The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 8 bar by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
New Holland TC5080 Hillside Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New Holland TC5060 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for various tractor models. It includes:
- An introduction section outlining the manual's contents and how to navigate it.
- Individual sections covering different vehicle systems like the engine, transmission, brakes, hydraulics and electrical systems.
- Chapters within each section detailing the technical, functional, diagnostic and service data for components of that system.
- Illustrations, diagrams and step-by-step instructions for removing and installing parts.
The manual is intended as a technical reference for carrying out maintenance and repairs according to the manufacturer's specifications.
New Holland TC5050 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the TC5000 combine includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are two or three hydraulic pumps, an oil tank, filter, accumulator, lift cylinders, steering valve and cylinders, and controls for the header and other attachments.
New Holland TC5080 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New Holland TC5040 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the TC5000 combine includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are two or three hydraulic pumps, an oil tank, filter, accumulator, lift cylinders, steering valve and cylinders, and controls for the header and other attachments.
New Holland TC5060 Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 8 bar by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
New Holland TC5050 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, cleaning, and the cab.
The sections contain technical data, descriptions of component function, diagnostic data including fault codes, and procedures for removal and installation of components.
New Holland TC5040 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for components like the engine air compressor, clutch hydraulic control, gearbox, hydrostatic drive, brakes, hydraulic pumps and valves, electrical modules, reel, feed rollers, threshing drum, straw walkers, cleaning systems and more.
New Holland TC5080 Hillside Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New Holland TC5060 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for various tractor models. It includes:
- An introduction section outlining the manual's contents and how to navigate it.
- Individual sections covering different vehicle systems like the engine, transmission, brakes, hydraulics and electrical systems.
- Chapters within each section detailing the technical, functional, diagnostic and service data for components of that system.
- Illustrations, diagrams and step-by-step instructions for removing and installing parts.
The manual is intended as a technical reference for carrying out maintenance and repairs according to the manufacturer's specifications.
New Holland TC5050 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the TC5000 combine includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are two or three hydraulic pumps, an oil tank, filter, accumulator, lift cylinders, steering valve and cylinders, and controls for the header and other attachments.
New Holland TC5080 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New Holland TC5040 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the TC5000 combine includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are two or three hydraulic pumps, an oil tank, filter, accumulator, lift cylinders, steering valve and cylinders, and controls for the header and other attachments.
New Holland TC5060 Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 8 bar by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
New Holland TC5050 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, cleaning, and the cab.
The sections contain technical data, descriptions of component function, diagnostic data including fault codes, and procedures for removal and installation of components.
New Holland TC5040 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for components like the engine air compressor, clutch hydraulic control, gearbox, hydrostatic drive, brakes, hydraulic pumps and valves, electrical modules, reel, feed rollers, threshing drum, straw walkers, cleaning systems and more.
New Holland L228 TIER 4B (FINAL) North America Skid Steer Loader Service Repa...fusekdmdmded
The document provides service information for New Holland skid steer loaders and compact track loaders, including:
- A parts manual for engines, power couplings, axles, hydraulics, frames, wheels, tracks, electrical systems, and other components
- Procedures for draining fluids, removing the engine, radiator, and other components for service or replacement
- Specifications for tightening torques and replacement of parts
New Holland TC5070 Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 8 bar by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
New Holland L228 TIER 4B (FINAL) Europe Skid Steer Loader Service Repair Manu...fusekdmdmded
The document provides service information for New Holland skid steer loaders and compact track loaders with Tier 4B diesel engines, including removal procedures for major engine components. It describes disconnecting hoses and electrical connections, removing covers, shrouds, and mounting hardware, and using lifting equipment to remove items like the engine, radiator, and muffler. The goal is to safely prepare the engine for maintenance or replacement while following safety precautions.
New Holland CX5090 Laterale Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections
- Details on the primary hydraulic power system, including pump specifications and a hydraulic schematic diagram
- Images showing the location of hydraulic components on the front of the machine
The manual provides technical data, diagrams, and images to support servicing the machine's distribution systems. It gives specifications for hydraulic components and diagrams the hydraulic circuit, locating key components.
