This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 27 individual parts from the swing drive housing. The assembly procedure lists 28 steps to reinstall the parts in reverse order, applying lubricant to bearings and setting torque specifications for nuts. Proper cleaning, lubrication and torque values are emphasized to correctly reassemble the swing drive.
This document provides disassembly and assembly instructions for the swing drive of an M312 excavator. The disassembly instructions involve using various tools to remove 28 individual parts from the swing drive assembly. The assembly instructions similarly involve installing the parts in reverse order and include steps to properly seat bearings and measure torque specifications. Proper cleaning, lubrication and torque values are emphasized to ensure correct reassembly.
Caterpillar cat m316 c wheeled excavator (prefix h2c) service repair manual (...udjjjskekdmdm
This document provides instructions for disassembling and assembling the rear axle of a M316C Wheeled Excavator. It lists the required tools and gives step-by-step instructions for removing components like the carrier housing, planetary gears, and brake discs. It also describes how to reassemble the components, noting specifics like torque specifications and clearances that must be achieved. The purpose is to provide technicians with a guide for servicing the rear axle of this excavator model.
Caterpillar cat m322 c wheeled excavator (prefix bdk) service repair manual (...udfjjdjkkmds
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 21 steps for assembly, providing details on installing seals, bearings, washers, and other parts in the proper order and orientation. Precautions are given for releasing spring forces and setting bearing pressures correctly. Tools required are also listed.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 d mh wheeled excavator (prefix p9m) service repair manua...udfjjdjkkmds
This document provides instructions for disassembling and assembling the swing drive of an M318D MH wheeled excavator. It lists required tools and parts and provides 28 detailed steps for disassembly, including removing retaining rings, springs, plates, discs, seals, bearings, and gears. It then lists 21 steps for reassembly, specifying how to clean parts, apply lubricant, and set bearing torque specifications. The goal is to properly disassemble, clean, inspect, replace worn parts, and reassemble the swing drive.
Caterpillar cat m318 d wheeled excavator (prefix p8l) service repair manual (...fjjsjeusekkekm
The document provides instructions for disassembling and assembling the rear axle of a M318D wheeled excavator. It lists 23 steps for disassembly, which include removing the carrier housing, planetary gears, brake discs, and hub. It then lists 28 steps for reassembly, covering installing thrust washers, planetary gears, brake discs, ring gear housing, seals, and bolts. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches. Proper torque specifications and clearance measurements are also provided.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (...fujsjefjwerkskemm
This document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of a M318D wheeled excavator. The disassembly procedure involves removing 23 separate parts including carrier housings, planetary gears, thrust washers, retaining rings, and brake discs. The assembly procedure instructs installing these 23 parts in reverse order and includes steps to measure clearances and end play to ensure proper assembly. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque multipliers.
This document provides disassembly and assembly instructions for the swing drive of an M312 excavator. The disassembly instructions involve using various tools to remove 28 individual parts from the swing drive assembly. The assembly instructions similarly involve installing the parts in reverse order and include steps to properly seat bearings and measure torque specifications. Proper cleaning, lubrication and torque values are emphasized to ensure correct reassembly.
Caterpillar cat m316 c wheeled excavator (prefix h2c) service repair manual (...udjjjskekdmdm
This document provides instructions for disassembling and assembling the rear axle of a M316C Wheeled Excavator. It lists the required tools and gives step-by-step instructions for removing components like the carrier housing, planetary gears, and brake discs. It also describes how to reassemble the components, noting specifics like torque specifications and clearances that must be achieved. The purpose is to provide technicians with a guide for servicing the rear axle of this excavator model.
