This document is a repair manual for Jaguar 900-830 Profistar and Speedstar harvesters. It contains sections covering the operator's platform, cab, heating, air conditioning, driver's seat, operating elements, steering, brakes, and electrics systems. The manual provides instructions for removing, dismantling, assembling, and fitting various components of these systems. Safety information is also provided at the beginning, including important notes on general safety rules, pressure accumulators, and maintenance.
This document provides operation instructions for multi-turn actuators models SA 07.1 - SA 16.1 and SAR 07.1 - SAR 16.1 with AUMA MATIC controls. It describes the scope, technical specifications, safety instructions, transport and storage, mounting, manual operation, electrical connection, setting of limit switches, torque switching, position indicators, and maintenance procedures. The document contains 21 sections covering all aspects of installation, setup and maintenance of the actuators.
The document provides safety instructions and assembly instructions for multi-turn actuators and actuator controls. It discusses transport, storage, identification, assembly, electrical connection, operation, signals, commissioning, servicing, technical data, spare parts, and certificates. Safety is the top priority, with warnings about hazards, proper qualification of personnel, commissioning, and operation. The document contains detailed steps for assembly, electrical connection, setting limits and positions, testing, and commissioning controls.
Volkswagen TDI 3.0L 265-6 DIESEL MARINE ENGINE Service Repair Manualhjdkmsmeme
This workshop manual provides technical information and instructions for servicing a VW Marine Boat Engine BKS 6-Cylinder Diesel Engine. It covers topics such as safety precautions, self-diagnosis procedures, fault memory interrogation, control element diagnosis, measurement blocks, removing and installing the engine, overhaul procedures for various engine systems, and removing and installing crankshafts, pistons and connecting rods. The manual is intended as a guide for technicians servicing this engine model.
Electrical power supply and distributionSouvik Dutta
This document is a technical manual that provides guidance on electrical power supply and distribution systems for the Army and Air Force. It covers topics such as voltage selection, main electric supply stations/substations, aerial and underground distribution lines. The manual establishes standards and procedures for designing, evaluating, and selecting electrical power systems to ensure reliable and efficient power delivery to military installations.
This document provides service information for a lift truck, including specifications, maintenance schedules, part replacements, and adjustments. It contains electrical specifications, speeds, hydraulic details, tire and wheel info, fluid types, torque values, troubleshooting guides, and instructions for motor repair. Maintenance tasks are outlined on a schedule with hours or time intervals. Procedures are provided for replacing load wheels, drive tires, and motor service. Adjustments are described for brakes, switches, steering, lift chains, speed limiting, and potentiometers.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjsekdhjenmdn
This document provides instructions for removing and installing steering clutches on a D5C III track-type tractor. Key steps include draining oil from the steering clutch compartment, removing components like the control valve and brake housing, and disassembling the clutches by removing parts like the cylinder, piston, springs, and drums. Reassembly involves installing these same components in reverse order, applying sealants and lubricants, and adjusting settings like bolt torques and linkage lengths.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjsekdhjenmdn
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, and idler gear. The idler shaft is then pulled from the cylinder block. Installation is the reverse of removal, ensuring proper alignment of timing marks on the gears.
This document provides operation instructions for multi-turn actuators models SA 07.1 - SA 16.1 and SAR 07.1 - SAR 16.1 with AUMA MATIC controls. It describes the scope, technical specifications, safety instructions, transport and storage, mounting, manual operation, electrical connection, setting of limit switches, torque switching, position indicators, and maintenance procedures. The document contains 21 sections covering all aspects of installation, setup and maintenance of the actuators.
The document provides safety instructions and assembly instructions for multi-turn actuators and actuator controls. It discusses transport, storage, identification, assembly, electrical connection, operation, signals, commissioning, servicing, technical data, spare parts, and certificates. Safety is the top priority, with warnings about hazards, proper qualification of personnel, commissioning, and operation. The document contains detailed steps for assembly, electrical connection, setting limits and positions, testing, and commissioning controls.
