F.lli Della Marca

FDM
F.lli Della Marca srl

Ultra Freezers -86°C Med

Temperature Range
»» Adjustable inner temperature from -40°C to -86°C.
»» Guaranteed operating temperature of -86°C at +32°C ambient temperature.
Structure
»» External coating and base made of very thick phosphated sheet steel treated with epoxy powder paints in white and
blue colors.
»» The unit is mounted on high resistance castors for an easy displacement.
»» In order to limit the overall dimensions with advantage for the optimization of space within the laboratory, the chest
models with 230 and 390 liters are equipped with the crankcase positioned below the refrigerated chamber.
Thermal insulation
»» Polyurethane foam insulation with high insulating power, free from CFC and HCFC gases, which is high density injected
in-situ to obtain a layer with a thickness of 12 cm in the side walls and 14 cm in the rear wall for the upright models or
else in the bottom wall for the chest models.
Inner chamber
»» Internal coating of stainless steel 18/8 AISI 304.
»» Upright freezers are equipped with stainless steel 18/8 AISI 304, shelves which are adjustable in height and inner doors
each provided with independent closure to minimize the leakage of cold air during the opening of the main door.
»» The chest freezers are equipped with polyurethane inner lids.

F.lli Della Marca S.r.l. Viale Arcangelo Ghisleri 40-42, 00176 - Rome, Italy tel: 06-298042 - fax: 06-273514
www.dellamarca.it - info@dellamarca.it

FDM


Service door
»» Door with a thickness of 10 cm, mounted on steel hinges.
»» The self-balancing hinges are adjustable to assure proper alignment of the door with the main body and then
a correct closure and a perfect seal of the gasket with reduction of the formation of frost and consequent
operations of defrosting.
»» Progressive closing with handle and key lock as standard.
»» Gasket with quadruple step silicone rubber for a perfect seal of the door.
»» Reopening system equipped with an inner pressure compensating valve.

Refrigerant system
»» Completely sealed refrigeration system with two compressors operating with cascade circuit.
»» The freezers are equipped with 0.75 Hp hermetic compressors on 230 liters models and with 1.7 Hp on all other
models.
»» Ecological HFC refrigerant gases CFC and HCFC free.
»» The compressors are equipped with an automatic protection system which protects the compressors in case of
overpressure operating conditions.
»» The static type evaporator is composed of a coil in copper which provides a very efficient thermal exchange,
reduction of frost formation, greater internal volume available, low noise level, low energy consumption and
more compact overall dimensions.
»» The ventilated type air cooled condenser has a increased size to ensure the best performance of the freezer even
at high ambient temperatures. The fan assemblies are equipped with ball bearings to ensure a low noise level
and greater durability.
»» A washable dust filter made of polyester foam protects the condenser from deposits of dust, it can be easily
removed for replacement or for cleaning with washing in water.
»» Manual type of defrost system.

Control instruments
»» Internal temperature is controlled by PLC electronic controllers of latest generation.
»» Temperature display with large semi-graphical LCD display with a resolution of 132x64 pixels.
»» Easy adjustment of the temperature through the easy use of buttons on the front panel.
»» All settings can be inhibited to persons outside using access passwords.
»» Electronic module with level IP65 faceplate protection.
»» Predisposition to the system of data monitoring and/or data recording with RS485 serial interface.
»» The entire control system is equipped with a 12V DC backup battery with auto-charging device which allows the
functioning of the digital display of temperature also in case of lack of electrical current.


FDM


Alerts & Alarms
»» Visual and acoustic temperature alarm alerts the operator if the internal temperature
falls below the preset limit or else if it rises above the expected one. The device is
equipped with a test button, a mute button and a free contact for remote connection.
»» Visual and acoustic hot condenser alarm warns the operator if the condensing
temperature rises above the maximum value set, this may be caused by dust
filter clogged with deposits and therefore it becomes necessary an operation of filter
cleaning. The alarm system is equipped with a button to mute the sound.
»» The entire alarm system is equipped with a 12V DC backup battery with auto-charging
device which allows the the alarm operation also in case of lack of electrical current.
»» Mains power failure alarm alerts the operator if there is a power failure.
»» Low battery alarm will alert you if the 12V DC battery should be replaced.
»» Temperature probes alarm alerts in case of failure of the temperature probes.
»» Opened door alarm warns the operator if the door has been left opened (optional).

Power supply
»» 220/230V 50Hz single phase supply with 16 Amp interlocked socket.
»» Different voltages and frequencies are available on request.

Noise level
»» Noise level less than 58 dB at a distance of one meter, less than 53 dB at three
meters.

Quality Certifications & Compliances
»» EEC Directive 2006/42/EC “Machinery”;
»» EEC Directive 2006/95/EC “Low Voltage”;
»» EEC Directive 2004/108/EC “Electromagnetic compatibility”;
»» CEI 66/5 “Safety requirements for electrical equipment for laboratory use”;
»» The gases used are not flammable and are not considered harmful to the envi-
ronment according to the Montreal Protocol 1987 and subsequent amendments to
London 1990 and Copenhagen 1992, then compliance with the law n ° 549/93 (pro-
tection of the environment from contamination by chlorinated and fluorinated gases
CFC);
»» The quality and safety of our equipment is guaranteed by the system design and
production
»» UNI EN ISO 9001 and the CE mark.


