This document is an operation and maintenance manual for TH414C GC and TH417C GC telehandler models produced after specific serial numbers. It contains safety information, pre-operation checks, controls information, operating instructions, and maintenance procedures. The manual has sections covering general safety practices, inspections, controls, engine operation, loading and transport, approved attachments, capacity charts, and instructions for specific attachments. It is intended to be kept with the machine at all times for reference by operators.
Caterpillar cat th255 c telehandler operator and maintenance manualudjfjjskekkem
This document provides an operations and maintenance manual for a telehandler model TH255C. It contains 9 sections that cover general safety practices, pre-operation checks, controls and indicators, operation instructions, attachments and hitches, emergency procedures, maintenance, additional checks, and specifications. The manual emphasizes following approved procedures, wearing proper safety gear, understanding capacity limits, avoiding electrical hazards, preventing tip overs, and using caution when traveling, lifting loads, and operating on slopes.
New holland w230 c tier 4 wheel loader service repair manualufjjsefkksemme
This document provides instructions for removing the engine from a wheel loader. It involves marking components for reinstallation, draining fluids like coolant and oil, disconnecting batteries, and using lifting straps to remove the engine. Key steps include draining the radiator and oil pan, disconnecting electrical and hydraulic connections, and safely lifting the engine out. Safety precautions are described like releasing air pressure from reservoirs.
New holland w170 b wheel loader service repair manualufjjsefkksemme
This document provides instructions for removing the engine and radiator from a W170B wheel loader. The key steps include draining fluids, disconnecting wiring harnesses and hoses, removing the hood, and using lifting straps to remove the engine. Safety procedures are described such as discharging pressure from hydraulic and brake systems before removal.
New holland w80 btc wheel loader service repair manualufjjsefkksemme
This repair manual provides technical information for engineers to service wheel loaders models W50BTC, W60BTC, W70BTC, and W80BTC. It consists of two volumes, one covering the wheel loaders and one covering the engine. The manual contains information on repair procedures, necessary tools, and service standards. It is important for technicians to carefully read this manual to correctly repair the machines and contact the manufacturer with any questions. Safety is emphasized, advising technicians to never attempt repairs while equipment is in motion.
New holland w60 c zb tier 4a (interim) compact wheel loader service repair ma...ufjjsefkksemme
This document is a service manual for New Holland compact wheel loaders models W50C, W60C, W70C, and W80C. It contains instructions for servicing and repairing components of the engine, fuel system, drive train, axles, brakes, hydraulics, electrical systems, cab, and front loader attachment. The manual provides detailed procedures for maintenance and overhaul of individual parts and systems.
New holland tc45 da tractor service repair manualufjjsefkksemme
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
Case 721 e tier3 z bar bagage suggar. wheel loader service repair manual [n8a...ufjjsefkksemme
This document is a service manual for the 721E wheel loader. It contains information on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform/cab components. The manual is organized by system with section numbers that correspond to components and procedures. It provides specifications, descriptions of how systems work, diagnostic and troubleshooting information, and service procedures.
New holland t8040 tractor service repair manualufjjsefkksemme
This document provides a summary of the hydraulic systems on a tractor model. It describes the primary hydraulic power system including the hydraulic pumps that power it. A tandem gear pump and PFC piston pump supply hydraulic flow. The priority/regulator valve distributes the flow based on priority, first to steering and then to other circuits like remote valves and hitches. Detailed diagrams and component identification are provided.
Caterpillar cat th255 c telehandler operator and maintenance manualudjfjjskekkem
This document provides an operations and maintenance manual for a telehandler model TH255C. It contains 9 sections that cover general safety practices, pre-operation checks, controls and indicators, operation instructions, attachments and hitches, emergency procedures, maintenance, additional checks, and specifications. The manual emphasizes following approved procedures, wearing proper safety gear, understanding capacity limits, avoiding electrical hazards, preventing tip overs, and using caution when traveling, lifting loads, and operating on slopes.
New holland w230 c tier 4 wheel loader service repair manualufjjsefkksemme
This document provides instructions for removing the engine from a wheel loader. It involves marking components for reinstallation, draining fluids like coolant and oil, disconnecting batteries, and using lifting straps to remove the engine. Key steps include draining the radiator and oil pan, disconnecting electrical and hydraulic connections, and safely lifting the engine out. Safety precautions are described like releasing air pressure from reservoirs.
New holland w170 b wheel loader service repair manualufjjsefkksemme
This document provides instructions for removing the engine and radiator from a W170B wheel loader. The key steps include draining fluids, disconnecting wiring harnesses and hoses, removing the hood, and using lifting straps to remove the engine. Safety procedures are described such as discharging pressure from hydraulic and brake systems before removal.
