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules are provided at the beginning regarding proper operation, maintenance, and repair of the machine.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...ujfdjjkskkdme
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, hydraulic, and transmission lines.
2. Removing brackets and supports around the engine.
3. Lifting out the cooling package housing wrapper to access the engine.
The summary outlines the major preparatory steps for safely removing the engine according to the service manual.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...fujsjfskekmm
The document provides a service manual for removing an engine from a tractor. Key steps include:
1. Disconnecting hoses and lines from the engine including fuel, coolant, transmission oil, and hydraulic oil lines.
2. Removing brackets and supports for components attached to the engine like the air intake, cooling package, and horn.
3. Lifting and removing the cooling package housing to access the engine.
The process prepares the engine for removal by disconnecting all attached components and lines in a careful sequence.
New holland u80 c tier 4 tractor backhoe service repair manual (from pin ncc5...fusjefjskefkksem
This document is a service manual for a U80C Tier 4 Tractor Backhoe from PIN NCC570800. It contains information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, hitches and drawbars, frames and ballasting, steering, wheels, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety rules are provided at the beginning regarding proper operation, maintenance, and repair of the machine.
CASE 570NXT Tier 4 Tractor Loader Service Repair Manual (From PIN NCC570600).pdfufhjsekdmmdm
This document is the service manual for the 570NXT Tier 4 Tractor Loader from PIN NCC570600. It contains safety instructions, an introduction, and detailed sections on the engine, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, cab climate control, electrical systems, front loader, platform/bodywork, and fault codes. Users are advised to read the operator's manual and safety manual before servicing the machine and follow all safety procedures, using only recommended fluids and filters, and not modifying cast ductile iron parts.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fusjejksekfmm
- The document provides service information for removing the engine from a 570NXT tractor, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting A/C and fuel lines, removing the horn bracket, lifting off the cooling package housing wrapper, and disconnecting hydraulic, transmission, and other hoses.
- Proper preparation is required such as draining fluids and disconnecting batteries before removing the engine.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)hfjsjekfksmem
This document is the service manual for the 570NXT Tier 4 Tractor Loader from PIN NCC570600. It contains safety instructions, an introduction, and detailed sections on the engine, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, cab climate control, electrical systems, front loader, platform/bodywork, and fault codes. Users are advised to read the operator's manual and safety manual before servicing the machine and follow all safety procedures, using only recommended fluids and filters. Unauthorized modifications could be dangerous.
Case 570 nxt tier 4 tractor loader service repair manual instant download (fr...uufsjkefkksemm
- The document provides service information for removing the engine from a 570NXT tractor, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting air conditioning lines, fuel lines, and transmission oil cooler hoses.
- The cooling package housing wrapper is then removed to allow lifting out the engine. All disconnected components are first labeled and placed out of the way.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fujjsefksekmem
- The document provides service information for removing the engine from a 570NXT tractor loader, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting air conditioning and fuel lines, removing the horn bracket, and lifting away the cooling package housing wrapper after disconnecting hoses and bolts.
- Additional components disconnected are the air intake tube, lower radiator hose, and transmission oil cooler hoses from the engine.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fusjejfskekfmsme
- The document provides service information for removing the engine from a 570NXT tractor, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting A/C and fuel lines, removing the horn bracket, lifting off the cooling package housing wrapper, and disconnecting hydraulic, transmission, and other hoses from the engine.
- Proper preparation is required such as draining fluids and disconnecting batteries before removing the engine.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fjjsekksekmm
This document provides instructions for removing the engine from a 570NXT tractor. The steps include:
- Removing the air intake tube support bracket
- Disconnecting various coolant and fuel lines
- Removing the horn bracket and placing components away from the cooling package
- Loosening and removing the receiver/dryer hold-down clamps
- Supporting and removing the cooling package housing wrapper bolts
- Carefully lifting and removing the cooling package housing wrapper
- Labeling and disconnecting hydraulic oil hoses to the hydraulic oil cooler
- Disconnecting the air intake tube from the air cleaner
CASE IH 420 Cotton Picker Service Repair Manual Instant Download.pdfgongyi2122252
This document provides service information for removing and installing the engine on a Case IH 420 Cotton Express cotton picker. It outlines the necessary special tools, describes how to raise the cotton basket if needed to access the engine, and provides step-by-step instructions for removing and installing the engine safely. Safety precautions are emphasized, and all removed hardware should be retained for reinstallation.
CASE IH 420 Cotton Picker Service Repair Manual Instant Download.pdfnaoji181714047
This document provides service information for removing and installing the engine on a Case IH 420 Cotton Express cotton picker. It outlines the necessary special tools, describes how to raise the cotton basket if needed to access the engine, and provides step-by-step instructions for removing and installing the engine safely. Safety precautions are emphasized, and all removed hardware should be retained for reinstallation.
