This document contains sections from a service manual for telehandlers, including:
1. Procedures for removing and installing components like the battery, alternator, starter motor, air cleaner, muffler, expansion tank, and radiator.
2. Steps for disassembling and assembling the radiator.
3. Torque specifications and troubleshooting information for engine, power train, hydraulic, electrical, and electronic systems.
4. Contents include service manual information, disassembly/assembly sections, and schematics for machine systems.
Caterpillar cat th580 b telehandler service repair manualudfjdfjjskekemm
This document contains removal and installation procedures for various components of a machine. Sections include the engine, powertrain, vehicle systems, machine components, electrical systems, and troubleshooting. Specific components covered include the battery, alternator, starter motor, air cleaner, muffler, expansion tank, radiator, and related brackets. Detailed steps are provided for draining fluids, disconnecting hoses and electrical connections, removing mounting hardware, and replacing components. Safety notices are included regarding hot or pressurized fluids, electrical hazards, and preventing accidental starting.
Caterpillar cat 951 c track loader (prefix 86j) service repair manual (86j040...ujjfjkskekmme
- The document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators.
- It describes removing over a dozen individual components of 42-MT, 37-MT and 41-MT series starting motors in step-by-step detail.
- Reassembly instructions are also provided, with an emphasis on applying the proper lubricants to bushings, seals and other parts.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...fjsekdmmeed
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 25 steps for reassembly, instructing technicians to clean parts, replace seals, apply lubricants, and reinstall components in reverse order using various tools. Technicians are advised to mark parts for orientation and take precautions when working with pressurized or spring-loaded components.
Case ih mx210 tractor service repair manualdfujsejfskekem
This document is the service manual for the MX Magnum tractor. It provides a table of contents that lists all sections and publications for servicing and repairing the tractor. Safety warnings are also provided, advising technicians to take proper precautions when working on the tractor, including wearing protective equipment, relieving pressure from hydraulic lines before disconnecting, and ensuring the engine is off and the tractor is blocked before performing any maintenance.
Caterpillar cat 349 d excavator (prefix klh) service repair manual (klh00001 ...cdsaas
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar cat th580 b telehandler service repair manualfusjefjskefkksem
This document provides removal and installation procedures for various components on a machine. It includes sections on removing and installing the battery, alternator, starter motor, air cleaner, muffler, and expansion tank. Detailed steps and illustrations are provided for each procedure. Safety precautions are also provided, such as warnings about hot components, electrical shock, and handling of chemicals.
Caterpillar cat th580 b telehandler service repair manualfjjsekksemmm
This document provides removal and installation procedures for various components on a machine. The components included are the battery, alternator, electric starting motor, air cleaner, muffler, and expansion tank. Detailed step-by-step instructions are provided for safely removing and installing each component, including necessary safety precautions. Illustrations supplement the written instructions to aid in the process.
Caterpillar cat th580 b telehandler service repair manualfjjskekfksmemm
This document provides removal and installation procedures for various components on a machine. The components included are the battery, alternator, electric starting motor, air cleaner, muffler, and expansion tank. Detailed step-by-step instructions are provided for safely removing and installing each component, including necessary safety precautions. Illustrations supplement the written instructions to aid in the process.
Caterpillar cat th580 b telehandler service repair manualudfjdfjjskekemm
This document contains removal and installation procedures for various components of a machine. Sections include the engine, powertrain, vehicle systems, machine components, electrical systems, and troubleshooting. Specific components covered include the battery, alternator, starter motor, air cleaner, muffler, expansion tank, radiator, and related brackets. Detailed steps are provided for draining fluids, disconnecting hoses and electrical connections, removing mounting hardware, and replacing components. Safety notices are included regarding hot or pressurized fluids, electrical hazards, and preventing accidental starting.
Caterpillar cat 951 c track loader (prefix 86j) service repair manual (86j040...ujjfjkskekmme
- The document provides instructions for disassembling and assembling starting motors for Caterpillar track loaders and excavators.
- It describes removing over a dozen individual components of 42-MT, 37-MT and 41-MT series starting motors in step-by-step detail.
- Reassembly instructions are also provided, with an emphasis on applying the proper lubricants to bushings, seals and other parts.
Caterpillar cat 315 c excavator (prefix cjc) service repair manual (cjc00001 ...fjsekdmmeed
The document provides step-by-step instructions for disassembling and assembling the travel motor of 315C and 315C L excavators. It lists 28 steps for disassembly, which include removing bolts, valves, seals, pistons, springs and other components. It then lists 25 steps for reassembly, instructing technicians to clean parts, replace seals, apply lubricants, and reinstall components in reverse order using various tools. Technicians are advised to mark parts for orientation and take precautions when working with pressurized or spring-loaded components.
Case ih mx210 tractor service repair manualdfujsejfskekem
This document is the service manual for the MX Magnum tractor. It provides a table of contents that lists all sections and publications for servicing and repairing the tractor. Safety warnings are also provided, advising technicians to take proper precautions when working on the tractor, including wearing protective equipment, relieving pressure from hydraulic lines before disconnecting, and ensuring the engine is off and the tractor is blocked before performing any maintenance.
Caterpillar cat 349 d excavator (prefix klh) service repair manual (klh00001 ...cdsaas
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar cat th580 b telehandler service repair manualfusjefjskefkksem
This document provides removal and installation procedures for various components on a machine. It includes sections on removing and installing the battery, alternator, starter motor, air cleaner, muffler, and expansion tank. Detailed steps and illustrations are provided for each procedure. Safety precautions are also provided, such as warnings about hot components, electrical shock, and handling of chemicals.
Caterpillar cat th580 b telehandler service repair manualfjjsekksemmm
This document provides removal and installation procedures for various components on a machine. The components included are the battery, alternator, electric starting motor, air cleaner, muffler, and expansion tank. Detailed step-by-step instructions are provided for safely removing and installing each component, including necessary safety precautions. Illustrations supplement the written instructions to aid in the process.
Caterpillar cat th580 b telehandler service repair manualfjjskekfksmemm
This document provides removal and installation procedures for various components on a machine. The components included are the battery, alternator, electric starting motor, air cleaner, muffler, and expansion tank. Detailed step-by-step instructions are provided for safely removing and installing each component, including necessary safety precautions. Illustrations supplement the written instructions to aid in the process.