New holland w80 btc wheel loader service repair manualufjjsefkksemme
This repair manual provides technical information for engineers to service wheel loaders models W50BTC, W60BTC, W70BTC, and W80BTC. It consists of two volumes, one covering the wheel loaders and one covering the engine. The manual contains information on repair procedures, necessary tools, and service standards. It is important for technicians to carefully read this manual to correctly repair the machines and contact the manufacturer with any questions. Safety is emphasized, advising technicians to never attempt repairs while equipment is in motion.
New holland w60 c zb tier 4a (interim) compact wheel loader service repair ma...ufjjsefkksemme
This document is a service manual for New Holland compact wheel loaders models W50C, W60C, W70C, and W80C. It contains instructions for servicing and repairing components of the engine, fuel system, drive train, axles, brakes, hydraulics, electrical systems, cab, and front loader attachment. The manual provides detailed procedures for maintenance and overhaul of individual parts and systems.
New holland tc45 da tractor service repair manualufjjsefkksemme
This document is the contents page for a repair manual for New Holland TC35A, TC35DA, TC40A, TC40DA, TC45A, and TC45DA tractors. It lists the sections and chapters contained within the repair manual, including the engine, clutch, transmission, driveline, front and rear axles, brakes, hydraulic system, steering, climate control, electrical systems, and platform. The document provides an overview of the complete contents and organization of the repair manual.
Case 721 e tier3 z bar bagage suggar. wheel loader service repair manual [n8a...ufjjsefkksemme
This document is a service manual for the 721E wheel loader. It contains information on the engine, transmission, front and rear axle systems, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, and platform/cab components. The manual is organized by system with section numbers that correspond to components and procedures. It provides specifications, descriptions of how systems work, diagnostic and troubleshooting information, and service procedures.
New holland t8040 tractor service repair manualufjjsefkksemme
This document provides a summary of the hydraulic systems on a tractor model. It describes the primary hydraulic power system including the hydraulic pumps that power it. A tandem gear pump and PFC piston pump supply hydraulic flow. The priority/regulator valve distributes the flow based on priority, first to steering and then to other circuits like remote valves and hitches. Detailed diagrams and component identification are provided.
New holland t6070 tractor service repair manualufjjsefkksemme
The document is a service manual that provides technical specifications, diagrams, and repair instructions for the hydraulic, pneumatic, electrical, and electronic systems of tractor models T6010 through T6070. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, electrical power system, electronic systems, and fault codes. The primary hydraulic power system section provides specifications, diagrams, and descriptions of fixed and variable displacement hydraulic pumps and the charge pump.
Case 621 g wheel loader zbar eh, new cab tier4b na wheel loader service repai...ufjjsefkksemme
This document is a service manual that provides specifications and repair/maintenance instructions for 621G and 721G wheel loaders. It contains sections covering the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, electrical systems, loader arm/bucket, and other components. The document includes an introduction on safety practices and machine identification.
New holland t3040 tractor service repair manualufjjsefkksemme
This document is a service manual for T3010, T3020, T3030, and T3040 tractors. It contains sections on general guidelines, the engine, clutch, transmissions, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, cab air conditioning, and electrical systems. Each section provides specifications, torque settings, removal and installation instructions, troubleshooting, and disassembly/assembly procedures for maintaining and repairing the components.
Case 321 f hs compact wheel loader service repair manualufjjsefkksemme
The document provides instructions for removing an engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluid systems, and using safety pins to secure the machine before removing the engine. Key steps include turning the ignition to allow hydraulic systems to cool, switching the battery main switch to the off position, and tagging and disconnecting specific components like sensors, fans, and condenser hoses.
Case 221 f hs tier 4 compact wheel loader service repair manualufjjsefkksemme
This service manual provides information on servicing a compact wheel loader, including the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, and electrical systems. It contains sections on maintenance and repair procedures with references to specific components by section number. Proper service requires using original parts and qualified personnel.
New holland t8.410 tractor service repair manual (pin zfre03123 and above)ufjjsefkksemme
This service manual provides information for servicing the engines, transmissions, axles, hydraulics, electrical systems, and other components of T8 tractor models 320-410 with Powershift transmissions. The manual includes specifications, maintenance procedures, and troubleshooting information to assist technicians with repairs and maintenance.
New holland kobelco e235 sr crawler excavator service repair manualufjjsefkksemme
The document provides safety precautions and general guidelines for disassembling, repairing, and maintaining the E235SR excavator. Some key points include:
- Clean the excavator before bringing it into the repair shop to make work more efficient and prevent damage.
- Wear appropriate protective equipment like safety shoes, glasses and remove jewelry when working. Support or block components before disassembling.
- Relieve pressure from hydraulic systems before disconnecting lines and drain fluids before removing components.