Caterpillar cat m322 c wheeled excavator (prefix bdk) service repair manual (...udfjjdjkkmds
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 21 steps for assembly, providing details on installing seals, bearings, washers, and other parts in the proper order and orientation. Precautions are given for releasing spring forces and setting bearing pressures correctly. Tools required are also listed.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 d mh wheeled excavator (prefix p9m) service repair manua...udfjjdjkkmds
This document provides instructions for disassembling and assembling the swing drive of an M318D MH wheeled excavator. It lists required tools and parts and provides 28 detailed steps for disassembly, including removing retaining rings, springs, plates, discs, seals, bearings, and gears. It then lists 21 steps for reassembly, specifying how to clean parts, apply lubricant, and set bearing torque specifications. The goal is to properly disassemble, clean, inspect, replace worn parts, and reassemble the swing drive.
Caterpillar cat m318 d wheeled excavator (prefix p8l) service repair manual (...fjjsjeusekkekm
The document provides instructions for disassembling and assembling the rear axle of a M318D wheeled excavator. It lists 23 steps for disassembly, which include removing the carrier housing, planetary gears, brake discs, and hub. It then lists 28 steps for reassembly, covering installing thrust washers, planetary gears, brake discs, ring gear housing, seals, and bolts. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches. Proper torque specifications and clearance measurements are also provided.
Caterpillar cat m318 c wheeled excavator (prefix bcz) service repair manual (...udfjjdjkkmds
This document provides instructions for separating the upper frame and undercarriage frame on an M318C wheeled excavator. It lists the required tools which include electric hydraulic pumps, cylinders, stands, pins, tubes, collars, saddles, links and guide bolts. The procedure involves using the listed tools and hydraulic jacks to lift and support the frames while removing connecting components. Proper containment of fluids is noted as important during the separation process.
Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (...fujsjefjwerkskemm
This document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of a M318D wheeled excavator. The disassembly procedure involves removing 23 separate parts including carrier housings, planetary gears, thrust washers, retaining rings, and brake discs. The assembly procedure instructs installing these 23 parts in reverse order and includes steps to measure clearances and end play to ensure proper assembly. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque multipliers.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to correctly reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to fully disassemble and reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive assembly, including gears, pins, seals, and bearings. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, noting that all seals and gaskets must be replaced and components lubricated before assembly. Proper torque specifications are provided for securing critical fasteners.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision and cleanliness are emphasized throughout.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...jfskemsemm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly section provides instructions for installing these parts in reverse order and specifies torque specifications and lubrication requirements. Proper cleaning and inspection of parts is emphasized before assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving tensioned springs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure lists the parts and provides instructions for installing components like bearings, seals, and gears in the proper order and orientation. Precautions are outlined regarding spring forces, bearing temperatures, lubrication, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Safety notices are included and each step includes an illustration of the part being removed or installed. Lubrication and torque specifications are provided to ensure proper assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure instructs installing these same parts in reverse order and provides specifics on lubricating and setting torque specifications for certain components. Safety notices are included throughout regarding handling parts under spring tension.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves using various tools to remove over 20 components of the swing drive including plates, discs, pistons, seals, gears, and bearings. The assembly section provides the reverse steps and specifies applying lubricant to components and setting torque specifications when reinstalling parts. Proper cleaning and inspection of parts is emphasized before and after disassembly and assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and parts and provides step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts from the swing brake assembly and swing drive housing. The assembly process is the reverse and specifies applying lubricant to bearings and setting torque specifications when tightening nuts. Proper cleaning and inspection of parts is emphasized for reassembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents a 28 step procedure for disassembly that includes removing bolts, pins, gears, seals, and other components. The assembly section lists the same tools and presents a 17 step process for installing these components in reverse order. Precautions and specifications for properly adjusting bearing torque are also provided.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fjsekdemmd
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and using tools to properly install components like seals, bearings, and retaining rings. Precautions are given for releasing spring forces and setting proper torque specifications during assembly.
Caterpillar cat m322 c wheeled excavator (prefix bdk) service repair manual (...fjjsekkmdmes
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Proper cleaning and lubrication of parts is emphasized. Various specialty tools are listed that are needed to remove or install specific components while applying the proper force or torque.