New holland we190 b wheeled excavator service repair manualfisejfjsekfksem
This document is a service manual for Wheeled Excavators models WE170B and WE190B. It contains instructions for repair and maintenance work that must be carried out by qualified personnel using the specified procedures and tools. The manufacturer will not be responsible for damages caused by using unapproved parts or failing to follow the proper procedures. The manual is divided into sections covering the engine, transmission, hydraulic and electrical systems, frames, steering, wheels, cab controls and more. It provides information to service these various components of the excavators.
New holland w170 c tier 4b wheel loader service repair manualfisejfjsekfksem
This service manual provides maintenance and repair instructions for the W170C Wheel Loader. It contains 19 chapters covering the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, and electrical systems. Safety must be the top priority when servicing equipment, and only authorized personnel should perform repairs. Personal protective equipment should be worn, and all safety messages and instructions must be followed carefully.
New holland w70 btc wheel loader service repair manualfisejfjsekfksem
This document provides safety instructions and technical specifications for a repair manual. It outlines general safety precautions for working on equipment, including stopping the engine and relieving hydraulic pressure before removing parts. Emergency procedures and required safety equipment are also described. Technical specifications and contact information are provided for questions.
New holland tl100 a tractor service repair manualfisejfjsekfksem
This document is a service manual for tractor models TL70A through TL100A. It contains sections on general guidelines, the engine, clutch, transmissions, and other systems. Each section provides specifications, views of components, troubleshooting information, and procedures for removal, installation, overhaul, and adjustment of parts.
New holland td5050 tractor service repair manualfisejfjsekfksem
This document is a service manual for TD series tractor models TD5010 through TD5050. It contains sections covering general information, the engine, clutch, gearbox, transmission, brakes, hydraulics, steering, axles, auxiliary equipment, electrical systems, and the cab. Each section provides specifications, diagrams, troubleshooting information, removal and installation instructions, and repair procedures for the various systems. Safety warnings are provided, noting that maintenance and repair should only be performed by trained technicians using the proper tools and following the instructions carefully.
New holland t8030 tractor service repair manualfisejfjsekfksem
This document provides a service manual for tractor models T8010 through T8050. It describes the primary hydraulic power system, including the three hydraulic pumps that are driven by the transmission. A pressure and flow compensating piston pump supplies hydraulic flow to priority valves and then to steering, remote valves, and the three point hitch. A dual gear pump has front and rear sections, with the front supplying regulated pressure and the rear providing charge flow to the piston pump. An optional high flow piston pump is also described that provides increased hydraulic flow.
New holland t6060 tractor service repair manualfisejfjsekfksem
The document is a service manual that covers hydraulic, pneumatic, electrical, and electronic systems for tractor models T6010 through T6070. It contains sections on primary and secondary hydraulic power systems, hydraulic command systems, electrical power systems, electronic systems, fault codes, engines, transmissions, axles, brakes, frames, cabs, hitches, and more. Each section contains technical data, functional descriptions, diagnostics, and service procedures.
New holland t3030 tractor service repair manualfisejfjsekfksem
This document is a service manual for T3010, T3020, T3030, and T3040 tractor models. It contains sections covering general guidelines, the engine, clutch, transmissions, front and rear mechanical transmissions, and other systems. The manual provides specifications, diagrams, troubleshooting information, removal and installation instructions, and procedures for disassembly, assembly, overhaul and adjustment of components.
New holland t9.480 stage iv tractor service repair manualfisejfjsekfksem
The document outlines various safety rules for operating agricultural equipment, including staying off slopes too steep for safe operation, not exceeding speed ratings, not driving under the influence, ensuring towed loads do not exceed tractor weight limits, and only hitching to the drawbar or using the three-point hitch as intended to avoid rear upset. Personal safety precautions are emphasized such as wearing appropriate protective equipment and not allowing others to ride on equipment. Modifications to equipment could increase debris accumulation risks.
New holland t9.435 tractor service repair manualfisejfjsekfksem
This document is a service manual that provides information on servicing various tractor models including the T9.435, T9.480, T9.530, T9.565, T9.600, T9.645, and T9.700. It contains sections on the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety information is provided at the beginning regarding servicing equipment. Torque specifications are also included for normal assembly and hydraulics.
New holland t8.410 smart trax powershift transmission (pst) tractor service r...fisejfjsekfksem
This service manual provides information for servicing the engines, transmissions, axles, hydraulics, electrical systems, and other components of T8 tractor models 320-410 with Powershift transmissions. The manual includes specifications, maintenance procedures, and troubleshooting information to assist technicians with repairs and maintenance. Sections cover the engine and its systems, transmission, axles, hydraulics, electrical systems, cab, and other components.
New holland e145 c evo crawler excavator standard w blade version (tier 3) se...fisejfjsekfksem
This document provides a 17 step process to remove an engine from an E145C EVO crawler excavator. The steps include removing the battery cable, counterweight, muffler, pump, fan shroud, fan guard, radiator hoses, connector brackets, connectors, terminal cap, wirings, lines from the compressor, heater hoses, and engine oil remote hoses. Caps and plugs are installed on disconnected parts to prevent entry of water, dust or dirt. The engine and disconnected parts are cleaned before removal to prevent scratches and dirt accumulation.
New holland e17 c mini excavator service repair manualfisejfjsekfksem
The document provides a service manual for removing the engine from a mini excavator. It lists 29 detailed steps for disconnecting all electrical connections, hoses, brackets, and bolts to fully separate the engine from the excavator. Safety warnings are provided throughout regarding hazards such as escaping fluids, heavy lifting, burns, and electrical shocks.
New holland e10 sr mini crawler excavator service repair manualfisejfjsekfksem
Here are the key safety precautions for disassembling and assembling hydraulic equipment from the document:
- Release hydraulic pressure and drain oil from pipes before disconnecting them. Apply plugs to pipe ends.
- Do not disassemble, reassemble or modify hydraulic equipment without permission from the manufacturer. Have qualified personnel perform any necessary work.
- Provide matching marks for reassembly. Read manuals and determine if you can perform the work. Use any required special jigs or tools.
- Inspect disassembled parts for issues like seizure, interference or wear. Measure and record wear and clearances. Repair or replace problematic parts.