New Holland CX5090 Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
This document is a service manual for CX5000 and CX6000 series machines. It contains sections covering the machine's hydraulic, pneumatic, electrical and electronic systems, engines, transmissions, axles, brakes, steering, frames, cabs, user platforms, environmental controls, lifting and leveling systems, and crop processing functions. Each section contains technical data, descriptions of functionality, diagnostic information, and service procedures for the machine's components and systems.
New Holland TC5060 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the TC5000 combine includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are two or three hydraulic pumps, an oil tank, filter, accumulator, lift cylinders, steering valve and cylinders, and controls for the header, reel, and unloading auger. Lateral flotation components are included for optional equipment.
New Holland L221 TIER 4B Final [NEM479941- ]North America Skid Steer Loader S...fusekdmdmded
The document provides service information for New Holland skid steer loaders and compact track loaders with Tier 4B diesel engines, including removal procedures for major engine components. It describes disconnecting hoses and electrical connections, removing covers, shrouds, and mounting hardware, and using lifting equipment to remove items like the engine, radiator, and muffler. The goal is to safely prepare the engine for maintenance or replacement while following safety precautions.
New Holland L223 TIER 4 Skid Steer Loader Service Repair Manual [NDM474381 - ...fusekdmdmded
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical connections and hoses, removing covers and cooling components, and then removing mounting hardware and the engine hood. Specific models and replacement part numbers are listed. Safety warnings are provided throughout regarding personal safety and relieving pressure before disconnecting lines.
New Holland CX5090 Tier 3 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details on the primary hydraulic system, including pump specifications and a hydraulic schematic diagram labeling key components.
- Images showing the location of hydraulic components such as the header quick-release coupler, lateral float cylinder, header lift cylinders, and straw elevator.
New Holland L225 TIER 4 Skid Steer Loader Service Repair Manual [NDM461085 - ...fusekdmdmded
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical connections and hoses, removing covers and cooling components, and then removing mounting hardware and the engine hood. Specific models and replacement part numbers are listed. Safety warnings are provided throughout regarding personal safety and relieving pressure before disconnecting lines.
New Holland W70C HS Tier 4B (final) Compact Wheel Loader Service Repair Manua...fusekdmdmded
1. Disconnect wiring harnesses, condenser hoses (if equipped), and remove engine hood to access the engine.
2. Remove right and left engine grids by removing mounting bolts.
3. Drain hydraulic system and bleed accumulators before performing any service work.
New Holland W60C ZB Tier 4B (final) Compact Wheel Loader Service Repair Manua...fusekdmdmded
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and grille.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser.
3. Put battery main switch in OFF position. Remove engine by disconnecting mounting bolts after preparing hydraulic system.
New Holland CX5090 Hillside Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details on the primary hydraulic system, including specifications for the main, steering, and lateral flotation pumps.
- Schematics and diagrams showing the layout of the hydraulic system and location of key components.
New Holland CX740 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides details on the primary hydraulic power system for New Holland CX combine harvesters. It includes a closed-center load sensing variable displacement pump that supplies oil to circuits for steering, header height control, straw elevator functions, lateral flotation control, reel adjustment, and unloading tube control. Key components are labeled in diagrams and their functions are described.
New Holland TC5070 Hillside Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New Holland CX760 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides details on the primary hydraulic power system for a New Holland combine. It includes a closed-center load sensing variable displacement pump that supplies oil to circuits for steering, header height control, straw elevator functions, lateral flotation control, reel adjustment, and unloading tube control. Key components described are the hydraulic pump, priority valve, filters, control valves, motors, cylinders, and accumulators that make up the high-pressure circuit.
New Holland CX5080 Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details on the primary hydraulic system, including specifications for the main, steering, and lateral flotation pumps.
- Schematics and diagrams showing the layout of the hydraulic system and location of key components.
New Holland CX820 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides details on the primary hydraulic power system for a New Holland combine. It includes a closed-center load sensing variable displacement pump that supplies oil to circuits for steering, header height control, straw elevator functions, lateral flotation control, reel adjustment, and unloading tube control. Key components described are the hydraulic pump, priority valve, filters, control valves, motors, cylinders, and accumulators that make up the high-pressure circuit.
New Holland TC5080 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
This service manual provides information on servicing TC5040, TC5050, TC5060, TC5070, TC5080, and TC5080 Hillside combines. The manual is divided into sections covering the combines' distribution systems, power train, travelling systems, body and structure, tool positioning, and crop processing systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical, hydraulic, and electronic components.