Volkswagen TDI 3.0L 265-6 DIESEL MARINE ENGINE Service Repair Manualhjdkmsmeme
This workshop manual provides technical information and instructions for servicing a VW Marine Boat Engine BKS 6-Cylinder Diesel Engine. It covers topics such as safety precautions, self-diagnosis procedures, fault memory interrogation, control element diagnosis, measurement blocks, removing and installing the engine, overhaul procedures for various engine systems, and removing and installing crankshafts, pistons and connecting rods. The manual is intended as a guide for technicians servicing this engine model.
Electrical power supply and distributionSouvik Dutta
This document is a technical manual that provides guidance on electrical power supply and distribution systems for the Army and Air Force. It covers topics such as voltage selection, main electric supply stations/substations, aerial and underground distribution lines. The manual establishes standards and procedures for designing, evaluating, and selecting electrical power systems to ensure reliable and efficient power delivery to military installations.
This document provides service information for a lift truck, including specifications, maintenance schedules, part replacements, and adjustments. It contains electrical specifications, speeds, hydraulic details, tire and wheel info, fluid types, torque values, troubleshooting guides, and instructions for motor repair. Maintenance tasks are outlined on a schedule with hours or time intervals. Procedures are provided for replacing load wheels, drive tires, and motor service. Adjustments are described for brakes, switches, steering, lift chains, speed limiting, and potentiometers.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjsekdhjenmdn
This document provides instructions for removing and installing steering clutches on a D5C III track-type tractor. Key steps include draining oil from the steering clutch compartment, removing components like the control valve and brake housing, and disassembling the clutches by removing parts like the cylinder, piston, springs, and drums. Reassembly involves installing these same components in reverse order, applying sealants and lubricants, and adjusting settings like bolt torques and linkage lengths.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 9dl) serv...fjsekdhjenmdn
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar 3046 engine. The removal procedure involves removing the front housing, idler gear bolt, thrust plate, and idler gear. The idler shaft is then pulled from the cylinder block. Installation is the reverse of removal, ensuring proper alignment of timing marks on the gears.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 6zl) serv...fjsekdhjenmdn
The document provides instructions for removing and installing the transmission oil pump and pump drive gear on a D5C III track-type tractor. Key steps include draining the transmission oil, removing the tube assembly, plate, and transmission oil pump. The pump drive gear is then removed from the transmission case. Reinstallation involves reversing these steps, ensuring proper placement of seals and connection of hoses.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 5hs) serv...fjsekdhjenmdn
This service repair manual provides instructions to remove and install final drives on D5C III track-type tractors. It outlines 33 steps to disassemble the final drive, including removing the final drive assembly, various gears, bearings, seals and other components. It then describes 35 steps to reassemble the front drive, including installing new seals, bearings, gears and other parts back into the final drive assembly. Safety procedures are provided to contain fluids and ensure proper cleaning, heating and installation of components.
Caterpillar cat 966 h wheel loader (prefix tal) service repair manual (tal000...fjsekdhjenmdn
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for fasteners.
Caterpillar cat 966 h wheel loader (prefix ryf) service repair manual (ryf000...fjsekdhjenmdn
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
Caterpillar cat 966 h wheel loader (prefix bj6) service repair manual (bj6000...fjsekdhjenmdn
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar C11 engine. The removal procedure involves using various tools to remove 12 different components in 11 steps. The installation procedure involves 14 steps of reinstalling components and includes notes about properly aligning bearings and applying threadlock. Tolerances and torque specifications are provided for correctly installing some components.
Caterpillar cat 962 k wheel loader (prefix x4t) service repair manual (x4t000...fjsekdhjenmdn
This document provides instructions for disassembling and assembling the piston pump of the steering system on a Caterpillar 962K wheel loader. The disassembly procedure outlines 28 steps to remove components like bolts, valves, spools, springs, and bearings. The assembly procedure describes 34 steps and cautions to install these components in reverse order and ensure proper spring tension, seals, and shaft clearance. Precautions are included to prevent injury from parts under spring force.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjsekdhjenmdn
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, and tightening bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts.