- Clean and inspect disassembled parts, measure wear and clearances. Apply new seals and grease before reassembling.
- Bleed air from hydraulic systems after reassembly and refilling fluids
New holland eh130 crawler excavator service repair manualufjjsefkksemme
This document is the service manual for the EH130 crawler excavator. It contains 6 sections that provide specifications, maintenance procedures, system descriptions, disassembly/assembly instructions, troubleshooting, and engine information. The table of contents lists the chapters for each of these sections, including safety information, specifications, maintenance standards, hydraulic, electrical and other systems, components, troubleshooting guides, and the engine. The safety section provides general safety information and precautions regarding the safe operation, inspection and maintenance of the excavator.
New holland eh35 compact excavator service repair manualufjjsefkksemme
This document is a service manual for an EH35 compact excavator. It contains 7 sections that cover specifications, maintenance, systems, disassembly, troubleshooting, the engine, and miscellaneous topics. The sections are further broken down into chapters that provide details on tools, maintenance schedules, hydraulic and electrical systems, component removal and installation, and troubleshooting guides for hydraulic, electrical and engine issues. Safety precautions are outlined that must be followed when operating or servicing the excavator.
New holland eh15 hydraulic excavator service repair manualufjjsefkksemme
This document is a service manual for the EH15 hydraulic excavator. It contains specifications, maintenance procedures, troubleshooting guides, and component level descriptions for the excavator. The manual is divided into multiple sections covering general information, specifications, systems, components, troubleshooting, and the engine. It provides technical information and instructions to aid in servicing and repairing the EH15 excavator.
New holland e18 c cab tier iv engine mini excavator service repair manualufjjsefkksemme
This service manual provides information on servicing the engine, hydraulic systems, frames and ballasting, tracks and track suspension, electrical systems, booms, dippers, buckets, dozer blade and arm, platform, cab, bodywork, and decals for the E18C Mini Excavator. The manual includes sections on safety, the engine, hydraulic systems, electrical systems, and various mechanical components of the excavator.
Hyster k005 (h4.00 xm europe) forklift service repair manualufjjsefkksemme
This document provides repair instructions for various components of a forklift, including:
1. The counterweight can be removed using lifting eyebolts and a lifting device, taking precautions about stability and weight.
2. The hood can be removed by disconnecting gas cylinders and wiring, and must be properly adjusted upon installation for operator restraint.
3. The overhead guard is removed using lifting devices and fasteners, and its isolators should be inspected. LED backup lights are non-repairable units.
Hyster d005 (h70 e europe) forklift service repair manualufjjsefkksemme
This document provides instructions for servicing GM engines. It describes removing and installing the cylinder head and valve mechanism. Key steps include using a compressor tool to remove the valve springs, cleaning carbon from the combustion chambers, inspecting the valves and valve guides for wear, and checking clearances. The valve seats can be repaired with a cutter tool if damaged, or the cylinder head replaced if not repairable. Rocker arm studs should also be replaced if damaged.
Hyster d010 (s30 xm) forklift service repair manualufjjsefkksemme
The document provides an overview of the operation of a single-speed powershift transmission. It describes the main components, including the torque converter, clutch assemblies, control valve, and hydraulic system. The summary is:
The transmission uses a torque converter and two clutch assemblies to provide forward and reverse gearing through hydraulic actuation. Oil flow through the transmission pump, control valve, and hydraulic circuits applies the clutches and provides lubrication. The control valve regulates clutch pressure and directs oil flow to smoothly engage the transmission during gear changes.
Hyster b187 (s2.50 xl europe) forklift service repair manualufjjsefkksemme
This document provides service procedures for the brake system on a lift truck model. It describes the main components of the brake system including the master cylinder, wheel cylinders, brake shoes, parking brake system, and linkage. Removal and disassembly procedures are provided for the 260mm service brakes. Inspection and cleaning instructions are also included to ensure safe handling of any asbestos materials that may be present.
Jcb 456 wheeled loading shovel service repair manual from 539000ufjjsefkksemme
This document provides information about identifying machines and their components, standard torque settings for fasteners, and hydraulic connection types. It includes details about machine identification plates, vehicle identification numbers, product identification numbers, and component plates. Tables are provided with torque settings for UNF and metric fasteners under lubricated and unlubricated conditions. Information is also given on 'O' ring face seal and 'torque stop' hose hydraulic connection systems.
Jcb 446 wheeled loading shovel service repair manual from 540013ufjjsefkksemme
This document provides information for servicing JCB 446 and 456 Wheeled Loading Shovel models, including:
- Sections covering general information, safety, maintenance, attachments, body/framework, electrics, hydraulics, transmission, brakes, steering, and engine.