Toyota bt reflex rre140 h high performance reach truck service repair manualjfskemsemm
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt lpe250 electric pallet truck service repair manualjfskemsemm
The document provides information about repairing and maintaining the drive unit and final gear of trucks. It includes an overview of the drive gear components and technical specifications. Procedures are described for checking the drive gear attachment and for leaks, replacing worn components like seals and bearings, and changing the gear oil. Safety precautions are noted, such as supporting the truck properly when working underneath.
More Related Content
Similar to Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (bdx02001 and up)
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to correctly reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision is required to fully disassemble and reassemble the complex swing drive system.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves using various tools to remove 28 individual parts from the swing drive assembly, including gears, pins, seals, and bearings. The assembly procedure similarly uses tools to reinstall the parts in the reverse order, noting that all seals and gaskets must be replaced and components lubricated before assembly. Proper torque specifications are provided for securing critical fasteners.
Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (...udjjjskekdmdm
This document provides instructions for disassembling and assembling the swing drive of an M316C wheeled excavator. The disassembly procedure involves 28 steps to remove over 40 individual parts from the swing drive assembly. The assembly procedure provides 23 steps and cautions to replace all seals and gaskets, apply lubricant to bearings, and set specific torque specifications when reinstalling components to properly preload the bearings. Precision and cleanliness are emphasized throughout.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...jfskemsemm
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly section provides instructions for installing these parts in reverse order and specifies torque specifications and lubrication requirements. Proper cleaning and inspection of parts is emphasized before assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving tensioned springs.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure lists the parts and provides instructions for installing components like bearings, seals, and gears in the proper order and orientation. Precautions are outlined regarding spring forces, bearing temperatures, lubrication, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Safety notices are included and each step includes an illustration of the part being removed or installed. Lubrication and torque specifications are provided to ensure proper assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts including plates, discs, pistons, seals, gears, and bearings. The assembly procedure instructs installing these same parts in reverse order and provides specifics on lubricating and setting torque specifications for certain components. Safety notices are included throughout regarding handling parts under spring tension.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents step-by-step procedures with illustrations. The disassembly process involves using various tools to remove over 20 components of the swing drive including plates, discs, pistons, seals, gears, and bearings. The assembly section provides the reverse steps and specifies applying lubricant to components and setting torque specifications when reinstalling parts. Proper cleaning and inspection of parts is emphasized before and after disassembly and assembly.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and parts and provides step-by-step procedures with illustrations. The disassembly process involves removing over 20 individual parts from the swing brake assembly and swing drive housing. The assembly process is the reverse and specifies applying lubricant to bearings and setting torque specifications when tightening nuts. Proper cleaning and inspection of parts is emphasized for reassembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fujsjfjskekmem
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and presents a 28 step procedure for disassembly that includes removing bolts, pins, gears, seals, and other components. The assembly section lists the same tools and presents a 17 step process for installing these components in reverse order. Precautions and specifications for properly adjusting bearing torque are also provided.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fhjskemme
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fjsekdemmd
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and setting proper torque specifications when reinstalling components like the pinion, nuts, rings, and seals. Precautions are given to relieve spring tension safely and set bearing preload correctly during assembly.
Caterpillar cat m318 c mh wheeled excavator (prefix beb) service repair manua...fsjjefjskkememaq
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists 28 steps for disassembly, removing components like the swing brake assembly, discs, pins, gears, and bearings. It then lists 29 steps for reassembly, providing details on cleaning parts, applying lubricant, and using tools to properly install components like seals, bearings, and retaining rings. Precautions are given for releasing spring forces and setting proper torque specifications during assembly.
Caterpillar cat m322 c wheeled excavator (prefix bdk) service repair manual (...fjjsekkmdmes
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Proper cleaning and lubrication of parts is emphasized. Various specialty tools are listed that are needed to remove or install specific components while applying the proper force or torque.
