This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves removing 28 parts from the swing drive assembly including discs, plates, pistons, gears, bearings and seals. The assembly procedure specifies installing these same parts in reverse order and includes steps for properly setting bearing preloads using torque wrenches and dial indicators. Lubricants and cleaning of parts are also emphasized to ensure proper functioning of the reassembled swing drive.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly section provides instructions for installing these parts in reverse order and specifies torque specifications and lubrication requirements. Proper cleaning and inspection of parts is emphasized before assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving tensioned springs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure lists the parts and provides instructions for installing components like bearings, seals, and gears in the proper order and orientation. Precautions are outlined regarding spring forces, bearing temperatures, lubrication, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Safety notices are included and each step includes an illustration of the part being removed or installed. Lubrication and torque specifications are provided to ensure proper assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure instructs installing these same parts in reverse order and provides specifics on lubricating and setting torque specifications for certain components. Safety notices are included throughout regarding handling parts under spring tension.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly section provides instructions for installing these parts in reverse order and specifies torque specifications and lubrication requirements. Proper cleaning and inspection of parts is emphasized before assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving tensioned springs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure lists the parts and provides instructions for installing components like bearings, seals, and gears in the proper order and orientation. Precautions are outlined regarding spring forces, bearing temperatures, lubrication, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Safety notices are included and each step includes an illustration of the part being removed or installed. Lubrication and torque specifications are provided to ensure proper assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure instructs installing these same parts in reverse order and provides specifics on lubricating and setting torque specifications for certain components. Safety notices are included throughout regarding handling parts under spring tension.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves using various tools to remove over 20 components of the swing drive including plates, discs, pistons, seals, gears, and bearings. The assembly section provides the reverse steps and specifies applying lubricant to components and setting torque specifications when reinstalling parts. Proper cleaning and inspection of parts is emphasized before and after disassembly and assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and parts and provides step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts from the swing brake assembly and swing drive housing. The assembly process is the reverse and specifies applying lubricant to bearings and setting torque specifications when tightening nuts. Proper cleaning and inspection of parts is emphasized for reassembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...jfskemsemm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to correctly reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to fully disassemble and reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive assembly, including gears, pins, seals, and bearings. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, noting that all seals and gaskets must be replaced and components lubricated before assembly. Proper torque specifications are provided for securing critical fasteners.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision and cleanliness are emphasized throughout.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents a 28 step procedure for disassembly that includes removing bolts, pins, gears, seals, and other components. The assembly section lists the same tools and presents a 17 step process for installing these components in reverse order. Precautions and specifications for properly adjusting bearing torque are also provided.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fjsekdemmd
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and using tools to properly install components like seals, bearings, and retaining rings. Precautions are given for releasing spring forces and setting proper torque specifications during assembly.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps for reassembling the swing drive components in reverse order. Precautions and special tools required are listed. Proper cleaning, lubrication, and torque specifications are emphasized throughout.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Proper cleaning and lubrication of parts is emphasized. Various specialty tools are listed that are needed to remove or install specific components while applying the proper force or torque.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Precautions and special tools required are listed. Lubrication and cleaning of parts is emphasized prior to assembly.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Proper cleaning and lubrication of parts is emphasized. Various specialty tools are listed that are required for tasks like removing retaining rings and relieving spring tension.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps to reassemble the swing drive, installing the components in reverse order and noting that all seals and gaskets must be replaced. Precise torques and procedures are specified for installing bearings and tightening nuts to properly set bearing preload. Cleanliness is stressed and lubrication of parts is required during assembly.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the various components of the swing drive. These include removing retaining rings, springs, discs, plates, seals, gears, and bearings. It then lists 21 steps for reassembling the swing drive components in reverse order. Precautions are given to relieve spring tension safely and to clean and lubricate parts properly during assembly. Required tools are listed for specific disassembly and assembly tasks.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps to reassemble the swing drive, installing the components in reverse order and noting that all seals and gaskets must be replaced. Precise torques and clear illustrations are provided to ensure correct assembly.
