This document provides instructions for removing and installing the hydraulic tank on a lift truck. Key steps include draining the hydraulic oil, disconnecting hoses and cables, removing mounting hardware, and lifting the tank off the frame. The tank should be inspected for cracks, leaks or other damage before cleaning and reinstallation. Safety precautions are outlined due to potential fire hazards from hydraulic fluid vapors.
Hyster g007 (h250 hd) forklift service repair manualusfjjsjekkemm
This document provides instructions for removing and installing the hydraulic tank on Hyster lift trucks. Key steps include draining the hydraulic oil from the tank, disconnecting hoses and electrical connections, and removing mounting hardware. The tank should be cleaned and inspected for leaks before reinstallation. Proper safety precautions are outlined, including disconnecting battery cables and using approved cleaning solutions and welding practices.
Hyster g007 (h210 hd) forklift service repair manualfujdwjjsekkemme
This document provides instructions for servicing the hydraulic tank on Hyster lift trucks. It describes how to remove the tank by disconnecting hoses and electrical connections, draining the fluid, and removing mounting hardware. It also provides cleaning and repair instructions for the tank, including preparing it for welding. The installation instructions describe reconnecting all hoses and mounting the tank back onto the lift truck frame. Safety precautions are provided throughout to warn of hazards like sparks near flammable vapors.
Hyster g019 (h14.00 xm europe) forklift service repair manualusuejjskkemme
This document provides instructions for servicing the hydraulic tank on a lift truck. The key steps are:
1. Drain the hydraulic oil from the tank and disconnect all hoses and electrical connections.
2. Remove the tank from the frame by taking off mounting bolts and nuts.
3. Inspect and clean the tank if needed, being careful of flammable vapors. Welding repairs require special precautions.
4. Reinstall the tank by reversing the removal steps, and refill the hydraulic oil.
This workshop manual provides information for repairing Hino Trucks models 238, 258LP, 268, 338 series equipped with J08E-VB and J08E-VC engines. It contains chapters covering various vehicle systems from the clutch and transmission to brakes, steering, and electrical equipment. Instructions are given for safe vehicle lifting and repair procedures. Torque specifications and recommended lubricants are also included, as well as an information display guide and symptom simulation instructions.
Hyster k005 (h3.50 xm europe) forklift service repair manualfjsjefksekkksemm
The document provides instructions for repairing various components of a lift truck including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant before removing the radiator, and notes the need to add coolant after installation. Safety warnings are provided throughout regarding putting the lift truck on blocks and adding additional blocks when removing heavy components to maintain stability.
The document provides instructions for repairing various components of an industrial lift truck, including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant before removing the radiator, and notes the need to add coolant after installation. Safety warnings are provided throughout regarding the need to stabilize the lift truck during component removal to prevent tipping.
Hyster h177 (h3.20 xm) forklift parts catalogue manualfjsjefksekkksemm
This document is a parts manual for a Challenger H2.00-H3.20XM truck. It is divided into 13 sections covering the frame, engines, fuel system, electrical system, transmission, steering, brakes, hydraulics, mast systems, and options. Section 1 covers the frame and includes diagrams and part numbers for components of the frame and floorplates.
Hyster g007 (h250 hd) forklift service repair manualfjsjefksekkksemm
This document provides instructions for removing and installing major components on a Hyster lift truck, including the air cleaner, exhaust system, hood assembly, and hydraulic tank. The removal and installation procedures are described in step-by-step format with accompanying diagrams and part labels. Safety warnings are included throughout regarding preventing sparks and supporting heavy components during the repair process.
Hyster g007 (h250 hd) forklift service repair manualusfjjsjekkemm
This document provides instructions for removing and installing the hydraulic tank on Hyster lift trucks. Key steps include draining the hydraulic oil from the tank, disconnecting hoses and electrical connections, and removing mounting hardware. The tank should be cleaned and inspected for leaks before reinstallation. Proper safety precautions are outlined, including disconnecting battery cables and using approved cleaning solutions and welding practices.
Hyster g007 (h210 hd) forklift service repair manualfujdwjjsekkemme
This document provides instructions for servicing the hydraulic tank on Hyster lift trucks. It describes how to remove the tank by disconnecting hoses and electrical connections, draining the fluid, and removing mounting hardware. It also provides cleaning and repair instructions for the tank, including preparing it for welding. The installation instructions describe reconnecting all hoses and mounting the tank back onto the lift truck frame. Safety precautions are provided throughout to warn of hazards like sparks near flammable vapors.
Hyster g019 (h14.00 xm europe) forklift service repair manualusuejjskkemme
This document provides instructions for servicing the hydraulic tank on a lift truck. The key steps are:
1. Drain the hydraulic oil from the tank and disconnect all hoses and electrical connections.
2. Remove the tank from the frame by taking off mounting bolts and nuts.
3. Inspect and clean the tank if needed, being careful of flammable vapors. Welding repairs require special precautions.
4. Reinstall the tank by reversing the removal steps, and refill the hydraulic oil.
This workshop manual provides information for repairing Hino Trucks models 238, 258LP, 268, 338 series equipped with J08E-VB and J08E-VC engines. It contains chapters covering various vehicle systems from the clutch and transmission to brakes, steering, and electrical equipment. Instructions are given for safe vehicle lifting and repair procedures. Torque specifications and recommended lubricants are also included, as well as an information display guide and symptom simulation instructions.
Hyster k005 (h3.50 xm europe) forklift service repair manualfjsjefksekkksemm
The document provides instructions for repairing various components of a lift truck including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant before removing the radiator, and notes the need to add coolant after installation. Safety warnings are provided throughout regarding putting the lift truck on blocks and adding additional blocks when removing heavy components to maintain stability.