Caterpillar cat 962 k wheel loader (prefix fll) service repair manual (fll000...fjsekdhjenmdn
The document provides instructions for disassembling and assembling the piston pump of the steering system on a 962K wheel loader. It describes 28 steps to disassemble the pump by removing components like bolts, valves, spools, springs, and bearings. It then describes 31 steps for reassembling the pump by reversing the disassembly process and ensuring proper installation of O-rings, seals, plates, and tightened bolts. The overall document provides a detailed technical procedure for maintenance or repair of the steering system piston pump.
Caterpillar cat 320 l track type excavator (prefix 9kk) service repair manual...fjsekdhjenmdn
The document provides instructions for removing and installing the idler gear of an excavator engine. It begins by noting the required tools and importance of alignment marks. The removal procedure instructs to remove the idler gear bolt and washer, then remove the thrust plate from the idler gear shaft. Tooling is then used to pull the idler gear off the shaft. The installation procedure is not shown, but presumably involves reversing the removal steps.
Caterpillar cat 320 l track type excavator (prefix 7wk) service repair manual...fjsekdhjenmdn
This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including installing a crankshaft rear seal carrier, installing a crankshaft wear sleeve, and removing and installing a flywheel housing. The document lists required tools and provides step-by-step instructions with illustrations for each procedure.
Caterpillar cat 320 l track type excavator (prefix 1kl) service repair manual...fjsekdhjenmdn
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and valve seals on Caterpillar 3064 and 3066 engines. The procedures include using various specialty tools to compress springs, extract components, and properly seat new parts. Technicians are advised to keep components clean and lubricate parts during installation.
Caterpillar cat 320 track type excavator (prefix 9 kk) service repair manual ...fjsekdhjenmdn
The document provides instructions for removing and installing the idler gear of an excavator engine. It begins by noting the required tools and importance of alignment marks. The removal procedure instructs to remove the idler gear bolt and washer, then remove the thrust plate from the idler gear shaft. Tooling is then used to pull the idler gear off the shaft. The installation procedure is not shown, but presumably involves reversing the removal steps.
Caterpillar cat 320 track type excavator (prefix 7 wk) service repair manual ...fjsekdhjenmdn
This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including:
1) Installing the crankshaft rear seal and sleeve using a special tooling set.
2) Removing and installing the crankshaft rear seal carrier using gasket sealant and thread lock compound.
3) Removing and installing the flywheel housing using link brackets and gasket sealant.
Caterpillar cat 320 track type excavator (prefix 1 kl) service repair manual ...fjsekdhjenmdn
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and valve seals on Caterpillar 3064 and 3066 engines. The procedures include using various specialty tools to compress springs, extract components, and properly seat new parts. Technicians are advised to keep components clean and lubricate parts during installation.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...fjsekdhjenmdn
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix fr5) service rep...fjsekdhjenmdn
The document provides instructions for removing and installing various components of a 305.5E2 CR Mini Hydraulic Excavator FR5 engine, including the fuel manifold rail, fuel injection lines, electronic unit injector, turbocharger, exhaust gas recirculation valve, and more. The steps describe draining fluids, removing bolts, clamps and other hardware, and installing components in reverse order, noting proper torque specifications for reinstallation. Safety warnings are provided throughout regarding hazards such as high pressure fuel, sulfuric acid, and hot coolant.
Takeuchi tb108 compact excavator parts catalogue manual sn10810004~10812001fjsekdhjenmdn
This document provides an index and parts list for a TB108 excavator with serial numbers between 10810004-10812001. The index lists various systems of the excavator including the undercarriage, engine, hydraulic components, and attachments. Each item listed provides the part number, description, quantity, and reference page for more details. The document contains detailed parts lists and diagrams for components like the lower frame, track roller, idler, travel motor, and slew bearing.