- Instructions on identifying machines by identification plate, vehicle identification number, and product identification number.
- Standard torque settings for fasteners.
- Descriptions of hydraulic connection types.
- Lists and references for service tools.
- Information on sealing compounds and color coding.
- Instructions for machine preparation for towing.
Caterpillar cat th414 c gc, th417c gc telehandler operator and maintenance ma...ufjjsefkksemme
This document is an operation and maintenance manual for JLG telehandlers models TH414C GC, TH417C GC. It contains safety information and instructions for pre-operation checks, operation, maintenance and repairs. The manual covers hazards from electrical contact, tipping over, load falling, pinch points and proper procedures for lifting loads, traveling, parking and emergency situations. Maintenance schedules and lubrication instructions are also included.
Caterpillar cat th360 b telehandler parts catalogue manual sn tbh00100 thru t...ufjjsefkksemme
This document provides parts information for a TH360B Telehandler including:
- A crankshaft group listing 9 parts including the crankshaft and main and rod bearing sets.
- A cylinder block group listing 17 parts including the cylinder block, plugs, and piston cooling jets.
- A cylinder head group listing 14 parts including the cylinder head, valves, springs, and seals.
Caterpillar cat th414 c gc, th417c gc telehandler operator and maintenance ma...ufjjsefkksemme
This document is an operation and maintenance manual for TH414C GC and TH417C GC telehandler models produced after specific serial numbers. It contains safety information, pre-operation checks, controls information, operating instructions, and maintenance procedures. The manual has sections covering general safety practices, inspections, controls, engine operation, loading and transport, approved attachments, capacity charts, and instructions for specific attachments. It is intended to be kept with the machine at all times for reference by operators.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
New holland t6070 tractor service repair manualufjjsefkksemme
The document is a service manual that provides technical specifications, diagrams, and repair instructions for the hydraulic, pneumatic, electrical, and electronic systems of tractor models T6010 through T6070. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, electrical power system, electronic systems, and fault codes. The primary hydraulic power system section provides specifications, diagrams, and descriptions of fixed and variable displacement hydraulic pumps and the charge pump.
Case 621 g wheel loader zbar eh, new cab tier4b na wheel loader service repai...ufjjsefkksemme
This document is a service manual that provides specifications and repair/maintenance instructions for 621G and 721G wheel loaders. It contains sections covering the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, electrical systems, loader arm/bucket, and other components. The document includes an introduction on safety practices and machine identification.
New holland t3040 tractor service repair manualufjjsefkksemme
This document is a service manual for T3010, T3020, T3030, and T3040 tractors. It contains sections on general guidelines, the engine, clutch, transmissions, front and rear mechanical transmissions, power take-off, brakes, hydraulic systems, steering, cab air conditioning, and electrical systems. Each section provides specifications, torque settings, removal and installation instructions, troubleshooting, and disassembly/assembly procedures for maintaining and repairing the components.
Case 321 f hs compact wheel loader service repair manualufjjsefkksemme
The document provides instructions for removing an engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluid systems, and using safety pins to secure the machine before removing the engine. Key steps include turning the ignition to allow hydraulic systems to cool, switching the battery main switch to the off position, and tagging and disconnecting specific components like sensors, fans, and condenser hoses.
Case 221 f hs tier 4 compact wheel loader service repair manualufjjsefkksemme
This service manual provides information on servicing a compact wheel loader, including the engine, transmission, front and rear axle systems, brakes, hydraulic systems, frames and ballasting, steering, and electrical systems. It contains sections on maintenance and repair procedures with references to specific components by section number. Proper service requires using original parts and qualified personnel.
New holland t8.410 tractor service repair manual (pin zfre03123 and above)ufjjsefkksemme
This service manual provides information for servicing the engines, transmissions, axles, hydraulics, electrical systems, and other components of T8 tractor models 320-410 with Powershift transmissions. The manual includes specifications, maintenance procedures, and troubleshooting information to assist technicians with repairs and maintenance.
New holland kobelco e235 sr crawler excavator service repair manualufjjsefkksemme
The document provides safety precautions and general guidelines for disassembling, repairing, and maintaining the E235SR excavator. Some key points include:
- Clean the excavator before bringing it into the repair shop to make work more efficient and prevent damage.
- Wear appropriate protective equipment like safety shoes, glasses and remove jewelry when working. Support or block components before disassembling.
- Relieve pressure from hydraulic systems before disconnecting lines and drain fluids before removing components.
- Clean and inspect disassembled parts, measure wear and clearances. Apply new seals and grease before reassembling.