The document provides instructions for repairing various components of an industrial lift truck, including the counterweight, hood, overhead guard, LED lights, operator restraint system, radiator, and exhaust system. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant before removing the radiator, and notes the need to add coolant after installation. Safety warnings are provided throughout regarding the need to stabilize the lift truck during component removal to prevent tipping.
Hyster h177 (h3.20 xm) forklift parts catalogue manualfjsjefksekkksemm
This document is a parts manual for a Challenger H2.00-H3.20XM truck. It is divided into 13 sections covering the frame, engines, fuel system, electrical system, transmission, steering, brakes, hydraulics, mast systems, and options. Section 1 covers the frame and includes diagrams and part numbers for components of the frame and floorplates.
Hyster g007 (h250 hd) forklift service repair manualfjsjefksekkksemm
This document provides instructions for removing and installing major components on a Hyster lift truck, including the air cleaner, exhaust system, hood assembly, and hydraulic tank. The removal and installation procedures are described in step-by-step format with accompanying diagrams and part labels. Safety warnings are included throughout regarding preventing sparks and supporting heavy components during the repair process.
Hyster e114 (e25 z) forklift service repair manualfjsjefksekkksemm
This document provides a description and repair procedures for a steering housing and steering control unit. It describes the main components of the steering system, including the steering column, steering control unit, and steering housing. The steering housing holds the steering column and control unit, and can be adjusted for operator comfort. The steering control unit is a rotary valve that controls oil flow to the steering cylinder during operation, directing the steer tires. Even without the steering pump operating, limited steering is still possible through a check valve.
Hyster d114 (e1.75 xm europe) forklift service repair manualfjsjefksekkksemm
This document provides specifications and torque values for various components of a service repair for an electric forklift model. It includes specifications for the hydraulic system, wheels and tires, mast speeds, battery specifications, and torque values. Key details include relief pressures for the lift, tilt, auxiliary and steering systems, torque values for drive wheel bolts and steer wheel nuts, standard and optional tire sizes, battery compartment sizes and maximum heights for different battery types, maximum carriage and tilt creep rates, and mast lifting and lowering speeds under different load conditions.
Hyster d098 (e80 z) forklift service repair manualfjsjefksekkksemm
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment prevent battery movement and must be adjusted properly.
- The overhead guard, hood, seat, and battery restraint are removed and installed following specific procedures.
- The counterweight
Hyster c108 (e2.50 xl europe) forklift service repair manualfjsjefksekkksemm
This document provides information about steering systems for electric lift trucks. It describes the components of power steering and power steering with on-demand systems. The key components are the steering wheel, optical encoder, activator, steering control unit, steering pump motor, steering pump, and hydraulic steering motor or steering cylinder. It also provides repair instructions for components like the steering wheel and column assembly.
Hyster c008 (h650 c) forklift service repair manualfjsjefksekkksemm
1) The document provides information about repairing various types of gear pumps, including single-stage and tandem pumps. It describes the basic components and operation of gear pumps.
2) The repair procedures include removing the pump, disassembling it, cleaning and inspecting parts, and assessing wear on gears, shafts, and housings. Proper part orientation and seal positioning is important when reassembling the pump.
3) Worn or damaged seals are a common cause of pump failure. The document provides guidance on inspecting seals and determining if they are too hard, soft, or damaged from high temperatures.
Hyster c004 (s120 e) forklift service repair manualfjsjefksekkksemm
This document provides instructions for servicing and repairing steering axles on various lift truck models. It describes the components of the steering axle assembly and different types of pivot mounts used. Procedures are provided for removing and installing steering axles with stub shaft mounts and rubber mounts. The document also provides instructions for removing and servicing wheel hubs, spindles, bearings and tie rods. Safety warnings are given for putting lift trucks on blocks or stands when performing maintenance.
Hyster b024 (s155 xl2) forklift service repair manualfjsjefksekkksemm
This document provides repair procedures for differentials. It describes the typical components of a differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures explain how to remove the differential carrier from the axle housing, disassemble the differential assembly into its main components, and remove the drive pinion and pinion carrier. Detailed steps are provided for tasks like draining fluids, removing mounting hardware, and using presses and pullers to separate parts while taking safety precautions.
Cummins onan generator set with power command 3100 controller model (dqaa ) s...fjsjefksekkksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbf ) s...fjsjefksekkksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbc ) s...fjsjefksekkksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Case tv370 tier 4 b (final) alpha series compact track loader service repair ...fjsjefksekkksemm
This document provides instructions for locking the loader arms and tilting the cab on radial lift skid steer and compact track loaders. It warns of crushing hazards and outlines safety procedures, including never entering or exiting the cab while the loader arms are raised and unsupported. It instructs having two people, with one removing the support strut while the operator remains in the cab.
Case sv340 tier 4b (final) alpha series skid steer loader service repair manu...fjsjefksekkksemm
This document is a service manual that provides maintenance and repair instructions for SR270/SV340 skid steer loaders and TR340/TV380 compact track loaders with Tier 4B engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. Safety information and instructions are provided at the beginning, along with information on torque specifications, basic shop and assembly instructions, fluids and lubricants, and product identification. Repair and maintenance should only be performed by qualified
Case sv250 tier 4 a alpha series skid steer loader service repair manual pin ...fjsjefksekkksemm
This document is a service manual for Case skid steer loaders and compact track loaders. It provides information on safety procedures, torque specifications, product identification, and maintenance of the engine, front axle, rear axle, and other systems. The document contains copyright information, part numbers, and replaces prior service manuals. It instructs technicians to follow procedures carefully when servicing equipment.
