The document provides instructions for servicing idlers and the equalizer bar on a D6R track-type tractor. It describes how to remove and install idlers, including disassembling and assembling the idlers. It also describes how to remove and install the equalizer bar, and how to disassemble and assemble the equalizer bar. The procedures involve using various tools and following steps such as removing retaining components, cleaning parts, applying lubricants, and tightening to specified torques.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 140 h motor grader (prefix 5hm) service repair manual (5hm000...fusefjskekkmem
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 3306B engine. It describes:
1. Removing the vibration damper, pulley, crankshaft seal adapter, O-ring seal, and wear sleeve.
2. Installing a new O-ring seal and crankshaft seal adapter. Installing the wear sleeve and crankshaft front seal using installing tools and adhesive.
3. The document is part of a service manual for a 140H Motor Grader and provides maintenance instructions for engine components.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjsjekksemm
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat d6 h track type tractor (prefix 6cf) service repair manual (6...fdjjsekksemxs
This service manual provides instructions for servicing track-type tractors. It details the process for removing and installing track roller frames, which requires separating the track, supporting the tractor, and removing bolts and pins to detach the frame. It also describes removing and installing idlers, which involves separating the caps and blocks to take the idlers off and replacing seals before reattaching everything.
Caterpillar cat 316 e l excavator (prefix yzz) service repair manual (yzz0000...fjskekdmjekm
This document provides specifications and repair instructions for the travel motor in a 316E L excavator. It includes specifications for the travel motor guard group, travel motor and mounting group, and travel motor group. The repair instructions describe how to remove and disassemble the travel motor, including draining oil, removing hoses, bolts, seals, plates, discs, shafts and other components. Detailed illustrations accompany each step.
Caterpillar cat 330 b excavator (prefix 8sr) service repair manual (8sr00001 ...hfjsekekmmd
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat d8 k track type tractor dozer bulldozer (prefix 77v) service ...fusjejfjskeksmem
This document provides instructions for removing and installing a torque divider from a D8K track-type tractor. Key steps include:
1. Draining the transmission oil and removing connecting lines, valves, and other components to access the torque divider.
2. Using eyebolts and wire to safely remove the heavy torque divider assembly.
3. Reversing the process to reinstall the torque divider, replacing gaskets and fittings and refilling the transmission with oil.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 140 h motor grader (prefix 5hm) service repair manual (5hm000...fusefjskekkmem
This document provides instructions for removing and installing the crankshaft front seal on a Caterpillar 3306B engine. It describes:
1. Removing the vibration damper, pulley, crankshaft seal adapter, O-ring seal, and wear sleeve.
2. Installing a new O-ring seal and crankshaft seal adapter. Installing the wear sleeve and crankshaft front seal using installing tools and adhesive.
3. The document is part of a service manual for a 140H Motor Grader and provides maintenance instructions for engine components.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjsjekksemm
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat d6 h track type tractor (prefix 6cf) service repair manual (6...fdjjsekksemxs
This service manual provides instructions for servicing track-type tractors. It details the process for removing and installing track roller frames, which requires separating the track, supporting the tractor, and removing bolts and pins to detach the frame. It also describes removing and installing idlers, which involves separating the caps and blocks to take the idlers off and replacing seals before reattaching everything.
Caterpillar cat 316 e l excavator (prefix yzz) service repair manual (yzz0000...fjskekdmjekm
This document provides specifications and repair instructions for the travel motor in a 316E L excavator. It includes specifications for the travel motor guard group, travel motor and mounting group, and travel motor group. The repair instructions describe how to remove and disassemble the travel motor, including draining oil, removing hoses, bolts, seals, plates, discs, shafts and other components. Detailed illustrations accompany each step.
Caterpillar cat 330 b excavator (prefix 8sr) service repair manual (8sr00001 ...hfjsekekmmd
The document provides instructions for removing, disassembling, assembling, and installing a rocker shaft and pushrods on an excavator engine. The removal process involves taking off the valve mechanism cover and then removing six bolts and the rocker shaft assembly. Individual pushrods are also removed after being marked for identification. Disassembly of the rocker shaft requires removing retaining rings, springs, washers and rocker arms. Assembly is the reverse of disassembly and installation involves reinstalling the rocker shaft assembly and pushrods and replacing the valve mechanism cover.
Caterpillar cat d8 k track type tractor dozer bulldozer (prefix 77v) service ...fusjejfjskeksmem
This document provides instructions for removing and installing a torque divider from a D8K track-type tractor. Key steps include:
1. Draining the transmission oil and removing connecting lines, valves, and other components to access the torque divider.