- Clean parts thoroughly before reassembly. Always replace removed O-rings
Hyster k005 (h3.50 xm europe) forklift service repair manualfisejfjsekfksem
This document provides repair instructions for various components of a forklift, including the counterweight, hood, overhead guard, LED lights, operator restraint system, and radiator. The counterweight can be removed using lifting eyebolts and a lifting device. Hood and overhead guard removal involves disconnecting mounting hardware. LED light assemblies must be replaced as units rather than repaired. The operator restraint system, including the seat belt and hood latch, must be correctly adjusted and secured. Radiator removal requires draining coolant and disconnecting hoses and mounts.
This document provides repair instructions for various components of a forklift, including the counterweight, hood, overhead guard, LED lights, operator restraint system, and radiator. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant, disconnect hoses, and remove/install the radiator while adding coolant back to the system. Safety warnings are provided throughout regarding stability of the forklift when components that shift the center of gravity are removed.
Hyster f007 h9.00 xm forklift service repair manualfisejfjsekfksem
The document provides instructions for repairing the service frame, counterweight, fenders, hood, hydraulic tank, and other parts of a lift truck. It describes removing and installing the counterweight, fenders, and hydraulic tank. It also details cleaning and repairing the hydraulic tank, including procedures for small leaks, large leaks, and cleaning the tank using steam or chemical solutions. Welding repairs require disconnecting electronics to avoid damage.
Hyster f019 (h360 hd ec) forklift service repair manualfisejfjsekfksem
This document provides repair procedures for a differential assembly. It describes the components of a typical differential, including the housing, ring and pinion gear set, and differential assembly. It provides steps to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. It also describes how to disassemble the differential and ring gear assembly and disassemble the drive pinion and pinion carrier. The document includes warnings and cautions for safe repair.
Hyster f007 h8.00 xm forklift service repair manualfisejfjsekfksem
This document provides instructions for repairing various components of lift trucks, including the counterweight, fenders, hood, hydraulic tank, and other parts. The counterweight and fenders are very heavy and require lifting equipment to remove and install safely. Welding should be done carefully to avoid damaging electronic control modules. Detailed steps are provided for removing, inspecting, and reinstalling each part. Safety warnings are included throughout regarding the heavy weights involved.
Hyster d010 (s35 xm) forklift service repair manualfisejfjsekfksem
The document provides an overview of the components and operation of a single-speed powershift transmission, including:
1) The transmission contains forward and reverse clutch assemblies, a torque converter, transmission pump, control valve, and differential assembly to transfer power from the engine to the wheels.
2) The torque converter uses fluid coupling between an impeller and turbine to transfer power from the engine to the transmission, and can multiply engine torque through a stator clutch mechanism.
3) The forward and reverse clutch assemblies use hydraulic pressure to engage friction discs and transfer power between the input shaft and either the forward or reverse gears to select transmission direction.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
New holland we190 b wheeled excavator service repair manualfisejfjsekfksem
This document is a service manual for Wheeled Excavators models WE170B and WE190B. It contains instructions for repair and maintenance work that must be carried out by qualified personnel using the specified procedures and tools. The manufacturer will not be responsible for damages caused by using unapproved parts or failing to follow the proper procedures. The manual is divided into sections covering the engine, transmission, hydraulic and electrical systems, frames, steering, wheels, cab controls and more. It provides information to service these various components of the excavators.
New holland w170 c tier 4b wheel loader service repair manualfisejfjsekfksem
This service manual provides maintenance and repair instructions for the W170C Wheel Loader. It contains 19 chapters covering the engine, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, and electrical systems. Safety must be the top priority when servicing equipment, and only authorized personnel should perform repairs. Personal protective equipment should be worn, and all safety messages and instructions must be followed carefully.
New holland w70 btc wheel loader service repair manualfisejfjsekfksem
This document provides safety instructions and technical specifications for a repair manual. It outlines general safety precautions for working on equipment, including stopping the engine and relieving hydraulic pressure before removing parts. Emergency procedures and required safety equipment are also described. Technical specifications and contact information are provided for questions.
New holland tl100 a tractor service repair manualfisejfjsekfksem
This document is a service manual for tractor models TL70A through TL100A. It contains sections on general guidelines, the engine, clutch, transmissions, and other systems. Each section provides specifications, views of components, troubleshooting information, and procedures for removal, installation, overhaul, and adjustment of parts.
New holland td5050 tractor service repair manualfisejfjsekfksem
This document is a service manual for TD series tractor models TD5010 through TD5050. It contains sections covering general information, the engine, clutch, gearbox, transmission, brakes, hydraulics, steering, axles, auxiliary equipment, electrical systems, and the cab. Each section provides specifications, diagrams, troubleshooting information, removal and installation instructions, and repair procedures for the various systems. Safety warnings are provided, noting that maintenance and repair should only be performed by trained technicians using the proper tools and following the instructions carefully.
New holland t8030 tractor service repair manualfisejfjsekfksem
This document provides a service manual for tractor models T8010 through T8050. It describes the primary hydraulic power system, including the three hydraulic pumps that are driven by the transmission. A pressure and flow compensating piston pump supplies hydraulic flow to priority valves and then to steering, remote valves, and the three point hitch. A dual gear pump has front and rear sections, with the front supplying regulated pressure and the rear providing charge flow to the piston pump. An optional high flow piston pump is also described that provides increased hydraulic flow.
New holland t6060 tractor service repair manualfisejfjsekfksem
The document is a service manual that covers hydraulic, pneumatic, electrical, and electronic systems for tractor models T6010 through T6070. It contains sections on primary and secondary hydraulic power systems, hydraulic command systems, electrical power systems, electronic systems, fault codes, engines, transmissions, axles, brakes, frames, cabs, hitches, and more. Each section contains technical data, functional descriptions, diagnostics, and service procedures.
New holland t3030 tractor service repair manualfisejfjsekfksem
This document is a service manual for T3010, T3020, T3030, and T3040 tractor models. It contains sections covering general guidelines, the engine, clutch, transmissions, front and rear mechanical transmissions, and other systems. The manual provides specifications, diagrams, troubleshooting information, removal and installation instructions, and procedures for disassembly, assembly, overhaul and adjustment of components.