Case sr240 tier 4 b (final) and stage iv alpha series skid steer loader servi...fjsjefksekkksemm
This document is a service manual for skid steer loaders and compact track loaders. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork, and decals. The introduction provides important safety notices for equipment servicing and lists the models covered.
Case sr240 tier 4 b (final) alpha series skid steer loader service repair manualfjsjefksekkksemm
This document is a service manual that covers safety procedures, specifications, repair and maintenance instructions for Case Construction skid steer loaders and compact track loaders, including the SR210, SR240, SV280, TR270, and TR310 models. It addresses topics like the engine, fuel system, exhaust system, cooling system, lubrication system, hydraulic systems, electrical systems, cab controls, and more. Safety is emphasized, and qualified service personnel following the proper procedures are required for repairs. Specifications are provided.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Hyster e114 (e25 z) forklift service repair manualfjsjefksekkksemm
This document provides a description and repair procedures for a steering housing and steering control unit. It describes the main components of the steering system, including the steering column, steering control unit, and steering housing. The steering housing holds the steering column and control unit, and can be adjusted for operator comfort. The steering control unit is a rotary valve that controls oil flow to the steering cylinder during operation, directing the steer tires. Even without the steering pump operating, limited steering is still possible through a check valve.
Hyster d114 (e1.75 xm europe) forklift service repair manualfjsjefksekkksemm
This document provides specifications and torque values for various components of a service repair for an electric forklift model. It includes specifications for the hydraulic system, wheels and tires, mast speeds, battery specifications, and torque values. Key details include relief pressures for the lift, tilt, auxiliary and steering systems, torque values for drive wheel bolts and steer wheel nuts, standard and optional tire sizes, battery compartment sizes and maximum heights for different battery types, maximum carriage and tilt creep rates, and mast lifting and lowering speeds under different load conditions.
Hyster d098 (e80 z) forklift service repair manualfjsjefksekkksemm
This document provides descriptions and service procedures for parts of an electric forklift frame, including the frame, counterweight assembly, overhead guard, hood and seat assembly, access panels, and label positions. It also describes removing the traction motor. Key points include:
- The frame is a single weldment that mounts other components like the counterweight, overhead guard, steering and drive axles.
- Floor plates and panels can be removed for access to hydraulic and electrical systems.
- Spacers in the battery compartment prevent battery movement and must be adjusted properly.
- The overhead guard, hood, seat, and battery restraint are removed and installed following specific procedures.
- The counterweight
Hyster c108 (e2.50 xl europe) forklift service repair manualfjsjefksekkksemm
This document provides information about steering systems for electric lift trucks. It describes the components of power steering and power steering with on-demand systems. The key components are the steering wheel, optical encoder, activator, steering control unit, steering pump motor, steering pump, and hydraulic steering motor or steering cylinder. It also provides repair instructions for components like the steering wheel and column assembly.
Hyster c008 (h650 c) forklift service repair manualfjsjefksekkksemm
1) The document provides information about repairing various types of gear pumps, including single-stage and tandem pumps. It describes the basic components and operation of gear pumps.
2) The repair procedures include removing the pump, disassembling it, cleaning and inspecting parts, and assessing wear on gears, shafts, and housings. Proper part orientation and seal positioning is important when reassembling the pump.
3) Worn or damaged seals are a common cause of pump failure. The document provides guidance on inspecting seals and determining if they are too hard, soft, or damaged from high temperatures.
Hyster c004 (s120 e) forklift service repair manualfjsjefksekkksemm
This document provides instructions for servicing and repairing steering axles on various lift truck models. It describes the components of the steering axle assembly and different types of pivot mounts used. Procedures are provided for removing and installing steering axles with stub shaft mounts and rubber mounts. The document also provides instructions for removing and servicing wheel hubs, spindles, bearings and tie rods. Safety warnings are given for putting lift trucks on blocks or stands when performing maintenance.
Hyster b024 (s155 xl2) forklift service repair manualfjsjefksekkksemm
This document provides repair procedures for differentials. It describes the typical components of a differential assembly, including the housing, ring and pinion gear set, and differential assembly. The procedures explain how to remove the differential carrier from the axle housing, disassemble the differential assembly into its main components, and remove the drive pinion and pinion carrier. Detailed steps are provided for tasks like draining fluids, removing mounting hardware, and using presses and pullers to separate parts while taking safety precautions.
Cummins onan generator set with power command 3100 controller model (dqaa ) s...fjsjefksekkksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbf ) s...fjsjefksekkksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Cummins onan generator set with power command 3100 controller model (dfbc ) s...fjsjefksekkksemm
This document is a service manual that provides information for troubleshooting and servicing generator sets and their components. It includes sections on control operation, circuit boards and modules, troubleshooting, control service and calibration, servicing the generator, day tank fuel transfer pumps, optional enclosure fuel tank systems, and wiring diagrams. The manual provides technical specifications and maintenance procedures for various generator set parts.
Case tv370 tier 4 b (final) alpha series compact track loader service repair ...fjsjefksekkksemm
This document provides instructions for locking the loader arms and tilting the cab on radial lift skid steer and compact track loaders. It warns of crushing hazards and outlines safety procedures, including never entering or exiting the cab while the loader arms are raised and unsupported. It instructs having two people, with one removing the support strut while the operator remains in the cab.