2. Using eyebolts and wire to safely remove the heavy torque divider assembly.
3. Reversing the process to reinstall the torque divider, replacing gaskets and fittings and refilling the transmission with oil.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
Caterpillar cat d6 r track type tractor (prefix 1rw) service repair manual (1...fjskemedcdmme
This document provides instructions for removing and installing idlers and the equalizer bar on a Caterpillar D6R track-type tractor. The idler removal process involves separating the track, removing bolts and caps to release the idler, which weighs 143 kg. Idler disassembly requires drilling out plugs and stoppers, and removing seals and shafts. Reassembly involves cleaning, inspecting, lubricating, and pressing components back into place. Equalizer bar removal requires removing the track roller frame, pins, and bolts to release the 315 lb bar. Reinstallation positions the bar back under the tractor and replaces the pins and bolts.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...cfvdssd
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during the assembly process.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...fjskemedcdmme
The document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It involves using tools to remove the torque divider assembly from the flywheel housing. Key steps include draining oil, removing bolts, O-rings, hoses and sleeves. To install, the process is reversed, ensuring proper alignment and torque of fasteners. The document also provides instructions for disassembling and measuring clearances within the torque divider before reassembling with the correct bearing depths and torque specifications.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It describes removing the torque divider by draining oil, disconnecting hoses, and using lifting tools to remove it from the flywheel housing. It then details disassembling the torque divider by removing internal components like carriers, wheels, seals and bearings. The assembly section describes installing these components in reverse order and includes checks of critical clearances between parts.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...jfksekksmem
The document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It involves using tools to remove the torque divider assembly from the flywheel housing. Key steps include draining oil, removing bolts, O-rings, hoses and sleeves. To install, the process is reversed, ensuring proper alignment of teeth and installation of all components. The document also provides instructions for disassembling and measuring clearances within the torque divider assembly before reassembling.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...uudjjekdmme
The document provides instructions for servicing the track and track roller frames of a D6H track-type tractor. It describes removing the track roller frame by using various tools to support the tractor and remove bolts/pins connecting the frame. Reinstalling involves reversing these steps, being careful to properly align parts and fill compartments with oil. Proper safety precautions are noted such as ensuring the tractor is on level ground before working on the roller frames.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjsekksemmx
The document provides instructions for servicing the track and track roller frames of a D6H track-type tractor. It describes removing the track roller frame by using various tools to support the tractor and separate the frame from the equalizer bar and pivot shaft. Reinstalling the track roller frame involves reversing these steps and properly aligning and securing all components. Procedures for removing, inspecting, cleaning, and reinstalling idler assemblies are also outlined. The goal is to safely separate and reconnect the track components while properly positioning seals and bolts.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjskdmnenemm
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjskekrtfsmem
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...ufsjekfksmem
The document provides instructions for servicing the track and track roller frames of a D6H track-type tractor. It describes removing the track roller frame by using various tools to support the tractor and remove bolts/pins connecting the frame. Reinstalling involves reversing these steps, being careful to properly align parts and fill compartments with oil. Proper safety precautions are noted when working on sloped or unstable surfaces.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjsjfkskefmem
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
John deere 1565 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1545 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1445 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides instructions to check each component and make any necessary repairs or adjustments.
John deere 1435 front mower service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1420 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1070 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. The manual is divided into sections covering safety, general specifications, repair specifications, fuel and lubricants, engine repair, electrical systems, power train repair, steering and brakes, hydraulics, and operational testing. Safety messages in the introduction warn of hazards such as high pressure fluids, battery explosions, and working with fuels and chemicals. Technicians are advised to follow safety precautions and use recommended tools and materials for repairs.
John deere 990 compact utility tractor service repair manualfhhjsjekmdme
The technical manual provides instructions for servicing a 990 Compact Utility Tractor. It contains sections on specific systems organized by contents, specifications, component location, schematics, theory of operation, troubleshooting, diagnostics, tests and adjustments, and repair. Safety procedures are outlined, including precautions for working with batteries, high pressure lines, and following proper service procedures. The document provides guidance on safely working on and repairing the tractor.
John deere 970 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. It contains sections on general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and operation/testing. The manual instructs technicians on repair procedures, specifications, safety practices, and diagnosing routine failures. It is intended to be an on-the-job guide for experienced service technicians repairing and maintaining these tractor models.
John deere 955 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides specifications and repair/removal instructions for John Deere compact utility tractors models 655, 755, 855, 955, 756 and 856. It includes sections on the diesel engine, fuel and air systems, alternator, power train, steering/brakes, hydraulics, and other components. The document provides overview information, safety messages, lubrication recommendations, component locations, and step-by-step repair guides to assist technicians in servicing the machines.
John deere 870 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. It contains sections on general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and operation/testing. The manual instructs technicians on repair procedures, specifications, safety practices, and diagnosing routine failures. It is intended to be an on-the-job guide for experienced service technicians.