- Bleed air from hydraulic systems after reassembly and refilling fluids
New holland eh130 crawler excavator service repair manualufjjsefkksemme
This document is the service manual for the EH130 crawler excavator. It contains 6 sections that provide specifications, maintenance procedures, system descriptions, disassembly/assembly instructions, troubleshooting, and engine information. The table of contents lists the chapters for each of these sections, including safety information, specifications, maintenance standards, hydraulic, electrical and other systems, components, troubleshooting guides, and the engine. The safety section provides general safety information and precautions regarding the safe operation, inspection and maintenance of the excavator.
New holland eh35 compact excavator service repair manualufjjsefkksemme
This document is a service manual for an EH35 compact excavator. It contains 7 sections that cover specifications, maintenance, systems, disassembly, troubleshooting, the engine, and miscellaneous topics. The sections are further broken down into chapters that provide details on tools, maintenance schedules, hydraulic and electrical systems, component removal and installation, and troubleshooting guides for hydraulic, electrical and engine issues. Safety precautions are outlined that must be followed when operating or servicing the excavator.
New holland eh15 hydraulic excavator service repair manualufjjsefkksemme
This document is a service manual for the EH15 hydraulic excavator. It contains specifications, maintenance procedures, troubleshooting guides, and component level descriptions for the excavator. The manual is divided into multiple sections covering general information, specifications, systems, components, troubleshooting, and the engine. It provides technical information and instructions to aid in servicing and repairing the EH15 excavator.
New holland e18 c cab tier iv engine mini excavator service repair manualufjjsefkksemme
This service manual provides information on servicing the engine, hydraulic systems, frames and ballasting, tracks and track suspension, electrical systems, booms, dippers, buckets, dozer blade and arm, platform, cab, bodywork, and decals for the E18C Mini Excavator. The manual includes sections on safety, the engine, hydraulic systems, electrical systems, and various mechanical components of the excavator.
Hyster k005 (h4.00 xm europe) forklift service repair manualufjjsefkksemme
This document provides repair instructions for various components of a forklift, including:
1. The counterweight can be removed using lifting eyebolts and a lifting device, taking precautions about stability and weight.
2. The hood can be removed by disconnecting gas cylinders and wiring, and must be properly adjusted upon installation for operator restraint.
3. The overhead guard is removed using lifting devices and fasteners, and its isolators should be inspected. LED backup lights are non-repairable units.
Hyster d005 (h70 e europe) forklift service repair manualufjjsefkksemme
This document provides instructions for servicing GM engines. It describes removing and installing the cylinder head and valve mechanism. Key steps include using a compressor tool to remove the valve springs, cleaning carbon from the combustion chambers, inspecting the valves and valve guides for wear, and checking clearances. The valve seats can be repaired with a cutter tool if damaged, or the cylinder head replaced if not repairable. Rocker arm studs should also be replaced if damaged.
Hyster d010 (s30 xm) forklift service repair manualufjjsefkksemme
The document provides an overview of the operation of a single-speed powershift transmission. It describes the main components, including the torque converter, clutch assemblies, control valve, and hydraulic system. The summary is:
The transmission uses a torque converter and two clutch assemblies to provide forward and reverse gearing through hydraulic actuation. Oil flow through the transmission pump, control valve, and hydraulic circuits applies the clutches and provides lubrication. The control valve regulates clutch pressure and directs oil flow to smoothly engage the transmission during gear changes.
Hyster b187 (s2.50 xl europe) forklift service repair manualufjjsefkksemme
This document provides service procedures for the brake system on a lift truck model. It describes the main components of the brake system including the master cylinder, wheel cylinders, brake shoes, parking brake system, and linkage. Removal and disassembly procedures are provided for the 260mm service brakes. Inspection and cleaning instructions are also included to ensure safe handling of any asbestos materials that may be present.
Jcb 456 wheeled loading shovel service repair manual from 539000ufjjsefkksemme
This document provides information about identifying machines and their components, standard torque settings for fasteners, and hydraulic connection types. It includes details about machine identification plates, vehicle identification numbers, product identification numbers, and component plates. Tables are provided with torque settings for UNF and metric fasteners under lubricated and unlubricated conditions. Information is also given on 'O' ring face seal and 'torque stop' hose hydraulic connection systems.
Jcb 446 wheeled loading shovel service repair manual from 540013ufjjsefkksemme
This document provides information for servicing JCB 446 and 456 Wheeled Loading Shovel models, including:
- Sections covering general information, safety, maintenance, attachments, body/framework, electrics, hydraulics, transmission, brakes, steering, and engine.
- Instructions on identifying machines by identification plate, vehicle identification number, and product identification number.
- Standard torque settings for fasteners.
- Descriptions of hydraulic connection types.
- Lists and references for service tools.
- Information on sealing compounds and color coding.
- Instructions for machine preparation for towing.