Case sv340 tier 4b (final) alpha series skid steer loader service repair manu...fjsjefksekkksemm
This document is a service manual that provides maintenance and repair instructions for SR270/SV340 skid steer loaders and TR340/TV380 compact track loaders with Tier 4B engines. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork and decals. Safety information and instructions are provided at the beginning, along with information on torque specifications, basic shop and assembly instructions, fluids and lubricants, and product identification. Repair and maintenance should only be performed by qualified
Case sv250 tier 4 a alpha series skid steer loader service repair manual pin ...fjsjefksekkksemm
This document is a service manual for Case skid steer loaders and compact track loaders. It provides information on safety procedures, torque specifications, product identification, and maintenance of the engine, front axle, rear axle, and other systems. The document contains copyright information, part numbers, and replaces prior service manuals. It instructs technicians to follow procedures carefully when servicing equipment.
Case sr240 tier 4 b (final) and stage iv alpha series skid steer loader servi...fjsjefksekkksemm
This document is a service manual for skid steer loaders and compact track loaders. It contains sections on the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, and platform, cab, bodywork, and decals. The introduction provides important safety notices for equipment servicing and lists the models covered.
Case sr240 tier 4 b (final) alpha series skid steer loader service repair manualfjsjefksekkksemm
This document is a service manual that covers safety procedures, specifications, repair and maintenance instructions for Case Construction skid steer loaders and compact track loaders, including the SR210, SR240, SV280, TR270, and TR310 models. It addresses topics like the engine, fuel system, exhaust system, cooling system, lubrication system, hydraulic systems, electrical systems, cab controls, and more. Safety is emphasized, and qualified service personnel following the proper procedures are required for repairs. Specifications are provided.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. 100 SRM 1349 Description
General
This section has the removal and installation in-
structions for major assemblies attached to the
frame. The removal and installation procedures
for some assemblies are described in the following
service manuals:
• Operator’s Cab 100 SRM 1100
• Multiple Aligned Cooling System 700 SRM
1350
• Planetary Drive Axle, (Wet System) 1400 SRM
944
• Planetary Drive Axle, (Dry System) 1400 SRM
945
• Steering System 1600 SRM 1365
• Hydraulic System 1900 SRM 938
• Masts and Carriages, Starting 2003 4000 SRM
1062
Description
CAUTION
Do not initiate repairs to the frame without
consulting a Hyster service representative or
damage to the lift truck may occur.
The frame is a weldment with mounts for the major
assemblies. See Figure 1. The mounts are designed
to keep the attaching parts in position and transfer
the normal forces acting on them.
1. TILT CYLINDER MOUNT
2. MAIN FRAME
3. MAST MOUNT
4. DRIVE AXLE MOUNT
5. SIDE TILTING CAB MOUNT
6. FUEL/HYDRAULIC TANK MOUNT
7. TRANSMISSION MOUNT
8. MAIN COUNTERWEIGHT MOUNT
9. STEER AXLE MOUNT
10. ENGINE MOUNT
11. MAIN CONTROL VALVE MOUNT
Figure 1. Frame
1
3. Air Cleaner 100 SRM 1349
Air Cleaner
REMOVE
1. Open the left- and right-hand hood.
2. Loosen the air duct clamp. See Figure 2.
3. Close the left- or right-hand hood to access the
precleaner.
4. Remove the precleaner, with the air duct at-
tached, from the air cleaner.
5. Disconnect the connector from the restriction in-
dicator by pressing the metal clip.
6. Remove the hose clamp from the air filter hose
and remove the hose from the air cleaner.
7. Remove the bolts of the two mounting clamps.
8. Rotate the air cleaner until the air duct connec-
tion is clear from the center of the hood opening
and remove the air cleaner to the right-hand side
of the truck.
9. Remove the retaining hardware from the mount-
ing clamps and remove the clamps and plate po-
sitioned under the hood.
INSTALL
1. Install the retaining hardware to the mounting
clamps and install the clamps and plate posi-
tioned under the hood.
2. Position the air cleaner assembly at the mount-
ing clamps and tighten the two clamp bolts.
3. Connect the air filter hose to the air cleaner as-
sembly and tighten the hose clamp.
4. Connect the restriction indicator connector to the
air cleaner assembly.
5. Close the left- or right-hand hood.
6. Install the precleaner, with the air duct attached,
on the air cleaner and tighten the air duct clamp.
7. Close the hoods.
1. PRECLEANER
2. CAPSCREW
3. HOSE CLAMP
4. CLAMP BOLT
5. MOUNTING CLAMP
6. AIR FILTER HOSE
7. AIR CLEANER ASSEMBLY
8. RESTRICTION INDICATOR
9. AIR DUCT CLAMP
10. AIR DUCT
Figure 2. Air Cleaner
2
4. 100 SRM 1349 Exhaust System
Exhaust System
REMOVE
WARNING
Exhaust system must be at room temperature
before starting disassembly or personal injury
may occur.
1. Remove the two clamps from the flex tube. See
Figure 3.
2. Remove the clamp that connects the turbo charge
pipe to the exhaust pipe.
3. Remove the clamp that holds the exhaust pipe to
the engine and remove the exhaust pipe and flex
tube.
4. Affix a tool that will retain the nut when loosen-
ing a capscrew of the muffler. Remove the four
capscrews and nuts.
5. Remove the muffler from the hood.
INSTALL
1. Position the muffler at the hood.
2. Install the four capscrews and nuts of the muf-
fler.
3. Install the flex tube and two clamps to the muf-
fler.
4. Install the exhaust pipe and exhaust pipe clamp
to the engine.
5. Install the clamp that connects the turbo charge
pipe to the exhaust pipe.
