Seconda circolare del Convegno SIA BOLOGNA 2015Mimmo Ventrella
ll XLIV Convegno Nazionale della Società Italiana di Agronomia (SIA) - L'Agronomia per la gestione dei sistemi produttivi agrari - si svolgerà dal 14 al 16 Settembre 2015 presso l’Aula Magna del Dipartimento di Scienze Agrarie dell’Università di Bologna in Viale Giuseppe Fanin 44, Bologna.
Seconda circolare del Convegno SIA BOLOGNA 2015Mimmo Ventrella
ll XLIV Convegno Nazionale della Società Italiana di Agronomia (SIA) - L'Agronomia per la gestione dei sistemi produttivi agrari - si svolgerà dal 14 al 16 Settembre 2015 presso l’Aula Magna del Dipartimento di Scienze Agrarie dell’Università di Bologna in Viale Giuseppe Fanin 44, Bologna.
A closer look at samsung galaxy j7 primeHouse of IT
Here's an infographic of the cool features you can expect from Samsung's Galaxy J7.
https://houseofit.ph/a-look-at-the-samsung-galaxy-j7-prime-smartphone/
HEV Modelling & Optimization_Deepak_PraveenPraveen S R
1. The document discusses modeling and optimizing a 2015 Honda Accord hybrid vehicle.
2. It involves analyzing existing test data to determine the vehicle's control strategy, modeling the vehicle for a 1.4 UDDS test cycle, and optimizing the parallel mode region.
3. The optimization aims to modify the speed and torque of the parallel mode region in the highway test cycle data to deduce an improvement in miles per gallon.
1. The document describes a study that used finite element analysis to simulate the burst pressure of a vibration welded plastic vessel and determine the yield stress at the weld bead.
2. An experimental hydrostatic pressure test showed rupture occurred at the weld bead, so the goal was to model this and obtain the stress at the weld bead.
3. Various meshing techniques were tested in the FEA software ABAQUS to find the best correlation with experimental data, including different element types, sizes, and modeling of the weld bead. The results showed second order elements with two layers of dragged elements for the weld bead membrane provided the most accurate stresses at the weld bead.
A closer look at samsung galaxy j7 primeHouse of IT
Here's an infographic of the cool features you can expect from Samsung's Galaxy J7.
https://houseofit.ph/a-look-at-the-samsung-galaxy-j7-prime-smartphone/
HEV Modelling & Optimization_Deepak_PraveenPraveen S R
1. The document discusses modeling and optimizing a 2015 Honda Accord hybrid vehicle.
2. It involves analyzing existing test data to determine the vehicle's control strategy, modeling the vehicle for a 1.4 UDDS test cycle, and optimizing the parallel mode region.
3. The optimization aims to modify the speed and torque of the parallel mode region in the highway test cycle data to deduce an improvement in miles per gallon.
1. The document describes a study that used finite element analysis to simulate the burst pressure of a vibration welded plastic vessel and determine the yield stress at the weld bead.
2. An experimental hydrostatic pressure test showed rupture occurred at the weld bead, so the goal was to model this and obtain the stress at the weld bead.
3. Various meshing techniques were tested in the FEA software ABAQUS to find the best correlation with experimental data, including different element types, sizes, and modeling of the weld bead. The results showed second order elements with two layers of dragged elements for the weld bead membrane provided the most accurate stresses at the weld bead.
The document describes a hydraulic arm supporter device designed to assist patients recovering from stroke. It consists of an actuator connected to an adjustable arm supporter. The actuator uses hydraulic pressure to raise the arm supporter and angle the patient's arm, helping them perform tasks. It is portable and adjustable to suit different arm lengths. The device is intended to motivate patients by allowing independent exercise of their affected arm through daily activities. Calculations are provided to size the hydraulic actuator components to safely support the needed forces. Drawings and diagrams illustrate the device design and range of motion.
The document provides a report on analyzing and optimizing the manufacturing system of a client company called KCP technologies Private Ltd. Key points:
- The company manufactures screw pump rotors in a batch production process using 3 CNC workstations.
- Cycle times for the two main products were recorded to calculate production rates. Motion studies were conducted to optimize workstation layouts and reduce travel times.
- The current number of workstations was found to be optimal. Modifications like rearranging tools saved an estimated 1 minute per part produced.
- Further analyses included machine cluster possibilities and quality assurance processes to improve the system.
This document discusses a stress contour analysis for an assembly that is missing. A force-displacement plot is mentioned but no other details are provided. The document contains very little contextual information to summarize.