FDM


Accessories
»» Open door alarm.
»» Temperature recorder weekly chart.
»» Back-up system CO2 and LN2.
»» Ramp CO2 cylinder two-seater with automatic feeding exchanger.
»» Racks steel for cryoboxes.
»» Steel racks with drawers (for vertical models).
»» Steel sliding drawers various heights (for vertical models).
»» Additional shelves (for vertical models).
»» Vertical models from 390, 500 and 650 liters can be equipped with two doors instead of the door of service. The
‘use split of the interior, taking advantage of the physical characteristic of the cold air that tends to “fall” towards
the low, to allow the temperature of the lower sector to remain stable even in case of frequent openings Top
door. The operator then has the possibility of a diverse storage of samples allocating to the upper sector samples
most used and the lower one of the samples that use less frequent remain stable in ideal storage conditions.
»» Voltage stabilizer incorporated.
»» Audible and visual alarm system independent of the control system.
»» Refrigerant system remotely mounted outside the laboratory.
»» Additional refrigerant system with automatic activation in the event of failure of the primary.
»» Internal ventilation system for a greater distribution of the cold inside the refrigerated chamber.
»» Integrated customizable opening for access management and the traceability of authorized openings with reco-
gnition of smart cards and microprocessor software.
»» UPS system.
»» Validation IQ (Installation Qualification) and OQ (Operational Qualification).


FDM


Upright models
Model 86NV23 86NV39 86NV50 86NV65
Temperature range (room +32°C) -86°C -86°C -86°C -86°C
Capacity liters 230 400 500 650
External dimensions WxDxH cm 84 x 75 x 142 84 x 75 x 197 84 x 88 x 197 98 x 90 x 197
Internal dimensions WxDxH cm 61 x 50 x 76 61 x 50 x 131 60 x 63 x 131 74 x 67 x 131
Doors 1 1 1 1
Inner doors 2 4 4 4
2 of which 4 of which 4 of which 4 of which
Internal shelves adjustable 1 adjustable 3 adjustable 3 adjustable 3
Total capacity of steel racks 8 16 16 20
Total capacity of 5.1 cm H cryoboxes 144 240 320 400
Total capacity of 7.7 H cryoboxescm 96 144 192 240
Installed power Hp 0,75 x 2 1,7 x 2 1,7 x 2 1,7 x 2
Power consumption kW / h 0,8 1,55 1,55 1,55
Weight kg 200 280 320 390

Chest models
Model 86NR23 86NR39 86NR50
Temperature range (room +32°C) -86°C -86°C -86°C
Capacity liters 230 400 500
External dimensions WxDxH cm 100 x 84 x 109 155 x 84 x 109 189 x 84 x 91
Internal dimensions WxDxH cm 76 x 60 x 50 131 x 61 x 50 131 x 60 x 63
Doors 1 1 1
Inner doors 2 3 4
Total capacity of steel racks 20 36 36
Total capacity of 5.1 cm H cryoboxes 160 288 360
Total capacity of 7.7 H cryoboxescm 100 180 252
Installed power Hp 0,75 x 2 1,7 x 2 1,7 x 2
Power consumption kW / h 0,8 1,55 1,55
Weight kg 200 280 320


FDM

Deep Freezers -45°C Med

Temperature Range
»» Adjustable inner temperature from -20 ° C to -45 ° C.
»» Guaranteed operating temperature of -45 ° C at +32 ° C ambient temperature.
Structure
blue colors.
Thermal insulation
Inner chamber


FDM


Service door

Refrigerant system
models.
»» The static type evaporator is composed of a coil in copper which provides a very efficient thermal exchange, re-
duction of frost formation, greater internal volume available, low noise level, low energy consumption and more
compact overall dimensions.
»» Manual type of defrost system

Control instruments


FDM


Alerts and alarms
»» Visual and acoustic hot condenser alarm warns the operator if the condensing tem-
perature rises above the maximum value set, this may be caused by dust filter clog-
ged with deposits and therefore it becomes necessary an operation of filter cleaning.
The alarm system is equipped with a button to mute the sound.

Power supply

Noisiness
meters.

Certifications and Compliance
»» EEC Directive 2006/42/EC “Machinery”;
»» EEC Directive 2006/95/EC “Low Voltage”;
»» EEC Directive 2004/108/EC “Electromagnetic compatibility”;
»» CEI 66/5 “Safety requirements for electrical equipment for laboratory use”;
»» The gases used are not flammable and are not considered harmful to the environment according to the Montreal Pro-
tocol 1987 and subsequent amendments to London 1990 and Copenhagen 1992, then compliance with the law n °
549/93 (protection of the environment from contamination by chlorinated and fluorinated gases CFC);
»» The quality and safety of our equipment is guaranteed by the system design and production
»» UNI EN ISO 9001 and the CE mark.


