Caterpillar Cat E240C EXCAVATOR (Prefix 2RL) Service Repair Manual (2RL00001 and up).pdf

Service Repair Manual
Models
E240C EXCAVATOR

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: E240C EXCAVATOR 2RL
Configuration: E240C, EL240C TRACK-TYPE EXCAVATORS 2RL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01981940
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
E240C, EL240C TRACK-TYPE EXCAVATORS 2RL00001-UP (MACHINE) POWE...
2019/9/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01027146
1. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1).
2. Remove bolts (2) and bolt (3) that fastens the flywheel housing to the cylinder block.
3. Remove bolts (4). Remove flywheel housing (1). The weight of flywheel housing (1) is
approximately 25 kg (55 lb).
Installation Procedure
Table 2
Required Tools
2/4
2019/9/9

A 138-7573 Link Bracket 2
B 1U-8846 Gasket Sealant 1
NOTICE
1. Apply Tooling (B) to the entire mounting face of the flywheel housing prior to installation.
2. Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of
flywheel housing (1) is approximately 25 kg (55 lb). Position flywheel housing (1) on the
cylinder block. Install bolts (4).
3. Install bolts (2) and bolt (3).
End By:
3/4
2019/9/9

a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 9 21:42:03 UTC+0800 2019
4/4
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01929931
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
NOTICE
NOTICE
containing fluids.
Cat products.
1/4
2019/9/9

1. Remove bolts (2), crankshaft vibration damper (3), and spacers from the crankshaft pulley.
Note: For information on the reusability of the vibration damper on 3114 and 3116 engines,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8220, "Specifications
for Damper Inspection 3114 and 3116 Engines".
2. Loosen the tension on water pump drive belt (1). Remove the belt from the crankshaft
pulley.
3. Remove bolts (4) and the washers.
4. Remove crankshaft pulley (5).
Note: For information on the reusability of the crankshaft pulley, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8046, "Cast Iron and Steel Pulleys".
NOTICE
2/4
2019/9/9

1. Position crankshaft pulley (5) on the crankshaft. Install bolts (4) and tighten the bolts to a
torque of 160 ± 30 N·m (118 ± 22 lb ft).
Note: For information on the reusability of the crankshaft pulley, refer to Guideline For
Reusable Parts And Salvage Operations, SEBF8046, "Cast Iron and Steel Pulleys".
2. Install water pump drive belt (1).
Note: Check the alignment marks on the rubber vibration dampers for proper alignment.
The rubber vibration damper should be replaced if the rubber vibration damper is out of
alignment. Refer to Specifications, "Vibration Damper".
3. Install spacers and crankshaft vibration damper (3). Tighten bolts (2) to a torque of
55 ± 10 N·m (40 ± 7 lb ft).
Note: For information on the reusability of the vibration damper on 3114 and 3116 engines,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8220, "Specifications
for Damper Inspection 3114 and 3116 Engines".
3/4
2019/9/9

4. Adjust the tension of water pump drive belt (1). Refer to the Specifications Module, "Belt
Tension Chart". Also, refer to the Operation and Maintenance Manual, "Belt - Inspect".
Mon Sep 9 21:42:51 UTC+0800 2019
4/4
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01982085
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
1/2
2019/9/9

1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Mon Sep 9 21:43:38 UTC+0800 2019
2/2
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01982092
Crankshaft Front Seal - Install
SMCS - 1160-012
Table 1
Required Tools
C 1U-7430 Front Seal Installer 1
NOTICE
1/2
2019/9/9

1. Use Tooling (C) to install crankshaft front seal (1).
Note: The crankshaft seal is designed to be installed dry.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Mon Sep 9 21:44:26 UTC+0800 2019
2/2
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01176651
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Note: It is not necessary to remove the vibration damper and the crankshaft pulley in order
to remove the front cover.
1. Remove bolts (1) from front cover (2).
2. Remove front cover (2) and the gasket from the front of the engine.
1/2
2019/9/9

Mon Sep 9 21:45:13 UTC+0800 2019
2/2
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01437510
Front Cover - Install
SMCS - 1166-012
NOTICE
1/2
2019/9/9