More Related Content
Similar to Caterpillar cat d6 r track type tractor (prefix 1rw) service repair manual (1rw00001 and up)
Caterpillar cat d6 r track type tractor (prefix 1rw) service repair manual (1...fjskemedcdmme
This document provides instructions for removing and installing idlers and the equalizer bar on a Caterpillar D6R track-type tractor. The idler removal process involves separating the track, removing bolts and caps to release the idler, which weighs 143 kg. Idler disassembly requires drilling out plugs and stoppers, and removing seals and shafts. Reassembly involves cleaning, inspecting, lubricating, and pressing components back into place. Equalizer bar removal requires removing the track roller frame, pins, and bolts to release the 315 lb bar. Reinstallation positions the bar back under the tractor and replaces the pins and bolts.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...cfvdssd
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during the assembly process.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...fjskemedcdmme
The document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It involves using tools to remove the torque divider assembly from the flywheel housing. Key steps include draining oil, removing bolts, O-rings, hoses and sleeves. To install, the process is reversed, ensuring proper alignment and torque of fasteners. The document also provides instructions for disassembling and measuring clearances within the torque divider before reassembling with the correct bearing depths and torque specifications.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...fujsjefjkskemm
This document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It describes removing the torque divider by draining oil, disconnecting hoses, and using lifting tools to remove it from the flywheel housing. It then details disassembling the torque divider by removing internal components like carriers, wheels, seals and bearings. The assembly section describes installing these components in reverse order and includes checks of critical clearances between parts.
Caterpillar cat d6 h track type tractor (prefix 8fc) service repair manual (8...jfksekksmem
The document provides instructions for removing and installing a torque divider from a D6H track-type tractor. It involves using tools to remove the torque divider assembly from the flywheel housing. Key steps include draining oil, removing bolts, O-rings, hoses and sleeves. To install, the process is reversed, ensuring proper alignment of teeth and installation of all components. The document also provides instructions for disassembling and measuring clearances within the torque divider assembly before reassembling.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...uudjjekdmme
The document provides instructions for servicing the track and track roller frames of a D6H track-type tractor. It describes removing the track roller frame by using various tools to support the tractor and remove bolts/pins connecting the frame. Reinstalling involves reversing these steps, being careful to properly align parts and fill compartments with oil. Proper safety precautions are noted such as ensuring the tractor is on level ground before working on the roller frames.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjsekksemmx
The document provides instructions for servicing the track and track roller frames of a D6H track-type tractor. It describes removing the track roller frame by using various tools to support the tractor and separate the frame from the equalizer bar and pivot shaft. Reinstalling the track roller frame involves reversing these steps and properly aligning and securing all components. Procedures for removing, inspecting, cleaning, and reinstalling idler assemblies are also outlined. The goal is to safely separate and reconnect the track components while properly positioning seals and bolts.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjskdmnenemm
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjjskekrtfsmem
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...ufsjekfksmem
The document provides instructions for servicing the track and track roller frames of a D6H track-type tractor. It describes removing the track roller frame by using various tools to support the tractor and remove bolts/pins connecting the frame. Reinstalling involves reversing these steps, being careful to properly align parts and fill compartments with oil. Proper safety precautions are noted when working on sloped or unstable surfaces.
Caterpillar cat d6 h track type tractor (prefix 6fc) service repair manual (6...fjsjfkskefmem
The document provides instructions for servicing a D6H track-type tractor. It begins by stating that the tractor must be on level, hard ground before separating the track roller frames. It then provides detailed steps for removing and installing the track roller frames and idlers. The removal process involves using various tools to support the frame and separate components. Reinstallation follows the reverse process.
Similar to Caterpillar cat d6 r track type tractor (prefix 1rw) service repair manual (1rw00001 and up) (12)
John deere 1565 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1545 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1445 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides instructions to check each component and make any necessary repairs or adjustments.
John deere 1435 front mower service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere front mowers models 1420, 1435, 1445, 1545, and 1565. The manual is organized into specific sections covering specifications, identification numbers, tools, component locations, schematics, theory of operation, operation and diagnostics, tests and adjustments, repair, and safety precautions. Technicians are advised to follow all safety procedures when servicing equipment to avoid injury from hazards like high pressure fluids, moving parts, hot surfaces, and heavy components.
John deere 1420 front mower service repair manualfhhjsjekmdme
The brakes on the machine are not engaging or holding the machine. Possible causes include issues with the park brake lock lever assembly, brake linkage adjustment, brake return springs, brake friction disks, or brake separator plates. The manual provides procedures to check each component and make any necessary repairs or adjustments.