FDM


Accessories
»» UPS system.


FDM


Upright models
Model 45NV23 45NV39 45NV50 45NV65
Doors 1 1 1 1
Inner doors 2 4 4 4
Installed power Hp 0,75 1,7 1,7 1,7
Power consumption kW / h 0,6 1 1 1
Weight kg 180 240 280 340

Chest models
Model 45NR23 45NR39 45NR50
Doors 1 1 1
Inner doors 2 3 4
Installed power Hp 0,75 1,7 1,7
Power consumption kW / h 0,6 1 1
Weight kg 180 240 280


FDM

Biomedical Med
Ultra Freezers -86°C

Temperature Range
»» Adjustable inner temperature from -40°C to -86°C.
»» Guaranteed operating temperature of -86°C at +32°C ambient temperature.
Structure
blue colors.
Thermal insulation
Inner chamber


FDM

Biomedical Med

Service door

Refrigerant system
models.
»» The static type evaporator is composed of a coil in copper which provides a very efficient thermal exchange,
reduction of frost formation, greater internal volume available, low noise level, low energy consumption and
more compact overall dimensions.
»» Manual type of defrost system.

Control instruments


FDM

Biomedical Med

Alerts & Alarms
»» Visual and acoustic hot condenser alarm warns the operator if the condensing
temperature rises above the maximum value set, this may be caused by dust
filter clogged with deposits and therefore it becomes necessary an operation of filter
cleaning. The alarm system is equipped with a button to mute the sound.

Power supply

Noise level
meters.

Quality Certifications & Compliances
»» Compliance with the Annex V (Module D1) Council Directive 93/42/EEC on Medical
Devices Class IIa.
»» The refrigerants used are non-flammable and are not considered harmful for the
environment according to the 1987 Montreal Protocol and subsequent amendments
of London 1990 and Copenhagen 1992.
»» The quality and safety of our equipments are guaranteed by design and production
systems certified UNI EN ISO 9001, ISO 13485 and CE Marking for Medical Devices.
»» Opened door alarm.
»» Weekly chart temperature recorder.
»» CO2 or LN2 Backup systems.


FDM

Biomedical Med
Accessories
»» Ramp with two seats of CO2 cylinders with automatic feeding exchanger.
»» Stainless steel racks for cryoboxes.
»» Stainless steel containers with drawers (for upright models only).
»» Stainless steel sliding drawers of different heights (for upright models only).
»» Additional shelves (for upright models).
»» The 390, 500 and 650 liters upright models can be equipped with two doors in place of the main door. Taking
advantage of the physical characteristic of the cold air that tends to “fall” down, the split use of the inner space allows the
temperature of the lower sector to remain stable even in case of frequent openings of the upper door. The operator
then has the possibility of a diversified storage of samples allocating the samples that are used most often in the higher
sector and in the lower one the samples used less frequently which remain firmly in ideal storage conditions.
»» Incorporated voltage stabilizer.
»» Visual and acoustic alarm system independent of the control system.
»» Remote cooling system to be mounted outside of the laboratory.
»» Additional cooling system with automatic activation in the event of failure the main one.
»» Internal air ventilation system for a greater distribution of the cold inside the refrigerated chamber.
»» Integrated customizable opening system for monitoring and recording of authorized access and traceability of openings
with recognition of smart cards and microprocessor management software.
»» Power supply UPS backup system.
»» I.Q. (Installation Qualification) and O.Q. (Operational Qualification) Validations.


FDM

Biomedical Med
Upright models
Model 86ES23 86ES39 86ES50 86ES65
Doors 1 1 1 1
Inner doors 2 4 4 4
Installed power Hp 0,75 x 2 1,7 x 2 1,7 x 2 1,7 x 2
Power consumption kW / h 0,8 1,55 1,55 1,55
Weight kg 200 280 320 390

Chest models
Model 86ES23R 86ES39R 86ES50R
Doors 1 1 1
Inner doors 2 3 4
Installed power Hp 0,75 x 2 1,7 x 2 1,7 x 2
Power consumption kW / h 0,8 1,55 1,55
Weight kg 200 280 320


FDM

Biomedical Med
Deep Freezers -45°C

Temperature Range
»» Guaranteed operating temperature of -45 ° C at +32 ° C ambient temperature.
Structure
blue colors.
Thermal insulation
Inner chamber


FDM

Biomedical Med
Service door

Refrigerant system
models.
»» The static type evaporator is composed of a coil in copper which provides a very efficient thermal exchange, re-
duction of frost formation, greater internal volume available, low noise level, low energy consumption and more
compact overall dimensions.
»» Manual type of defrost system

Control instruments


FDM

Biomedical Med

Alerts and alarms
»» Visual and acoustic hot condenser alarm warns the operator if the condensing tem-
perature rises above the maximum value set, this may be caused by dust filter clog-
ged with deposits and therefore it becomes necessary an operation of filter cleaning.
The alarm system is equipped with a button to mute the sound.

Power supply

Noisiness
meters.