Takeuchi tb016 compact excavator parts catalogue manual sn11610001 and upfjsekdhjenmdn
This document provides a parts list for a construction machine. It includes 3 tables that list parts for the lower frame, crawler belt, and track roller assemblies. Each table includes the part number, description, quantity, and other details for individual parts that make up each assembly.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 6zl) serv...fjsekdhjenmdn
The document provides instructions for removing and installing the transmission oil pump and pump drive gear on a D5C III track-type tractor. Key steps include draining the transmission oil, removing the tube assembly, plate, and transmission oil pump. The pump drive gear is then removed from the transmission case. Reinstallation involves reversing these steps, ensuring proper placement of seals and connection of hoses.
Caterpillar cat d5 c iii track type tractor dozer bulldozer (prefix 5hs) serv...fjsekdhjenmdn
This service repair manual provides instructions to remove and install final drives on D5C III track-type tractors. It outlines 33 steps to disassemble the final drive, including removing the final drive assembly, various gears, bearings, seals and other components. It then describes 35 steps to reassemble the front drive, including installing new seals, bearings, gears and other parts back into the final drive assembly. Safety procedures are provided to contain fluids and ensure proper cleaning, heating and installation of components.
Caterpillar cat 966 h wheel loader (prefix tal) service repair manual (tal000...fjsekdhjenmdn
This document provides instructions for disassembling and assembling the freewheel stator component of a torque converter. The disassembly process involves using various tools to remove over 30 individual parts in a specific sequence. Cleanliness is emphasized. The assembly process reverses the disassembly steps and provides additional details like proper orientation and torque specifications for fasteners.
Caterpillar cat 966 h wheel loader (prefix ryf) service repair manual (ryf000...fjsekdhjenmdn
This document provides instructions for disassembling and assembling the torque converter of a 966H wheel loader. It begins with required tools and safety notices. The disassembly instructions describe removing over 30 individual parts in multiple steps, including the torque converter housing, impeller, stator, carrier shaft, and turbine. The assembly section then lists the components and provides the reverse order for reassembling the torque converter. Cleanliness is emphasized as important during disassembly and assembly.
Caterpillar cat 966 h wheel loader (prefix bj6) service repair manual (bj6000...fjsekdhjenmdn
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar C11 engine. The removal procedure involves using various tools to remove 12 different components in 11 steps. The installation procedure involves 14 steps of reinstalling components and includes notes about properly aligning bearings and applying threadlock. Tolerances and torque specifications are provided for correctly installing some components.
Caterpillar cat 962 k wheel loader (prefix x4t) service repair manual (x4t000...fjsekdhjenmdn
This document provides instructions for disassembling and assembling the piston pump of the steering system on a Caterpillar 962K wheel loader. The disassembly procedure outlines 28 steps to remove components like bolts, valves, spools, springs, and bearings. The assembly procedure describes 34 steps and cautions to install these components in reverse order and ensure proper spring tension, seals, and shaft clearance. Precautions are included to prevent injury from parts under spring force.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjsekdhjenmdn
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, and tightening bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts.
Caterpillar cat 962 k wheel loader (prefix fll) service repair manual (fll000...fjsekdhjenmdn
The document provides instructions for disassembling and assembling the piston pump of the steering system on a 962K wheel loader. It describes 28 steps to disassemble the pump by removing components like bolts, valves, spools, springs, and bearings. It then describes 31 steps for reassembling the pump by reversing the disassembly process and ensuring proper installation of O-rings, seals, plates, and tightened bolts. The overall document provides a detailed technical procedure for maintenance or repair of the steering system piston pump.
Caterpillar cat 320 l track type excavator (prefix 9kk) service repair manual...fjsekdhjenmdn
The document provides instructions for removing and installing the idler gear of an excavator engine. It begins by noting the required tools and importance of alignment marks. The removal procedure instructs to remove the idler gear bolt and washer, then remove the thrust plate from the idler gear shaft. Tooling is then used to pull the idler gear off the shaft. The installation procedure is not shown, but presumably involves reversing the removal steps.