CASE IH 420 Cotton Picker Service Repair Manual Instant Download.pdfsang1818141471
This document provides service information for removing and installing the engine on a Case IH 420 Cotton Express cotton picker. It outlines the necessary special tools, describes how to raise the cotton basket if needed to access the engine, and provides step-by-step instructions for removing and installing the engine safely. Safety precautions are emphasized, and all removed hardware should be retained for reinstallation.
New Holland T5.115 Electro Command Tractor Service Repair Manual.pdff8seujdjkddm
1. Refit belts on alternator and compressor. Reposition compressor and belt.
2. Apply sealing compound and reconnect engine to gearbox. Secure with bolts.
3. Reconnect wiring harnesses, sensors, pipes, filters and other components.
4. Refit starter motor, battery cables and guards. Reconnect hydraulic and cooling lines.
5. Reinstall air cleaner, exhaust, brackets and other ancillary components. Apply torque settings.
New Holland T5.115 Tractor Service Repair Manual.pdff8seujdjkddm
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. The engines are 4-cylinder, turbocharged diesel engines with direct fuel injection that produce between 99 and 114 horsepower.
New Holland T5.95 Tractor Service Repair Manual.pdff8seujdjkddm
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines across various operating parameters.
New Holland T5.105 Tractor Service Repair Manual.pdff8seujdjkddm
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines across various operating parameters.
New Holland T5.105 Electro Command Tractor Service Repair Manual.pdff8seujdjkddm
1. Refit belts on alternator and compressor pulley and adjust tension.
2. Reposition compressor and belt, ensuring belt is seated in all pulleys.
3. Apply sealing compound and reconnect engine to gearbox.
4. Reconnect all wiring harnesses, hoses, lines, and sensors to the engine.
5. Refit components like the starter motor, battery, filters, and brackets.
6. Check all fasteners and fluid levels after installation is complete.
New Holland T5.95 Electro Command Tractor Service Repair Manual.pdff8seujdjkddm
1. Refit belts on alternator and compressor pulley and adjust tension.
2. Reposition compressor and belt, ensuring belt is seated in all pulleys.
3. Apply sealing compound and install engine/front axle assembly to gearbox, turning crankshaft for alignment.
4. Reconnect all wiring harnesses, hoses, lines, and sensors to the engine and surrounding components.
New Holland LW110B Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides instructions for removing and installing an engine and radiator on a New Holland Construction LW 110.B wheel loader. The 3-step process includes: 1) preparing the machine by lowering attachments, releasing pressures, and disconnecting batteries; 2) attaching lifting devices to the engine compartment and removing panels; and 3) removing engine and radiator components and installing the new engine.
New Holland W300C Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for CNH Italia S.p.A. wheel loaders models W270C and W300C. It contains instructions and specifications for servicing and repairing components of the wheel loaders. The manual is divided into tabs covering general information, engines, fuel system, electrical systems, steering, powertrain, brakes, hydraulics, and mounted equipment. The document provided is the table of contents, which lists each section number and title. It does not contain any repair or service instructions.
New Holland W230C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides instructions for removing the engine from a wheel loader. It involves marking components for reinstallation, draining fluids like coolant and oil, disconnecting batteries, and using lifting straps to remove the engine. Removal requires proper safety procedures and draining of hydraulic pressure before disconnecting hoses and electrical connections.
New Holland W270C Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for CNH Italia S.p.A. wheel loaders models W270C and W300C. It contains instructions and specifications for servicing and repairing components of the wheel loaders. The manual is divided into tabs covering general information, engines, fuel system, electrical systems, steering, powertrain, brakes, hydraulics, and mounted equipment. The document provides an index of sections for each component system and instructions for tasks like removing and installing engines, radiators, transmissions, hydraulic pumps and more. Safety practices and torque specifications are also included.
New Holland W300C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for a wheel loader that provides specifications and repair instructions. It contains sections on the engine, transmission, drivetrain, brakes, hydraulics, frames, steering, wheels, cab controls, electrical systems, attachments, and other components. Tables provide torque specifications for fasteners in decimal, metric, and hydraulic fitting sections.
New Holland W270C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for a wheel loader that provides specifications and repair instructions. It contains sections on the engine, transmission, drivetrain, brakes, hydraulics, frames, steering, wheels, cab controls, electrical systems, attachments, and bodywork. The introduction provides conversion tables between metric and imperial units as well as torque specifications for fasteners.
New Holland W190C Tier 4A (interim) Wheel Loader Service Repair Manual.pdff8seujdjkddm
This service manual provides specifications and repair information for Tier 4A interim wheel loaders. It covers the engine, transmission, four-wheel drive system, front and rear axle systems, brakes, hydraulic systems, frames, steering, wheels, cab climate control, electrical systems, front loader, bucket, cab, and decals. The manual includes an introduction on safety rules and product identification.