New Holland TC5070 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the combines includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are the hydraulic pumps, oil tank, filters, valves, cylinders, and accumulators. Hydraulic flow is distributed to functions like the header, steering, and optional lateral flotation systems.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
New Holland L228 TIER 4B (FINAL) North America Skid Steer Loader Service Repa...fusekdmdmded
The document provides service information for New Holland skid steer loaders and compact track loaders, including:
- A parts manual for engines, power couplings, axles, hydraulics, frames, wheels, tracks, electrical systems, and other components
- Procedures for draining fluids, removing the engine, radiator, and other components for service or replacement
- Specifications for tightening torques and replacement of parts
New Holland TC5070 Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The air compressor supplies compressed air to the reservoir tank to provide a source of compressed air for cleaning and tire inflation. It is a single cylinder, gear-driven compressor mounted directly to the engine. Engine oil lubricates the compressor. The compressed air relief valve protects the system from pressures over 8 bar by venting excess pressure. It can be removed by draining the air and coolant lines, loosening connections, and removing mounting bolts and nuts.
New Holland L228 TIER 4B (FINAL) Europe Skid Steer Loader Service Repair Manu...fusekdmdmded
The document provides service information for New Holland skid steer loaders and compact track loaders with Tier 4B diesel engines, including removal procedures for major engine components. It describes disconnecting hoses and electrical connections, removing covers, shrouds, and mounting hardware, and using lifting equipment to remove items like the engine, radiator, and muffler. The goal is to safely prepare the engine for maintenance or replacement while following safety precautions.
New Holland CX5090 Laterale Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections
- Details on the primary hydraulic power system, including pump specifications and a hydraulic schematic diagram
- Images showing the location of hydraulic components on the front of the machine
The manual provides technical data, diagrams, and images to support servicing the machine's distribution systems. It gives specifications for hydraulic components and diagrams the hydraulic circuit, locating key components.
New Holland CX5090 Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
This document is a service manual for CX5000 and CX6000 series machines. It contains sections covering the machine's hydraulic, pneumatic, electrical and electronic systems, engines, transmissions, axles, brakes, steering, frames, cabs, user platforms, environmental controls, lifting and leveling systems, and crop processing functions. Each section contains technical data, descriptions of functionality, diagnostic information, and service procedures for the machine's components and systems.
New Holland TC5060 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the TC5000 combine includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are two or three hydraulic pumps, an oil tank, filter, accumulator, lift cylinders, steering valve and cylinders, and controls for the header, reel, and unloading auger. Lateral flotation components are included for optional equipment.
New Holland L221 TIER 4B Final [NEM479941- ]North America Skid Steer Loader S...fusekdmdmded
The document provides service information for New Holland skid steer loaders and compact track loaders with Tier 4B diesel engines, including removal procedures for major engine components. It describes disconnecting hoses and electrical connections, removing covers, shrouds, and mounting hardware, and using lifting equipment to remove items like the engine, radiator, and muffler. The goal is to safely prepare the engine for maintenance or replacement while following safety precautions.
New Holland L223 TIER 4 Skid Steer Loader Service Repair Manual [NDM474381 - ...fusekdmdmded
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical connections and hoses, removing covers and cooling components, and then removing mounting hardware and the engine hood. Specific models and replacement part numbers are listed. Safety warnings are provided throughout regarding personal safety and relieving pressure before disconnecting lines.
New Holland CX5090 Tier 3 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details on the primary hydraulic system, including pump specifications and a hydraulic schematic diagram labeling key components.
- Images showing the location of hydraulic components such as the header quick-release coupler, lateral float cylinder, header lift cylinders, and straw elevator.
New Holland L225 TIER 4 Skid Steer Loader Service Repair Manual [NDM461085 - ...fusekdmdmded
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical connections and hoses, removing covers and cooling components, and then removing mounting hardware and the engine hood. Specific models and replacement part numbers are listed. Safety warnings are provided throughout regarding personal safety and relieving pressure before disconnecting lines.