Caterpillar cat 320 l track type excavator (prefix 7wk) service repair manual...fjsekdhjenmdn
This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including installing a crankshaft rear seal carrier, installing a crankshaft wear sleeve, and removing and installing a flywheel housing. The document lists required tools and provides step-by-step instructions with illustrations for each procedure.
Caterpillar cat 320 l track type excavator (prefix 1kl) service repair manual...fjsekdhjenmdn
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and valve seals on Caterpillar 3064 and 3066 engines. The procedures include using various specialty tools to compress springs, extract components, and properly seat new parts. Technicians are advised to keep components clean and lubricate parts during installation.
Caterpillar cat 320 track type excavator (prefix 9 kk) service repair manual ...fjsekdhjenmdn
The document provides instructions for removing and installing the idler gear of an excavator engine. It begins by noting the required tools and importance of alignment marks. The removal procedure instructs to remove the idler gear bolt and washer, then remove the thrust plate from the idler gear shaft. Tooling is then used to pull the idler gear off the shaft. The installation procedure is not shown, but presumably involves reversing the removal steps.
Caterpillar cat 320 track type excavator (prefix 7 wk) service repair manual ...fjsekdhjenmdn
This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including:
1) Installing the crankshaft rear seal and sleeve using a special tooling set.
2) Removing and installing the crankshaft rear seal carrier using gasket sealant and thread lock compound.
3) Removing and installing the flywheel housing using link brackets and gasket sealant.
Caterpillar cat 320 track type excavator (prefix 1 kl) service repair manual ...fjsekdhjenmdn
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and valve seals on Caterpillar 3064 and 3066 engines. The procedures include using various specialty tools to compress springs, extract components, and properly seat new parts. Technicians are advised to keep components clean and lubricate parts during installation.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...fjsekdhjenmdn
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix fr5) service rep...fjsekdhjenmdn
The document provides instructions for removing and installing various components of a 305.5E2 CR Mini Hydraulic Excavator FR5 engine, including the fuel manifold rail, fuel injection lines, electronic unit injector, turbocharger, exhaust gas recirculation valve, and more. The steps describe draining fluids, removing bolts, clamps and other hardware, and installing components in reverse order, noting proper torque specifications for reinstallation. Safety warnings are provided throughout regarding hazards such as high pressure fuel, sulfuric acid, and hot coolant.
Takeuchi tb108 compact excavator parts catalogue manual sn10810004~10812001fjsekdhjenmdn
This document provides an index and parts list for a TB108 excavator with serial numbers between 10810004-10812001. The index lists various systems of the excavator including the undercarriage, engine, hydraulic components, and attachments. Each item listed provides the part number, description, quantity, and reference page for more details. The document contains detailed parts lists and diagrams for components like the lower frame, track roller, idler, travel motor, and slew bearing.
Takeuchi tb016 compact excavator parts catalogue manual sn11610001 and upfjsekdhjenmdn
This document provides a parts list for a construction machine. It includes 3 tables that list parts for the lower frame, crawler belt, and track roller assemblies. Each table includes the part number, description, quantity, and other details for individual parts that make up each assembly.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
11. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 1.1.1
General
GENERAL Introduction
The enclosed CLAAS-REPAIR-MANUAL is intended
to help maintain the continuous readiness for opera-
tion, and thus the high value, of the CLAAS forage har-
vester, by dedicated care and customer service
technical monitoring.
The experience of our customer service technicians
and the experience gained in the factory is gathered
together in this REPAIR-MANUAL.
The sequence of illustrations shows the progression of
each repair process, the text provides more informa-
tion in the form of the notes required for the setting, the
use of the CLAAS special tools etc.
This includes the representation of the most important
repairs so that individual and small tasks can be
extracted and followed easily.
The CLAAS-REPAIR-MANUAL is designed as a
loose-leaf binder.
It is added to continuously in the course of further
technical developments of the machines and is
therefore always an up-to-date reference document.