The document provides instructions for removing and installing final drives on a Caterpillar D6R track-type tractor. Key steps include using tools to separate the final drive from the steering clutch and main case, and removing it from the machine. Reinstallation involves placing the final drive back into position, reattaching it to surrounding components, and refilling it with oil. The instructions also describe disassembling and assembling the individual components within the final drive, such as planetary carriers and hub assemblies. Precise procedures help ensure correct bearing preloads and orientations of seals.
The document provides instructions for removing and installing final drives and the power train oil filter on a D6R track-type tractor. Key steps include using tools to remove the outer axle and final drive from the machine. The final drive must be removed to access the planetary carriers for disassembly. Instructions are also given for disassembling and assembling the planetary carriers and hubs. The power train oil filter is removed by draining oil, removing mounting bolts, and using a hoist.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix MRT) Service Repair Manual...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a Caterpillar D6R III track-type tractor. It details 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then outlines 16 steps to reassemble the final drive, providing details on cleaning, heating and cooling parts, and torquing bolts to specification. Precise positioning and installation of components like seals, shafts, and bearings is emphasized to ensure correct assembly and component function.
More Related Content
Similar to Caterpillar Cat M316C WHEELED Excavator (Prefix BDX) Service Repair Manual Instant Download.pdf
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves using various tools to remove over 20 components of the swing drive including plates, discs, pistons, seals, gears, and bearings. The assembly section provides the reverse steps and specifies applying lubricant to components and setting torque specifications when reinstalling parts. Proper cleaning and inspection of parts is emphasized before and after disassembly and assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and parts and provides step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts from the swing brake assembly and swing drive housing. The assembly process is the reverse and specifies applying lubricant to bearings and setting torque specifications when tightening nuts. Proper cleaning and inspection of parts is emphasized for reassembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...jfskemsemm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to correctly reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to fully disassemble and reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive assembly, including gears, pins, seals, and bearings. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, noting that all seals and gaskets must be replaced and components lubricated before assembly. Proper torque specifications are provided for securing critical fasteners.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision and cleanliness are emphasized throughout.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents a 28 step procedure for disassembly that includes removing bolts, pins, gears, seals, and other components. The assembly section lists the same tools and presents a 17 step process for installing these components in reverse order. Precautions and specifications for properly adjusting bearing torque are also provided.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fjsekdemmd
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and using tools to properly install components like seals, bearings, and retaining rings. Precautions are given for releasing spring forces and setting proper torque specifications during assembly.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps for reassembling the swing drive components in reverse order. Precautions and special tools required are listed. Proper cleaning, lubrication, and torque specifications are emphasized throughout.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Proper cleaning and lubrication of parts is emphasized. Various specialty tools are listed that are needed to remove or install specific components while applying the proper force or torque.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Precautions and special tools required are listed. Lubrication and cleaning of parts is emphasized prior to assembly.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Proper cleaning and lubrication of parts is emphasized. Various specialty tools are listed that are required for tasks like removing retaining rings and relieving spring tension.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps to reassemble the swing drive, installing the components in reverse order and noting that all seals and gaskets must be replaced. Precise torques and procedures are specified for installing bearings and tightening nuts to properly set bearing preload. Cleanliness is stressed and lubrication of parts is required during assembly.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the various components of the swing drive. These include removing retaining rings, springs, discs, plates, seals, gears, and bearings. It then lists 21 steps for reassembling the swing drive components in reverse order. Precautions are given to relieve spring tension safely and to clean and lubricate parts properly during assembly. Required tools are listed for specific disassembly and assembly tasks.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then provides 29 steps to reassemble the swing drive, installing the components in reverse order and noting that all seals and gaskets must be replaced. Precise torques and clear illustrations are provided to ensure correct assembly.