»» EEC 93/42/EEC (medical devices) Class IIa;
»» The gases used are not flammable and are not considered harmful to the environment according to the Montreal
Protocol 1987 as amended in London 1990, Copenhagen 1992, then in accordance with Law No. 549/93 (protection
environment from contamination by gases chlorinated and fluorinated CFC);
»» The quality and safety of our equipment is guaranteed by the system design and production certification market UNI
EN ISO 9001:2008 and UNI EN ISO 13485:2004 and CE mark.


FDM

Biomedical Med

Accessories
»» UPS system.


FDM

Biomedical Med
Upright models
Model 45ES23 45ES39 45ES50 45ES65
Doors 1 1 1 1
Inner doors 2 4 4 4
Installed power Hp 0,75 1,7 1,7 1,7
Power consumption kW / h 0,6 1 1 1
Weight kg 180 240 280 340

Chest models
Model 45ES23R 45ES39R 45ES50R
Doors 1 1 1
Inner doors 2 3 4
Installed power Hp 0,75 1,7 1,7
Power consumption kW / h 0,6 1 1
Weight kg 180 240 280


FDM

Ultra and Deep Freezers Med
Accessories
Chart temperature recorder
»» BA0188 - Circular chart temperature recorder with temperature independent, temperature range -100 ° / +40 ° C, Quartz
clockwork powered by battery 1.5 V DC, disk recording plotted diameter 11 cm, lock with key. Including 52 discs plotted and 2 nibs.

Back-up systems CO2
»» BK201 - Liquid CO2 back-up system. In the need of intervenes autonomously, injecting small amounts of liquid carbon dioxide
that evaporates inside the chamber maintain the temperature below that of emergency (normally -65 ° C) for the time necessary
to the repair. With a normal 90-liter tank is guaranteed the temperature of -65 ° C for at least 36 hours. This system is equipped with
stainless steel pipe at high pressure for the connected to the cylinder, the test button, the microprocessor module and temperature
sensor independent and Auto charging 12V buffer battery that allows the functioning of the system even in case of power failure.
»» BK101 - Liquid CO2 back-up system. Features and operation completely similar to the previous article BK201 with the only dif-
ference that it is not equipped with buffer battery Auto charging 12V.

Cylinder manifold
»» RB201 - The function of the manifolds is connecting multiple cylinders to each other, allowing them to be used as a supply
source for a medical gas distribution system. Allows the simultaneous connection of two cylinders CO2 systems and emergency
BK201 BK101. Ready to fit to the wall, equipped with a rack at two places for fixing in a vertical position of CO2 cylinders with suc-
tion, with pipes made of copper for high pressure CO2 for connecting the cylinders to the ramp and safety valves of each cylinder
connected.

Exchanger automatic CO2 supply
»» SB201 - Connected to the ramp RB201 allows the automatic exchange between the cylinders for the power supply of the
emergency system. When the first tank empties the device automatically switches to the reserve cylinder and warns the operator
with a visual and audio alarm. The device is powered by a buffer battery Auto charging 12V for operation the system also in case of
power failure. The alarm system is also equipped with clean contact for any remote connection.

Back-up systems LN2
»» BK202 - System emergency back-up liquid LN2. In emergencies intervenes automatically, injecting small quantities of liquid
nitrogen from the plant centralized, which evaporates inside the chamber to maintain the temperature below that of emergency
(normally -65 ° C) for the time necessary to the repair. This system is equipped with high pressure stainless steel pipe for connection
to the centralized system, the test button, the microprocessor module and temperature sensor independent and Auto charging
12V buffer battery that allows the functioning the system also in case of power failure.
»» BK102 - Emergency system operating at LN2 liquid. Features and operation completely similar to the previous article BK202
with the only difference that it is not equipped with buffer battery Auto charging 12V.

Voltage regulator
»» ST100 - Voltage regulator incorporated, can deliver up to 18 volts to over-boost. Lifetime guarantee to the compressors, which
adversely affected the power surges.


FDM

Accessories
Temperature controller auxiliary
»» CT100 - Temperature controller with auxiliary sensor independent. With this accessory the Freezer is equipped with a double
system of temperature control: one rated and an emergency, both equipped with own independent temperature sensor. In case of
failure of the primary system control automatically switches to the secondary, allowing the regular operation of the freezer.

Cryoboxes
»» B2-081 - Box for 0.5 to 2 ml test tubes in waterproof cardboard with internal dividers to 81 places and external dimensions of
13.3 x 13.3 x 5.1 cm H (height 2 inches).
»» B2-100 - Box for 0.5 to 2 ml test tubes in waterproof cardboard with internal dividers with 100 seats and exterior dimensions of
»» B3-081 - Box for 0.5 to 2 ml test tubes in waterproof cardboard with internal dividers to 81 places and external dimensions of
»» B3-100 - Box for 0.5 to 2 ml test tubes in waterproof cardboard with internal dividers with 100 seats and exterior dimensions of


FDM

Accessories
Racks for Cryoboxes
Upright freezer racks
Upright freezer 86NV23 and 45NV23 230 liters
»» The Ultra Freezer features 2 shelves, each one can contain up to 4 racks, maximum receive 8 racks.
»» V2-18 - Stainless steel container of cm 14 x 42 x 34 H, can contain up to 18 cryoboxes cm 13.3 x 13.3 x 5.1 H.
»» V2-18C - Stainless steel container of cm 14 x 42 x 34 H, complete with 18 cryoboxes cm 13.3 x 13.3 x 5.1 H.