New holland t9.480 stage iv tractor service repair manualfisejfjsekfksem
The document outlines various safety rules for operating agricultural equipment, including staying off slopes too steep for safe operation, not exceeding speed ratings, not driving under the influence, ensuring towed loads do not exceed tractor weight limits, and only hitching to the drawbar or using the three-point hitch as intended to avoid rear upset. Personal safety precautions are emphasized such as wearing appropriate protective equipment and not allowing others to ride on equipment. Modifications to equipment could increase debris accumulation risks.
New holland t9.435 tractor service repair manualfisejfjsekfksem
This document is a service manual that provides information on servicing various tractor models including the T9.435, T9.480, T9.530, T9.565, T9.600, T9.645, and T9.700. It contains sections on the engine, transmission, axles, brakes, hydraulics, electrical systems, and other components. Safety information is provided at the beginning regarding servicing equipment. Torque specifications are also included for normal assembly and hydraulics.
New holland t8.410 smart trax powershift transmission (pst) tractor service r...fisejfjsekfksem
This service manual provides information for servicing the engines, transmissions, axles, hydraulics, electrical systems, and other components of T8 tractor models 320-410 with Powershift transmissions. The manual includes specifications, maintenance procedures, and troubleshooting information to assist technicians with repairs and maintenance. Sections cover the engine and its systems, transmission, axles, hydraulics, electrical systems, cab, and other components.
New holland e145 c evo crawler excavator standard w blade version (tier 3) se...fisejfjsekfksem
This document provides a 17 step process to remove an engine from an E145C EVO crawler excavator. The steps include removing the battery cable, counterweight, muffler, pump, fan shroud, fan guard, radiator hoses, connector brackets, connectors, terminal cap, wirings, lines from the compressor, heater hoses, and engine oil remote hoses. Caps and plugs are installed on disconnected parts to prevent entry of water, dust or dirt. The engine and disconnected parts are cleaned before removal to prevent scratches and dirt accumulation.
New holland e17 c mini excavator service repair manualfisejfjsekfksem
The document provides a service manual for removing the engine from a mini excavator. It lists 29 detailed steps for disconnecting all electrical connections, hoses, brackets, and bolts to fully separate the engine from the excavator. Safety warnings are provided throughout regarding hazards such as escaping fluids, heavy lifting, burns, and electrical shocks.
New holland e10 sr mini crawler excavator service repair manualfisejfjsekfksem
Here are the key safety precautions for disassembling and assembling hydraulic equipment from the document:
- Release hydraulic pressure and drain oil from pipes before disconnecting them. Apply plugs to pipe ends.
- Do not disassemble, reassemble or modify hydraulic equipment without permission from the manufacturer. Have qualified personnel perform any necessary work.
- Provide matching marks for reassembly. Read manuals and determine if you can perform the work. Use any required special jigs or tools.
- Inspect disassembled parts for issues like seizure, interference or wear. Measure and record wear and clearances. Repair or replace problematic parts.
- Clean parts thoroughly before reassembly. Always replace removed O-rings
Hyster k005 (h3.50 xm europe) forklift service repair manualfisejfjsekfksem
This document provides repair instructions for various components of a forklift, including the counterweight, hood, overhead guard, LED lights, operator restraint system, and radiator. The counterweight can be removed using lifting eyebolts and a lifting device. Hood and overhead guard removal involves disconnecting mounting hardware. LED light assemblies must be replaced as units rather than repaired. The operator restraint system, including the seat belt and hood latch, must be correctly adjusted and secured. Radiator removal requires draining coolant and disconnecting hoses and mounts.
This document provides repair instructions for various components of a forklift, including the counterweight, hood, overhead guard, LED lights, operator restraint system, and radiator. The counterweight repair section describes how to safely remove and install the counterweight using lifting eyebolts and a lifting device. The radiator repair section explains how to drain the coolant, disconnect hoses, and remove/install the radiator while adding coolant back to the system. Safety warnings are provided throughout regarding stability of the forklift when components that shift the center of gravity are removed.
Hyster f007 h9.00 xm forklift service repair manualfisejfjsekfksem
The document provides instructions for repairing the service frame, counterweight, fenders, hood, hydraulic tank, and other parts of a lift truck. It describes removing and installing the counterweight, fenders, and hydraulic tank. It also details cleaning and repairing the hydraulic tank, including procedures for small leaks, large leaks, and cleaning the tank using steam or chemical solutions. Welding repairs require disconnecting electronics to avoid damage.
Hyster f019 (h360 hd ec) forklift service repair manualfisejfjsekfksem
This document provides repair procedures for a differential assembly. It describes the components of a typical differential, including the housing, ring and pinion gear set, and differential assembly. It provides steps to remove the differential carrier from the axle housing, remove the differential and ring gear from the carrier, and remove the drive pinion and pinion carrier from the carrier. It also describes how to disassemble the differential and ring gear assembly and disassemble the drive pinion and pinion carrier. The document includes warnings and cautions for safe repair.
Hyster f007 h8.00 xm forklift service repair manualfisejfjsekfksem
This document provides instructions for repairing various components of lift trucks, including the counterweight, fenders, hood, hydraulic tank, and other parts. The counterweight and fenders are very heavy and require lifting equipment to remove and install safely. Welding should be done carefully to avoid damaging electronic control modules. Detailed steps are provided for removing, inspecting, and reinstalling each part. Safety warnings are included throughout regarding the heavy weights involved.
Hyster d010 (s35 xm) forklift service repair manualfisejfjsekfksem
The document provides an overview of the components and operation of a single-speed powershift transmission, including:
1) The transmission contains forward and reverse clutch assemblies, a torque converter, transmission pump, control valve, and differential assembly to transfer power from the engine to the wheels.
2) The torque converter uses fluid coupling between an impeller and turbine to transfer power from the engine to the transmission, and can multiply engine torque through a stator clutch mechanism.