Caterpillar cat th414 c gc, th417c gc telehandler operator and maintenance ma...ufjjsefkksemme
This document is an operation and maintenance manual for JLG telehandlers models TH414C GC, TH417C GC. It contains safety information and instructions for pre-operation checks, operation, maintenance and repairs. The manual covers hazards from electrical contact, tipping over, load falling, pinch points and proper procedures for lifting loads, traveling, parking and emergency situations. Maintenance schedules and lubrication instructions are also included.
Caterpillar cat th360 b telehandler parts catalogue manual sn tbh00100 thru t...ufjjsefkksemme
This document provides parts information for a TH360B Telehandler including:
- A crankshaft group listing 9 parts including the crankshaft and main and rod bearing sets.
- A cylinder block group listing 17 parts including the cylinder block, plugs, and piston cooling jets.
- A cylinder head group listing 14 parts including the cylinder head, valves, springs, and seals.
Caterpillar cat th414 c gc, th417c gc telehandler operator and maintenance ma...ufjjsefkksemme
This document is an operation and maintenance manual for TH414C GC and TH417C GC telehandler models produced after specific serial numbers. It contains safety information, pre-operation checks, controls information, operating instructions, and maintenance procedures. The manual has sections covering general safety practices, inspections, controls, engine operation, loading and transport, approved attachments, capacity charts, and instructions for specific attachments. It is intended to be kept with the machine at all times for reference by operators.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Caterpillar cat th414 c gc, th417c gc telehandler operator and maintenance manual sn nab00150 & after
1. Operation &
Maintenance Manual
Original Instructions
Keep this manual with machine at all times.
Models
TH414C GC
TH417C GC
S/N KRF00150 & After
S/N LYN00150 & After
S/N NAB00150 & After
S/N NMM00150 & After
31200957
Revised
October 1, 2014
2. Table of Contents
i31200957
TABLE OF CONTENTS
Revision Log
Read This First
Operator Qualifications ........................................................................... b
Modifications............................................................................................... b
Other Publications Available ................................................................. d
Table of Contents
Section 1 - General Safety Practices
1.1 Hazard Classification System ....................................................................1-1
Safety Alert System and Safety Signal Words...............................1-1
1.2 General Precautions .....................................................................................1-1
1.3 Operation Safety............................................................................................1-2
Electrical Hazards....................................................................................1-2
Tip Over Hazard.......................................................................................1-3
Travel Hazard............................................................................................1-6
Load Falling Hazard ...............................................................................1-7
Lifting Personnel.....................................................................................1-8
Driving Hazards on Slopes...................................................................1-9
Pinch Points and Crush Hazards.....................................................1-10
Fall Hazard..............................................................................................1-12
Chemical Hazards ................................................................................1-13
Section 2 - Pre-Operation and Inspection
2.1 Pre-Operation Check and Inspection.....................................................2-1
2.2 Safety Decals...................................................................................................2-3
2.3 Walk-Around Inspection.............................................................................2-6
2.4 Warm-Up and Operational Checks .........................................................2-8
Warm-Up Check ......................................................................................2-8
Operational Check..................................................................................2-8
2.5 Operator Cab...................................................................................................2-9
2.6 Windows........................................................................................................2-10
Cab Door Window ...............................................................................2-10
Rear Window .........................................................................................2-11
Section 3 - Controls and Indicators
3.1 General..............................................................................................................3-1
3.2 Controls.............................................................................................................3-2
Instrument Cluster..................................................................................3-4
Ignition .......................................................................................................3-6
Park Brake..................................................................................................3-7
Parking Procedure..................................................................................3-7
Transmission Control Lever (if equipped)......................................3-8
Table of Contents
3. Table of Contents
ii 31200957
Load Stability Indicator - LSI............................................................ 3-10
Steering Column Adjuster................................................................ 3-12
Joystick.................................................................................................... 3-14
Console Switches................................................................................. 3-20
Accessory Control Lever.................................................................... 3-22
3.3 Anti Theft ...................................................................................................... 3-23
3.4 Steer Modes ................................................................................................. 3-24
Manual Steering Alignment Mode Change............................... 3-24
3.5 Operator Seat .............................................................................................. 3-25
Operator Presence .............................................................................. 3-25
Adjustments.......................................................................................... 3-26
Seat Belt .................................................................................................. 3-27
3.6 Boom Indicators ......................................................................................... 3-28
Boom Extension................................................................................... 3-28
Section 4 - Operation
4.1 Engine ...............................................................................................................4-1
Starting the Engine................................................................................4-1