John deere 1070 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. The manual is divided into sections covering safety, general specifications, repair specifications, fuel and lubricants, engine repair, electrical systems, power train repair, steering and brakes, hydraulics, and operational testing. Safety messages in the introduction warn of hazards such as high pressure fluids, battery explosions, and working with fuels and chemicals. Technicians are advised to follow safety precautions and use recommended tools and materials for repairs.
John deere 990 compact utility tractor service repair manualfhhjsjekmdme
The technical manual provides instructions for servicing a 990 Compact Utility Tractor. It contains sections on specific systems organized by contents, specifications, component location, schematics, theory of operation, troubleshooting, diagnostics, tests and adjustments, and repair. Safety procedures are outlined, including precautions for working with batteries, high pressure lines, and following proper service procedures. The document provides guidance on safely working on and repairing the tractor.
John deere 970 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. It contains sections on general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and operation/testing. The manual instructs technicians on repair procedures, specifications, safety practices, and diagnosing routine failures. It is intended to be an on-the-job guide for experienced service technicians repairing and maintaining these tractor models.
John deere 955 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides specifications and repair/removal instructions for John Deere compact utility tractors models 655, 755, 855, 955, 756 and 856. It includes sections on the diesel engine, fuel and air systems, alternator, power train, steering/brakes, hydraulics, and other components. The document provides overview information, safety messages, lubrication recommendations, component locations, and step-by-step repair guides to assist technicians in servicing the machines.
John deere 870 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides service information for John Deere 670, 770, 790, 870, 970, and 1070 compact utility tractors. It contains sections on general information, engine repair, electrical systems, power train, steering/brakes, hydraulics, and operation/testing. The manual instructs technicians on repair procedures, specifications, safety practices, and diagnosing routine failures. It is intended to be an on-the-job guide for experienced service technicians.
John deere 856 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides specifications and repair/removal instructions for John Deere compact utility tractors models 655, 755, 855, 955, 756 and 856. It covers general information, diesel engine repair, fuel and air repair, alternator repair, power train repair, steering and brakes repair, hydraulics repair, and miscellaneous repair. Repair sections provide instructions for repairing components, while diagnostic sections help identify common failures. Information is organized into groups for easy reference to specifications, tools, parts, and repair instructions for various components.
John deere 855 compact utility tractor service repair manualfhhjsjekmdme
This technical manual provides specifications and repair/removal instructions for John Deere compact utility tractors models 655, 755, 855, 955, 756 and 856. It includes sections on the diesel engine, fuel and air systems, alternator, power train, steering/brakes, hydraulics, and other components. The document provides overview information, safety messages, lubrication recommendations, component locations, and step-by-step repair guides to assist technicians in servicing the machines.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs/messages, user safe maintenance practices, a planned maintenance program, and procedures for various maintenance tasks such as inspecting wheels/tires, testing controls and brakes, checking batteries, and cleaning the truck. Regular maintenance in accordance with the manufacturer's recommendations is emphasized as important for safety and long equipment life.
Clark tmg 13 20 x forklift service repair manualfhhjsjekmdme
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Clark tmg 12 25 forklift service repair manualfhhjsjekmdme
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Clark sf20 30 dlg forklift service repair manual #2fhhjsjekmdme
The document is a service manual that provides instructions for maintaining a transaxle, including checking fluid levels, changing fluids and filters, adjusting brake clearance, and checking hydraulic pressures. Maintenance includes draining fluid from the bottom of the transmission case and filling through the dipstick tube with the engine running. Brake adjustment is accessed through openings in the backing plate or wheel hub/drum.
Clark pwx forklift service repair manualfhhjsjekmdme
This document provides information about periodic maintenance of HWX/PWX trucks, including:
1. A maintenance schedule listing tasks and suggested intervals for normal, severe, and extreme operating conditions.
2. Details of a planned maintenance program involving inspections, tests, and recording truck conditions on a checklist.
3. A sample planned maintenance report form for documenting inspections.
This service manual covers Clark PWT tow tractors and PWC center controlled pallet trucks manufactured after 1989, providing specifications and maintenance information. Standard PWT models have a 1.0 or 2.5 HP motor and can tow up to 10,000 lbs, while PWC models have a 2.5 HP motor and 6000 or 8000 lb capacity. The document includes sections on general information, electrical systems, hydraulics, drive systems, brakes, steering, load carriers, frames, and optional equipment.
Clark pwd 36 forklift service repair manualfhhjsjekmdme
This document provides instructions for performing planned maintenance on Clark industrial trucks. It outlines visual inspections, operational tests, and checks of components like the battery, tires, frame, control handle, steering, brakes, travel speeds, and coast control. Technicians are instructed to note any issues found on a check sheet using a coding system to indicate components that are OK, need adjustment, repair or replacement, or require immediate shop repair.