New Holland W70C HS Tier 4B (final) Compact Wheel Loader Service Repair Manua...fusekdmdmded
1. Disconnect wiring harnesses, condenser hoses (if equipped), and remove engine hood to access the engine.
2. Remove right and left engine grids by removing mounting bolts.
3. Drain hydraulic system and bleed accumulators before performing any service work.
New Holland W60C ZB Tier 4B (final) Compact Wheel Loader Service Repair Manua...fusekdmdmded
1. Disconnect wiring harnesses, condenser hoses (if equipped), and rear lights. Remove engine hood and grille.
2. Drain air conditioning system (if equipped) and disconnect fan connector. Remove condenser.
3. Put battery main switch in OFF position. Remove engine by disconnecting mounting bolts after preparing hydraulic system.
New Holland CX5090 Hillside Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details on the primary hydraulic system, including specifications for the main, steering, and lateral flotation pumps.
- Schematics and diagrams showing the layout of the hydraulic system and location of key components.
New Holland CX740 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides details on the primary hydraulic power system for New Holland CX combine harvesters. It includes a closed-center load sensing variable displacement pump that supplies oil to circuits for steering, header height control, straw elevator functions, lateral flotation control, reel adjustment, and unloading tube control. Key components are labeled in diagrams and their functions are described.
New Holland TC5070 Hillside Combine Harvesters Service Repair Manual 1.pdffusekdmdmded
The document provides service information for engines and various components of agricultural combines.
It includes sections on the engine, clutch, transmission, front and rear axle systems, brakes and controls, hydraulic systems, electrical systems, attachments and headers, product feeding, threshing, separation, residue handling, cleaning, and the cab.
Technical data, functional descriptions, diagnostic information, and service procedures are provided for mechanical, electrical and hydraulic components. Fault codes and troubleshooting information is also included for electrical systems.
New Holland CX760 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides details on the primary hydraulic power system for a New Holland combine. It includes a closed-center load sensing variable displacement pump that supplies oil to circuits for steering, header height control, straw elevator functions, lateral flotation control, reel adjustment, and unloading tube control. Key components described are the hydraulic pump, priority valve, filters, control valves, motors, cylinders, and accumulators that make up the high-pressure circuit.
New Holland CX5080 Tier 4 Combine Harvester Service Repair Manual.pdffusekdmdmded
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections.
- Details on the primary hydraulic system, including specifications for the main, steering, and lateral flotation pumps.
- Schematics and diagrams showing the layout of the hydraulic system and location of key components.
New Holland CX820 Combine Harvesters Service Repair Manual.pdffusekdmdmded
The document provides details on the primary hydraulic power system for a New Holland combine. It includes a closed-center load sensing variable displacement pump that supplies oil to circuits for steering, header height control, straw elevator functions, lateral flotation control, reel adjustment, and unloading tube control. Key components described are the hydraulic pump, priority valve, filters, control valves, motors, cylinders, and accumulators that make up the high-pressure circuit.
New Holland TC5080 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
This service manual provides information on servicing TC5040, TC5050, TC5060, TC5070, TC5080, and TC5080 Hillside combines. The manual is divided into sections covering the combines' distribution systems, power train, travelling systems, body and structure, tool positioning, and crop processing systems. Each section contains technical data, functional descriptions, diagnostics, and service procedures for the machines' mechanical, electrical, hydraulic, and electronic components.
New Holland TC5070 Hillside Combine Harvesters Service Repair Manual.pdffusekdmdmded
The primary hydraulic power system for the combines includes multiple pumps that supply hydraulic fluid to various systems through a valve stack. The main components are the hydraulic pumps, oil tank, filters, valves, cylinders, and accumulators. Hydraulic flow is distributed to functions like the header, steering, and optional lateral flotation systems.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
7. INTRODUCTION
Foreword
IMPORTANT INFORMATION
All repair and maintenance works listed in this manual must be carried out only by staff belonging to the NEW HOL-
LAND Service network, strictly complying with the instructions given and using, whenever required, the special tools.
Anyone who carries out the above operations without complying with the prescriptions shall be responsible for the
subsequent damages.
The manufacturer and all the organizations of its distribution chain, including - without limitation - national, regional or
local dealers, reject any responsibility for damages due to the anomalous behavior of parts and/or components not
approved by the manufacturer himself, including those used for the servicing or repair of the product manufactured
or marketed by the Manufacturer. In any case, no warranty is given or attributed on the product manufactured or
marketed by the Manufacturer in case of damages due to an anomalous behavior of parts and/or components not
approved by the Manufacturer.