For safety reasons, we would ask you always to
compare the setting values and filling volumes with the
currently-valid operating instructions of the individual
machine.
CLAAS KGaA mbH
Service Department
General
12. 1.1.2 RHB JAGUAR 900 – 830 Profistar / Speedstar - 0298 826.1
General
Introduction to the CLAAS Repair Manual The CLAAS-REPAIR-MANUAL is divided into main
groups and sub-groups.
With regard to the numbering at the foot of each page,
the first figure indicates the main group, the figure
behind the point is the sub-group and the figure after
the second point is the page number. In each
sub-group, the illustrations and pages are continuously
numbered starting from 1.
Differences between machine types are indicated by
text or illustration notes. Fitting procedures which are
valid for all machine types referred to in this manual,
are kept neutral.
In the case of additions, the sub-groups are added to
or replaced. Any additions are filed under the relevant
main group/sub-group and the index is replaced.
The picture symbols serve to provide quick orientation
in the case of recurring fitting procedures. Their signifi-
cance is described at the beginning of this book.
Extensive descriptions are given under the designation
“GENERAL REPAIR NOTES” at the beginning of this
book. Read and observe these important notes. They
provide the basis for safe and long-term operation
after repair work.
The index for the relevant main group/sub-group
provides easy, quick access to all fitting descrip-
tions.
14. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 2.1.1
Cab
CAB
Removing front frame
Remove screen (A).
(Fig. 1)
Remove the windscreen wiper (B).
Unscrew the wiper motor (D) from the front plate.
(Fig. 2)
Remove the air ducting (E) from the left and right hand
sides.
(Fig. 3)
Unscrew the doors (F) on the left and right hand sides
from the side wall at the hinge.
(Fig. 4)
A
1
D
B
2
E
3
F
4
Cab
15. 2.1.2 RHB JAGUAR 900 – 830 Profistar / Speedstar - 0298 826.1
Cab
Remove blind (G).
(Fig. 5)
Unscrew the clamp (H) and hex head bolt (K).
(Fig. 6)
Unscrew the four plate screws at the front of the roof
lining (L).
(Fig. 7)
Carefully pull the front of the roof lining (L) downwards.
Remove the four hex head bolts from the upper front
screen.
(Fig. 8)
G
5
K
H
6
L
7
L
8
16. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 2.1.3
Cab
Also remove the four hex head bolts on both the left
and right hand sides of the front screen frame.
(Fig. 9)
Unscrew the three hex head bolts (O) on the lower
front screen frame.
Unscrew the holders (P) on the left and right hand
sides.
Remove the front screen complete with front screen
frame, if necessary using a suitable suction device.
Caution!
The front screen frame is fitted using sealant
around the entire frame. When removing the
front screen, the sealant must be cut out in
steps using a sharp knife.
Danger!
The front screen must not be compressed or
stretched excessively during the removal
process, since it can become stressed and
lead to cracking.
Always wear gloves during the entire
removal process.
– Danger of injury –
(Fig. 10, 11)
9
O
10
P
11
17. 2.1.4 RHB JAGUAR 900 – 830 Profistar / Speedstar - 0298 826.1
Cab
Fitting the front frame
Caution!
Before fitting, the front screen frame and the
connection points on the cab must be cleaned to
remove any traces of sealant
1. Apply liquid sealant, e.g. Sikaflex-255 FC-black,
(Part no. 0320 808.0), to the entire circumference
of the front screen frame.
2. The front screen should be lifted to a position in
front of the cab, if necessary using a suitable
suction device, then screw in the three hex head
bolts (O) on the lower front screen frame, and
then screw in the four hex head bolts (N) on each
of the side front screen frames on the left and right
hand sides.
3. Screw on the holders (P) on the left and right hand
sides.
(Fig. 12, 13)
4. Screw in the four hex head bolts on the upper
screen frame.
(Fig. 14)
O
P
P
12
13
14
18. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 2.1.5
Cab
5. Screw back the roof lining (L) at the front edge
using the four plate screws onto the upper front
screen frame.