Similar to Caterpillar Cat M316C WHEELED Excavator (Prefix BDX) Service Repair Manual Instant Download.pdf (19)
The document provides instructions for removing and installing final drives on a Caterpillar D6R track-type tractor. Key steps include using tools to separate the final drive from the steering clutch and main case, and removing it from the machine. Reinstallation involves placing the final drive back into position, reattaching it to surrounding components, and refilling it with oil. The instructions also describe disassembling and assembling the individual components within the final drive, such as planetary carriers and hub assemblies. Precise procedures help ensure correct bearing preloads and orientations of seals.
The document provides instructions for removing and installing final drives and the power train oil filter on a D6R track-type tractor. Key steps include using tools to remove the outer axle and final drive from the machine. The final drive must be removed to access the planetary carriers for disassembly. Instructions are also given for disassembling and assembling the planetary carriers and hubs. The power train oil filter is removed by draining oil, removing mounting bolts, and using a hoist.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix MRT) Service Repair Manual...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a Caterpillar D6R III track-type tractor. It details 19 steps to disassemble the final drive, removing components like the planetary carrier, gears, seals, and hub. It then outlines 16 steps to reassemble the final drive, providing details on cleaning, heating and cooling parts, and torquing bolts to specification. Precise positioning and installation of components like seals, shafts, and bearings is emphasized to ensure correct assembly and component function.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix HCD) Service Repair Manual...8fisiodkdmm3e
This document provides instructions for disassembling and assembling the final drive components of a Caterpillar D6R III track-type tractor. The disassembly process involves using various tools to remove 19 components including planetary gears, bearings, seals, and hubs. The assembly process similarly uses tools to carefully install the components in the reverse order, taking precautions to properly set bearing preloads. Special tools and procedures are specified to correctly install lip seals, duo-cone seals, and planetary gear shafts.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix JDL) Service Repair Manual...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a D6R III track-type tractor. The disassembly procedure involves 19 steps to remove components such as the planetary carrier, gears, seals, and hub. The assembly procedure describes 14 steps including pressing components, installing seals and bearings at specified temperatures, and torquing bolts to the correct specifications. Proper cleaning, lubrication, and use of specialized tools are emphasized to correctly perform the processes.
Caterpillar Cat D6R III TRACK-TYPE TRACTOR (Prefix GJB) Service Repair Manual...8fisiodkdmm3e
The document provides disassembly and assembly instructions for the final drive of a Caterpillar D6R III track-type tractor. The disassembly process involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, seals, and hub. The assembly process describes installing these 19 components in reverse order and provides details on cleaning, lubricating, heating and pressing parts as needed. Proper installation of seals, bearings, and shafts is critical to achieve correct bearing preload.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix FDT) Service Repair Manual ...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes:
1) Removing components such as the planetary carrier, gears, shafts, and hub using various tools.
2) Inspecting parts and cleaning components thoroughly before assembly.
3) Heating parts to specific temperatures and using press tools to reinstall components like seals, bearings, and shafts in the correct order and orientation.
4) Ensuring proper alignment and torque specifications are followed during reassembly to achieve correct bearing preload.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix DAE) Service Repair Manual ...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive components of a D6R II track-type tractor. It describes 19 steps to disassemble the final drive, including removing the planetary carrier, planetary gears, hub and ring gear. It then describes 17 steps for reassembling the final drive components, including pressing planetary shafts into place and torquing bolts to specifications. Precautions are given to clean parts thoroughly and apply oil during assembly.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix AEP) Service Repair Manual ...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes in detail how to remove components such as the planetary carrier, gears, shafts, seals and bearings. Special tools are required and cleanliness is important. The assembly instructions reverse the disassembly process and include heating components, applying oil, and using presses and hoists to position parts correctly with the proper torque specifications.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BMK) Service Repair Manual ...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes in detail how to remove and install each component of the final drive system, including the planetary carrier, gears, shafts, hub, seals, and other parts. Proper cleaning and lubrication of parts is emphasized. Various tools are required to disassemble, press, and install components. The process is reversed for assembly, with components installed in the specified order and following the illustrated steps.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix BLE) Service Repair Manual ...8fisiodkdmm3e
This document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. The disassembly process involves using various tools to remove 19 components of the final drive including the planetary carrier, gears, shafts, seals, and hub. The assembly process lists 17 steps for installing these components in reverse order and notes that cleanliness and applying oil to parts is important. Tools, heating components, and pressing parts are used in the assembly process to ensure correct installation and bearing preload.