6. Tighten all clamps.
1. MUFFLER
2. CAPSCREWS
3. CLAMP
4. FLEX TUBE
5. EXHAUST PIPE
6. CLAMP
Figure 3. Exhaust System
3
5. Hood Assembly 100 SRM 1349
Hood Assembly
REMOVE
1. Tilt the mast completely forward.
2. Completely tilt (raise) the cab.
3. Open the rear cover. See Figure 4.
1. REAR COVER
2. HOOD FRAME
3. MUFFLER
4. LEFT-HAND HOOD
5. HINGE
6. FRONT HOOD COVER
7. RIGHT-HAND HOOD
Figure 4. Hood Assembly
4. Remove the bolts from the two isolators on top of
the radiator. See Figure 5.
5. Remove the four capscrews that hold the bracket
of the hood assembly to the counterweight.
6. Disconnect the two gas springs from the rear
cover at the counterweight.
7. Open the left- and right-hand hood.
8. Remove the exhaust pipe, flex tube, and U-bolt.
1. RADIATOR
2. BOLT
3. WASHER
4. ISOLATOR
5. BRACKET
6. LEFT-HAND HOOD
7. HOOD FRAME
Figure 5. Top Isolators
9. Remove the inlet suction tube.
10. Remove the two capscrews, washers, and nuts
and remove the expansion tank located under-
neath the hood.
11. Place the expansion tank inside the engine com-
partment.
12. Remove all tie-wraps holding electrical cables to
the hood covers or hood assembly.
NOTE: Step 13 is for LPG (Liquefied Petroleum Gas)
engines only.
13. Remove the two hose clamps and crankcase
breather hoses from the front hood cover and
remove the crankcase breather.
14. Remove the two nuts that hold the front hood
cover to the frame.
15. Attach a lifting device to the hood assembly.
4
6. 100 SRM 1349 Hydraulic Tank
CAUTION
Use caution when lifting the hood assembly to
avoid damage to the rear of the operators cab.
16. Lift the hood assembly from the frame and place
it on the ground in a horizontal position by
putting a support under the rear of the hood
frame.
INSTALL
1. Attach a lifting device to the hood assembly.
CAUTION
Use caution when installing the hood assembly
to avoid damage to the rear of the operators
cab.
2. Position the hood assembly onto the frame.
3. Install the two nuts that hold the front hood cover
to the frame.
NOTE: Step 4 is for LPG engines only.
4. Install the crankcase breather and breather
hoses to the front hood cover with the two hose
clamps.
5. Attach the electrical cables at the original loca-
tions to the hood assembly with tie-wraps.
6. Install the expansion tank under the hood with
the two capscrews, washers, and nuts.
7. Install the inlet suction tube. See the section Air
Cleaner, Install.
8. Install the exhaust pipe, flex tube, and U-bolt.
See the section Exhaust System, Install.
9. Install the four capscrews that hold the hood as-
sembly to the counterweight.
10. Install the two gas springs to the rear cover at
the counterweight.
11. Attach the radiator to the bracket of the hood
assembly. See Figure 5.
12. Close the left- and right- hand hood.
13. Completely lower the cab.
14. Start the engine and check for leaks.
Hydraulic Tank
The hydraulic tank is installed on the right side of the
frame between the front fender and counterweight.
REMOVE
NOTE: The hydraulic tank removal and installation
must be done with aid of an assistant.
1. Place the truck on a solid, level surface.
2. Lower the mast completely.
3. Shut down the engine.
4. Apply the parking brake.
5. Remove the four capscrews (3) and washers (4)
holding the right-hand panel on top of the hy-
draulic tank and remove the right-hand panel.
See Figure 6.
6. Remove the three capscrews (7) and washers (8)
holding the right-hand extension plate and re-
move the extension plate. See Figure 6.
7. Remove the drain plug at the bottom of the
hydraulic tank and drain the hydraulic oil into
clean containers.
8. Put tags on the four return hoses and pipes at the
top of the hydraulic tank for identification.
NOTE: Use a drain pan to collect the oil from the hy-
draulic hoses.
9. Disconnect the four return hoses from the two
pipes at the top of the hydraulic tank. See Fig-
ure 7.
10. Put caps on the hoses and pipes.
11. Put tags on the two hoses and connections at the
frame side of the hydraulic tank for identifica-
tion.
12. Disconnect the two hoses from the two connec-
tions at the frame side of the hydraulic tank. See
Figure 7.
5
7. Hydraulic Tank 100 SRM 1349
1. HYDRAULIC TANK
2. BATTERY BOX
3. CAPSCREWS
4. WASHERS
5. RIGHT-HAND PANEL
6. SEAL
7. CAPSCREWS
8. WASHERS
9. RIGHT-HAND EXTENSION PLATE
10. BATTERY CABLE ACCESS
Figure 6. Hydraulic Tank
13. Put caps on the hoses and connections on the hy-
draulic tank.
CAUTION
Disconnect the negative (ground) cable first or
lift truck damage may occur.
14. Disconnect the negative (ground) and positive
(power) cables from the batteries.
15. Remove the batteries from the battery box.
16. Remove the battery cables from the access hole
of the hydraulic tank. See Figure 6.
17. Remove the capscrews that hold the right run-
ning board to the counterweight, front fender,
and hydraulic tank and remove the running
board.
18. Remove the anchor that secures the cab tilt shaft.
NOTE: When moving the front cab tilt shaft, main-
tain the position of the shims between the cab and
frame tilt brackets.
19. Use a short rounded 19 mm (0.75 in.) shaft and
hammer it into the front tilt bracket of the cab.
20. Push the cab tilt shaft further rearwards un-
til the shaft slightly protrudes out of the rear
bracket.