3) The forward and reverse clutch assemblies use hydraulic pressure to engage friction discs and transfer power between the input shaft and either the forward or reverse gears to select transmission direction.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker Jamieson
Caterpillar cat th360 b and th560b telehandler service repair manual sn tbh00100 and after
1. Section Title Manual No.
Service Manual Contents 31200265
Torque Specifications 31200268
Engine
Disassembly & Assembly Engine Supplement 31200299
Power Train
Systems Operation, Testing & Adjusting Power Train 31200270
Disassembly & Assembly Power Train 31200300
Vehicle Systems
Schematic Hydraulic System 31200304
Systems Operation, Testing & Adjusting Hydraulic System 31200302
Systems Operation, Testing & Adjusting Steering System 31200273
Systems Operation, Testing & Adjusting Brake System 31200274
Machine Components Specs Machine Systems 31200306
Disassembly & Assembly Machine Systems 31200308
Electrical Systems
Schematic - TH360B Electrical System 31200310
Schematic - TH560B Electrical System 31200311
Machine Troubleshooting Hydrostatic Transmission
Electronic Control System
31200279
Systems Operation, Testing & Adjusting LSI System 31200280
Systems Operation, Testing & Adjusting Monitoring System 31200281
TH360B & TH560B
Telehandler Service Manual
S/N TBH00100 & After
S/N TBP00100 & After
31200264
31200265 A
2. 31200299 3
Disassembly and Assembly Section
Disassembly and
Assembly Section
Battery - Remove and Install
Removal Procedure
Start By:
a. If equipped, turn the battery disconnect switch to the OFF
position. Refer to Operation and Maintenance Manual,
"Battery Disconnect Switch (if equipped) ".
Batteries give off flammable fumes that can
explode resulting in personal injury.
Prevent sparks near the batteries. They could
cause vapors to explode. Do not allow the jump
start cable ends to contact each other or the
machine.
Do not smoke when checking battery electrolyte
levels.
Electrolyte is an acid and can cause personal
injury if it contacts skin or eyes.
Always wear eye protection when starting a
machine with jump start cables.
Improper jump start procedures can cause an
explosion resulting in personal injury.
Always connect the positive (+) to positive (+) and
the negative (-) to negative (-).
Jump start only with an energy source with the
same voltage as the stalled machine.
Turn off all lights and accessories on the stalled
machine. Otherwise, they will operate when the
energy source is connected.
Illustration 1 g00909832
1. The following procedure shows the removal of the
front battery which is an attachment. Use the same
procedure when you are removing the rear battery.
Illustration 2 g00909220
2. Pull back the terminal cover (1) in order to
disconnect positive cable (2). Pull back the
terminal cover (3) in order to disconnect negative
cable (4).
Illustration 3 g00909235
3. Remove nuts (5), the washers and hold down
bracket (6).
Illustration 4 g00909831
4. With the aid of a second person or with the aid of
a suitable lifting device, remove battery (7). The
weight of the battery is approximately 25 kg (55 lb).
Remove studs (8).
3. 4 31200299
Disassembly and Assembly Section
Installation Procedure
Illustration 5 g00909832
1. The following procedure shows the installation of
the front battery which is an attachment. Use the
same procedure when you are installing the rear
battery.
Illustration 6 g00909831
2. Install studs (8). With the aid of a second person
or with the aid of a suitable lifting device, install
battery (7). The weight of the battery is
approximately 25 kg (55 lb).
Illustration 7 g00909235
3. Install hold down bracket (6), nuts (5), and the
washers.
Illustration 8 g00909220
4. Connect positive cable (2) and slide terminal cover
(1) into position. Connect Negative cable (4) and
slide terminal cover (3) into position.
End By:
a. If equipped, turn the battery disconnect switch to the ON
position. Refer to Operation and Maintenance Manual,
"Battery Disconnect Switch (if equipped)".
Alternator - Remove and Install
Removal Procedure
Start By:
a. Turn the battery disconnect switch to the OFF position.
Refer to Operation and Maintenance Manual, "Battery
Disconnect Switch (if equipped)". If the machine is not
equipped with a battery disconnect switch, disconnect
the battery cables from the battery and insulate the
battery clamps.
1. Put identification marks on all wires for installation
purposes.
Illustration 9 g00908444
2. Remove belt (1) from alternator (2). Refer to
Operation and maintenance Manual, "Belts -
Inspect/Adjust/Replace".
3. Disconnect wires (3) and positive cable (4).
4. Remove bolt (5), the washer, nut (6), bolt (7) and
the washers before removing alternator (2) from
the machine.
4. 31200299 5
Disassembly and Assembly Section
Installation Procedure
1. Clean all parts and inspect all parts. If any parts are
worn or damaged, use new Caterpillar parts for
replacement.
Illustration 10 g00908444
2. Position alternator (2) onto the machine. Install
bolt (7), nut (6) and washers. Install bolt (5) and
the washer.
3. Connect wires (3) and positive cable (4) to
alternator (2).
4. Install belt (1) from alternator (2). Refer to
Operation and maintenance Manual, "Belts -
Inspect/Adjust/Replace".
End By:
a. Turn the battery disconnect switch to the ON position.
Refer to Operation and Maintenance Manual, "Battery
Disconnect Switch (if equipped)". If the machine is not
equipped with a battery disconnect switch and the
battery was disconnected, remove the insulation from
the battery clamps and install the battery cables onto the
battery.
Electric Starting Motor -Remove
and Install
Removal Procedure
Accidental machine starting can cause injury or
death to personnel working on the machine.
To avoid accidental machine starting, turn the battery
disconnect switch to the OFF position and remove
the key. If the machine is not equipped with a battery
disconnect switch, disconnect the battery cables
from the battery and tape the battery clamps.
Place a do not operate tag at the battery disconnect
switch location to inform personnel that the
machine is being worked on.
1. Put identification marks on all wires for installation
purposes.
Illustration 11 g00908447
2. Disconnect positive cable (2) from starter motor (1).
Lift the plastic cap (not shown) in order to access
screw (3) and disconnect wire (4).
Illustration 12 g00908460
3. Remove bolt (5) in order to disconnect ground
cable (6).
4. Remove bolts (7) and remove starter motor (1)
from the engine.
Installation Procedure
1. Clean all parts and inspect all parts. If any parts are
worn or damaged, use new Caterpillar parts for
replacement.
5. 6 31200299
Disassembly and Assembly Section
Illustration 13 g00908460
2. Position starter motor (1) onto the engine and
install bolts (7).
3. Position ground cable (6) and install bolt (5).
Illustration 14 g00908447
4. Install screw (3) in order to connect wire (4). Close
the plastic cap (not shown). Connect positive cable
(2) to starter motor (1).