More Related Content
Similar to New Holland U80C Tier 4 Tractor Backhoe Service Repair Manual (From PIN NCC570800).pdf
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fusjejksekfmm
- The document provides service information for removing the engine from a 570NXT tractor, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting A/C and fuel lines, removing the horn bracket, lifting off the cooling package housing wrapper, and disconnecting hydraulic, transmission, and other hoses.
- Proper preparation is required such as draining fluids and disconnecting batteries before removing the engine.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)hfjsjekfksmem
This document is the service manual for the 570NXT Tier 4 Tractor Loader from PIN NCC570600. It contains safety instructions, an introduction, and detailed sections on the engine, transmission, axles, brakes, hydraulics, hitches, frames, steering, wheels, cab climate control, electrical systems, front loader, platform/bodywork, and fault codes. Users are advised to read the operator's manual and safety manual before servicing the machine and follow all safety procedures, using only recommended fluids and filters. Unauthorized modifications could be dangerous.
Case 570 nxt tier 4 tractor loader service repair manual instant download (fr...uufsjkefkksemm
- The document provides service information for removing the engine from a 570NXT tractor, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting air conditioning lines, fuel lines, and transmission oil cooler hoses.
- The cooling package housing wrapper is then removed to allow lifting out the engine. All disconnected components are first labeled and placed out of the way.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fujjsefksekmem
- The document provides service information for removing the engine from a 570NXT tractor loader, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting air conditioning and fuel lines, removing the horn bracket, and lifting away the cooling package housing wrapper after disconnecting hoses and bolts.
- Additional components disconnected are the air intake tube, lower radiator hose, and transmission oil cooler hoses from the engine.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fusjejfskekfmsme
- The document provides service information for removing the engine from a 570NXT tractor, including disconnecting hoses, brackets, and other components from the engine and cooling package.
- Steps include removing the air intake tube support bracket, disconnecting A/C and fuel lines, removing the horn bracket, lifting off the cooling package housing wrapper, and disconnecting hydraulic, transmission, and other hoses from the engine.
- Proper preparation is required such as draining fluids and disconnecting batteries before removing the engine.
Case 570 nxt tier 4 tractor loader service repair manual (from pin ncc570600)fjjsekksekmm
This document provides instructions for removing the engine from a 570NXT tractor. The steps include:
- Removing the air intake tube support bracket
- Disconnecting various coolant and fuel lines
- Removing the horn bracket and placing components away from the cooling package
- Loosening and removing the receiver/dryer hold-down clamps
- Supporting and removing the cooling package housing wrapper bolts
- Carefully lifting and removing the cooling package housing wrapper
- Labeling and disconnecting hydraulic oil hoses to the hydraulic oil cooler
- Disconnecting the air intake tube from the air cleaner
CASE IH 420 Cotton Picker Service Repair Manual Instant Download.pdfgongyi2122252
This document provides service information for removing and installing the engine on a Case IH 420 Cotton Express cotton picker. It outlines the necessary special tools, describes how to raise the cotton basket if needed to access the engine, and provides step-by-step instructions for removing and installing the engine safely. Safety precautions are emphasized, and all removed hardware should be retained for reinstallation.
CASE IH 420 Cotton Picker Service Repair Manual Instant Download.pdfnaoji181714047
This document provides service information for removing and installing the engine on a Case IH 420 Cotton Express cotton picker. It outlines the necessary special tools, describes how to raise the cotton basket if needed to access the engine, and provides step-by-step instructions for removing and installing the engine safely. Safety precautions are emphasized, and all removed hardware should be retained for reinstallation.
CASE IH 420 Cotton Picker Service Repair Manual Instant Download.pdfsang1818141471
This document provides service information for removing and installing the engine on a Case IH 420 Cotton Express cotton picker. It outlines the necessary special tools, describes how to raise the cotton basket if needed to access the engine, and provides step-by-step instructions for removing and installing the engine safely. Safety precautions are emphasized, and all removed hardware should be retained for reinstallation.
Similar to New Holland U80C Tier 4 Tractor Backhoe Service Repair Manual (From PIN NCC570800).pdf (9)
New Holland T5.115 Electro Command Tractor Service Repair Manual.pdff8seujdjkddm
1. Refit belts on alternator and compressor. Reposition compressor and belt.
2. Apply sealing compound and reconnect engine to gearbox. Secure with bolts.
3. Reconnect wiring harnesses, sensors, pipes, filters and other components.
4. Refit starter motor, battery cables and guards. Reconnect hydraulic and cooling lines.
5. Reinstall air cleaner, exhaust, brackets and other ancillary components. Apply torque settings.
New Holland T5.115 Tractor Service Repair Manual.pdff8seujdjkddm
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. The engines are 4-cylinder, turbocharged diesel engines with direct fuel injection that produce between 99 and 114 horsepower.
New Holland T5.95 Tractor Service Repair Manual.pdff8seujdjkddm
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines across various operating parameters.