6
8. 100 SRM 1349 Hydraulic Tank
1. RETURN PIPE
2. HOSE CONNECTION
3. DRAIN PLUG
Figure 7. Hydraulic Tank Connection and
Fittings
WARNING
Make sure the hydraulic tank is supported
with a hydraulic jack, hand pallet lift, or a lift
truck.
21. Support the hydraulic tank with blocks of at least
50 mm (2.0 in.) thick to cover the height of the
bracket at the bottom of the hydraulic tank.
22. Remove the three nuts and washers that hold the
hydraulic tank to the frame.
CAUTION
DO NOT to damage the studs during removal of
the hydraulic tank from the frame.
23. Lift the hydraulic tank from the studs and move
the hydraulic tank away from the frame.
INSPECT
WARNING
Do not use tools that can make sparks, heat, or
static electricity. The vapors in the tank can
cause an explosion.
Make a visual inspection of all sides of the tank. In-
spect the welds for cracks and leakage. Check for
wet areas, accumulation of dirt, and loose or miss-
ing paint caused by leakage. Areas of the tank that
are not easily seen can be checked with an inspection
mirror and a light that is approved for locations with
flammable vapors.
CLEAN
Tank can be cleaned with or without steam. If steam
is available use a hose with a minimum diameter of
19 mm (0.75 in.). Control the pressure of the steam
by a valve installed at the nozzle of the hose. If a
metal nozzle is used, it must be made of a material
that does not make sparks. Make an electrical con-
nection between the nozzle and the tank. Connect a
ground wire to the tank to prevent static electricity.
1. Remove all the parts from the tank. Install the
drain plug.
WARNING
When cleaning the tank, do not use solutions
that make dangerous gases at normal temper-
atures or when heated. Wear eye and face pro-
tection. Protect the body from burns. If the
tank is cleaned inside a building, make sure
there is enough ventilation.
CAUTION
Disposal of lubricants, fluids, and chemicals
must meet local environmental regulations.
2. Fill the tank with a cleaning solution. Proceed as
follows:
• If steam is available, fill the tank 1/4 full with
a solution of water and sodium bicarbonate or
sodium carbonate. Mix 0.5 kg (1 lb) per 4 liter
(1 gal).
• If the tank cannot be cleaned with steam, mix
a solution of water and trisodium phosphate
or cleaning compound with an alkaline base.
Follow the instructions given by the manufac-
turer.
7
9. Thank you very much
for your reading. Please
Click Here Then Get
More Information.
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
10. Hydraulic Tank 100 SRM 1349
WARNING
Compressed air can move particles so that they
cause injury to the user or to other personnel.
Make sure that the path of the compressed air
is away from all personnel. Wear protective
goggles or a face shield to prevent injury to the
eyes.
3. Mix the solution in the tank using air pressure.
Make sure all the surfaces on the inside of the
tank are flushed with the solution.
4. Drain the tank.
5. If steam is available, put steam into the tank un-
til the tank does not have odors and the metal is
hot. Steam vapors must come from all the open-
ings.
6. Flush the inside of the tank with boiling water.
Make sure all the loose material and cleaning
compound is removed from the inside of the tank.
7. Make an inspection of the inside of the tank. If it
is not clean, repeat Step 5 and Step 6 and make
another inspection. When making inspections,
use a light that is approved for locations with
flammable vapors.
8. Check the tank for flammable vapors. Put plugs
in all the openings in the tank. Wait 15 minutes,
then remove the inlet and outlet plugs. Test a
sample of the vapor with a special indicator for
gas vapors. If the amount of flammable vapors
is above the lower flammable limit, repeat the
cleaning procedures.
ADDITIONAL PREPARATIONS FOR
REPAIR
If nitrogen gas or carbon dioxide gas is available, pre-
pare the cleaned tank for welding using these gases.
See the manual Safe Practices for Welding and Cut-
ting Containers That Have Held Combustibles by the
American Welding Society, F4.1-1999.
If these gases are not available, fill the tank with
water to just below the point where the work will
be done. Make sure the space above the level of the
water has a vent.
REPAIR
Small Leaks
Use the following procedure to repair small leaks:
1. Use steam to clean the area around the leak. Re-
move all paint and dirt around the leak.
2. Apply Loctite® 290 to the leak. Follow the in-
structions of the manufacturer.
Large Leaks
WARNING
Special procedures must be followed when
large leaks or other repairs need welding or
cutting. All work must be done by authorized
personnel.
CAUTION
Welding on the truck may cause damage to the
engine, transmission, and/or hydraulic elec-
tronic control units if proper precautions are
not taken. Disconnect the negative battery ter-
minal from the battery. Disconnect all ECM’s.
If welding must be done in a close proximity
of an ECM, that ECM must be removed. When
welding to the chassis, attach the ground cable
as close the weld as possible.
1. Use the procedure described under Clean to pre-
pare the tank for repairs.
2. Contact your dealer for Hyster lift trucks for
welding instructions.
3. Use acceptable welding practices to repair the
tank. See the American National Standard
Safety in Welding and Cutting, AWS Z 49.1 -
1999.
Preparations for use After Repair
1. Add more water to the tank so that the water
goes above the point of where the work was done.
Check to see if there are any leaks coming from
tank.
2. If there are no leaks coming from the tank, re-
move all the water from the tank.
8
11. 100 SRM 1349 Hydraulic Tank
INSTALL
NOTE: When installing the hydraulic system oil fil-
ter, it is important to grease the O-ring before instal-
lation.