No reproduction, though partial of text and illustrations allowed
47663637 18/02/2014
3
8. INTRODUCTION
Basic instructions - How to use and navigate through this manual
Technical Information
This manual has been produced by a new technical information system. This new system is designed to deliver
technical information electronically through Web delivery (eTim), DVD and in paper manuals. A coding system called
SAP has been developed to link the technical information to other Product Support functions, e.g., Warranty.
Technical information is written to support the maintenance and service of the functions or systems on a customer's
machine. When a customer has a concern on his machine it is usually because a function or system on his machine
is not working at all, is not working efficiently, or is not responding correctly to his commands. When you refer to
the technical information in this manual to resolve that customer's concern, you will find all the information classified
using the SAP coding, according to the functions or systems on that machine. Once you have located the technical
information for that function or system then you will find all the mechanical, electrical or hydraulic devices, compo-
nents, assemblies and sub assemblies for that function or system. You will also find all the types of information that
have been written for that function or system, the technical data (specifications), the functional data (how it works),
the diagnostic data (fault codes and troubleshooting) and the service data (remove, install adjust, etc.).
By integrating SAP coding into technical information, you will be able to search and retrieve just the right piece of
technical information you need to resolve that customer's concern on his machine. This is made possible by attaching
3 categories to each piece of technical information during the authoring process.
The first category is the Location, the second category is the Information Type and the third category is the Product:
• LOCATION - is the component or function on the machine, that the piece of technical information is going to describe
e.g. Fuel tank.
• INFORMATION TYPE - is the piece of technical information that has been written for a particular component or
function on the machine e.g. Capacity would be a type of Technical Data that would describe the amount of fuel
held by the Fuel tank.
• PRODUCT - is the model for which the piece of technical information is written.
Every piece of technical information will have those 3 categories attached to it. You will be able to use any combination
of those categories to find the right piece of technical information you need to resolve that customer's concern on his
machine.
That information could be:
• the description of how to remove the cylinder head
• a table of specifications for a hydraulic pump
• a fault code
• a troubleshooting table
• a special tool
47663637 18/02/2014
4
9. INTRODUCTION
How to use this manual
This manual is divided into Sections. Each Section is then divided into Chapters. Contents pages are included at the
beginning of the manual, then inside every Section and inside every Chapter. An alphabetical Index is included at the
end of a Chapter. Page number references are included for every piece of technical information listed in the Chapter
Contents or Chapter Index.
Each Chapter is divided into four Information types:
• Technical Data (specifications) for all the mechanical, electrical or hydraulic devices, components and, assemblies.
• Functional Data (how it works) for all the mechanical, electrical or hydraulic devices, components and assemblies.
• Diagnostic Data (fault codes, electrical and hydraulic troubleshooting) for all the mechanical, electrical or hydraulic
devices, components and assemblies.
• Service Data (remove disassembly, assemble, install) for all the mechanical, electrical or hydraulic devices, com-
ponents and assemblies.
Sections
Sections are grouped according to the main functions or a systems on the machine. Each Section is identified by a
number 00, 35, 55, etc. The amount of Sections included in the manual will depend on the type and function of the
machine that the manual is written for. Each Section has a Contents page listed in alphabetic/numeric order. This
table illustrates which Sections could be included in a manual for a particular product.
PRODUCT
Tractors
Vehicles with working arms: backhoes, excavators,
skid steers, ….
Combines, forage harvesters, balers, ….
Seeding, planting, floating, spraying
equipment, ….
SECTION Mounted equipment and tools, ….