1. Install a new gasket (3) on the front cover (2) .
2. Install the gasket and front cover (2) on the front of the engine.
3. Install bolts (1) in front cover (2) .
Mon Sep 9 21:46:01 UTC+0800 2019
2/2
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01929983
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
A 1P-0520 Driver Gp 1
Start By:
a. Remove the crankshaft vibration damper. Refer to Disassembly and Assembly, "Vibration
b. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
c. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
d. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
Note: For information on reusability of the camshaft idler gear, refer to Guideline For Reusable
Parts And Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1. Place the engine at the Top Center position. The timing marks should be in line with the
crankshaft gear.
1/2
2019/9/9

2. Identify the type of idler gear on the engine. Remove bolts (1) that hold the idler gear to the
block. Remove plate (7).
3. Identify the location of timing marks (4) and (5) on the camshaft idler gear. Identify the
location of timing mark (6) on the crankshaft drive gear.
4. Remove idler shaft (3) and camshaft idler gear (2). Separate idler gear (2) from idler shaft
(3) and remove the sleeve bearing from the camshaft idler gear.
5. Use Tooling (A) and a press to remove the bearing.
Mon Sep 9 21:46:48 UTC+0800 2019
2/2
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines, IT18F
Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G Wheel Loaders
i01930002
Gear Group (Front) - Install
SMCS - 1206-012
Table 1
Required Tools
A 1P-0520 Driver Gp 1
Note: For information on reusability of the camshaft idler gear, refer to Guideline For Reusable Parts And
Salvage Operations, SEBF8045, "Timing Gears for All Engines".
1/5
2019/9/9

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Type 1
1. Use Tooling (A) and a suitable press to install the sleeve bearing in the camshaft idler gear.
2. Install the bearing sleeve to a depth of 0.40 ± 0.25 mm (0.016 ± 0.010 inch) below the front face of
the gear.
3. Place the idler shaft (3) on the cylinder block. Install bolts (1) that hold the idler shaft to the cylinder
block. Tighten the bolts to a torque of 70 ± 15 N·m (51 ± 11 lb ft).
4. Install camshaft idler gear (2) on idler shaft (3). The timing marks should face outward.
5. Align the timing marks on camshaft idler gear (2) with the timing marks on the crankshaft drive
gear.
2/5
2019/9/9

Type 2
1. Use Tooling (A) and a suitable press and install the sleeve bearing in the camshaft idler gear.
2. Install plate (4) on the back of idler shaft (3). Position idler gear assembly on the cylinder block.
Install bolts that hold the idler gear to the engine block. Tighten the bolts to a torque of 70 ± 15 N·m
(51 ± 11 lb ft).
4. Align the timing marks on camshaft idler gear (2) with the timing marks on the crankshaft drive
gear.
3/5
2019/9/9

Type 3
1. Position idler shaft (3) on the cylinder block. Install the shortest bolt in the recessed hole in idler
shaft (3). This bolt will hold the shaft in position on the cylinder block.
3. Align the timing marks on idler gear (2) with the timing marks on the camshaft drive gear.
4. Position plate (4) over the gear and install the remaining bolts (1). Tighten bolts (1) to a torque of
70 ± 15 N·m (51 ± 11 lb ft).
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
c. Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal -
Install".
d. Install the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley -Remove and Install".
Mon Sep 9 21:47:36 UTC+0800 2019
4/5
2019/9/9

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Wheel Loaders
i01944129
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the crankshaft vibration damper. Refer to Disassembly and Assembly, "Vibration
b. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
c. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
containing fluids.
Cat products.
1. Remove any external components, if equipped.
1/3
2019/9/9

2. Support the front of the engine.
3. Remove bolts (2) and remove front engine support.
4. Remove bolts (1) and belt tightener (3).
5. Remove bolts (5) that fasten front housing (4) to the cylinder block and to the engine oil
pan. Remove front housing (4). Clean the sealant from front housing (4) and the cylinder
block.
2/3
2019/9/9

Caterpillar Cat E240C EXCAVATOR (Prefix 2RL) Service Repair Manual (2RL00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat E240C EXCAVATOR (Prefix 2RL) Service Repair Manual (2RL00001 and up).pdf

Similar to Caterpillar Cat E240C EXCAVATOR (Prefix 2RL) Service Repair Manual (2RL00001 and up).pdf (9)

More from jfkksemmdmd

More from jfkksemmdmd (20)

Recently uploaded

Recently uploaded (17)

Caterpillar Cat E240C EXCAVATOR (Prefix 2RL) Service Repair Manual (2RL00001 and up).pdf