1. Place the hydraulic tank on lifting equipment
and support with blocks of at least 50 mm
(2.00 in.) thick to cover the height of the bracket
at the bottom of the hydraulic tank.
2. Raise and place the hydraulic tank in front of
the right side of the frame in the correct height
position.
CAUTION
DO NOT to damage the studs during installa-
tion of the hydraulic tank to the frame.
3. Careful place the hydraulic tank over the studs
without damaging the studs.
4. Install the three washers and nuts that hold the
top of the hydraulic tank to the frame.
5. Remove the lifting device.
NOTE: While pushing the cab tilt shaft to the front of
the truck, keep the shims in their position between
the cab and cab tilt system.
6. Push the cab tilt shaft towards the front of the
truck and guide the shaft into the front bracket.
7. Install the anchor that secures the cab tilt shaft.
8. Inspect the right running board grommets. Re-
place if damaged.
9. Put the right running board in place and install
the capscrews that hold the running board to the
counterweight, front fender, and hydraulic tank.
10. Install the right-hand extension plate using the
three capscrews and washer. See Figure 6.
11. Feed the battery cables through the access hole
of the hydraulic tank. See Figure 6.
12. Install the batteries into the battery box.
CAUTION
Connect the positive (power) cable first or lift
truck damage may occur.
13. Connect the positive (power) and negative
(ground) cables to the batteries.
14. Connect the two hoses to the two connections at
the frame side of the hydraulic tank.
15. Connect the four return hoses to the two pipes at
the top of the hydraulic tank. Torque the large
fittings to 88 to 98 N•m (65 to 72 lbf ft).
16. Make sure the drain plug is installed at the bot-
tom of the hydraulic tank.
17. Use a filtration system when refilling the hy-
draulic tank to the correct level with the oil spec-
ified in the maintenance table. See the section
Periodic Maintenance 8000 SRM 1347.
18. Start the engine and operate the hydraulic sys-
tem.
19. Make sure all functions work correctly.
WARNING
Do not try to locate hydraulic leaks by putting
hands on pressurized hydraulic components.
Hydraulic oil can be injected into the body and
cause personal injury.
20. Check for leaks.
21. Bleed the system.
22. If necessary, fill the hydraulic tank to the correct
level after bleeding the system.
23. Position the right-hand panel on top of the hy-
draulic tank and install the four washers and
capscrews.
9
12. Fuel Tank 100 SRM 1349
Fuel Tank
The fuel tank is installed on the left side of the frame
between the front fender and counterweight.
The LPG version has a cover instead of a fuel tank.
This cover can be replaced in a similar way.
REMOVE
1. Place the truck on a solid, level surface.
2. Lower the mast completely.
3. Shut down the engine.
4. Apply the parking brake.
5. Completely tilt (Raise) the cab.
6. Remove the connector from the pushbutton
switch at the left-hand panel.
7. Remove the four capscrews and washers holding
the left-hand panel and remove the panel.
8. Remove the left-hand extension plate between
the fuel tank and counterweight.
WARNING
When removing the fuel tank, do not use tools
that can make sparks, heat, or static electricity.
The vapors in the tank can cause an explosion
and personal injury may occur.
9. Put a drain pan under the fuel tank.
10. Remove the drain plug to drain the fuel from the
tank. See Figure 8.
WARNING
If fuel is drained, put the fuel in a can or barrel
that has a protected seal cap.
11. Disconnect the fuel sender connector at the top
of the fuel tank. See Figure 8.
12. Put tags on the check valve and shutoff valve fuel
hoses and fittings for identification.
NOTE: Use a drain pan to catch the fuel in the fuel
hoses.
13. Disconnect the two fuel hoses from the check
valve and shutoff valve at the top of the fuel
tank. See Figure 8.
14. Put caps on the fuel hoses and fittings.
15. Remove the check valve and shut off valve at the
top of the fuel tank. See Figure 8.
16. Put caps on the fittings at the top of the fuel tank.
17. Loosen the fuel hose clamp located on top of the
frame.
18. Turn the ends of the hoses parallel with the
frame.
19. Remove the hose clamp for the cab tilt hoses.
20. Remove the retaining hardware of the left- and
right-hand latch located on the frame.
21. Remove the two capscrews, and washers at the
back of the hand pump. See Figure 9.
10
14. Fuel Tank 100 SRM 1349
1. ELECTRICAL TILT PUMP 2. HAND PUMP 3. FUEL TANK
Figure 9. Fuel Tank, Hand Pump, and Electric Lift Pump
22. Remove the capscrews holding the left running
board to the counterweight, front fender, and fuel
tank and remove the running board.
WARNING
Make sure that the lifting device has the rated
capacity of 100 kg (2205 lb)to lift the fuel tank.
NOTE: Removal of the fuel tank can be done with a
lifting device, hydraulic jack, hand pallet jack, or lift
truck.
NOTE: Follow step Step 23 and Step 24 when a lifting
device is used.
NOTE: Follow Step 25 when a hydraulic jack, hand
pallet jack, or lift truck is used.
NOTE: When lifting, keep the fuel tank in the hori-
zontal position.
23. Attach a lifting device to the fuel tank. Attach
lifting eyes at the locations shown in Figure 10.
24. Create slight tension on the chains.
25. Support the fuel tank with blocks of at least
50 mm (2.0 in.) thick to cover the height of the
bracket on the bottom of the fuel tank.
CAUTION
DO NOT to damage the studs during removal of
the fuel tank from the frame.
26. Remove the two nuts and washers that hold the
top of the fuel tank and the electrical tilt pump
bracket to the frame.