New Holland T5.105 Tractor Service Repair Manual.pdff8seujdjkddm
This service manual section provides specifications for the engines used in CNH T5.95, T5.105, and T5.115 tractors, including details about the number of cylinders, displacement, power output, cooling system, lubrication system, and other key engine components. It offers technical information on the F5DFL413C*A003, F5DFL413B*A006, and F5DFL413B*A002 engines across various operating parameters.
New Holland T5.105 Electro Command Tractor Service Repair Manual.pdff8seujdjkddm
1. Refit belts on alternator and compressor pulley and adjust tension.
2. Reposition compressor and belt, ensuring belt is seated in all pulleys.
3. Apply sealing compound and reconnect engine to gearbox.
4. Reconnect all wiring harnesses, hoses, lines, and sensors to the engine.
5. Refit components like the starter motor, battery, filters, and brackets.
6. Check all fasteners and fluid levels after installation is complete.
New Holland T5.95 Electro Command Tractor Service Repair Manual.pdff8seujdjkddm
1. Refit belts on alternator and compressor pulley and adjust tension.
2. Reposition compressor and belt, ensuring belt is seated in all pulleys.
3. Apply sealing compound and install engine/front axle assembly to gearbox, turning crankshaft for alignment.
4. Reconnect all wiring harnesses, hoses, lines, and sensors to the engine and surrounding components.
New Holland LW110B Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides instructions for removing and installing an engine and radiator on a New Holland Construction LW 110.B wheel loader. The 3-step process includes: 1) preparing the machine by lowering attachments, releasing pressures, and disconnecting batteries; 2) attaching lifting devices to the engine compartment and removing panels; and 3) removing engine and radiator components and installing the new engine.
New Holland W300C Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for CNH Italia S.p.A. wheel loaders models W270C and W300C. It contains instructions and specifications for servicing and repairing components of the wheel loaders. The manual is divided into tabs covering general information, engines, fuel system, electrical systems, steering, powertrain, brakes, hydraulics, and mounted equipment. The document provided is the table of contents, which lists each section number and title. It does not contain any repair or service instructions.
New Holland W230C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides instructions for removing the engine from a wheel loader. It involves marking components for reinstallation, draining fluids like coolant and oil, disconnecting batteries, and using lifting straps to remove the engine. Removal requires proper safety procedures and draining of hydraulic pressure before disconnecting hoses and electrical connections.
New Holland W270C Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for CNH Italia S.p.A. wheel loaders models W270C and W300C. It contains instructions and specifications for servicing and repairing components of the wheel loaders. The manual is divided into tabs covering general information, engines, fuel system, electrical systems, steering, powertrain, brakes, hydraulics, and mounted equipment. The document provides an index of sections for each component system and instructions for tasks like removing and installing engines, radiators, transmissions, hydraulic pumps and more. Safety practices and torque specifications are also included.
New Holland W300C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for a wheel loader that provides specifications and repair instructions. It contains sections on the engine, transmission, drivetrain, brakes, hydraulics, frames, steering, wheels, cab controls, electrical systems, attachments, and other components. Tables provide torque specifications for fasteners in decimal, metric, and hydraulic fitting sections.
New Holland W270C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document is a service manual for a wheel loader that provides specifications and repair instructions. It contains sections on the engine, transmission, drivetrain, brakes, hydraulics, frames, steering, wheels, cab controls, electrical systems, attachments, and bodywork. The introduction provides conversion tables between metric and imperial units as well as torque specifications for fasteners.
New Holland W190C Tier 4A (interim) Wheel Loader Service Repair Manual.pdff8seujdjkddm
This service manual provides specifications and repair information for Tier 4A interim wheel loaders. It covers the engine, transmission, four-wheel drive system, front and rear axle systems, brakes, hydraulic systems, frames, steering, wheels, cab climate control, electrical systems, front loader, bucket, cab, and decals. The manual includes an introduction on safety rules and product identification.
New Holland W190C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
- Drain engine oil and coolant from the machine. Disconnect batteries.
- Remove hood by disconnecting wiring harness, removing hinge bolts, and lifting with nylon strap through exhaust stack.
- Disconnect engine wiring harness, air intake hoses, exhaust pipes, and drive belt. Remove cooler hoses and air conditioning connections if equipped.
- The engine can now be lifted out after these removal steps are completed.
New Holland W190C Wheel Loader Service Repair Manual.pdff8seujdjkddm
This section of the service manual provides instructions for removing and installing the engine and radiator on a W190C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounting brackets and the drive belt. Engine installation is the reverse of removal. Radiator removal involves draining coolant and disconnecting hoses, while installation reconnects all components.
New Holland W170B Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides instructions for removing the engine from a wheel loader. It outlines 24 steps, including draining fluids, disconnecting hoses and wiring, and removing mounting hardware. The engine and radiator are removed together. Lifting straps are used to safely raise the hood for improved access during removal.