»» The Ultra-Freezer has 4 shelves, each one can contain up to 4 racks, 16 racks maximum reception.

Upright Freezer 86NV50 and 45NV50 500 liters
»» The Ultra-Freezer has 4 shelves, each shelf can hold up to 4 racks, 16 racks maximum reception.

»» The Ultra-Freezer has 4 shelves, each shelf can hold up to 5 racks, 20 racks maximum reception.
»» »» V2-20 - Stainless steel container of cm 14 x 56 x 28 H, can contain up to 20 cryoboxes cm 13.3 x 13.3 x 5.1 H.
»» »» V3-12 - Stainless steel container of cm 14 x 56 x 28 H, can contain up to 12 cryoboxes cm 13.3 x 13.3 x 7.7 H.
»» »» V2-20C - Stainless steel container of cm 14 x 56 x 28 H, complete with 20 cryoboxes cm 13.3 x 13.3 x 5.1 H.
»» »» V3-12C - Stainless steel container of cm 14 x 56 x 28 H, complete with 12 cryoboxes cm 13.3 x 13.3 x 7.7 H.

Chest freezer racks
Chest Freezer 86NV23 and 45NV23 230 liters
»» The Ultra-Freezer can contain a maximum of 20 racks.
»» R2-08 - Stainless steel container of cm 14 x 14 x 45 H, can contain up to 8 cryoboxes cm 13.3 x 13.3 x 5.1 H.
»» R2-08C - Stainless steel container of cm 14 x 14 x 45 H, complete with 8 cryoboxes cm 13.3 x 13.3 x 5.1 H.


FDM

Accessories
Chest Freezer 86NV39 and 45NV39 390 liters
»» The Ultra Freezer can contain a maximum of 36 racks.

Chest Freezer 86NR50 and 45NR50 500 liters

Drawers
»» VS2070 - Stainless steel drawer slides on telescopic rails. Size cm 56 x 42 x 7 H. Distance between bottom-drawer and
bottom-drawer top 8 cm. The Ultra Freezer can contain a maximum of 9 drawers.
»» VS2090 - Stainless steel drawer slides on telescopic rails. Size cm 56 x 42 x 9 H. Distance between bottom-drawer and bottom-
top drawer 10.8 cm. The Ultra Freezer can contain a maximum of 6 drawers of this type addition to a drawer with a height of 7 cm
(VS2070). Total capacity of 7 drawers.
bottom-top drawer of 16 cm. The Ultra freezer can contain a maximum of 4 drawers of this type addition to a drawer with a height
of 7 cm (VS2070). Total capacity of 5 drawers.

bottom-drawer top 8 cm. The Ultra freezer can contain up to 16 trays of this type. Total capacity 16 trays.
bottom-top drawer 10.8 cm. The Ultra Freezer can contain up to 12 trays of this type. Total capacity 12 trays.
bottom-top drawer 16 cm. The Ultra Freezer can contain up to 8 trays of this type. Total capacity 8 drawers.


FDM

Accessories
bottom-drawer top 8 cm. The Ultra Freezer can contain up to 16 trays of this type. Total capacity 16 trays.
»» VS5090 - Stainless steel drawer slides on telescopic rails. Size cm 56 x 56 x 9 H. Distance between bottom-drawer and bottom-top
drawer 10.8 cm. The Ultra Freezer can contain up to 12 trays of this type. Total capacity 12 trays.
»» VS5130 - Stainless steel drawer slides on telescopic rails. Size cm 56 x 56 x 13 H. Distance between bottom-drawer and bottom-top
drawer 16 cm. The Ultra Freezer can contain up to 8 trays of this type. Total capacity 8 drawers.

»» VS6070 - Stainless steel drawer slides on telescopic rails. Size: 70 x 56 x 7 H. Distance between bottom-drawer and bottom-drawer
top 8 cm. The Ultra Freezer can contain up to 16 trays of this type. Total capacity 16 trays.
»» VS6090 - Stainless steel drawer slides on telescopic rails. Size: 70 x 56 x 9 H. Distance between bottom-drawer and bottom-top
drawer 10.8 cm. The Ultra Freezer can contain up to 12 trays of this type. Total capacity 12 trays.
»» VS6130 - Stainless steel drawer slides on telescopic rails. Size cm 70 x 56 x 13 H. Distance between bottom-drawer and bottom-
top drawer 16 cm. The Ultra Freezer can contain up to 8 trays of this type. Total capacity 8 drawers.

»» Internal separators on request.


FDM

Biomedical Blast Freezer
Emo
Plasma Freezer 86ES23
Temperature range
»» Guaranteed operating temperature of -86 ° C to +32 ° C ambient temperature.