Caterpillar Cat D6R II TRACK-TYPE TRACTOR (Prefix AGM) Service Repair Manual ...8fisiodkdmm3e
The document provides instructions for disassembling and assembling the final drive of a D6R II track-type tractor. It describes:
1) Removing the final drives by taking off bolts and brackets holding the planetary carrier to the hub.
2) Dismantling internal components like planetary gears, shafts, and seals from the carrier and hub.
3) Cleaning and inspecting parts before reversing the process to assemble the final drive, making sure to apply oil and heat components as needed. Precise positioning and torque settings are required.
The document provides instructions for disassembling and assembling the steering clutch and brake of a Caterpillar D6N track-type tractor. It details 19 steps for disassembly, including removing bolts, plates, seals, springs and other components. It then lists 18 steps for reassembly, instructing technicians to clean parts, apply oil to seals, and reinstall components in reverse order. The final pages connect the steering clutch and brake back to the final drive, and instruct installing the assembled components.
The document provides instructions for removing and installing the final drive, steering planetary, and brake assembly on the right side of a D6N track-type tractor. The removal process involves detaching lifting brackets, removing bolts and nuts, and lifting the assembly out of place using the brackets. The installation is the reverse of removal, applying lubricant to bolts and tightening to the specified torque values.
Caterpillar Cat D4E TRACK TRACTOR Service Repair Manual Instant Download.pdf8fisiodkdmm3e
This document provides instructions for removing and installing an alternator, fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar D4E track-type tractor with a 3304 engine. The alternator disassembly procedure involves removing components like the pulley, fan, bearings, and stator. The assembly procedure describes cleaning and reinstalling these parts. Instructions are also given for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump, which involve disconnecting fuel lines and removing mounting bolts.
This document provides instructions for removing and disassembling the fuel injection pump housing and governor from a Caterpillar 3304B engine. The removal procedure involves disconnecting fuel lines and other components before removing mounting bolts and lifting the housing off the engine. The disassembly process then describes removing individual parts like the fuel rack, lifters, bearings, camshaft, and other components from within the housing. Precise measurements and special tools are specified to correctly disassemble and reassemble each part.
The documents provide instructions for removing and installing the fuel priming pump, removing and installing the fuel filter base, removing the fuel transfer pump, and disassembling and assembling the fuel transfer pump for a Caterpillar D5B track-type tractor. The procedures include removing bolts and hoses, checking gaskets and seals, and cleaning parts before installation to properly maintain the fuel system components. Safety notices are included to handle fluids properly and avoid contamination.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar D4E track-type tractor. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in reverse order. Safety notices recommend keeping parts clean and containing fluids to dispose of properly.
Caterpillar Cat CS-683E Vibratory Compactor (Prefix ASG) Service Repair Manua...8fisiodkdmm3e
This document provides instructions for assembling the final drive planetary of a CS-683E vibratory compactor. It describes 39 steps to install various components like retaining rings, bearings, seals, gears, pins, washers, and a brake piston. Tools and torque specifications are listed. The assembly is checked by measuring brake piston displacement which should be 1.30 ± 0.05 mm. Installation of the final drive planetary unit into the machine is also described.
The document provides instructions for removing and installing fuel system components on a Caterpillar D4E track-type tractor, including:
1) The fuel priming pump removal procedure which involves turning off the fuel supply, removing bolts and reinstalling in reverse.
2) The fuel filter base removal procedure which involves disconnecting fuel lines and removing bolts.