Similar to Caterpillar cat m316 c wheeled excavator (prefix bdx) service repair manual (bdx02001 and up) (20)
Toyota bt reflex rre140 h high performance reach truck service repair manualjfskemsemm
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt lpe250 electric pallet truck service repair manualjfskemsemm
The document provides information about repairing and maintaining the drive unit and final gear of trucks. It includes an overview of the drive gear components and technical specifications. Procedures are described for checking the drive gear attachment and for leaks, replacing worn components like seals and bearings, and changing the gear oil. Safety precautions are noted, such as supporting the truck properly when working underneath.
Toyota bt lpe220 electric pallet truck service repair manualjfskemsemm
The document provides information about repairing and maintaining the drive unit and final gear of trucks. It includes an overview of the drive gear components and technical specifications. Procedures are described for checking the drive gear attachment and for leaks, replacing worn components like seals and bearings, and changing the gear oil. Safety precautions are noted, such as supporting the truck properly when working underneath.
Toyota bt lpe200 electric pallet truck service repair manualjfskemsemm
The document provides information about repairing and maintaining the drive unit and final gear of trucks. It includes an overview of the drive gear components and technical specifications. Procedures are described for checking the drive gear attachment and for leaks, replacing worn components like seals and bearings, and changing the gear oil. Safety precautions are noted, such as supporting the truck properly when working underneath.
Toyota bt lep340 be electric pallet truck service repair manualjfskemsemm
The document provides information about repairing and maintaining the drive unit and final gear of trucks. It includes an overview of the drive gear components and technical specifications. Procedures are described for checking the drive gear attachment and for leaks, replacing worn parts like seals and bearings, and changing the gear oil. Safety precautions are noted such as supporting the truck properly when working underneath.
Toyota bt c3 e150r forklift service repair manualjfskemsemm
This document is a service manual that contains information for servicing three electric forklift models (C3E100R, C3E130R, C3E150R). It includes an index listing the chapters and pages, as well as chapters covering the vehicle chassis, motors/engines, transmission, brakes, steering, electrical system, and other components. The chassis chapter provides details on vehicle models, the frame number format, disassembly/reassembly procedures, terminology, and instructions for jacking and lifting the vehicle. It also includes component diagrams and instructions for removing parts like the battery cover and operator's seat.
Toyota bt c3 e130r forklift service repair manualjfskemsemm
This document is a service manual that contains information for servicing three electric forklift models (C3E100R, C3E130R, C3E150R). It includes an index listing the chapters and pages, as well as chapters covering the vehicle chassis, motors/engines, transmission, brakes, steering, electrical system, hydraulic/pneumatic system, mast group, attachments, and options. Safety and maintenance information is also included. The document provides information on vehicle exterior views, models, frame numbers, instructions for using the manual, terminology, abbreviations, units, operating tips, component removal/installation, and tightening torques.
Toyota bt c3 e100r forklift service repair manualjfskemsemm
This document is a service manual that contains information for servicing three electric forklift models (C3E100R, C3E130R, C3E150R). It includes an index listing the chapters and pages, as well as chapters covering the vehicle chassis, motors/engines, transmission, brakes, steering, electrical system, and other components. The chassis chapter provides details on vehicle models, the frame number format, disassembly/reassembly procedures, terminology, and instructions for jacking and lifting the vehicle. It also includes component diagrams, removal/installation steps for parts like the battery cover and seat, and tables with member weights and tightening torques.
Toyota 62 7 fdf30 forklift service repair manualjfskemsemm
This service manual provides instructions for maintenance and repair of Toyota 7FDF/FGF 15-35 ton forklifts. The manual includes sections covering the general information, engine, transmission, propeller shaft, differential, front and rear axles, steering, brakes, body, mast, cylinder, oil pump, oil control valve and more. It provides exploded views of components, removal and installation procedures, inspection and adjustment procedures, lubrication schedules and lists of standard torque specifications.