End By:
a. Turn the battery disconnect switch to the ON position.
Refer to Operation and Maintenance Manual, "Battery
Disconnect Switch (if equipped)". If the machine is not
equipped with a battery disconnect switch and the
battery was disconnected, remove the insulation from
the battery clamps and install the battery cables onto the
battery.
Air Cleaner - Remove
Removal Procedure
Illustration 15 g00909117
1. Disconnect inlet duct (2) from air cleaner assembly
(1).
Illustration 16 g00909118
2. Remove hose clamp (3) and disconnect inlet hose
(4) from air cleaner assembly (1).
Illustration 17 g00909119
3. Disconnect hose (5) from air cleaner assembly (1).
6. 31200299 7
Disassembly and Assembly Section
Illustration 18 g00909120
Illustration 19 g00909121
4. Remove nuts (6), bolts (7) and the washers
before removing air cleaner assembly (1) from the
engine.
Air Cleaner - Install
Installation Procedure
1. Clean all parts and inspect all parts. If any parts are
worn or damaged, use new Caterpillar parts for
replacement.
Illustration 20 g00909122
Illustration 21 g00909123
2. Position air cleaner assembly (1) on the engine and
install bolts (7), nuts (6) and the washers.
Illustration 22 g00909124
3. Connect hose (5) to air cleaner assembly (1).
Illustration 23 g00909125
4. Connect inlet hose (4) to air cleaner assembly (1)
and install hose clamp (3).
7. 8 31200299
Disassembly and Assembly Section
Illustration 24 g00909126
5. Connect inlet duct (2) to air cleaner assembly (1).
Muffler - Remove and Install
Removal Procedure
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact
skin.
Illustration 25 g00914593
1. Remove bolts (1) and the washers in order to
remove cover (2) and exhaust shield (3).
Illustration 26 g00914594
The photograph is from the top side of the muffler
2. Remove clamp (4) which connects exhaust pipe (5)
to muffler (6).
Illustration 27 g00914595
Illustration 28 g00914606
3. Remove bolts (7) and the washers before sliding
muffler (6) away from exhaust pipe (5). Remove the
muffler from the machine.
Installation Procedure
Illustration 29 g00914606
8. 31200299 9
Disassembly and Assembly Section
Illustration 30 g00914595
1. Position muffler (6) and then slide the muffler onto
exhaust pipe (5) before installing bolts (7) and the
washers.
Illustration 31 g00914594
The photograph is from the top side of the muffler.
2. Install clamp (4) which connects exhaust pipe (5) to
muffler (6).
Illustration 32 g00914593
3. Position exhaust shield (3) with cover (2) and
install bolts (1) with the washers.
Expansion Tank - Remove and
Install
Removal Procedure
At operating temperature, the engine coolant is hot
and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has
been stopped and the fill cap is cool enough to
touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid
contact with the skin and eyes to prevent personal
injury.
NOTICE
Care must be taken to ensure that fluids are contained
during performance of inspection, maintenance, testing,
adjusting and repair of the product. Be prepared to collect
the fluid with suitable containers before opening any
compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and
mandates.
1. Drain the coolant from the radiator into a suitable
container so that the level of the coolant in the
radiator is below the level of the expansion tank.
The capacity of the cooling system is
approximately 27.5 L (7.3 US gal). Refer to the
appropriate Operation and Maintenance Manual.
Illustration 33 g00914256
2. Loosen the hose clamp and disconnect hose (6)
from expansion tank (3).
3. Disconnect hose (4) from filler cap (5).
9. 10 31200299
Disassembly and Assembly Section
Illustration 34 g00914264
4. Loosen the hose clamps and disconnect hose (1)
and hose (2) from expansion tank (3).
5. Remove bolts (7) and the washers in order to
remove expansion tank (3).
Installation Procedure
Illustration 35 g00914264
1. Position expansion tank (3) and install bolts (7)
and the washers.
2. Connect hose (6) to expansion tank (3) and
tighten the hose clamp.
Illustration 36 g00914256
3. Disconnect hose (4) from filler cap (5).
4. Connect hose (1) and hose (2) to expansion tank
(3) and tighten the hose clamps.
5. Fill the cooling system. The capacity of the cooling
system is approximately 27.5 L (7.3 US gal).
Refer to the appropriate Operation and
Maintenance Manual.
Radiator - Remove
Removal Procedure
Start By:
a. Remove the access plate.
At operating temperature, the engine coolant is hot
and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has
been stopped and the fill cap is cool enough to
touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid
contact with the skin and eyes to prevent personal
injury.
NOTICE
Care must be taken to ensure that fluids are contained
during performance of inspection, maintenance, testing,
adjusting and repair of the product. Be prepared to collect
the fluid with suitable containers before opening any
compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and
mandates.
1. Put identification marks on all hoses for installation
purposes. Plug all hoses. This helps to prevent
fluid loss, and this helps to keep contaminants
from entering the system.
2. Drain the coolant from the cooling system into a
suitable container for storage or disposal. The
capacity of the cooling system is approximately
27.5 L (7.3 US gal). Refer to the appropriate
Operation and Maintenance Manual.
10. 31200299 11
Disassembly and Assembly Section
Illustration 37 g00912426
3. If equipped, release latch (1) in order to remove
condenser (2) from radiator (3). Tilt the condenser
and remove the condenser from the mounts at the
base of the radiator. Move the condenser aside.
Note: Do not disconnect the hose to the condenser.
The radiator can be removed without discharging the
refrigerant.
Illustration 38 g00912772
4. Loosen the hose clamp and disconnect hose (top)
(4) from radiator (3).
Illustration 39 g00912773
5. Loosen the hose clamp and disconnect hose
(bottom) (5) from the radiator.
Illustration 40 g00912779
6. Loosen the hose clamp and disconnect hose (6)
from radiator (3).
Illustration 41 g00912775
7. Remove bolts (7) and the washer from both sides
of shroud (8).
Illustration 42 g00912780
8. Remove bolts (9), the washers, bolt (10), the
washer and mount (11) in order to remove bracket
(12) from radiator (3) and the chassis.