(Fig. 15)
6. Screw back the clamp (H) and hex head bolt (K).
(Fig. 16)
7. Screw back the panel (G).
(Fig. 17)
8. Screw back the doors (F) on the left and right
hand sides from the side wall at the hinge.
(Fig. 18)
L
15
K
H
16
G
17
F
18
19. 2.1.6 RHB JAGUAR 900 – 830 Profistar / Speedstar - 0298 826.1
Cab
9. Refit the air ducting (E) on the left and right hand
sides.
(Fig. 19)
10. Screw the wiper motor (D) back onto the front
screen.
11. Screw back the wipers (B).
(Fig. 20)
12. Screw back the blind (A).
(Fig. 21)
E
19
D
B
20
A
21
20. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 2.2.1
Heating
HEATING
Removing the heating elements
Completely open the cab heating regulating valve
using the rotary knob (A).
(Fig. 1)
Drain about 5 Litres of coolant through he drain
cock (B) and collect in a suitable container.
Environment!
The coolant should be disposed of in a proper way.
After draining, the drain cock (B) should be tightly
closed again.
(Fig. 2)
Hinge up the cab roof.
Unscrew the cover (C) from the top of the cab.
(Fig. 3)
A
1
B
2
C
3
Heating
21. 2.2.2 RHB JAGUAR 900 – 830 Profistar / Speedstar - 0298 826.1
Heating
Unscrew the gas struts (D) on the left and right hand
sides of the cab upper area at (E).
Remove the front air filter (V).
Lift the cab roof and fit a mounting bracket (M
self-made) on the left and right hand side further
forwards and fix to an existing hex head bolt.
(Fig. 4, 5)
Release the hose clamps (G) of the heating hoses (H
and P) from the heater body (K) and pull off the
heating hoses. Collect the coolant which comes out.
Environment!
The coolant should be disposed of in a proper way.
(Fig. 6, 7)
D
V
E
4
M
5
G
H
6
K
P
G
7
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 2.2.3
Heating
Unscrew the bracket (L) from the side wall of the cab.
(Fig. 8)
Pull out the heating element (K) upwards. Collect any
coolant which leaks out while doing this.
Environment!
The coolant should be disposed of in a proper way.
(Fig. 9)
Fitting the heating element
Caution!
Before fitting, check the hoses for damage and
replace if necessary.
1. Insert the heating element (K) into the top of the
cab.
2. Fix the bracket (L) to the side of the cab in such a
way that the heating element (K) is in good
contact at (M and N).
(Fig. 10)
L
8
K
9
L
NM
K
10
24. 2.2.4 RHB JAGUAR 900 – 830 Profistar / Speedstar - 0298 826.1
Heating
3. Fit the heating hoses (H and P) using the hose
clamps (G) on the heating body (K).
(Fig. 11, 12)
4. Fit the gas struts (D) to the left and right hand
sides at (E) using new locknuts on the top of the
cab in such a way that there is a small amount of
play.
5. Fit the front air filter (V).
(Fig. 13)
6. Screw the cover (C) to the top of the cab.
(Fig. 14)
K
P
G
11
G
H
12
D
V
E
13
C
14
25. 0298 826.1 - RHB JAGUAR 900 – 830 Profistar / Speedstar 2.2.5
Heating
7. Pouring in the coolant:
– Pour the coolant in through the filling spigot at (E)
until it reaches the sight glass (F).
– Start the diesel engine and let it run with fully open
regulating valve for a short period of time.
– Check the coolant level once again.
Coolant quantity/type – see page 1.5.1, Lubri-
cants chart.
(Fig. 1, 15, 16)
Removing the regulating valve
Completely open the cab heating regulating valve
using the rotary knob (A).
(Fig. 17)
Drain about 5 Litres of coolant through he drain
cock (B) and collect in a suitable container.
Environment!
The coolant should be disposed of in a proper way.
After draining, the drain cock (B) should be tightly
closed again.
(Fig. 18)
E
15
F
16
A
17
B
18