Toyota 62 7 fdf25 forklift service repair manualjfskemsemm
This service manual provides instructions for maintenance and repair of Toyota 7FDF/FGF 15-35 ton forklifts. The manual includes sections covering the general information, engine, transmission, propeller shaft, differential, front and rear axles, steering, brakes, body, mast, cylinder, oil pump, oil control valve and more. It provides exploded views of components, removal and installation procedures, inspection and adjustment procedures, lubrication schedules and lists of standard torque specifications.
Toyota 62 7 fdf20 forklift service repair manualjfskemsemm
This service manual provides instructions for maintenance and repair of Toyota 7FDF/FGF 15-35 ton forklifts. The manual includes sections covering the general information, engine, transmission, propeller shaft, differential, front and rear axles, steering, brakes, body, mast, cylinder, oil pump, oil control valve and more. It provides exploded views of components, removal and installation procedures, inspection and adjustment procedures, lubrication schedules and lists of standard torque specifications.
Massey ferguson mf7490 tractors parts catalogue manualjfskemsemm
This document provides a list of parts and their descriptions for Massey Ferguson 7485 and 7490 tractors. It includes 28 items related to the engine cylinder block, 54 items for the timing gear housing, and 11 items for the flywheel and flywheel housing. Each item includes the part number, quantity, description, and any relevant comments. The parts are replacements for repair and maintenance of the tractor engines.
Massey ferguson mf7485 tractors parts catalogue manualjfskemsemm
This document provides a list of parts and their descriptions for Massey Ferguson 7485 and 7490 tractors. It includes 28 items related to the engine cylinder block, 54 items for the timing gear housing, and 11 items for the flywheel and flywheel housing. Each item includes the part number, quantity, description, and any relevant comments. The parts are replacements for repair and maintenance of the tractor engines.
Massey ferguson mf7480 tractor (tier 3 sisu engine) parts catalogue manualjfskemsemm
This document provides parts information for a Massey Ferguson 7480 tractor with a Tier 3 Sisu engine. It includes lists of parts with part numbers, descriptions, and quantities needed for the engine, alternator and bracket, starter, cylinder block, timing gear housing, and crankshaft, pistons, and piston rod. Footnotes provide additional information and specifications for some parts.
Massey ferguson mf6711 r tractor (eco4 tier 2 3; br) parts catalogue manualjfskemsemm
This document contains a table of contents and parts lists for the engine and related components of a Massey Ferguson MF 6711R tractor. The table of contents lists 19 sections covering the various tractor systems. The parts lists include technical specifications and part numbers for engine assemblies, the cylinder block, timing gear cover, crankshaft and pistons, camshaft and valve mechanism, cylinder head, intake manifold, turbocharger and exhaust manifold.
The document is a table of contents and specifications for a Massey Ferguson MF 5710 tractor. It includes sections covering the engine, axles, steering, drive train, brakes, hydraulics, electrical systems, cab, chassis, wheels, implements, and accessories. Each section includes item numbers, part numbers, quantities, descriptions, and comments for repair and replacement parts.
Massey ferguson mf5710 tractor (eco3 tier3; br) parts catalogue manualjfskemsemm
This document provides a parts list and descriptions for a Massey Ferguson MF 5710 tractor engine. It includes 23 pages detailing over 150 individual engine part numbers, descriptions, and quantities. The parts cover the major engine systems and components including the cylinder block, crankshaft, camshaft, cylinder head, intake manifold, turbocharger, and exhaust manifold.