11. 12 31200299
Disassembly and Assembly Section
Illustration 43 g00912781
9. Remove bolt (13), the washers, mount (14), bolt
(15) and the washer in order to remove bracket
(16) from radiator (3) and the chassis.
Illustration 44 g00912782
10. Remove bolts (17), the washers and the nuts that
secure radiator (3) to the chassis.
11. With the aid of a second person, remove radiator
(3) from the machine.
Illustration 45 g00912783
12. Remove mounts (18) from the chassis.
Radiator - Disassemble
Disassembly Procedure
Start By:
a. Remove the radiator from the machine. Refer to
Disassembly and Assembly, "Radiator - Remove".
Illustration 46 g00913571
1. Remove bolts (1) and the washers in order to
remove bracket (2) from radiator (3).
Illustration 47 g00913572
2. Remove bolts (4) and the washers in order to
remove bracket (5) from radiator (3).
Illustration 48 00913575
12. 31200299 13
Disassembly and Assembly Section
3. Remove bolts (6) and the washers in order to
remove mounting bracket (7) from radiator core
(3).
4. Remove bolts (8) and the washers in order to
remove mounting bracket (9) from radiator core
(3).
Radiator - Assemble
Assembly Procedure
Illustration 49 00913593
1. Position mounting bracket (9) onto radiator (3) and
install bolts (8) with the washers.
2. Position mounting bracket (7) onto radiator (3) and
install bolts (6) with the washers.
Illustration 50 g00913594
3. Position bracket (5) onto the front of radiator (3)
and install bolts (4) with the washers.
Illustration 51 g00913595
4. Position bracket (2) onto the front of radiator (3)
and install bolts (1) with the washers.
End By:
a. Install the radiator onto the machine. Refer to
Disassembly and Assembly, "Radiator - Install".
Radiator - Install
Installation Procedure
1. Clean all parts and inspect all parts. If any parts are
worn or damaged, use new Caterpillar parts for
replacement.
Illustration 52 g00912841
2. Install mounts (18) into the chassis.
Illustration 53 g00912843
13. 14 31200299
Disassembly and Assembly Section
3. With aid of a second person, lift radiator (3) into
position. Install bolts (17), the washers and the nuts
that secure the radiator to the chassis.
Illustration 54 g00912846
4. Install bolt (13), the washer, mount (14), bolt (15)
and the washer in order to secure bracket (16) to
radiator (3) and the chassis.
Illustration 55 g00912848
5. Install bolts (9), the washer, bolt (10), the washer
and mount (11) in order to secure bracket (12) to
radiator (3) and the chassis.
Illustration 56 g00912849
6. Install bolts (7) and the washers into both sides of
shroud (8).
Illustration 57 g00912853
7. Connect hose (6) to radiator (3) and tighten the
hose clamp.
Illustration 58 g00912861
8. Connect hose (bottom) (5) to radiator (3) and
tighten the hose clamp.
Illustration 59 g00912860
9. Connect hose (top) (4) to radiator (3) and tighten
the hose clamp.
14. 31200299 15
Disassembly and Assembly Section
Illustration 60 g00912875
10. If equipped, Install condenser (2) into the mounts
at the base of radiator (3) before you fasten latch
(1).
11. Fill the cooling system. The capacity of the cooling
system is approximately 27.5 L (7.3 US gal).
Refer to the appropriate Operation and
Maintenance Manual.
End By:
a. Install the access plate.
Fan Guard - Remove and Install
Removal Procedure
Illustration 61 g00909977
1. Remove bolts (1) and the washers in order to
remove fan guard (2) from shroud (3).
Installation Procedure
Illustration 62 g00909977
1. Position fan guard (2) on shroud (3) and install
bolts (1) and the washers.
Transmission Oil Cooler -
Remove
Removal Procedure
Start By:
a. Remove the access plate.
Personal injury can result from hydraulic oil
pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic
system after the engine has been stopped. Serious
injury can be caused if this pressure is not released
before any service is done on the hydraulic system.
Make sure all of the attachments have been
lowered, oil is cool before removing any
components or lines. Remove the oil filler cap only
when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
At operating temperature, the engine coolant is hot
and under pressure.
Steam can cause personal injury.
15. 16 31200299
Disassembly and Assembly Section
Check the coolant level only after the engine has
been stopped and the fill cap is cool enough to
touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid
contact with the skin and eyes to prevent personal
injury.
NOTICE
Care must be taken to ensure that fluids are contained
during performance of inspection, maintenance, testing,
adjusting and repair of the product. Be prepared to collect
the fluid with suitable containers before opening any
compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and
mandates.
1. Put Identification marks on all hoses for installation
purposes. Plug all hoses. This helps to prevent
fluid loss, and this helps to keep contaminants
from entering the system.
2. Drain the coolant from the cooling system into a
suitable container for storage or disposal. The
capacity of the cooling system is approximately
27.5 L (7.3 US gal). Refer to the appropriate
Operation and Maintenance Manual.
Illustration 63 g00910188
3. From the underside of the machine, loosen the
hose clamps and disconnect hoses (1) from oil
cooler (2).
4. Loosen the hose clamps and disconnect hoses
(3) from oil cooler (2).
5. Remove bolts (4) and the washer in order to
remove oil cooler (2) from the machine.
Transmission Oil Cooler -Install
Installation Procedure
Oil Cooler (High Ambient Temperature
Cooling Arrangement)
Note: The following procedure will give additional
information that is required to install an oil cooler for the
high ambient temperature cooling arrangement.
Remove Components
Illustration 64 g00987113
1. Loosen the hose clamp and remove hose (1) from
radiator (2).
2. Remove all hose clips and any cable straps which
secure hose (3).
3. Loosen the hose clamp and disconnect hose (3)
from water pump (4).
4. Loosen the hose clamp and disconnect hose (3)
from expansion tank (5) before removing the hose
from the machine.
Install Components
Illustration 65 g00987125
1. The following steps show the location of all hoses to
be installed with the high ambient temperature
cooling arrangement. Refer to Parts Manual, "Lines
16. 31200299 17
Disassembly and Assembly Section
Gp - Coolant" for the part numbers for all
components.
2. Connect a new hose (3) to expansion tank (5) and
tighten the hose clamp.
3. Connect hose (3) to water pump (4) and tighten
the hose clamp.