Battery Boosted Starting......................................................................4-2
Normal Engine Operation ...................................................................4-3
Shut-Down Procedure..........................................................................4-3
4.2 Operating with a Non-Suspended Load...............................................4-4
Lift Load Safely ........................................................................................4-4
Picking Up a Load...................................................................................4-4
Transporting a Load ..............................................................................4-5
Leveling Procedure................................................................................4-5
Placing a Load..........................................................................................4-6
Disengaging a Load...............................................................................4-6
4.3 Operating with a Suspended Load.........................................................4-7
Lift Load Safely ........................................................................................4-7
Picking Up a Suspended Load ...........................................................4-7
Transporting a Suspended Load.......................................................4-8
Leveling Procedure................................................................................4-8
Placing a Suspended Load..................................................................4-9
Disengaging a Suspended Load.......................................................4-9
4.4 Road Operation (CE).................................................................................. 4-10
4.5 Loading and Securing for Transport................................................... 4-11
Tiedown .................................................................................................. 4-11
Lifting....................................................................................................... 4-12
5. Table of Contents
iv 31200957
7.4 Lubrication Schedules.................................................................................7-8
TH414C GC................................................................................................7-8
TH417C GC................................................................................................7-9
7.5 Operator Maintenance Instructions.................................................... 7-10
Fuel System............................................................................................ 7-10
Tires .......................................................................................................... 7-12
Engine Oil............................................................................................... 7-14
Engine Cooling System ..................................................................... 7-15
Hydraulic Oil.......................................................................................... 7-16
Transmission Oil................................................................................... 7-17
Air Intake System................................................................................. 7-18
Cab Air Filters (if equipped)............................................................. 7-20
Battery ..................................................................................................... 7-22
Windshield Washer System (if equipped)................................... 7-23
Section 8 - Additional Checks
8.1 General..............................................................................................................8-1
8.2 Load Stability Indicator System ...............................................................8-1
8.3 Boom Interlock...............................................................................................8-2
Section 9 - Specifications
9.1 Product Specifications.................................................................................9-1
Fluids...........................................................................................................9-1
Capacities ..................................................................................................9-3
Tires .............................................................................................................9-4
Performance.............................................................................................9-5
Dimensions...............................................................................................9-6
Declaration of Vibration.......................................................................9-8
Noise Emission Level (CE)....................................................................9-8
Machine Towing Capacity...................................................................9-8
Index
Inspection, Maintenance and Repair Log
Transfer Of Ownership
6. Section 1 - General Safety Practices
1-131200957
SECTION 1 - GENERAL SAFETY PRACTICES
1.1 HAZARD CLASSIFICATION SYSTEM
Safety Alert System and Safety Signal Words
DANGER indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION indicates a potentiality hazardous situation which, if not avoided, may result in
minor or moderate injury.
1.2 GENERAL PRECAUTIONS
WARNING
Before operation, read & understand this manual. Failure to comply with the safety
precautions listed in this manual could result in machine damage, property damage,
personal injury or death.
DANGER OW0010
WARNING OW0021
CAUTION OW0031
7. Section 1 - General Safety Practices
1-2 31200957
1.3 OPERATION SAFETY
Note: The manufacturer has no direct control over machine application and operation.
Therefore, safety issues listed in this manual are non-exhaustive. The user and operator are
responsible for conforming with good safety practices.
Electrical Hazards
• This machine is not insulated and does not provide protection from contact or being
near electrical current.
• NEVER operate the telehandler in an area where overhead power lines, overhead or
underground cables, or other power sources may exist without ensuring the
appropriate power or utility company de-energizes the lines.
• Always check for power lines before raising the boom.
• Follow employer, local and governmental regulations for clearance from powerlines.
OW0040
10 FT
(3 M)
8. Section 1 - General Safety Practices
1-331200957
Tip Over Hazard
General
• For additional load requirements, refer to the appropriate capacity chart.
• Never use an attachment without the appropriate JLG approved capacity chart
installed on the telehandler.
• Understand how to properly use the capacity charts located in cab.
• DO NOT exceed rated lift capacity.
• Be sure that the ground conditions are able to support the machine.
• DO NOT raise boom unless frame is level (0 degrees), unless otherwise noted on
capacity chart.
• DO NOT level machine with boom/attachment above 1,2 m (4 ft).
(AUS - DO NOT level machine with load more than 300 mm (11.8 in) above ground
surface.)
OW0050
OW0080
OW0100
4 FT
(1,2 M)
9. Section 1 - General Safety Practices
1-4 31200957
• MAINTAIN proper tire pressure at all times. If proper tire pressures are not
maintained, this machine could tip over.
• Refer to manufacturer’s specifications for proper fill ratio and pressure requirements
for tires equipped with ballast.
• Always wear the seat belt.
• Keep head, arms, hands, legs and all other body parts inside operator’s cab at all times.