New Holland W170C Wheel Loader Service Repair Manual.pdff8seujdjkddm
This section provides instructions for removing and installing the engine and radiator on a W170C Wheel Loader. The engine removal process involves disconnecting battery cables, draining fluids, removing mounted components, and using an overhead hoist to lift the engine from the machine. Installation is largely the reverse process. Radiator removal involves draining coolant and removing mounting hardware, while installation reconnects hoses and mounts the radiator back in place.
New Holland W110C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides instructions for removing the engine from a W110C Wheel Loader. Key steps include: parking the machine safely, discharging pressure from hydraulic and brake systems, disconnecting batteries, draining coolant and oil, loosening hood lift cylinders, and using lifting straps to raise the hood and access the engine. A solid steel bar is then used to lift the engine out after removing attachment points. The summary provides an overview of the process for safely removing the engine.
New Holland W130C Tier 4 Wheel Loader Service Repair Manual.pdff8seujdjkddm
This section describes the removal and installation procedures for the engine and radiator on a W130C wheel loader. The key steps for engine removal include disconnecting batteries, draining fluids, removing mounting brackets and hoses. Installation is the reverse of removal. Radiator removal involves disconnecting hoses and electrical connections, and removing mounting bolts. Installation is also the reverse of removal. Torque specifications are provided for critical fasteners.
New Holland W80BTC Wheel Loader Service Repair Manual.pdff8seujdjkddm
This document provides safety instructions and technical specifications for a repair manual. It outlines general safety precautions for working on equipment, including stopping the engine and relieving hydraulic pressure before removing parts. Emergency procedures and required safety equipment are also described. Technical specifications and contact information are provided for questions.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
6. INTRODUCTION
Safety rules
DANGER
Improper operation or service of this machine can result in an accident.
Do not operate this machine or perform any lubrication, maintenance, or repair on it until you have
read and understood the operation, lubrication, maintenance, and repair information.
Failure to comply will result in death or serious injury.
D0010A
WARNING
Maintenance hazard!
Always perform all service procedures punctually at the intervals stated in this manual. This ensures
optimum performance levels and maximum safety during machine operation.
Failure to comply could result in death or serious injury.
W0132A
WARNING
Pressurized system!
Before attempting any service procedure, it is your responsibility to know the number of accumulators
on the machine, and the correct procedure for releasing the pressure of each accumulator.
Failure to comply could result in death or serious injury.
W0136A
NOTICE: Extreme working and environmental conditions require shortened service intervals.
Use Case fluids, lubricants, and filters for the best protection and performance of your machine. All fluids, lubricants,
and filters must be disposed of in compliance with environmental standards and regulations. Contact your dealer with
any questions regarding the service and maintenance of this machine.
Read the safety decals and information decals on the machine. Read the Operator’s Manual and safety manual.
Understand the operation of the machine before you start any service.
Before you service the machine, put a 'Do Not Operate' tag on the steering wheel or over the key switch. Ensure the
tag is at a location where everyone who might operate or service the machine may see clearly. One tag is included
with your new machine. Additional tags are available from your dealer.
Plastic and resin parts
• Avoid using gasoline, paint thinner, etc. when cleaning plastic parts, console, instrument cluster, etc.
• Use only water, mild soap, and a soft cloth when you clean these parts.
• Using gasoline, thinners, etc. can cause discoloration, cracking, or deformation of the part being cleaned.
47441616 27/09/2012
3
7. INTRODUCTION
Safety rules Ductile iron
DANGER
Improper operation or service of this machine can result in an accident.
Any unauthorized modifications made to this machine can have serious consequences. Consult an
authorized dealer on changes, additions, or modifications that may be required for this machine. Do
not make any unauthorized modifications.
Failure to comply will result in death or serious injury.
D0030A
Before you weld, cut, or drill holes on any part of this machine, make sure the part is not cast ductile iron. See your
dealer if you do not know if a part is cast ductile iron. The following are cast ductile iron parts:
• two wheel drive steering link
• dump links
• front axle
• Air Conditioning (A/C) compressor mounting bracket
Unauthorized modifications to cast ductile iron parts can cause injury or death. Welding, cutting, or drilling can cause
cast ductile iron to break. Do not weld, cut, or drill to repair or to attach items to cast ductile iron parts on this machine.
47441616 27/09/2012
4
8. INTRODUCTION
Safety rules
Before welding on the machine you must do the following.
If you have any questions about welding on the machine
contact your dealer.
• Disconnect the batteries.
• Disconnect the alternator terminal wires.
• Disconnect the instrument cluster.
• Disconnect the engine control unit. Disconnect all
connectors from the engine harness to the ECU.
• Disconnect the controller for the loader 4 in 1 bucket
or auxiliary hydraulics, if equipped (one connector,
located under the loader valve at the rear, left un-
derside of the machine).