4. Install all hose clips and any cable straps which
secure hose (3).
Note: A new hose clamp (6) is installed as part of the
installation procedure for the oil cooler. Refer to
Disassembly and Assembly, "Transmission Oil Cooler -
Install".
5. Connect a new hose (1) to radiator (2).
Note: A new hose clamp (6) is installed as part of the
installation procedure for the oil cooler. Refer to
Disassembly and Assembly, "Transmission Oil Cooler -
Install".
Transmission Oil Cooler
1. Clean all parts and inspect all parts. If any parts are
worn or damaged, use new Caterpillar parts for
replacement.
Illustration 66 g00910194
2. At the underside of the machine, position oil cooler
(2) and install bolts (4) and the washers.
3. Connect hoses (3) and tighten the hose clamps.
4. Connect hoses (1) and tighten the hose clamps.
5. Fill the cooling system. The capacity of the cooling
system is approximately 27.5 L (7.3 US gal).
Refer to the appropriate Operation and
Maintenance Manual.
Refrigerant Condenser -
Remove and Install
Removal Procedure
Personal injury can result from contact with
refrigerant.
Contact with refrigerant can cause frost bite. Keep
face and hands away to help prevent injury.
Protective goggles must always be worn when
refrigerant lines are opened, even if the gauges
indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed.
Slowly loosen the fitting. If the system is still under
pressure, release it slowly in a well ventilated area.
Personal injury or death can result from inhaling
refrigerant through a lit cigarette.
Inhaling air conditioner refrigerant gas through a lit
cigarette or other smoking method or inhaling
fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm
or death.
Do not smoke when servicing air conditioners or
wherever refrigerant gas may be present.
Use a certified recovery and recycling cart to properly
remove the refrigerant from the air conditioning
system.
1. Recover the air conditioner refrigerant from the air
conditioner system. The correct charge is 0.8 kg
(1.8 lb).
Illustration 67 g00910214
2. Disconnect two hoses (1) from condenser (2).
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. 18 31200299
Disassembly and Assembly Section
Illustration 68 g00910954
Illustration 69 g00910955
3. Release latch assembly (3). Tilt condenser (2)
toward the front of the machine before removing the
condenser.
Installation Procedure
Illustration 70 g00945940
Illustration 71 g00910954
1. Install condenser (2) into mount (4). Tilt the
condenser toward the rear of the machine and
fasten latch assembly (3).
Illustration 72 g00910214
2. Connect two hoses (1) to condenser (2).
3. Charge the air conditioner system. The correct
charge is 0.8 kg (1.8 lb).
19. 31200299 19
Disassembly and Assembly Section
Refrigerant Compressor -
Remove and Install
Removal Procedure
Start By:
a. Recover the air conditioner refrigerant from the air
conditioner system. The correct charge is 0.8 kg
(1.8 lb).
b. Remove the air cleaner. Refer to Disassembly and
Assembly, "Air Cleaner - Remove".
c. Remove the fan drive belt. Refer to
Operation and Maintenance Manual, "Belts -
Inspect/Adjust/Replace".
Personal injury can result from contact with
refrigerant.
Contact with refrigerant can cause frost bite. Keep
face and hands away to help prevent injury.
Protective goggles must always be worn when
refrigerant lines are opened, even if the gauges
indicate the system is empty of refrigerant.
Always use precaution when a fitting is removed.
Slowly loosen the fitting. If the system is still under
pressure, release it slowly in a well ventilated area.
Personal injury or death can result from inhaling
refrigerant through a lit cigarette.
Inhaling air conditioner refrigerant gas through a lit
cigarette or other smoking method or inhaling
fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm
or death.
Do not smoke when servicing air conditioners or
wherever refrigerant gas may be present.
Use a certified recovery and recycling cart to properly
remove the refrigerant from the air conditioning
system.
1. Put identification marks on all hose, on all tubes
and on all wires for installation purposes. Plug all
hoses and tubes. This helps prevent fluid loss, and
this helps to keep contaminants from entering the
system.
Illustration 73 g00921116
2. Remove bolt (1), the washers, the nut, the lower
half of mount (2) and plate (3). This will enable
access to the rear of refrigerant compressor (4).
Illustration 74 g00921516
3. Disconnect two tubes (5) from refrigerant
compressor (4).
Illustration 75 g00921517
4. Disconnect harness (6) from refrigerant
compressor (4).
5. Remove four bolts (7) and the washers in order
to remove refrigerant compressor (4) from the
machine.
Installation Procedure
1. Clean all parts and inspect all parts. If any parts are
worn or damaged, use new Caterpillar parts for
replacement.
20. 20 31200299
Disassembly and Assembly Section
Illustration 76 g00921517
2. Position refrigerant compressor (4) onto the
machine and install four bolts (7) and the washers.
3. Connect harness (6) for refrigerant compressor
(4).
Illustration 77 g00921516
4. Connect two tubes (5) to refrigerant compressor
(4).
Illustration 78 g00921116
5. Position the lower half of mount (2) and plate (3)
before installing bolts (1), the washers and the nut.
Tighten the nut and the bolt to a torque of 775 ± 20
Nm (572 ± 15 lb ft).
End By:
a. Install the fan drive belt. Refer to Operation
and Maintenance Manual, "Belts -
Inspect/Adjust/Replace".
b. Install the air cleaner. Refer to Disassembly and
Assembly, "Air Cleaner- Install".
c. Charge the air conditioner system. The correct
charge is 0.8 kg (1.8 lb).
Engine Mount (Front) - Remove
Removal Procedure
Start By:
a. Remove the hood and the rear cover panel. Refer to
Disassembly and Assembly, "Engine Enclosure - Remove
and Install".
Personal injury or death can result from improper
lifting or blocking.
When a hoist or jack is used to lift any part or
component, stand clear of the area. Be sure the
hoist or jack has the correct capacity to lift a
component. Install blocks or stands before
performance of any work under a heavy
component.
Approximate weights of the components are
shown. Clean all surfaces where parts are to be
installed.
1. The following procedure is used to remove the
engine mount from the right side of the machine.
Use the same procedure to remove the engine
mount from the left side of the machine.
Illustration 79 g00921569
2. Remove bolt (1), the washers, the nut, the lower
half of mount (2) and washers (3).