Structure
»» External coating and base steel phosphated strong thickness treated with
epoxy powder paints in white and blue.
»» Installation of high-strength casters for easy movement.
Thermal insulation
»» Polyurethane foam insulation with high insulation, CFC and HCFC, injected
high density with layer of 12 cm for the side walls and 14 cm to the back wall.

Inner chamber
»» Covering of the inner chamber of stainless steel 18/8 AISI 304.
»» Intermediate shelves in stainless steel grid 18/8 AISI 304 telescopic runners.
»» Inner doors with independent closing.

Service port
»» The self-balancing hinges are adjustable to assure proper alignment of the
door with the main body and then a correct closure and a perfect seal of the
gasket with reduction of the formation of frost and consequent operations of
defrosting.

Refrigerant system
»» Completely sealed refrigerating system with two compressors operating with cascade circuit. The freezer is
equipped with hermetic compressors from 1.7 Hp.
»» Ecological refrigerant gas HFC Free, CFC and HCFC.
»» The compressors are equipped with an automatic protection system in case of overpressure that protects the
compressors operating under extreme conditions of operation.
»» The evaporator of ventilated type consists of a copper coil, provides a heat exchange super-efficient,
dehumidification and frost formation reduced, high air throw, low noise, low power consumption and compact
overall dimensions.
»» Condensation ventilated type with dimensions increased to ensure optimum performance freeze even at high am-
bient temperatures. The air-cooled condenser is equipped with fan motors with axial movement of ball bearings
to ensure a low noise level and greater durability.
»» A dust filter composed of washable polyester foam protects the capacitor from deposits of dust, can be easily
clean with washing in water.
»» System manual defrost.

F.lli Della Marca S.r.l. Viale Arcangelo Ghisleri 40-42, 00176 - Roma, Italy tel: 06-298042 - fax: 06-273514

FDM

Emo
System freezing
»» System for rapid freezing of plasma (shock freezing), setting the time of freezing, with ease of programming and
ability to keep in memory the last program used. For each cycle can be frozen quickly, within the time allowed
by applicable law, up to 44 bags of 200 ml, 22 bags of 400ml, 450ml 20 bags, 14 bags of 650ml or 1000ml 9
pouches. The plasma bags are brought from ambient temperature to that of -30 ° C at the core of the product in
48 minutes, is also possible to continue the freezing of the bags up to a temperature of -70 ° C.
»» Warning light of frost and defrost, and warning end frost.

Control equipment
»» Internal temperature is controlled by electronic controllers of latest generation PLC.
»» Temperature setting simple buttons on the front panel.
»» All settings can be inhibited to strangers using password access to the controls.
»» Electronic module with IP65.
»» Arrangement for monitoring and / or recording of data with serial interface RS485.
»» The whole control system is equipped with a buffer battery 12V Auto- charging. It allows the operation of the
digital display of temperature, even in case of lack electric current.
Signals and alarms
»» Visual and acoustic temperature alarm alerts the operator if the internal temperature falls
below the preset limit or else if it rises above the expected one. The device is equipped
with a test button, a mute button and a free contact for remote connection.
»» Visual and acoustic hot condenser alarm warns the operator if the condensing temperature
rises above the maximum value set, this may be caused by dust filter clogged with deposits
and therefore it becomes necessary an operation of filter cleaning.
»» The alarm system is equipped with a button to mute the sound.

Power Supply
»» Power 220/230V 50Hz single-phase outlet interlocked 16 Ah
Noisiness
»» Noise level less than 58 dB at a distance of one meter, less than 53 dB at three meters.

»» 93/42/EEC (medical devices) Class IIa;
»» The gases used are not inflammable and are not considered harmful to the environment according to the 1987
Montreal Protocol and its amendments of London 1990 and Copenhagen 1992, then in accordance with Law No.
549/93 (protection of the environment from contamination by gas chlorinated and fluorinated CFC);
»» The quality and safety of our equipment is guaranteed by the system design and production certified UNI EN ISO
9001:2008 and UNI EN ISO 13485:2004 and CE mark.


FDM

Emo

Data sheet
• Temperature range (room +32°C): -86°C
• Refrigeration: ventilated
• Liters capacity: 230
• External dimensions WxDxH cm: 84 x 75 x 142
• Internal dimensions WxDxH cm: 60 x 50 x 76
• Doors: 1
• Inner Doors: 2
• Internal shelves: 4 telescopic runners
• Freezing rate: less then 50 minutes
• Freezing capacity: up to 44 bags 200 ml,
22 bags 400ml, 20 bags 450ml,
14 bags 650ml, 9 bags 1000ml.
• Power Hp: 1,7 x 2
• Power consumption Kw/h: 1,55
• Weight Kg: 200


FDM

Emo

Accessories

»» Electronic system with touch-screen operator panel, for the acquisition of information using
barcode reader on the plasma bag to be inserted in the freezer.

»» Recording traced the relative temperatures, with the ability to transfer data to your
computer, in text format, using ethernet or memory card.



»» Integrated customizable opening for access management and the traceability of authorized
openings with recognition of smart cards and microprocessor software.