3) The fuel transfer pump removal procedure which involves turning off the fuel supply and removing connecting tubes and bolts.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M316C WHEELED EXCAVATOR BDX
Configuration: M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M316C Excavator Machine Systems
Media Number -RENR6992-04 Publication Date -01/02/2009 Date Updated -20/02/2009
i03484220
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 1U-8759 Retaining Ring Pliers 1
D 5P-4758 Retaining Ring Pliers 1
E 1P-1859 Retaining Ring Pliers 1
F 1P-1855 Retaining Ring Pliers 1
G 156-7100 Puller 1
H 1P-1863 Retaining Ring Pliers 1
J
305-4538 Spanner Socket(1)
1
240-8274 Insert(2)
1
174-9465 Spanner Socket(3)
1
K 1P-0520 Driver Gp 1
(1)
Used on the part number 152-7372 Swing Drive Gp
(2)
Used on the part number 152-7372 Swing Drive Gp
(3)
Used on the part number 152-7375 Swing Drive Gp
1/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Start By:
a. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent contaminants from entering
the internal mechanism.
Illustration 1 g01027113
1. Attach Tooling (A) and a suitable lifting device to swing brake assembly (2). The weight of
swing brake assembly (2) is approximately 75 kg (165 lb).
2. Note the orientation of swing brake assembly (2) for assembly purposes.
3. Remove bolts (1). Remove swing brake assembly (2).
2/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g00906311
Illustration 3 g00909003
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Position swing brake assembly (2) in a suitable press.
5. Use Tooling (B) and a suitable press to relieve tension on retaining ring (3). Use Tooling
(C) to remove retaining ring (3).
3/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 4 g00906313
6. Remove plate (4).
Illustration 5 g00906314
7. Remove the discs and plates (5) from swing brake assembly (2).
Illustration 6 g00909004
4/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Reposition swing brake assembly (2), as shown.
9. Use Tooling (K) and a suitable press to relieve tension on retaining ring (6). Use Tooling
(D) to remove retaining ring (6) and the shim. Remove spring (6A) from swing brake
assembly (2).
Illustration 7 g00909008
10. If equipped, remove ring (7) from piston (8).
Illustration 8 g00906320
11. Use Tooling (B) and a suitable press to remove piston (8) from swing brake assembly (2).
5/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 9 g00906322
12. Remove seals (9) from the swing brake assembly.
Illustration 10 g00906324
13. Remove shaft (10) and top carrier (11) from shaft drive (12).
Illustration 11 g00906325
14. Remove bearing (13). Use Tooling (F) to remove retaining ring (14).
6/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 12 g00906327
15. Remove pins (19), gears (15), washers (18) and (17), and needle bearings (16).
Illustration 13 g00906329
16. Use Tooling (E) to remove retaining ring (20) from top carrier (11).
Illustration 14 g00906330
17. Remove sun gear (21) and washers (22) from top carrier (11).
7/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 15 g00906331
18. Use Tooling (E) to remove retaining rings (23) and bearings (24).
Illustration 16 g00909009
19. Use Tooling (G) to remove gear (25).
20. Remove needle bearings (26).
Illustration 17 g01026549
21. Use Tooling (H) to remove retaining ring (27). Remove shim (28) and carrier (27A).
8/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 18 g00909011
22. Use Tooling (G) to remove bearing race (29).
Illustration 19 g01026558
Illustration 20 g01026627
23. Position swing drive housing (33A) and pinion (33) on a suitable press.
24. Use Tooling (J) to remove nut (30). Remove ring (31) and nut (32).
Note: Support the underside of pinion (33) before the following Step is performed.