If the telehandler starts to tip over:
• DO NOT JUMP
• BRACE YOURSELF and STAY WITH THE MACHINE
• KEEP YOUR SEAT BELT FASTENED
• HOLD ON FIRMLY
• LEAN AWAY FROM THE POINT OF IMPACT
OH2291
OH20911
OH2221
10. Section 1 - General Safety Practices
1-531200957
Non-Suspended Load
• DO NOT drive with boom raised.
Suspended Load
• Tether suspended loads to restrict movement.
• Weight of all rigging (slings, etc.) must be included as part of load.
• Beware of wind. Wind can cause a suspended load to swing and cause dangerous side
loads - even with tag lines.
• DO NOT attempt to use telehandler frame-leveling to compensate for load swing.
• Keep heavy part of load closest to attachment.
• Never drag the load; lift vertically.
When driving with a suspended load:
• Start, travel, turn and stop slowly to prevent load from swinging.
• DO NOT extend boom.
• DO NOT raise the load more than 300 mm (11.8 in) above ground surface or the
boom more than 45°.
• DO NOT exceed walking speed.
OW0060
OW0150
11. Section 1 - General Safety Practices
1-6 31200957
Travel Hazard
• Steering characteristics differ between steer modes. Identify the steer mode settings
of the telehandler being operated.
• DO NOT change steer modes while traveling. Steer modes must be changed while
telehandler is stationary.
• Visually verify proper wheel alignment after each steer mode change.
• Ensure that adequate clearance is provided for both rear tail swing and front fork
swing.
• Look out for and avoid other personnel, machinery and vehicles in the area. Use a
spotter if you DO NOT have a clear view.
• Before moving be sure of a clear path and sound horn.
• When driving, retract boom and keep boom/attachment as low as possible while
maintaining visibility of mirrors and maximum visibility of path of travel.
• Always look in the direction of travel.
• Always check boom clearances carefully before driving underneath overhead
obstructions. Position attachment/load to clear obstacles.
• When driving in high speed, use only front wheel steer (if steering modes are
selectable).
• Telehandlers equipped with solid tires should not be used in applications requiring
excessive roading or driving extended distances. In the event an application requires
excessive roading or driving expanded distances, it is recommended to use
telehandlers not equipped with solid tires.
OAL2030
2-Wheel Front Steer 4-Wheel Circle Steer 4-Wheel Crab Steer
12. Section 1 - General Safety Practices
1-731200957
Load Falling Hazard
• Never suspend load from forks or other parts of carriage weldment. Use only JLG
approved lift points.
• DO NOT burn or drill holes in fork(s).
• Forks must be centered under load and spaced apart as far as possible.
OW0130
13. Section 1 - General Safety Practices
1-8 31200957
Lifting Personnel
• When lifting personnel, USE ONLY an approved personnel work platform, with proper
capacity chart displayed in the cab.
• DO NOT drive machine from cab when personnel are in platform.
OW0170
OW0190
14. Section 1 - General Safety Practices
1-931200957
Driving Hazards on Slopes
To maintain sufficient traction and braking capabilities, travel on slopes as follows:
• When unloaded, drive with forks pointed downhill.
• When loaded, drive with the forks pointed uphill.
• For additional travel requirements, refer to the appropriate capacity chart.
• To avoid overspeeding the engine and drivetrain when driving down slopes,
downshift to a lower gear and use the service brake as necessary to maintain a slow
speed. DO NOT shift into neutral and coast downhill.
• Avoid excessively steep slopes or unstable surfaces. To avoid tip over DO NOT drive
across excessively steep slopes under any circumstances.
• Avoid turning on a slope. Never engage “inching” or shift to “Neutral” when going
downhill.
• DO NOT park on a slope.
OW0200
15. Section 1 - General Safety Practices
1-10 31200957
Pinch Points and Crush Hazards
Stay clear of pinch points and rotating parts on the telehandler.
• Stay clear of moving parts while engine is running.
• Keep clear of steering tires and frame or other objects.
• Keep clear from under boom.
OW0210
OW0220
OW0230
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Section 1 - General Safety Practices
1-1131200957
• Keep clear of boom holes.
• Keep arms and hands clear of attachment tilt cylinder.
• Keep hands and fingers clear of carriage and forks.
• Keep others away while operating.
OW0240
OW0250
OW0260
OW0960
18. Section 1 - General Safety Practices
1-12 31200957
Fall Hazard
• Enter using the proper hand holds and steps provided. Always maintain 3-point
contact when mounting or dismounting. Never grab control levers or steering wheel
when mounting or dismounting the machine.
• DO NOT get off the machine until the shutdown procedure on page 4-3 has been
performed.
• DO NOT carry riders. Riders could fall off machine causing death or serious injury.
OW0280
OW0290