»» UPS System.

»» Validation I.Q. (Installation Qualification) and O.Q. (Operational Qualification).


FDM

Blood Bank Refrigerators series E Emo
Temperature range of 2 ° C / 10 ° C. Cabinet and door white painted
sheet or stainless steel AISI 304. Polyurethane insulation foam with
high density, CFC and HCFC. Rounded corners and bottom of tank to
prevent liquids. Glass door reversible triple tempered glass with hollow
vacuum. Internal drawers with stainless steel AISI 304 with telescopic
rollover in three storage spaces. Interior lighting with LED tube, positio-
ned on the side of the storage cell. Electronic temperature controller with
microprocessor to continuously monitor and digital display brightness-
so the internal temperature and the set temperature. Audio-visual alarm
minimum and maximum temperature with contact remote connection. Door
open alarm, power failure, low battery and dirty condenser. All alarms
are equipped with acoustic acknowledgment. RS485 PC connection port.
Control panel equipped with a buffer battery which allows keeping active
the temperature display and the alarm functions of temperature even
in case of power failure. All temperature controls and alarms can be
inhibited to strangers by password access to the controls. Temperature
recorder weekly chart. Ventilated refrigeration. Static condensation.
Manual defrost or automatic electronic. Steel adjustable feet or rollers
made of plastic material. Noise level less than 50 dB. Power supply 220V
1-50Hz.

Accessories
»» Partitions for drawers
»» Safety lock with key
»» Cable port with rubber plug
»» Function data logger with USB port
Model »» Front top for drawers
E400
model capacity external dimension insulation doors drawers capacity bags consumption weight
liters WxDxH cm mm 450 ml kW/h kg

E140 140 53x64x94 50 1 3 81 280 80

E300 300 60x65x164 50 1 4 96 430 95

E400 400 60x65x202 50 1 6 144 590 120

E500 500 60x70x192 50 1 6 180 820 130

E600 600 75x70x210 75 1 7 280 540 185

E700 700 75x82x210 75 1 7 336 540 190

E1000 1000 120x70x192 75 2 12 360 1220 240

E1200 1200 150x70x210 75 2 14 560 785 270

E1500 1500 144x80x210 75 2 14 672 785 230

E2300 2300 225x82x210 75 3 21 1008 1380 430


FDM

Climate Cabinet 0°/+80°C series CS Clima
Temperature range 0°/+80°C. Setting and readability
temperature in increments of 0.1°C. Temperature Stability
± 0.1°C. Average speed up / down temperature 0.5°C / min.
Built entirely in white plastic coated galvanized steel or stainless
steel AISI 304. Polyurethane insulation CFC and HCFC. Rever-
sible doors with self-closing hinges with retainer beyond 90°
and replaceable magnetic gaskets plug. Inside with rounded cor-
ners. Inner Door lexan. Grids removable and height adjustable
stain-less plastic. Adjustable steel feet. The cabinet is equip-
ped with a microprocessor controller with a single program in
20 steps. Electronic temperature controller with microprocessor
to continuously monitor and display digital bright indoor tem-
perature and the set temperature. Audio-visual alarm minimum
and maximum temperature with acoustic acknowledgment and
dry contact remote connection. The temperature settings and
alarm can be inhibited to strangers by password access to the
controls. Control relative humidity between 10% and 98% ± 2%
dew point +2°C. Humidification with adjustable generator of
low-pressure steam can operate with demineralized water,
sweetened or aqueduct with hardness from 0 to 400 ppm of
CaCO3. Power supply with mains water with pressure between 1
and 10 bar. Dehumidification with direct expansion evaporator in
Freon. Heatingelements with low inertia. Ventilation. Safety device
class 3.1 (DIN 12880): protects the cabinet, its contents and the
surrounding environment with the automatic intervention of two
additional temperature controllers that, in the event of failure of
the main thermoregulator, prevent the internal temperature to
exceed the limits to set minimum and maximum, the interven-
tion of additional temperature control is signaled by a red light.
Safety device with manual reset class 1 (DIN 12880): comple-
tely off the heating when the temperature exceeds the preset
maximum value cannot be modified. Noise level less than 55 dB.
C440S
Power supply 220-230V 1-50Hz.

Model
model external dimension capacity internal dimension doors drawers absorption
WxDxH cm litres WxDxH cm W
C130S 53x64x94 130 1 2 1300

C270S 60x65x164 270 50x48x125 1 2 1300

C370S 60x60x192 370 50x48x125 1 3 1500

C440S 60x70x192 440 50x58x125 1 3 1500

C600S 75x70x210 600 60x57x130 1 3 1600

C700S 75x82x210 700 60x67x130 1 3 1800

C900S 120x70x192 900 110x58x125 2 3 2000

C1200S 150x70x210 1200 132x57x130 2 6 2000

C1500S 150x82x210 1500 132x67x130 2 6 2000


FDM

Climate Cabinet 0°/+80°C series CS Clima
Accessories
»» Lock and key.
»» Temperature and humidity recorder continuous trace.
»» Program of continuous monitoring in a network with local PC for management of alarm devices,
normalized recording and printing of graphics of the detected values of temperature and humidity.