00 - Maintenance
05 - Machine completion and equipment
10 - Engine
14 - Main gearbox and drive
18 - Clutch
21 - Transmission
23 - Four wheel drive system
25 - Front axle system
27 - Rear axle system
29 - Hydrostatic drive
31 - Implement power take-off
33 - Brakes and controls
35 - Hydraulic systems
36 - Pneumatic system
37 - Hitches, drawbars and implement couplings
39 - Frames and ballasting
41 - Steering
44 - Wheels
46 - Steering clutches
48 - Tracks and track suspension
50 - Cab climate control
55 - Electrical systems
56 - Grape harvester shaking
58 - Attachments/headers
60 - Product feeding
61 - Metering system
62 - Pressing - Bale formation
47663637 18/02/2014
5
10. INTRODUCTION
63 - Chemical applicators
64 - Chopping
66 - Threshing
68 - Tying/Wrapping/Twisting
69 - Bale wagons
70 - Ejection
71 - Lubrication system
72 - Separation
73 - Residue handling
74 - Cleaning
75 - Soil preparation/Finishing
76 - Secondary cleaning / Destemmer
77 - Seeding
78 - Spraying
79 - Planting
80 - Crop storage / Unloading
82 - Front loader and bucket
83 - Telescopic single arm
84 - Booms, dippers and buckets
86 - Dozer blade and arm
88 - Accessories
89 - Tools
90 - Platform, cab, bodywork and decals
47663637 18/02/2014
6
12. Engine - Engine air compressor
Air compressor - Static description
TC5070 WE
TC5080 WE
The air compressor (3) is a single cylinder, gear driven air compressor, which supplies air to a reservoir tank, enabling
the operator to have a source of compressed air for cleaning purposes and tyre inflation. The compressor is mounted
directly on the engine with the two nuts (10).
Engine oil is supplied through an internal connection with the engine, using engine oil pressure to lubricate the com-
pressor.
The compressed air is delivered through tubing to a combination pressure relief control valve, and from there to the
reservoir tank located on the straw hood of the combine. A quick disconnect fitting allows easy connection to the air
supply for blow off nozzles as well as for tyre inflation equipment.
ZEIL06CS0085A0B 1
47663637 18/02/2014
10.1 [10.450] / 3
13. Engine - Engine air compressor
Air compressor - Drawing
TC5070 WE
TC5080 WE
ZEIL11CX0668G0B 1
Reference Port Port Name Port Function
1 0 Inlet Port Supplies Compressor with clean intake air
2 2 Discharge Port Expels pressurized air for system
4 8.1 Oil Supply Supplies compressor with lube oil from engine
5 8.2 Oil Drain Allows lube oil to return to engine
6 9.1 Coolant Receive coolant from engine
7 9.2 Coolant Return coolant to engine
47663637 18/02/2014
10.1 [10.450] / 4
14. Engine - Engine air compressor
Compressed air tank Relief valve - Drawing
TC5070 WE
TC5080 WE
ZEIL11CX0667G0B 1
Reference Port Port name Port function
1 1 Inlet Pressurized air "in" from compressor
2 21 Outlet Pressurized air "out" to reservoir tank and blow
off line quick connect port
3 22 Auxiliary supply Auxiliary port not used in this application
4 1-2 Tire inflation device Port used to connect tire inflation device
5 3 Exhaust for compressor idling Discharge exhaust for excess pressure in system
47663637 18/02/2014
10.1 [10.450] / 5
15. Engine - Engine air compressor
Compressed air tank Relief valve - Static description
TC5070 WE
TC5080 WE
The pressure relief valve is developed to protect the system against pressures higher than 8 bar ( 116 psi).
Port (1) is connected to the air compressor, port (21) is connected to the pressurized reservoir.
When the pressure on port (21) reaches 8 bar ( 116 psi), the control valve (9d) will be activated which means that
also control valve (9c) will be activated. The pressure from the compressor will now pass through port (3).
If the pressure drops below 8 bar ( 116 psi) by activation a engaging valve, control valve (9d) will close.
Valve (9c) will not close immediately but will remain in the open position until the pressure exerted on the control of
valve (9c) will be reduced by 0.6 bar ( 8.7 psi). Then the air will pass through valve (9b).
Schematic diagram
ZDA7672Z 1
47663637 18/02/2014
10.1 [10.450] / 6
16. Engine - Engine air compressor
Air compressor - Remove
TC5070 WE
TC5080 WE
1. Bleed the air from the system by opening the drain (2)
at the bottom of the air reservoir.
ZEIL06TC00034A0 1
2. Loosen the retaining strap (1) and remove the air inlet
pipe (2) from the air compressor (3).
NOTE: Protect the air inlet and outlet ports from dirt
ingress.