47441616 27/09/2012
5
10. Engine - Engine and crankcase
Engine - General specification
Model Diesel, F5HFL413D*A
Type Four cylinder, turbocharged
Firing order 1 - 3 - 4 - 2
Bore and stroke 99mm x 110mm (3.9 in x 4.33 in)
Displacement 3.4 l (207 in³)
Compression ratio 16.5 to 1
Fuel injection Direct HPCR
Horsepower - rated at 2200 RPM
Gross
Net with 39° fan
63 kW (85 Hp)
58 kW (79 Hp)
Peak torque at 1400 RPM
Gross
Net with 39° fan
Maximum torque rise
374 N·m (276 lb ft)
364 N·m (268 lb ft)
36% ± 5 RPM
Engine - Speeds stall test check sheet
Results from stall test procedure (fill in values accordingly)
ID RPM test valve Stall test component (specified value)
1 Loader hydraulic stall speed ( 2200 - 2330 RPM)
2 Torque converter stall speed ( 2150 - 2310 RPM)
3 Combined - loader hydraulic and torque converter - stall speed ( 1610 - 1890 RPM)
Stall test reference chart
ID RPM Results
1 2230 to 2330
2 2180 to 2310
3 1610 to 1890
All systems operating within normal specified RPM values.
1 Above 2330
2 Above 2310
3 Above 1890
Engine problem. Check engine speeds. Refer to the engine service manual.
1 Below 2230
2 Below 2180
3 Below 1610
Engine problem. Check engine speeds. Replace the fuel and air filters. Refer
to the engine service manual.
1 Below 2230
2 2180 to 2310
3 Below 1610
Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump.
1 Above 2330
2 2180 to 2310
3 Above 1890
Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump. Check for leakage in the loader control valve.
1 2230 to 2330
2 2180 to 2310
3 1610 to 1890
Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump.
1 2230 to 2330
2 2180 to 2310
3 1610 to 1890
Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump.
1 2230 to 2330
2 Above 2310
3 Above 1890
Torque converter or transmission problems.
1 2230 to 2330
2 Below 2180
3 Below 1610
Torque converter or transmission problems.
47441616 27/09/2012
10.001 / 3
11. Engine - Engine and crankcase
Engine - Exploded view
1. Bolt 6. Nut
2. Washer 7. Bolt
3. Bracket, Left hand engine mount 8. Washer
4. Mount 9. Bracket, Right hand engine mount
5. Washer
47441616 27/09/2012
10.001 / 4
13. Engine - Engine and crankcase
Engine - Prepare for stall tests
Perform the stall test to find the cause of poor performance.
The main relief valve must be set within specifications to achieve accurate readings when performing the following
stall tests.
The engine is run at full throttle and the transmission and hydraulic systems are engaged separately, and then to-
gether.
Comparing the engine speeds from the stall test with the check sheets in this section will help to find the cause of the
problem. It can be necessary to check a separate system to find the exact cause of the problem.
Use a photo tachometer or other tachometer of equal accuracy to get accurate results from the stall test.
The engine, transmission and hydraulic system must be at operating temperature before doing the stall test. Heat the
oil according to instructions in this section.
Machines with standard transmission
NOTE: Check the throttle linkage adjustments.
1. Apply the parking brake.
2. Move the transmission gear selector into fourth gear.
3. Lock the brake pedals together. Put your foot on
the service brakes and hold the machine with service
brakes.
4. Release the parking brake.
5. With the engine running at low idle, move the direc-
tion control lever forward.
6. Slowly increase the engine speed to full throttle.
7. If the machine begins to move at any time, decrease
the engine speed to low idle and stop the engine.
Procedure to heat torque converter and hydraulic oil
1. Apply the parking brake.
2. Start and run the engine at low idle.
3. Run the engine at full throttle, hold the loader control
lever in the rollback position for 15 seconds.
4. Return the loader control lever to neutral for 15 sec-
onds.
5. Repeat steps 3 and 4 until the temperature of the oil
is 52 °C (126 °F). The side of the reservoir will be
very warm at this temperature.
6. With the engine running at low idle, move the trans-
mission control to fourth gear and the direction con-
trol lever to forward.
7. Run the engine at full throttle for 15 seconds.
8. Decrease the engine speed to low idle and move the
direction control lever to neutral for 15 seconds.
9. Repeat steps 6 through 8 until the pointer in the
gauge for transmission oil temperature is in the cen-
ter of the green zone of the gauge for transmission
oil temperature.
47441616 27/09/2012
10.001 / 6
14. Engine - Engine and crankcase
Stall test procedure
1. Prepare the machine for the stall test according to
instructions in this section.
2. Heat the oil according to instructions in this section.
3. Apply the parking brake and start the engine.
4. With the engine running at full throttle, hold the loader
control lever in the lift position and read the tachome-
ter. Record the reading on line 1 of the check sheet.