12
15. 100 SRM 1349 Fuel Tank
Figure 10. Lifting Points
27. Remove the electrical tilt pump and bracket from
the frame.
28. Place the electrical tilt pump, hand pump, left
and right latch inside the frame to avoid damage
to the hoses during the removal of the fuel tank.
29. Remove the remaining nut that holds the fuel
tank to the frame.
30. Lift the fuel tank from the studs and move the
fuel tank away from the frame.
13
16. Fuel Tank 100 SRM 1349
REPAIR
WARNING
Do not use tools that can make sparks, heat, or
static electricity. The vapors in the tank can
cause an explosion.
Repair the fuel tank as described in the section Hy-
draulic Tank.
INSTALL
NOTE: Follow Step 1 when a lifting device is used.
NOTE: Follow Step 2 when a hydraulic jack, hand
pallet jack, or lift truck will be used.
NOTE: When lifting, keep the fuel tank in a horizon-
tal position.
1. Attach a lifting device with lifting straps and lift-
ing eyes to the fuel tank.
2. Place the fuel tank on lifting equipment and sup-
port with blocks of at least 50 mm (2.00 in.) thick
to cover the height of the bracket at the bottom
of the fuel tank.
3. Raise and place the fuel tank in front of the left
side of the frame.
CAUTION
DO NOT to damage the studs during installa-
tion of the fuel tank.
4. Place the fuel tank over the studs of the frame.
5. Install the washer and nut, located behind the
hand pump, that hold the top of the fuel tank to
the frame.
6. Position the hand pump, electrical tilt pump, left
and right latch at the frame and route the hoses
correctly.
7. Install the two washers and nuts that hold the
top of the fuel tank and the electrical tilt pump
bracket to the frame.
8. Install the hand pump with the two washers and
capscrews located behind the hand pump.
9. Install the left and right latch, located at the
frame, with the capscrews, spring washers,
washers, and nuts.
10. Install the hose clamps located on top of the
frame.
11. Inspect the left running board grommets. Re-
place if damaged.
12. Put the left running board in place and install
the capscrews that hold the running board to the
counterweight, front fender, and fuel tank.
13. Install the left hand extension plate between
the fuel tank and counterweight using the three
washers and capscrews.
14. Install the drain plug at the bottom of the fuel
tank.
15. Install the check valve and shutoff valve at the
top of the fuel tank.
16. Connect the two fuel hoses to the check valve and
shut off valve at the top of the fuel tank.
17. Connect the connector to the electrical tilt pump.
18. Connect the connector of the fuel sender to the
top of the fuel tank.
19. Position the left-hand panel on top of the fuel
tank and install the four capscrews and washers.
20. Connect the connector, located at the left-hand
panel, to the push button switch.
21. Fill the fuel tank to the correct level with fuel
specified in the section Periodic Maintenance
8000 SRM 1347.
CAUTION
Connect the positive (power) cable first or lift
truck damage may occur.
22. Connect the positive (power) and negative
(ground) cable to the batteries.
23. Completely lower the cab.
24. Start the engine.
25. Check for leaks.
14
17. 100 SRM 1349 Engine
Engine
REMOVE
WARNING
Engine must be at room temperature before
starting disassembly or personal injury may
occur.
CAUTION
Repairs to air conditioning that require dis-
charging and/or refilling of the refrigeration
fluid must be performed only by a trained and
certified air conditioning specialist.
1. Place the truck on a solid, level surface.
2. Lower the mast completely.
3. Shut down the engine.
4. Apply the parking brake.
5. Completely tilt (Raise) the cab.
CAUTION
Disconnect the negative (ground) cable first or
damage to the lift truck may occur.
6. Disconnect the negative (ground) and positive
(power) cables from the batteries.
7. Remove the hood. See the section Hood Assem-
bly, Remove.
8. Disconnect the electrical cable from the air con-
ditioner compressor.
NOTE: Removing the compressor for the air condi-
tioner with the hoses attached prevents the need to
have a certified specialist suction and refill the air
conditioning system.
NOTE: DO NOT remove the refrigerant hoses.
9. Remove the air conditioner compressor from the
mounting bracket located on the engine.
10. Attach the air conditioner compressor with the
hoses to the cab. Make sure the hoses are free
from the engine/transmission during removal.
11. Put tags on the two heater hoses for identifica-
tion.
12. Disconnect the two heater hoses located under
the operators compartment at the engine side.
13. Put caps on the two heater hoses.
WARNING
DO NOT remove the pressure cap from the ex-
pansion bottle when the engine is hot. When
the pressure cap is removed, the pressure is re-
leased from the system. If the system is hot, the
steam and boiling coolant can cause burns.
CAUTION
Disposal of lubricants and fluids must meet lo-
cal environmental regulations.
14. Let coolant cool to room temperature.
15. Use a drain pan to catch the coolant.
16. Remove the pressure cap from the expansion
tank.
17. Remove the radiator return hose from the engine
to drain the coolant.
NOTE: Use a drain pan to drain the transmission oil
from the transmission.
18. Remove the drain plug at the bottom of the trans-
mission and put the transmission oil in a clean
barrel.
19. Install the drain plug at the bottom of the trans-
mission.
NOTE: Step 20 through Step 25 is for diesel engines
only.
20. Close the fuel shutoff valve at the top of the fuel
tank.
21. Put tags on the fuel hoses and fittings for identi-
fication.
NOTE: Use a drain pan to catch the fuel in the fuel
hoses.
22. Disconnect the fuel hose at the diesel fuel filter.
23. Disconnect the fuel hose at the check valve.
24. Put caps on the fuel hoses and fittings.
25. Attach the fuel hoses to the engine.
15