3. Loosen the connection (4) to remove the hose (5) from
the air compressor (3).
ZEIL06CS0082A0B 2
4. Drain sufficient coolant from the engine cooling system
to allow removal of the coolant lines.
NOTE: Refer to the Operator’s Manual of your machine.
5. Loosen the connection (6).
ZEIL06CS0083A0B 3
6. Loosen the connection (7).
7. Remove the four bolts (8) to remove the support (9).
ZEIL06CS0084A0B 4
47663637 18/02/2014
10.1 [10.450] / 7
17. Engine - Engine air compressor
8. Remove the two nuts (10) to remove the air compressor
(3) from the engine.
ZEIL06CS0085A0B 5
47663637 18/02/2014
10.1 [10.450] / 8
18. Engine - Engine air compressor
Air compressor - Install
TC5070 WE
TC5080 WE
1. Install the air compressor (3) on the engine and tighten
the two nuts (10).
ZEIL06CS0085A0B 1
NOTE: Make sure that the O-ring (11) is positioned well. If
necessary apply grease.
ZEIL06CS0086A0B 2
2. Install the support (9) with the four bolts (8).
3. Install the tube and tighten the connection (7).
ZEIL06CS0084A0B 3
4. Install the tube and tighten the connection (6).
ZEIL06CS0083A0B 4
47663637 18/02/2014
10.1 [10.450] / 9
19. Engine - Engine air compressor
5. Install the hose (5) on the air compressor (3) and
tighten the connection (4).
6. Install the pipe (2) on the air compressor (3) and tighten
the retaining strap (1).
ZEIL06CS0082A0B 5
7. Close the drain (2) at the bottom of the reservoir.
8. Add engine coolant to the cooling system, refer to the
Operator’s Manual for more details.
9. Start the engine to charge the system with air. Allow the
air system to build up pressure to the governor cutout.
Stop the engine and use a soap and water solution at
the connection points to check for air leaks. Make any
necessary repairs.
ZEIL06TC00034A0 6
47663637 18/02/2014
10.1 [10.450] / 10
20. Transmission - Mechanical transmission
Mechanical transmission - Remove
TC5070 WE
TC5080 WE
NOTICE: Before removing any components, secure the machine safely in place by placing adequate wedges against
both traction and steering wheels.
1. On the left-hand side, remove the required covers by
loosening the bolts.
RNIL08TC0029A0A 1
2. Loosen the hose clamps (1) and (2).
RNIL08TC0030A0B 2
3. Support the hydrostatic motor (1) and loosen the four
nuts (2). (only two nuts are shown)
Pull the hydrostatic motor (1) out of the gearbox.
NOTE: In some cases it will be necessary to remove the
LHS traction wheel for taking the hydrostatic motor out of
the gearbox.
ZDA7815A 3
47663637 18/02/2014
21.1 [21.114] / 8
21. Transmission - Mechanical transmission
4. Disconnect the hand brake cable (1) by removing the
bolt.
RNIL08TC0031A0B 4
5. Disconnect the combine speed sensor (1).
RNIL08TC0032A0B 5
6. Disconnect the gearshift bar (4).
ZDA7817A 6
7. Disconnect the sleeves (1) and the brake lines on both
sides of the traction gearbox.
CAUTION
The gearbox is heavy (380 kg [838 lbs]). Take extreme
caution when removing the gearbox! Use a supporting
device which can handle this weight!
Z022
RNIL08TC0033A0B 7
47663637 18/02/2014
21.1 [21.114] / 9
22. Transmission - Mechanical transmission
8. Loosen the three bolts (1) at both sides of traction gear-
box.
Lower the traction gearbox and remove it from under-
neath the combine.
ZDA7818A 8
47663637 18/02/2014
21.1 [21.114] / 10
23. Transmission - Mechanical transmission
Mechanical transmission - Install
TC5070 WE
TC5080 WE
1. Bring the traction gearbox onto his place.
On both sides of the traction gearbox, install the three
bolts (1).
NOTE: Apply Loctite 242 (OMNIFIT 50M, PERMABOND
113) onto the bolts (1).
ZDA7818A 1
2. Connect the sleeves (1) and the brake lines on both
sides of the traction gearbox.