5. Decrease the engine speed to low idle.
6. Move the transmission control lever to fourth gear.
7. Lock the brake pedals together. Put your foot on
the service brakes and hold the machine with service
brakes.
8. Release the parking brake.
9. Move the direction control lever to forward.
10. Slowly increase the engine speed to full throttle and
read the tachometer. Record the reading on line 3
on the check sheet.
11. With the transmission control lever in fourth gear, the
direction control lever in forward, and the engine run-
ning at full throttle, hold the loader control lever in
the lift position and read the tachometer. Record the
reading on line 4 on the check sheet.
12. Decrease the engine speed to low idle, move the
directional control lever to neutral.
13. Run the engine at low idle for two minutes and then
stop the engine.
14. See the check sheet to understand the results of the
stall test.
47441616 27/09/2012
10.001 / 7
15. Engine - Engine and crankcase
Engine - Remove
Prior operation:
Drain the hydraulic tank.
Prior operation:
Disconnect the batteries.
Prior operation:
Remove the engine hood.
1. Remove the air intake tube support bracket bolts (1)
and bracket (2).
RAPH11TLB0030BA 1
2. Disconnect the A/C condenser inlet line (1).
3. Disconnect the inlet fuel cooler line (2).
4. Disconnect the outlet fuel cooler line (3).
5. Disconnect the A/C condenser outlet line (4).
RAPH11TLB0037BA 2
6. Remove the horn bracket nut (1). Place the horn and
horn bracket away from the cooling package.
RAPH11TLB0035BA 3
47441616 27/09/2012
10.001 / 8
16. Engine - Engine and crankcase
7. Loosen and remove the receiver/dryer hold-down
clamps (1). Place the receiver/dryer away from the
cooling package.
RAPH11TLB0036BA 4
8. Support the cooling package housing wrapper.
RAPH11TLB0038BA 5
9. Remove the cooling package housing wrapper bolts
(1), (2).
RAPH11TLB0029BA 6
47441616 27/09/2012
10.001 / 9
17. Engine - Engine and crankcase
10. Carefully lift and remove the cooling package hous-
ing wrapper.
RAPH11TLB0038BA 7
11. Label and disconnect the hydraulic oil hoses (1) lead-
ing to the hydraulic oil cooler.
RAPH11TLB0034BA 8
12. Disconnect the air intake tube (1) from the air cleaner.
RAPH11TLB0031BA 9
47441616 27/09/2012
10.001 / 10
18. Engine - Engine and crankcase
13. Disconnect the lower radiator hose (1) from the radi-
ator.
14. Label and disconnect the transmission oil cooler
hoses (2) leading to the transmission oil cooler.
RAPH11TLB0033BA 10
15. Disconnect the turbo outlet tube (1) at the turbo.
16. Disconnect the upper radiator hose (2) from the ra-
diator.
RAPH11TLB0032BA 11
17. Support the cooling package using safe, lifting equip-
ment.
RAPH11TLB0027BA 12
47441616 27/09/2012
10.001 / 11
19. Engine - Engine and crankcase
18. Remove the hood strut post (2) and retainer (1) .
RAPH11TLB0028BA 13
19. Remove the cooling package retaining bolts (1).
Carefully lift and remove the cooling package.
RAPH11TLB0027BA 14
20. Disconnect the A/C high pressure line (1).
21. Disconnect electrical connectors (2) and (3).
22. Disconnect the A/C low pressure line (4).
23. Disconnect the A/C condenser voltage wire (5).
RAPH11TLB0045BA 15
47441616 27/09/2012
10.001 / 12
20. Engine - Engine and crankcase
24. Disconnect fuel lines (1) and (2).
RAPH11TLB0041BA 16
25. Disconnect the water sensor electrical connector (not
shown).
NOTE: Water sensor is located at the bottom of the primary
fuel filter.
26. Remove the diesel particulate filter (DPF) system.
See Particulate filters - Remove (10.501)
27. Remove the DPF tray (1).
RAPH11TLB0022BA 17
28. Disconnect the glow plug control unit electrical con-
nector (1).
RAPH11TLB0021BA 18
47441616 27/09/2012
10.001 / 13
21. Engine - Engine and crankcase
29. Remove the supporting bracket (1) and hanging bar-
rier curtain (2).
RAPH11TLB0040BA 19
30. Disconnect the heater hose (1).
RAPH11TLB0039BA 20
31. Label and disconnect the air sensor wires (1).
RAPH11TLB0044BA 21
47441616 27/09/2012
10.001 / 14
22. Engine - Engine and crankcase
32. Label and disconnect the alternator electrical con-
nector (1) and the alternator battery wire (2).
RAPH11TLB0043BA 22
33. Remove the starter (1).
RAPH11TLB0042BA 23
34. Remove the button plug and the insert flywheel turn-
ing tool, part number 380000988.