This document provides a table of contents and part lists for various systems of a Massey Ferguson MF 5709 DYNA 4 TRACTOR, including the engine, axles, steering, drivetrain, brakes, air and hydraulic systems, electrical system, cab, chassis, decals, wheels, implement systems, and accessories. It includes part numbers, quantities, descriptions and comments for components of the engine cylinder block, timing gear cover, crankshaft and pistons, camshaft and valve mechanism, cylinder head, intake manifold, and other systems.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M316C WHEELED EXCAVATOR BDX
Configuration: M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M316C Excavator Machine Systems
Media Number -RENR6992-04 Publication Date -01/02/2009 Date Updated -20/02/2009
i03484220
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 1U-8759 Retaining Ring Pliers 1
D 5P-4758 Retaining Ring Pliers 1
E 1P-1859 Retaining Ring Pliers 1
F 1P-1855 Retaining Ring Pliers 1
G 156-7100 Puller 1
H 1P-1863 Retaining Ring Pliers 1
J
305-4538 Spanner Socket(1)
1
240-8274 Insert(2)
1
174-9465 Spanner Socket(3)
1
K 1P-0520 Driver Gp 1
(1)
Used on the part number 152-7372 Swing Drive Gp
(2)
Used on the part number 152-7372 Swing Drive Gp
(3)
Used on the part number 152-7375 Swing Drive Gp
1/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Start By:
a. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent contaminants from entering
the internal mechanism.
Illustration 1 g01027113
1. Attach Tooling (A) and a suitable lifting device to swing brake assembly (2). The weight of
swing brake assembly (2) is approximately 75 kg (165 lb).
2. Note the orientation of swing brake assembly (2) for assembly purposes.
3. Remove bolts (1). Remove swing brake assembly (2).
2/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 2 g00906311
Illustration 3 g00909003
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Position swing brake assembly (2) in a suitable press.
5. Use Tooling (B) and a suitable press to relieve tension on retaining ring (3). Use Tooling
(C) to remove retaining ring (3).
3/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 4 g00906313
6. Remove plate (4).
Illustration 5 g00906314
7. Remove the discs and plates (5) from swing brake assembly (2).
Illustration 6 g00909004
4/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Reposition swing brake assembly (2), as shown.
9. Use Tooling (K) and a suitable press to relieve tension on retaining ring (6). Use Tooling
(D) to remove retaining ring (6) and the shim. Remove spring (6A) from swing brake
assembly (2).
Illustration 7 g00909008
10. If equipped, remove ring (7) from piston (8).
Illustration 8 g00906320
11. Use Tooling (B) and a suitable press to remove piston (8) from swing brake assembly (2).
5/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 9 g00906322
12. Remove seals (9) from the swing brake assembly.
Illustration 10 g00906324
13. Remove shaft (10) and top carrier (11) from shaft drive (12).
Illustration 11 g00906325
14. Remove bearing (13). Use Tooling (F) to remove retaining ring (14).
6/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 12 g00906327
15. Remove pins (19), gears (15), washers (18) and (17), and needle bearings (16).
Illustration 13 g00906329
16. Use Tooling (E) to remove retaining ring (20) from top carrier (11).
Illustration 14 g00906330
17. Remove sun gear (21) and washers (22) from top carrier (11).
7/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 15 g00906331
18. Use Tooling (E) to remove retaining rings (23) and bearings (24).
Illustration 16 g00909009
19. Use Tooling (G) to remove gear (25).
20. Remove needle bearings (26).
Illustration 17 g01026549
21. Use Tooling (H) to remove retaining ring (27). Remove shim (28) and carrier (27A).
8/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 18 g00909011
22. Use Tooling (G) to remove bearing race (29).
Illustration 19 g01026558
Illustration 20 g01026627
23. Position swing drive housing (33A) and pinion (33) on a suitable press.
24. Use Tooling (J) to remove nut (30). Remove ring (31) and nut (32).
Note: Support the underside of pinion (33) before the following Step is performed.