RNIL08TC0033A0B 2
3. Connect the gearshift bar (4).
Adjust, if necessary, refer to Shifting disk system -
Adjust Bar (21.145).
ZDA7817A 3
47663637 18/02/2014
21.1 [21.114] / 11
24. Transmission - Mechanical transmission
4. Connect the ground speed sensor (1).
RNIL08TC0032A0B 4
5. Connect the hand brake cable (1).
Adjust, if necessary, refer to Brake pedals - Adjust
(33.202).
RNIL08TC0031A0B 5
6. Support the weight of the hydrostatic motor (1).
Raise the motor into position on the traction gearbox.
Apply grease onto the spline shaft of the motor (1).
Engage the spline shaft of the motor and push it into
the female spline until the mounting flange is against
the transmission.
Install the four nuts (2).
NOTE: Before install the four nuts, apply Loctite 270 (OM-
NIFIT 200M, PERMABOND 118).
ZDA7815A 6
7. Install the hose clamps (1) and (2).
RNIL08TC0030A0B 7
47663637 18/02/2014
21.1 [21.114] / 12
25. Transmission - Mechanical transmission
8. Install the removed covers and tighten the bolts.
RNIL08TC0029A0A 8
Next operation:
Hydraulic service brakes - Bleed (33.202).
47663637 18/02/2014
21.1 [21.114] / 13
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Transmission - Mechanical transmission external controls
Transmission housing cover - Disassemble
TC5060 WE
NOTE: Refer to Shifting disk system - Exploded view (21.145)
1. Loosen the drain plug and drain the oil from the gear-
box. Refer to the Operator's Manual: "SECTION 4
- LUBRICATION AND MAINTENANCE" paragraph
headed: "Traction gearbox".
2. Loosen the plug (112) with the seal ring (113) and the
breather (114).
ZEIL08TC0466A0B 1
3. Loosen the bolts (2) and remove the cover (1) of the
gearbox.
ZEIL08TC0303A0B 2
4. Loosen the bolt (3) from the gear shift finger (6).
ZEIL08TC0463A0B 3
47663637 18/02/2014
21.2 [21.130] / 10
28. Transmission - Mechanical transmission external controls
5. Remove the gear shift shaft (4) from the cover (1).
NOTICE: When removing the plate (5), mark it because it
is not symmetrical.
6. Remove the plate (5) and the gear shift finger (6) from
the cover (1).
ZEIL08TC0305A0B 4
7. Remove the shaft seals (7) from the cover (1) using a
screw driver.
ZEIL08TC0306A0B 5
47663637 18/02/2014
21.2 [21.130] / 11
29. Transmission - Mechanical transmission external controls
Transmission housing cover - Assemble
TC5060 WE
NOTE: Refer to Shifting disk system - Exploded view (21.145)
1. Install both shaft seals (7) in the cover (1).
ZEIL08TC0462A0B 1
NOTICE: The plate (5) must be assembled in such a way that the teeth are in a centralized position in relation to the
cover.
2. Position the gear shift finger (6) and the plate (5).
3. Install the gear shift shaft (4), fix as shown the gear shift
finger (6) with the bolt (3) using LOCTITE® 243. Tighten
with a torque of 46 Nm (33.9 lb ft).
ZEIL08TC0463A0B 2
4. Install the cover (1) applying LOCTITE® 574 on the con-
tact surface and fix it with the bolts (2), tighten with a
torque of 23 Nm (17.0 lb ft).
ZEIL08TC0465A0B 3
47663637 18/02/2014
21.2 [21.130] / 12
30. Transmission - Mechanical transmission external controls
5. Install the plug (112) with the seal ring (113) in the cover
(1). Tighten the plug (112) with a torque of 200 N·m
(147.5 lb ft).
6. Install the breather (114) on the plug (112) and tighten
with a torque of 12.1 N·m (8.9 lb ft).
ZEIL08TC0466A0B 4
7. Install the drain plug (115) and the level plug (121) and
tighten with a torque of 50 Nm (36.9 lb ft).
Fill the gearbox (9) with oil. Refer to the Operator's
Manual: "SECTION 4 - LUBRICATION AND MAINTE-
NANCE" paragraph headed: "Traction gearbox".
ZEIL08TC0467A0B 5
47663637 18/02/2014
21.2 [21.130] / 13