This document provides instructions for servicing components of a 320/320L track-type excavator powered by a 3116 engine, including installing a crankshaft rear seal carrier, installing a crankshaft wear sleeve, and removing and installing a flywheel housing. The document lists required tools and provides step-by-step instructions with illustrations for each procedure.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929732
Crankshaft Wear Sleeve (Rear) - Install
SMCS - 1161-012-ZV
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C(1)
132-8772 Seal Locator 1
D(1)
1U-7596 Bolt 2
E(1)
1U-7597 Sleeve Ring 1
F(1)
1U-7594 Seal Installer 1
G(1)
9S-8858 Nut 1
(1)
Part of the 1U-7598 Seal Installer
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the rear of the crankshaft is thoroughly clean and dry prior to the installation of
the crankshaft rear seal.
1/3(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g01003875
2. Fasten Tooling (C) to the rear of the crankshaft with Tooling (D). Hand tighten Tooling (D).
3. Position the crankshaft rear seal and crankshaft rear sleeve (1) on Tooling (C). Position
Tooling (E) on Tooling (C).
Illustration 2 g01003866
Typical example
4. Position Tooling (F) over Tooling (C) and Tooling (E). Install Tooling (G). Tighten Tooling
(G) in order to install the crankshaft rear seal and the crankshaft wear sleeve.
5. Remove Tooling (G), Tooling (F), and Tooling (E). Turn over Tooling (E). Install Tooling
(E), Tooling (F), and Tooling (G). Tighten Tooling (G) in order to complete the installation
of the crankshaft rear seal and the crankshaft wear sleeve.
6. Remove Tooling (G) and Tooling (F). Check Tooling (E) and Tooling (C). The faces of
Tooling (E) and Tooling (C) will be flush if the crankshaft rear seal and the crankshaft wear
sleeve are properly installed. Refer to the Specifications module for more information.
7. Remove Tooling (E), Tool (E), and Tooling (C).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
2/3(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01987820
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
Start By:
a. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 1 g01027007
1. Remove bolts (1).
2. Remove rear seal carrier (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-8440 Component Cleaner
B 169-5464 Quick Cure Primer
C 1U-8846 Gasket Sealant
D 9S-3263 Thread Lock Compound
NOTICE
Keep all parts clean from contaminants.
2/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01027007
1. Clean the joint face of rear seal carrier (2) and the cylinder block with Tooling (A).
2. Apply Tooling (B) to the joint face of rear seal carrier (2). Allow the primer to air dry for
three to five minutes.
Note: Tooling (C) is used on the joint face of rear seal carrier (2). Do not allow the sealant
to get into the oil passage in the mounting face of the cylinder block.
3. Apply Tooling (C) to the joint face of rear seal carrier (2). Spread the sealant uniformly.
Rear seal carrier (2) must be installed within ten minutes of application of the sealant.
4. Position rear seal carrier (2) on the dowels in the rear of the cylinder block.
5. Apply Tooling (D) on the threads of bolts (1). Install bolts (1) that hold rear seal carrier (2)
to the cylinder block.
End By:
a. Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing -
Remove and Install".
3/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01981940
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01027146
1. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1).
2. Remove bolts (2) and bolt (3) that fastens the flywheel housing to the cylinder block.
3. Remove bolts (4). Remove flywheel housing (1). The weight of flywheel housing (1) is
approximately 25 kg (55 lb).
Installation Procedure
Table 2
Required Tools
2/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
B 1U-8846 Gasket Sealant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
Illustration 2 g01027146
2. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb). Position flywheel housing (1) on the
cylinder block. Install bolts (4).
3. Install bolts (2) and bolt (3).
End By:
3/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 11:10:47 UTC+0800 2019
4/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929931
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 1 g00691836
1. Remove bolts (2), crankshaft vibration damper (3), and spacers from the crankshaft pulley.
Note: For information on the reusability of the vibration damper on 3114 and 3116 engines,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8220, "Specifications
for Damper Inspection 3114 and 3116 Engines".
2. Loosen the tension on water pump drive belt (1). Remove the belt from the crankshaft
pulley.
Illustration 2 g00691831
3. Remove bolts (4) and the washers.
4. Remove crankshaft pulley (5).
Note: For information on the reusability of the crankshaft pulley, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8046, "Cast Iron and Steel Pulleys".
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
2/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00691831
1. Position crankshaft pulley (5) on the crankshaft. Install bolts (4) and tighten the bolts to a
torque of 160 ± 30 N·m (118 ± 22 lb ft).
Note: For information on the reusability of the crankshaft pulley, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8046, "Cast Iron and Steel Pulleys".
Illustration 4 g00691836
2. Install water pump drive belt (1).
Note: Check the alignment marks on the rubber vibration dampers for proper alignment.
The rubber vibration damper should be replaced if the rubber vibration damper is out of
alignment. Refer to Specifications, "Vibration Damper".
3. Install spacers and crankshaft vibration damper (3). Tighten bolts (2) to a torque of
55 ± 10 N·m (40 ± 7 lb ft).
Note: For information on the reusability of the vibration damper on 3114 and 3116 engines,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8220, "Specifications
for Damper Inspection 3114 and 3116 Engines".
3/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. 4. Adjust the tension of water pump drive belt (1). Refer to the Specifications Module, "Belt
Tension Chart". Also, refer to the Operation and Maintenance Manual, "Belt - Inspect".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 11:11:43 UTC+0800 2019
4/4(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01982085
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 1 g00989224
1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 11:12:39 UTC+0800 2019
2/2(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01982092
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Illustration 1 g00989228
1. Use Tooling (C) to install crankshaft front seal (1).
Note: The crankshaft seal is designed to be installed dry.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 11:13:35 UTC+0800 2019
2/2(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320-A EXCAVATOR 7WK
Configuration: 320, 320L TRACK-TYPE EXCAVATORS 7WK00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01176651
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Illustration 1 g00629709
Note: It is not necessary to remove the vibration damper and the crankshaft pulley in order
to remove the front cover.
1. Remove bolts (1) from front cover (2).
2. Remove front cover (2) and the gasket from the front of the engine.
1/2(W)
w
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...