»» Glass doors (*)
»» Fluorescent horizontal shelves and vertical side (*)
»» Dimming with fractional power of the lamps.
»» Fluorescent lighting with dimmable ballasts.
»» Lighting luorescente vertical outer side wall with glass. Control photo-period cycle timer with 24 hours.
»» Control day / night temperature.
»» Humidity control day / night.
»» Programmers with 10 programs and 50 broken, 25 or 50 programs and 100 programs and 200 broken
broken to install in place of the serial programmer (1 program and 20 steps).
»» Hole diameter mm 35/50 and a rubber stopper.
»» Power supply 220-230V(Different power on request).

(*) Excluding models C370 - C440 - C900.

Powerful regulator of single-loop or dual-loop
Dual-loop control - ideal for processes with two variables
interactive.

Accurate measurement of PV combined with control with high per-
formance resulting in high product quality
Modular units and flexible - up to 6 I / O slots with 16 different
modules.

Graphical editor to create advanced and flexible solutions in a sim-
ple way.

Easy integration systems - Modbus RTU, Modbus TCP, Profibus and
DeviceNet network.

Simple and intuitive operation with customizable display
Setpoint programming with dual channel capability - up to 50 pro-
grams based on time.


FDM

Climate Cabinet -20°/+80°C series CS Clima
Temperature range -20°/+80°C. Setting and readability
C440B

Model
C270B 60x65x164 270 50x48x125 1 2 1300

C370B 60x60x192 370 50x48x125 1 3 1500

C440B 60x70x192 440 50x58x125 1 3 1500

C600B 75x70x210 600 60x57x130 1 3 1600

C700B 75x82x210 700 60x67x130 1 3 1800

C900B 120x70x192 900 110x58x125 2 3 2000

C1200B 150x70x210 1200 132x57x130 2 6 2000

C1500B 150x82x210 1500 132x67x130 2 6 2000


FDM

Climate Cabinet -20°/+80°C series CB Clima
Accessories
»» Lock and key.



interactive.

modules.

ple way.

DeviceNet network.



FDM

Climate Cabinet -30°/+80°C series CN Clima
Temperature range -30°/+80°C. Setting and readability
C440N

Model
C270N 60x65x164 270 50x48x125 1 2 1300

C370N 60x60x192 370 50x48x125 1 3 1500

C440N 60x70x192 440 50x58x125 1 3 1500

C600N 75x70x210 600 60x57x130 1 3 1600

C700N 75x82x210 700 60x67x130 1 3 1800

C900N 120x70x192 900 110x58x125 2 3 2000

C1200N 150x70x210 1200 132x57x130 2 6 2000

C1500N 150x82x210 1500 132x67x130 2 6 2000


FDM

Climate Cabinet -30°/+80°C series CB Clima
Accessories
»» Lock and key.



interactive.

modules.

ple way.

DeviceNet network.



FDM

Climate Cabinet 0°/+80°C series TS Clima

Temperature range 0°/+80°C. Setting and readability
± 0.1°C. Built entirely in white plastic coated galvanized steel or
stainless steel AISI 304. CFC-free polyurethane insulation with a
thickness of 75 mm. Self-closing doors with magnetic gaskets. Inner
Door lexan. Grids removable and adjustable in height. Electronic tem-
perature controller with microprocessor to continuously monitor and
digital display light of the internal temperature and the set temperature.
Audio-visual alarm minimum and maximum temperature with acoustic
acknowledgment and dry contact remote connection. The temperature
settings and alarm can be inhibited to strangers by password access
to the controls. Heating elements with low inertia. Safety device class
3.1 (DIN 12880) protects the cabinet, its contents and the surrounding
environment with the automatic intervention of two additional tempera-
ture controllers that, in the event of failure of the main thermoregulator,
prevent the internal temperature to exceed the limits of set minimum
and maximum, the intervention of additional temperature control is
signaled by a red light. Safety device class 1 (DIN 12880) completely
off the heating when the temperature exceeds the preset maximum
value can not be modified. Inner ventilation. Noise level is non-payment
of less than 55 dB. Adjustable steel feet. Power supply 220V 1-50Hz.

Model T440S
T130S 53x64x94 130 1 2 1300

T270S 60x65x164 270 50x48x125 1 2 1300

T370S 60x60x192 370 50x48x125 1 3 1500

T440S 60x70x192 440 50x58x125 1 3 1500

T600S 75x70x210 600 60x57x130 1 3 1600

T700S 75x82x210 700 60x67x130 1 3 1800

T900S 120x70x192 900 110x58x125 2 3 2000

T1200S 150x70x210 1200 132x57x130 2 6 2000

T1500S 150x82x210 1500 132x67x130 2 6 2000


F.lli Della Marca

Recommended

Recommended

More Related Content

What's hot

What's hot (15)

Similar to F.lli Della Marca

Similar to F.lli Della Marca (20)

Recently uploaded

Recently uploaded (20)

F.lli Della Marca