Clark pwd 30 40 se service repair manualfhhjsjekmdme
This document provides maintenance schedules and procedures for Clark trucks. It discusses periodic service and planned maintenance, which involve regularly scheduled inspections, adjustments, and lubrications. The document provides maintenance schedules that specify all maintenance tasks that should be performed periodically, along with suggested time intervals. It also contains sections covering planned maintenance procedures and inspection forms. The overall document provides guidance to service technicians on maintaining Clark trucks through routine maintenance.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6R TRACK-TYPE TRACTOR 1RW
Configuration: D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
D6R TRACK-TYPE TRACTOR POWER TRAIN
Media Number -SENR9496-02 Publication Date -01/11/2004 Date Updated -23/07/2018
SENR94960013
Idlers
SMCS - 4159-010; 4159-015; 4159-016
Remove & Install Idlers
Start By:
a. separate track
1. The weight of idler (1) is 143 kg (315 lb). Fasten a hoist and Tool (A) to idler (1) remove two
bolts (3) and washers from each side of the idler.
2. Remove one cap (2) from each side.
3. Lower idler (1) slightly and remove.
1/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTE: It may be necessary to raise the front of the roller frame with a small jack to provide
clearance to remove the roller.
4. Remove one block (4) from each side.
NOTE: The following steps are for installation of the idler.
5. Fasten a hoist and Tool (A) to idler (1). Put one block (4) on each side of the idler in position on
the dowel.
NOTICE
The hole in idler shaft (5) must be aligned with pin (6) in cap (2).
6. Put the idler in position on roller frame. Align the hole in idler shaft (5) with pin (6) in cap (2).
Install cap (2) with bolts (3) and washers. Tighten the bolts to a torque of 570 ± 80 N·m (420 ± 59
lb ft). Remove Tooling (A).
End By:
a. connect track
Disassemble Idlers
Start By:
a. remove idlers
1. Use a slow speed drill and a 12.7 mm (.50 in) drill bit, and remove plug (4) and stopper (3)
from the end of the shaft.
2/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. NOTICE
The shaft will be free to fall when the retainers are removed.
2. Remove eight washers and bolts (2) and retainer (1) from both sides of the idler.
3. Remove O-ring seal (6) from retainer (1).
NOTE: If the Duo-Cone seals are to be used again, put identification marks on the seals so they
can be assembled and installed in their original position.
4. Put identification marks on the Duo-Cone seal (5). Remove Duo-Cone seal (5) from retainer
(1).
5. Put identification marks on Duo-Cone seal (7). Remove Duo-Cone seal (7) and toric stabilizer
(9) from both sides of shaft (8).
6. Remove washer (10) from both ends of shaft (8).
3/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Pull shaft (8) out of the idler far enough to fasten a hoist to the shaft.
8. Fasten a hoist to shaft (8). Remove the shaft from idler assembly (11). The weight of the shaft is
21 kg (46 lb).
Assemble Idlers
1. Clean and inspect all parts for wear or damage. Replace all parts that are worn or damaged.
2. Make sure all parts are free of oil film, dust or other foreign material. Use Isopropyl Alcohol
and a clean cloth or paper towel for cleaning.
NOTICE
The bearing in idler assembly (1) can be damaged when shaft (2) is
installed in the idler.
3. Fasten a hoist to shaft (2). Carefully put shaft (2) in position in idler assembly (1).
4/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 4. Put toric stabilizers (3) in position on both ends of shaft (2).
NOTE: See Installation of Duo-Cone Floating Seals before installation of any of the Duo-Cone
seals.
5. Put toric ring (4) in position in seal ring (5). Make sure the toric ring is straight in seal ring (5).
6. Put ring (4) and seal ring (5) in Isopropyl Alcohol until the entire toric ring is wet.
7. Use Tool (A) to install the toric ring and seal ring (5) on shaft (2). Install the rings until Tool
(A) makes contact with the end of shaft (2).
8. Use a depth micrometer (6) to measure the distance between seal ring (5) and the shaft at four
locations 90 degrees apart. The difference in these four measurements must not be more than 0.80
mm (.031 in).
9. If adjustments to seal ring (5) are necessary, use Tool (A) to adjust the seal ring on the shaft.
10. Repeat Steps 5 through 9 to install the toric ring and seal ring on the other side of the idler.
5/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 11. Put O-ring seal (8) in position on seal ring (7). Make sure the O-ring seal is straight on the seal
ring.
12. Lubricate the O-ring seal on the seal ring with Isopropyl Alcohol.
13. Put the O-ring seal and seal ring (7) in position on retainer (9). Use Tool (A) and an arbor
press to install the seal ring in the retainer. Install O-ring seal and seal ring until the O-ring seal
makes contact with the bottom of the retainer.