25. Use a suitable press to remove pinion (33) and bearing cone (32A).
9/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 21 g00906881
26. Remove seal (34) and lip seal (35). Use Tooling (K) to remove bearing cup (36).
Illustration 22 g01026650
27. Remove bearing cone (37) and washer (38) from pinion (33).
Illustration 23 g00906883
28. Use Tooling (K) to remove bearing cup (39).
10/11(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M316C WHEELED EXCAVATOR BDX
Configuration: M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M316C Excavator Machine Systems
Media Number -RENR6992-04 Publication Date -01/02/2009 Date Updated -20/02/2009
i03484340
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 1U-8759 Plier Tips 1
D 5P-4758 Retaining Ring Pliers 1
E 1P-1859 Retaining Ring Pliers 1
F 1P-1855 Retaining Ring Pliers 1
H 1P-1863 Retaining Ring Pliers 1
J
305-4538 Spanner Socket(1)
1
240-8274 Insert(2)
1
174-9465 Spanner Socket(3)
1
K 1P-0520 Driver Gp 1
L 2S-3230 Bearing Lubricant 1
M 8T-5096 Dial Indicator Gp 1
N 7H-1680 Lubrication Hand Pump 1
(1)
Used on the part number 152-7372 Swing Drive Gp
1/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. (2)
Used on the part number 152-7372 Swing Drive Gp
(3)
Used on the part number 152-7375 Swing Drive Gp
Note: Replace all O-ring seals and all gaskets. Apply a light film of "10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01027198
1. Lower the temperature of bearing cup (39). Use Tooling (K) to install bearing cup (39) in
swing drive housing (33A).
Illustration 2 g00906881
2. Lower the temperature of bearing cup (36). Use Tooling (K) to install bearing cup (36).
3. Use Tooling (B) to install lip seal (35). Install seal (34). Install tooling (L) to seal (34).
2/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 3 g01026650
4. Raise the temperature of bearing cone (37). Install washer (38) and bearing cone (37) on
pinion (33).
Illustration 4 g01027078
Illustration 5 g01026558
5. The following steps should be used on machines that are equipped with the part number 152
-7372 Swing Drive Gp.
a. Apply 80 grams of Tooling (L) to the bearing cone on pinion (33). Install pinion (33)
in swing drive housing (33A).
3/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. b. Raise the temperature of bearing cone (32A). Install bearing cone (32A).
c. Install nut (32). Use Tooling (J) in order to tighten nut (32) until a slight increase in
rolling torque is obtained. Loosen nut (32) by approximately 60 degrees. Strike pinion
(33) with a soft hammer in order to release the bearing preload.
d. Determine the initial rolling torque of pinion (33). The specified rolling torque is
8 N·m (71 lb in) to 15 N·m (133 lb in). Record this value as Rolling Torque (Y).
e. As you tighten nut (32) rotate swing drive housing (33A) in order to ensure that the
bearings are seated properly. Use Tooling (J) in order to tighten nut (32) to a torque of
300 N·m (221 lb ft). Loosen nut (32) by 30 degrees to 60 degrees.
f. Install ring (31).
g. Install nut (30). Use Tooling (J) in order to tighten nut (30) to a torque of
1000 ± 100 N·m (738 ± 74 lb ft).
h. Determine the rolling torque of pinion (33). The specified rolling torque is Rolling
Torque (Y) plus 3 N·m (27 lb in) to 9 N·m (80 lb in).
6. The following steps should be used on machines that are equipped with the part number 152
-7375 Swing Drive Gp.
a. Apply 80 grams of Tooling (L) to the bearing cone on pinion (33). Install pinion (33)
in swing drive housing (33A).
b. Raise the temperature of bearing cone (32A). Install bearing cone (32A).
c. Install nut (32). Use Tooling (J) in order to tighten nut (32) until a slight increase in
rolling torque is obtained. Loosen nut (32) by approximately 60 degrees. Strike pinion
(33) with a soft hammer in order to release the bearing preload.
d. Determine the initial rolling torque of pinion (33). The specified rolling torque is
6 N·m (53 lb in) to 8 N·m (71 lb in). Record this value as Rolling Torque (Y).
e. As you tighten nut (32) rotate swing drive housing (33A) in order to ensure that the
bearings are seated properly. Use Tooling (J) in order to tighten nut (32) to a torque of
250 ± 50 N·m (184 ± 37 lb ft). Loosen nut (32) by 15 degrees to 30 degrees.
f. Install ring (31).
g. Install nut (30). Use Tooling (J) in order to tighten nut (30) to a torque of
700 ± 50 N·m (516 ± 37 lb ft).
h. Determine the rolling torque of pinion (33). The specified rolling torque is Rolling
Torque (Y) plus 2 N·m (18 lb in) to 5 N·m (44 lb in).