25. Use a suitable press to remove pinion (33) and bearing cone (32A).
9/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 21 g00906881
26. Remove seal (34) and lip seal (35). Use Tooling (K) to remove bearing cup (36).
Illustration 22 g01026650
27. Remove bearing cone (37) and washer (38) from pinion (33).
Illustration 23 g00906883
28. Use Tooling (K) to remove bearing cup (39).
10/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M316C WHEELED EXCAVATOR BDX
Configuration: M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M316C Excavator Machine Systems
Media Number -RENR6992-04 Publication Date -01/02/2009 Date Updated -20/02/2009
i03484340
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 1U-8759 Plier Tips 1
D 5P-4758 Retaining Ring Pliers 1
E 1P-1859 Retaining Ring Pliers 1
F 1P-1855 Retaining Ring Pliers 1
H 1P-1863 Retaining Ring Pliers 1
J
305-4538 Spanner Socket(1)
1
240-8274 Insert(2)
1
174-9465 Spanner Socket(3)
1
K 1P-0520 Driver Gp 1
L 2S-3230 Bearing Lubricant 1
M 8T-5096 Dial Indicator Gp 1
N 7H-1680 Lubrication Hand Pump 1
(1)
Used on the part number 152-7372 Swing Drive Gp
1/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. (2)
Used on the part number 152-7372 Swing Drive Gp
(3)
Used on the part number 152-7375 Swing Drive Gp
Note: Replace all O-ring seals and all gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01027198
1. Lower the temperature of bearing cup (39). Use Tooling (K) to install bearing cup (39) in
swing drive housing (33A).
Illustration 2 g00906881
2. Lower the temperature of bearing cup (36). Use Tooling (K) to install bearing cup (36).
3. Use Tooling (B) to install lip seal (35). Install seal (34). Install tooling (L) to seal (34).
2/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 3 g01026650
4. Raise the temperature of bearing cone (37). Install washer (38) and bearing cone (37) on
pinion (33).
Illustration 4 g01027078
Illustration 5 g01026558
5. The following steps should be used on machines that are equipped with the part number 152
-7372 Swing Drive Gp.
a. Apply 80 grams of Tooling (L) to the bearing cone on pinion (33). Install pinion (33)
in swing drive housing (33A).
3/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. b. Raise the temperature of bearing cone (32A). Install bearing cone (32A).
c. Install nut (32). Use Tooling (J) in order to tighten nut (32) until a slight increase in
rolling torque is obtained. Loosen nut (32) by approximately 60 degrees. Strike pinion
(33) with a soft hammer in order to release the bearing preload.
d. Determine the initial rolling torque of pinion (33). The specified rolling torque is
8 N·m (71 lb in) to 15 N·m (133 lb in). Record this value as Rolling Torque (Y).
e. As you tighten nut (32) rotate swing drive housing (33A) in order to ensure that the
bearings are seated properly. Use Tooling (J) in order to tighten nut (32) to a torque of
300 N·m (221 lb ft). Loosen nut (32) by 30 degrees to 60 degrees.
f. Install ring (31).
g. Install nut (30). Use Tooling (J) in order to tighten nut (30) to a torque of
1000 ± 100 N·m (738 ± 74 lb ft).
h. Determine the rolling torque of pinion (33). The specified rolling torque is Rolling
Torque (Y) plus 3 N·m (27 lb in) to 9 N·m (80 lb in).
6. The following steps should be used on machines that are equipped with the part number 152
-7375 Swing Drive Gp.
a. Apply 80 grams of Tooling (L) to the bearing cone on pinion (33). Install pinion (33)
in swing drive housing (33A).
b. Raise the temperature of bearing cone (32A). Install bearing cone (32A).
c. Install nut (32). Use Tooling (J) in order to tighten nut (32) until a slight increase in
rolling torque is obtained. Loosen nut (32) by approximately 60 degrees. Strike pinion
(33) with a soft hammer in order to release the bearing preload.
d. Determine the initial rolling torque of pinion (33). The specified rolling torque is
6 N·m (53 lb in) to 8 N·m (71 lb in). Record this value as Rolling Torque (Y).
e. As you tighten nut (32) rotate swing drive housing (33A) in order to ensure that the
bearings are seated properly. Use Tooling (J) in order to tighten nut (32) to a torque of
250 ± 50 N·m (184 ± 37 lb ft). Loosen nut (32) by 15 degrees to 30 degrees.
f. Install ring (31).
g. Install nut (30). Use Tooling (J) in order to tighten nut (30) to a torque of
700 ± 50 N·m (516 ± 37 lb ft).
h. Determine the rolling torque of pinion (33). The specified rolling torque is Rolling
Torque (Y) plus 2 N·m (18 lb in) to 5 N·m (44 lb in).