RAPH11TLB0017BA 24
47441616 27/09/2012
10.001 / 15
23. Engine - Engine and crankcase
35. Remove the cover. Turn the flywheel using the fly-
wheel turning tool to expose the flywheel bolts (1).
Remove the flywheel bolts (1).
RAPH11TLB0016BA 25
36. Support the engine using safe, lifting equipment.
RAPH11TLB0018BA 26
37. Removing the engine mounts (1).
NOTE: Lower radiator hose removed for picture clarity.
RAPH11TLB0019BA 27
47441616 27/09/2012
10.001 / 16
24. Engine - Engine and crankcase
38. Remove the bell housing bolts (1).
RAPH11TLB0020BA 28
39. Carefully lift and remove the engine from the chassis.
RAPH11TLB0018BA 29
47441616 27/09/2012
10.001 / 17
25. Engine - Engine and crankcase
Engine - Install
1. Carefully lower the engine into the chassis.
RAPH11TLB0018BA 1
2. Install the bell housing bolts (1). Tighten the bell
housing bolts (1) to a torque of 52 - 57 N·m (38 -
42 lb ft).
RAPH11TLB0020BA 2
3. Install the engine mounts (2). Tighten the mounting
bolts (1) to 212 - 241 N·m (156 - 178 lb ft).
NOTE: Lower radiator hose removed for picture clarity.
RAPH11TLB0019BA 3
47441616 27/09/2012
10.001 / 18
26. Engine - Engine and crankcase
4. Remove the lifting equipment (1).
RAPH11TLB0018BA 4
5. Install the flywheel bolts (1). Tighten the flywheel
bolts to 30 N·m (22 lb ft)
RAPH11TLB0016BA 5
6. Install the bell housing flywheel bolt cover and button
plug.
7. Install the starter (1). Tighten starter bolts (2) to a
torque of 45 N·m (33 lb ft).
RAPH11TLB0042BA 6
47441616 27/09/2012
10.001 / 19
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Engine - Engine and crankcase
8. Connect the alternator electrical connector (1) and
the alternator battery wire (2).
RAPH11TLB0043BA 7
9. Connect the air sensor wires (1).
RAPH11TLB0044BA 8
10. Connect the heater hose (1).
RAPH11TLB0039BA 9
47441616 27/09/2012
10.001 / 20
29. Engine - Engine and crankcase
11. Install the hanging barrier curtain (2) and the support-
ing bracket (1).
RAPH11TLB0040BA 10
12. Connect the glow plug control unit electrical connec-
tor (1).
RAPH11TLB0021BA 11
13. Install the diesel particulate filter (DPF) tray (1).
RAPH11TLB0022BA 12
14. Install the DPF system. See Particulate filters -
Install (10.501).
47441616 27/09/2012
10.001 / 21
30. Engine - Engine and crankcase
15. Connect the water sensor electrical connector (not
shown).
NOTE: Water sensor is located at the bottom of the primary
fuel filter.
16. Connect fuel lines (1) and (2).
RAPH11TLB0041BA 13
17. Connect the A/C high pressure line (1).
18. Connect electrical connectors (2) and (3).
19. Connect the A/C low pressure line (4).
20. Connect the A/C condenser voltage wire (5).
RAPH11TLB0045BA 14
21. Carefully lower the cooling package onto the chas-
sis. Install the cooling package retaining bolts (2).
Remove the lifting equipment (1).
NOTICE: Cooling package fan shroud may come in contact
with engine fan blade. Verify engine fan blade has proper
clearance for rotation. Adjust cooling package as neces-
sary.
RAPH11TLB0027BA 15
47441616 27/09/2012
10.001 / 22
31. Engine - Engine and crankcase
22. Install the hood strut post (2) and retainer (1).
RAPH11TLB0028BA 16
23. Connect the turbo outlet tube (1) to the turbo.
24. Connect the upper radiator hose (2) to the radiator.
RAPH11TLB0032BA 17
25. Connect the lower radiator hose (1) to the radiator.
26. Connect the transmission oil cooler hoses (2) to the
transmission oil cooler.
RAPH11TLB0033BA 18
47441616 27/09/2012
10.001 / 23
32. Engine - Engine and crankcase
27. Connect the air intake tube (1) to the air cleaner.
RAPH11TLB0031BA 19
28. Connect the hydraulic oil hoses (1) to the hydraulic
oil cooler.
RAPH11TLB0034BA 20
29. Lower the cooling package housing wrapper onto the
cooling package.
RAPH11TLB0038BA 21
47441616 27/09/2012
10.001 / 24
33. Engine - Engine and crankcase
30. Install the cooling package housing wrapper bolts
(1), (2).
RAPH11TLB0029BA 22
31. Remove the lifting equipment (1).
RAPH11TLB0038BA 23
32. Install the receiver/dryer (1).
RAPH11TLB0036BA 24
47441616 27/09/2012
10.001 / 25