14. Use depth micrometer (6) to measure the distance from the surface of retainer (9) to the
surface of seal ring (7) at four locations 90 degrees apart. The difference in these measurements
must not be more than 0.30 mm (.012 in).
15. If adjustments to the seal are necessary, use Tool (A) to adjust the seal ring in the retainer.
16. Put O-ring seal (10) in position in the groove in retainer (9).
17. Put Vaseline or grease on O-ring seal (10) to it in place on the retainer.
6/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 18. Install washer (11) on the end of shaft (2).
19. Make sure the faces of the seal rings are clean and free of any foreign material.
20. Put a thin film of clean oil on the faces of the seal rings.
21. Put Tool (B) in position in the bores of retainer (9) and the seal ring. Use Tool (B) to put the
seal ring and retainer (9) in their original position on the idler assembly.
22. Use Tool (B) to hold the seal ring and retainer (9) in the correct position on the idler assembly.
23. Install bolts (12). Tighten the bolts evenly to keep retainer (9) in alignment with the idler
assembly.
24. Tighten bolts (12) to a final torque of 70 ± 15 N·m (52 ± 11 lb ft).
25. Repeat Steps 11 through 24 to install the retainer on the other side of the idler.
26. Use Tool (D) to pressure test the idler assembly as follows:
a. Put air (free of water) under a pressure of 280 kPa (41 psi) in the idler shaft.
b. If there is a pressure reduction in ten seconds or less, there is a leak in the idler assembly. The
idler assembly must be disassembled and checked.
7/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 27. Use Tool (E) to check the end play of shaft (2). The end play must be 0.25 mm to 0.85 mm
(.010 to .034 in).
28. Fill idler shaft (2) with 650 ± 15 mL (22.1 ± .5 oz.) of SAE 30W oil.
29. Put clean oil on stopper (13). Install the stopper in the end of shaft (2). Install the stopper until
it is 10 ± 4 mm (.393 ± .16 in) below the surface of the end of the shaft.
30. Use Tool (C) to install plug (14) in the stopper. Install the plug so it is even with the end of the
stopper.
End By:
a. install idler
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 12:31:01 UTC+0800 2020
8/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6R TRACK-TYPE TRACTOR 1RW
Configuration: D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
D6R TRACK-TYPE TRACTOR POWER TRAIN
Media Number -SENR9496-02 Publication Date -01/11/2004 Date Updated -23/07/2018
SENR94960014
Equalizer Bar
SMCS - 7206-011; 7206-012; 7206-017
Remove Equalizer Bar
1/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. *Increase thread to 2 1/4" on both ends of 9H1080 stub
Start By:
a. remove track roller frame
1. Put Tooling (A) in position under the side of the equalizer bar that the track roller frame was not
removed. Push the side of the equalizer bar up and remove bar stock (1), that was installed
between the frame and the equalizer bar, when the track roller frame was removed.
2/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 2. Put enough wooden blocks (2) under the track roller frame so that when Tooling (A) is
removed, the equalizer bar does not make contact with the frame on the side that the track roller
frame was removed. Remove Tooling (A).
3. Remove retaining bolt (3) not shown. Install Tooling (B) on the pin. Make sure the FT1713
Wedges [part of Tooling (B)] are put in position between the equalizer bar and the saddle to
prevent the pin from binding as it is removed. Use Tooling (B) and remove the equalizer bar pin.
4. Put the FR1713 Wedges [part of Tooling (D)] in between the equalizer bar and the saddle to
prevent the pin from binding as it is removed.
5. Remove three bolts (4) and the retainer plate.
6. The weight of the equalizer bar is 143 kg (315 lb). Put Tooling (C) in position under the
equalizer bar and fasten wire (5) to Tooling (C) so the equalizer bar will not fall when it is
removed.
3/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 7. Install Tooling (D) and remove the equalizer bar center pin. Remove Tooling (D).
8. Lower the equalizer bar with Tooling (C). Remove spacer (6) from each side of the equalizer
bar and remove the bar from under the machine.
Install Equalizer Bar
1. Position the equalizer bar on Tooling (C). Fasten the equalizer bar with wire (5) to Tooling (C).
Put the equalizer bar in position under the machine.
2. Put a small amount of 5P-0960 Multipurpose Type Grease on the two lip seals and on the center
equalizer bar bearing.
3. Put two spacers (6) in position, one on each side of the equalizer bar.
4/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 4. Put the equalizer bar in position in the equalizer bar saddle with Tooling (C).
NOTICE
The 2P2506 Anti-Seize Compound should not be permitted to get in the
bearing area of the equalizer bar.
5. Put 2P-2506 Anti-Seize Compound in the front bore of the equalizer bar saddle and on the rear
diameter of equalizer bar center pin (7).
6. Align the bores in the equalizer bar saddle with the bore in the equalizer bar. Install equalizer
bar center pin (7). Make sure the flats on the end of the pin are horizontal so the retainer plate can
be installed properly.
7. Put the retainer plate in position and install three bolts (4). Remove wire (5) and Tooling (C).
8. Align the bore in the equalizer bar and the bores in the track roller frame. Install pin (8) and
retaining bolt (3).
5/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 9. Use Tooling (A) to raise the equalizer bar and track roller frame. Remove wooden blocks (2)
from under the track roller frame.
10. Put bar stock (1), that was removed earlier, between the equalizer bar and the frame, as shown.
It will put the equalizer bar in its original position so the track roller frame can be installed. Lower
the equalizer bar and track roller frame. Remove Tooling (B).
End By:
a. install track roller frame
Disassemble & Assemble Equalizer Bar
Start By:
a. remove equalizer bar
6/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Use a hammer and punch to bend the outside ring of seals (1) toward the center. Do this in
several places and remove seals (1).
2. Use Tooling (A) and remove the center bearing from the equalizer bar.
3. Use a hammer and a punch to bend the outside rings of lip seals (2) toward the center. Do this
in several places and remove seals (2). Do this at both ends of the equalizer bar.
4. Use Tooling (B) and remove the retaining rings from each side of the spherical bearings.
7/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 5. Use Tooling (C) and remove end bearings (3) from the equalizer bar.
NOTE: The following Steps are for assembly of the equalizer bar.
6. Use Tool (B) and install one of the retaining rings in the end of the equalizer bar. Use Tooling
(D) and install bearing (3) against the retaining ring. Use Tool (B) and install the other retaining
ring.
7. Repeat Step 6 at the opposite end of the equalizer bar. Put 5P0960 Multipurpose Type Grease
on the spherical surface of bearings (3) and in the pin bores.
8. Put 5P3413 Pipe Sealant with Teflon on the inner diameter surfaces of the equalizer bar and
install lip seals (2) at the center bore.
9. Put 6V1541 Quick Cure Primer on the center pin bore of the equalizer bar and allow it to dry.
Put 9S3265 Retaining Compound on the center bore.
10. Use Tooling (E) and install the center bearing in the equalizer bar. The bearing should be
installed so it is the same distance from the front and the rear of the equalizer bar.
11. Put 5P3413 Pipe Sealant with Teflon on the inner diameter of the equalizer bar and install
seals (1) on each side of the bearing.
End By:
a. install equalizer bar
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 12:31:50 UTC+0800 2020
8/8D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6R TRACK-TYPE TRACTOR 1RW
Configuration: D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
D6R TRACK-TYPE TRACTOR POWER TRAIN
Media Number -SENR9496-02 Publication Date -01/11/2004 Date Updated -23/07/2018
SENR94960015
Pivot Shaft (Stub Shaft)
SMCS - 4153-010
Remove & Install Pivot Shaft (Stub Shaft)
Start By:
a. remove track roller frame
1. Attach a hoist to Tooling (A). Use a nylon strap and attach it to Tooling (A).
2. The weight of stub shaft (1) is 67 kg (148 lb). Remove eight bolts (2) and the stub shaft.
NOTE: The following Steps are for installation of the stub shaft.
3. Put 5P-3931 Anti-Seize Compound on the pilot diameter that goes in the main case and frame.
1/2D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 4. Use a hoist and Tooling (A), put stub shaft (1) in position, and install eight bolts (2).
End By:
a. install track roller frame
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 12:32:39 UTC+0800 2020
2/2D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6R TRACK-TYPE TRACTOR 1RW
Configuration: D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
D6R TRACK-TYPE TRACTOR POWER TRAIN
Media Number -SENR9496-02 Publication Date -01/11/2004 Date Updated -23/07/2018
SENR94960016
Final Drive Planetary Carriers (In Chassis)
SMCS - 4092-011; 4092-012
Remove Final Drive Planetary Carriers (In Chassis)
1/5D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 1. Position the final drive drain plug (3) on the bottom as shown. Remove drain plug (3) and drain
approximately 11.4 liters (3 U.S. gal.) of oil from the final drive.
2. Remove the center cover. Remove the O-ring seal from the cover.
3. Use Tooling (A) and remove outer axle (2).
NOTICE
Three bolts [Tooling (B)] must be threaded in 25.4 mm (1 in) to hold
the planetary carrier.
4. Remove three equally spaced bolts that hold planetary carrier (5) to hub (4). Install Tooling (B)
in place of three bolts as shown.
5. Remove the remaining bolts (1) that hold the planetary carrier to the hub.
6. Use a pry bar and move planetary carrier (5) out of the hub as far as the bolts [Tooling (B)] will
permit.
2/5D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 7. Adjust the upper hanger bracket on Tooling (C) so distance (X) is 203 mm (8 in). Install lower
plate (6) so the spacers are down and toward the vertical leg of the bracket.
8. Attach a hoist to Tooling (C) and install it on the planetary carrier.
9. The weight of the planetary carrier is 132 kg (290 lb). Remove the three bolts [Tooling (B)] and
remove planetary carrier (5) from the hub. Remove the O-ring seal.
10. To disassemble the planetary carrier, see Disassemble Final Drive in this module.
Ring gear (8) will be free to fall when retainer (7) is removed. To
prevent possible personal injury, Tooling (D) and (E) must be in
position to hold ring gear (8) and the hub in position when retainer (7)
is removed.
11. Put Tooling (D) under final drive hub (4) to hold it in position when retainer (7) is removed.
Install Tooling (E) to hold ring gear (8) in position. Use the bolts that hold the planetary carrier in
position to install Tooling (E).
12. Remove the bolts and retainer (7).
13. Remove the lip seal from the end of the spindle.
3/5D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Install Final Drive Planetary Carriers (In Chassis)
1. Use Tooling (F) and install lip seal (9) in the end of the spindle. The lip of the seal must be
toward the inside of the spindle. Put clean oil on the lip of the seal.
2. Put retainer (7) in position on the spindle and install the bolts that hold it. Tighten the bolts to a
torque of 135 ± 15 N·m (100 ± 11 lb ft).
3. Remove Tooling (D) and (E) from the final drive.
4/5D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 4. For assembly of the planetary carriers, see topic, Assemble Final Drive in this module.
5. Install the O-ring seal on the planetary carrier.
6. Use Tooling (C) and a hoist and put the planetary carrier in position on the hub. Push the
planetary carrier in until it is approximately 25.4 mm (1 in) from the hub.
7. Thread three bolts [Tooling (B)] in 25.4 mm (1 in), evenly spaced, to support the planetary
carrier. Remove Tooling (C).
8. Install bolts (1). Remove Tooling (B) and install the remaining three bolts that hold the
planetary carrier to the hub.
9. Use Tooling (A) and install outer axle (2).
10. Install the O-ring seal on the cover and install the cover on the final drive.
11. Drain plug (3) must be toward the bottom. Fill the final drive with oil to the bottom of the fill
plug. See the Operation And Maintenance Guide for the correct oil and the capacity.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 20 12:33:28 UTC+0800 2020
5/5D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: TRACK-TYPE TRACTOR
Model: D6R TRACK-TYPE TRACTOR 1RW
Configuration: D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWERED BY 3306 Engine
Disassembly and Assembly
D6R TRACK-TYPE TRACTOR POWER TRAIN
Media Number -SENR9496-02 Publication Date -01/11/2004 Date Updated -23/07/2018
SENR94960017
Final Drives
SMCS - 4050-011; 4050-012; 4050-015; 4050-016
Remove Final Drives
Start By:
a. separate track
NOTE: The final drive planetary carriers can be removed in chassis. See topic, Remove Final
Drive Planetary Carriers (In Chassis).
1. Turn the final drive until drain plug (1) is on the bottom as shown. Remove drain plug (1) and
drain approximately 13.2 liters (3.4 U.S. gal.) of oil from the final drive.
1/12D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 2. Remove the cover from the final drive and remove the O-ring seal from the cover.
3. Install Tooling (A) and remove the outer axle.
4. Adjust the top bracket on Tooling (B) so that dimension (X) is 213 mm (8.4 in). The lower
mounting bracket must be installed with the spacers outward as shown.
5. Remove two of the bolts from the sprocket segments. Fasten a hoist and install Tooling (B) on
the final drive.
NOTICE
Bolts (4) hold the steering clutch and brake to the main case and frame.
Do not remove bolts (4).
2/12D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 6. Remove bolts (2) that hold the final drive to the main case and frame.
7. The weight of the final drive is 490 kg (1075 lb). Remove four bolts (3) that hold the final drive
and steering clutch and brake together.
8. Use Tooling (B) and remove the final drive from the machine.
9. Remove the O-ring seal from either the face of the steering clutch or the final drive hub.
Install Final Drives
1. Inspect the condition of O-ring seals and replace if necessary.
2. Put the O-ring seal in position on the face of the steering clutch.
3. Fasten a hoist and install Tooling (B) on the final drive. Adjust Tooling (B) if necessary to put
the final drive in a level position.
3/12D6R Track-Type Tractor Differential Steering 1RW00001-UP (MACHINE) POWER...
2020/4/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...