4/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g00907108
Illustration 7 g00907110
Illustration 8 g01027098
7. Install carrier (27A).
8. Install shim (28). Use Tooling (H) to install retaining ring (27).
9. Raise temperature of bearing race (29). Install bearing race (29) and needle bearings (26).
10. Apply Tooling (L) to the rollers. Install the rollers on bearing race (29). Install gears (25)
over bearing race (29) and the rollers.
5/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 11. Install retaining ring (23) and bearing (24).
Illustration 9 g00906330
12. Install washers (22) and sun gear (21) onto top carrier (11).
Illustration 10 g00906329
13. Use Tooling (E) to install retaining ring (20) onto top carrier (11).
Illustration 11 g00906327
14. Install needle bearings (16), washers (17) and (18), gears (15), and pins (19).
6/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 12 g00906325
15. Use Tooling (F) to install retaining ring (14). Install bearing (13).
Illustration 13 g00906324
16. Install top carrier (11) and shaft (10) in shaft drive (12).
Illustration 14 g00906322
17. Install seals (9) in the swing brake assembly.
7/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 15 g00909400
18. Use Tooling (B) to install piston (8) in swing brake assembly (2).
Illustration 16 g00906319
19. If equipped, install ring (7).
Illustration 17 g00909004
8/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
20. Install spring (6A) and the shim.
21. Use Tooling (K) and a suitable press in order to compress spring (6A). Use Tooling (D) in
order to install retaining ring (6). Rotate the opening in retaining ring (6) by approximately
180 degrees from the notch in swing brake assembly (2).
Illustration 18 g00906314
22. Install discs and plates (5) into swing brake assembly (2).
Illustration 19 g00906313
23. Install plate (4).
9/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 20 g00906311
Illustration 21 g00909003
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Use Tooling (B) and a suitable press in order to compress the spring. Use Tooling (C) to
install retaining ring (3).
10/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 22 g01822733
25. Position Tooling (M) in order to measure the travel of piston (8). Connect Tooling (N) to
Port (P). Use Tooling (N) in order to apply 3000 kPa (435 psi) at Port (P). Record the
measured travel of piston (8) as Dimension (X).
a. The recorded Dimension (X) should be 1.2 mm (0.05 inch) to 1.4 mm (0.06 inch) on
machines that are equipped with the part number 152-7372 Swing Drive Gp.
b. The recorded Dimension (X) should be 1.1 mm (0.04 inch) to 1.3 mm (0.05 inch) on
machines that are equipped with the part number 152-7375 Swing Drive Gp.
Note: Outer plate (5) is available in different thicknesses. Use the correct thickness of
plate (5) in order to obtain the correct Dimension (X).
Illustration 23 g01027113
26. Install Tooling (A) and a suitable lifting device to swing brake assembly (2). The weight of
swing brake assembly (2) is approximately 75 kg (165 lb).
27. Position swing brake assembly (2) in swing brake housing (2A).
11/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 28. Install bolts (1).
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Apr 14 15:24:03 UTC+0800 2020
12/12(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: WHEELED EXCAVATOR
Model: M316C WHEELED EXCAVATOR BDX
Configuration: M316C Excavator BDX02001-UP (MACHINE) POWERED BY 3056E Engine
Disassembly and Assembly
M316C Excavator Machine Systems
Media Number -RENR6992-04 Publication Date -01/02/2009 Date Updated -20/02/2009
i01912611
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 138-7575 Link Bracket 2
Illustration 1 g00996138
1. Attach Tooling (B) and a suitable lifting device to swing drive (6) .
2. Position swing drive (6). The weight of the swing drive is approximately 75 kg (165 lb).
3. Install bolts (7) .
1/3(W)
w
2020/4/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...