4/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g00907108
Illustration 7 g00907110
Illustration 8 g01027098
7. Install carrier (27A).
8. Install shim (28). Use Tooling (H) to install retaining ring (27).
9. Raise temperature of bearing race (29). Install bearing race (29) and needle bearings (26).
10. Apply Tooling (L) to the rollers. Install the rollers on bearing race (29). Install gears (25)
over bearing race (29) and the rollers.
5/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 11. Install retaining ring (23) and bearing (24).
Illustration 9 g00906330
12. Install washers (22) and sun gear (21) onto top carrier (11).
Illustration 10 g00906329
13. Use Tooling (E) to install retaining ring (20) onto top carrier (11).
Illustration 11 g00906327
14. Install needle bearings (16), washers (17) and (18), gears (15), and pins (19).
6/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 12 g00906325
15. Use Tooling (F) to install retaining ring (14). Install bearing (13).
Illustration 13 g00906324
16. Install top carrier (11) and shaft (10) in shaft drive (12).
Illustration 14 g00906322
17. Install seals (9) in the swing brake assembly.
7/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 15 g00909400
18. Use Tooling (B) to install piston (8) in swing brake assembly (2).
Illustration 16 g00906319
19. If equipped, install ring (7).
Illustration 17 g00909004
8/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (6A) and the shim.
21. Use Tooling (K) and a suitable press in order to compress spring (6A). Use Tooling (D) in
order to install retaining ring (6). Rotate the opening in retaining ring (6) by approximately
180 degrees from the notch in swing brake assembly (2).
Illustration 18 g00906314
22. Install discs and plates (5) into swing brake assembly (2).
Illustration 19 g00906313
23. Install plate (4).
9/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 20 g00906311
Illustration 21 g00909003
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Use Tooling (B) and a suitable press in order to compress the spring. Use Tooling (C) to
install retaining ring (3).
10/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 22 g01822733
25. Position Tooling (M) in order to measure the travel of piston (8). Connect Tooling (N) to
Port (P). Use Tooling (N) in order to apply 3000 kPa (435 psi) at Port (P). Record the
measured travel of piston (8) as Dimension (X).
a. The recorded Dimension (X) should be 1.2 mm (0.05 inch) to 1.4 mm (0.06 inch) on
machines that are equipped with the part number 152-7372 Swing Drive Gp.
b. The recorded Dimension (X) should be 1.1 mm (0.04 inch) to 1.3 mm (0.05 inch) on
machines that are equipped with the part number 152-7375 Swing Drive Gp.
Note: Outer plate (5) is available in different thicknesses. Use the correct thickness of
plate (5) in order to obtain the correct Dimension (X).
Illustration 23 g01027113
26. Install Tooling (A) and a suitable lifting device to swing brake assembly (2). The weight of
swing brake assembly (2) is approximately 75 kg (165 lb).
27. Position swing brake assembly (2) in swing brake housing (2A).
11/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 28. Install bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 14 15:24:03 UTC+0800 2020
12/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M316C WHEELED EXCAVATOR BDX
Configuration: M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M316C Excavator Machine Systems
Media Number -RENR6992-04 Publication Date -01/02/2009 Date Updated -20/02/2009
i01912611
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 138-7575 Link Bracket 2
Illustration 1 g00996138
1. Attach Tooling (B) and a suitable lifting device to swing drive (6) .
2. Position swing drive (6). The weight of the swing drive is approximately 75 kg (165 lb).
3. Install bolts (7) .
1/3(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading