This document provides information about periodic maintenance of HWX/PWX trucks, including:
1. A maintenance schedule listing tasks and suggested intervals for normal, severe, and extreme operating conditions.
2. Details of a planned maintenance program involving inspections, tests, and recording truck conditions on a checklist.
3. A sample planned maintenance report form for documenting inspections.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. CONTENTS
SM 781, May '07 CONTENTS -1
Contents by Group
Contents are listed here by Group number :
PS PERIODIC SERVICE
12 BATTERY
14 WIRING
16 ELECTRIC MOTORS
17 CONTACTORS
19 MOTOR CONTROLS
20 DRIVE UNIT
23 BRAKE SYSTEM
25 CASTER ASSEMBLY
28 HYDRAULIC SYSTEM
34 LIFT CYLINDERS
35 LIFT LINKAGE and LOAD WHEELS
39 SHEET METAL
40 SPECIFICATIONS
3. Copyright Clark Material Handling 2007 SM781, May ’07
Truck Models Covered by this Manual
This manual consists of “base” module that pertains
to all HWX/PWX models and other modules that
pertain only to specific models. Manuals shipped
with the truck contain the base module and the mod-
ules specific to the purchased truck.
You may, however, purchase specific modules and
expand your manual to fully cover multiple models.
To do so, order the desired modules as you would
any other Clark part.
Arrangement and Use of this Manual
Clark arranges parts and service procedures by stan-
dardized Groups. In this manual, Groups are similar
to “chapters”. Groups are listed in the indexes on the
next page.
Each Group begins with a table of contents that
shows the Sections contained within the Group.
Lengthy Sections also begin with a table of contents.
Each Group and Section has an identifying name and
number, or “ID”.
Each page also has a unique ID. The page ID con-
sists of three numbers separated by hyphens. The
three numbers represent the Group number, the Sec-
tion number, and the page number. For example,
“00-1-2” on the lower corner of the page indicates
Group 00, Section 1, page 2.
The Group number sometimes has a letter or letters
added to it in parentheses if one or more variations of
the Group exist. For example, if the truck has a stan-
dard transaxle, Group 06 is expressed as “06(S)”; if
the truck has a hydrostatic transmission, Group 06 is
expressed as “06(H)”.
You can quickly locate a specific point in the manual
by using the headers and footers that appear on every
Section page. The following illustration points out
these areas.
This manual is intended for the use of trained service
personnel. Please read Group SA, “Safe Mainte-
nance”, and the Operator’s Manual before working
on or operating the truck.
4. GROUP PS PERIODIC SERVICE
SM 781, May '07 Group PS PERIODIC SERVICE,
GROUP PS
PERIODIC SERVICE
Maintenance Schedule .................................... Section 1
Planned Maintenance Program ...................... Section 2
The PM Inspection Form ................................. Section 3
5. Group PS, Periodic Service
SM 781, May ’07 Maintenance Schedule • PS-1-1
“Periodic Service” and “Planned Main-
tenance”
The term “periodic service” includes all maintenance
tasks that should be performed on a regularly scheduled
basis.
The term “Planned Maintenance” indicates a formalized
program of basic inspections, adjustments, and lubrica-
tions that the Clark service organization provides custom-
ers at a prescribed interval, usually 50-250 hours. The
recommended basic “Planned Maintenance” procedure is
given in Section 2 of this Group.
The current Section,”Maintenance Schedules,” specifies
all maintenance tasks.including Planned Maintenance
tasks.that should be performed periodically, and suggests
intervals at which they should be performed.
Determining Maintenance Intervals
Time intervals on the charts on the next four pages and
elsewhere in this manual relate to truck operating hours as
recorded on the hourmeter, and are based on experience
Clark has found to be convenient and suitable under nor-
mal operation. Standard operating condition classifica-
tions are:
Normal Operation: Eight-hour material handling, mostly
in buildings or in clean, open air on clean, paved surfaces.
Severe Operation: Prolonged operating hours or constant
usage.
Extreme Operation:
• In sandy or dusty locations, such as cement plants,
lumber mills, and coal dust or stone crushing sites.
• High-temperature locations, such as steel mills and
foundries.
• Sudden temperature changes, such as constant trips
from buildings into the open air, or in refrigeration
plants.
If the lift truck is used in severe or extreme operating con-
ditions, the maintenance intervals should be shortened
accordingly.
IMPORTANT
MAINTENANCE INTERVALS. If the lift
truck is used in severe or extreme operating
conditions, the maintenance intervals should
be shortened ace. Put upright in vertical posi-
tion and fully lower the forks or attachment.
Section 1.
Maintenance Schedule
6. Group PS, Periodic Service
SM 781, May ’07 Planned Maintenance Program • PS-2-1
P.M. CHECK SHEET
A special coding system on the P.M. Check Sheet allows
truck condition to be reported with a minimum number of
words. As the P.M. is performed, a check mark should be
made in the appropriate box of the component being
checked.
• ( √ ) indicates the particular truck component or
system has been checked and is O.K.
• (x) indicates the component or system is in need of
a minor adjustment or service (not part of the nor-
mal P.M.) that should be taken care of in the near
future.
• (r) indicates there is a potential problem that could
result in damage to a component or system and
requires attention.
• (s) indicates the need for urgent repair or replace-
ment of a component or system and the truck
should be shut down as eminent damage or possi-
ble injury may result.
The nature of problems found during a PM should be
noted in the “comments” portion of the check sheet.
Whenever a system or component is faulty or unsafe, it
must be noted on the check sheet, and reported to the des-
ignated authority at the conclusion of the P.M.
WARNING
!
Remove all jewelry before examining electri-
cal components.
Visual Inspection
A. Oil leaks √
B. Switches √
C. Drive Tire √
D. Load Wheels √
E. Caster Wheels √
F. Control Linkage √
Operational Tests
A. Brakes s
B. Brake Switch r
C. Horn √
D. Steering √
E. Speed Control x
F. Lift and Lower Control √
CODE
√ = O.K
O.K. x = Adjust(Not P.M)
Pontential r = Repair or Replace
Urgent s = Requires Shop Repair
Section 2.
Planned Maintenance Program
7. Group PS, Periodic Service
PS-2-2 • Planned Maintenance Program SM 781, May ’07
Visual Inspection
1, Inspect Battery Plug & Truck Recelitacle
• Disconnect battery from truck.
• Inspect the spring loaded connectors in the truck
battery receptacle and check the battery plug con-
nectors. Severely burned connectors should be
noted on the P.M. check sheet.
2, Inspect Battery Cover for damage
• The cover should not be dented. A badly dented
Check Cover for Damage cover could short out
across the battery cell connectors.
• The cover should be free to swing open and closed
without binding.
3_ Inspect Pallet Forks for obvious damage
• Forks should not be bent or warped. If the forks are
damaged, report condition to the designated
authority.
4. Rider Models
• l Inspect Frame Components
• l Check truck console, access cover and doors for
damage.
• l Inspect nameplates and decals for damage and to
be sure they are not missing.
8. Group PS, Periodic Service
SM 781, May ’07 Planned Maintenance Program • PS-2-3
4A. Walkie Models
• Inspect Frame Components
• Check truck console, access cover and doors for
damage.
• Inspect nameplates and decals for damage and to
be sure they m not missing.
5, Check for obvious oil leaks
• Make a quick overall inspection for leakage. If an
oil leak appears to be major, note condition on the
check sheet for immediate attention. Minor leaks
should be repaired during the P.M.
6. Inspect Tires & Wheels
• Check for obvious damage to tires on the load,
caster and drive wheels.
• Look for excessive tire wear, cuts, breaks, chunk-
ing or bond failure between the tires and wheels.
Note condition on the PM check sheet.
• Remove embedded objects from the tires.
• Be sure, wheel fasteners are secure and none are
missing.
• Make certain grease fittings are not damaged or
missing.
7. Expose Internal Components
• Open the access doors exposing the drive unit,
brake, lift cylinder, hydraulic unit and SCR control.
Each door hangs on a hinge pin. Lift the doors
from their pins and set them to one side.
9. Group PS, Periodic Service
PS-2-4 • Planned Maintenance Program SM 781, May ’07
8. Connect Truck Battery
• Connect truck battery and check truck operation.
Operational Tests
9. All Models
• Turn the key switch on.
10. All Models
Check the horn to be sure it operates.
11. All Models
• Check the hour meter to be sure it operates.
10. Group PS, Periodic Service
SM 781, May ’07 Planned Maintenance Program • PS-2-5
12. Check Steer Control Handle
• Walkie Models
• Be certain the control handle is mounted securely
at the base of the drive unit.
• Make sure fasteners are tight and none are none
missing.
• Rider Models
• Check the mounting bracket to be sure it is
securely mounted to the base of the drive unit.
• Make sure fasteners are tight and none are missing.
13. Check Steering
• Operate truck in reverse at a slow rate of speed.
Move control handle through a full right and full
left turn. Steering should be smooth without bind-
ing or hesitation.
• If there is binding, hard spots or movement appears
to be stiff this indicates either lack of lubrication,
misadjusted or damaged steering ring.
• Report condition on the P.M. check sheet.
14. Check Brake Oneration
• Move the steer control handle downward 10 °
degrees from vertical (brake on) position.
• Operate truck in reverse at a slow rate of speed.
• Slowly move control handle upward from the 10 °
travel (brake off) position.
As Control Handle
annroaches "Brake On" position:
1. The brake switch should operate shutting off the
drive motor.
2. The brake should operate bringing the truck to a stop.
11. Group PS, Periodic Service
PS-2-6 • Planned Maintenance Program SM 781, May ’07
• Operate the truck in forward at a slow rate of
speed.
• Slowly move control handle upward from the 10 °
(brake off) position. The brake should apply when
handle reaches the full up (brake on) position.
• Now, check the brake at a high rate of speed in
both forward and reverse directions.
14A. Next, check for proper brake operation by moving
the handle downward from the 10 ° (brake off)
position. The brake check should be done at Low
and High Speeds, and in Forward & Reverse direc-
tions.
• If operation is not satisfactory, note condition on
the P.M. check sheet. Report condition to desig-
nated authority for immediate attention.
NOTE
Plugging Control is normally used for grad-
ual brake applications. Braking with the
steer control handle is normally used in
emergency situations and parking the truck.
WARNING
!
After checking the coast control, be certain to
deactivate this function position before
resuming normal truck travel.
15. Optional Coast Control (HWX Models)
The coast control deactivates the brake and
enables the truck to be "jogged" with the travel
control and coasted for order picking.
• Press the two order picking switches at the same
time for 1 sec to activate the coast control function.
• Select the Forward switch ON and press one of the
order picking switches for 1 sec to deactivate the
coast control function.
CAUTION
!
Be sure the brake switch should be OFF
position during activating the coast control
function.
16. Check Travel Speeds Check Acceleration
Check High Speed
• Drive truck in a straight line, looking in the direc-
tion of travel.
• Listen for any unusual drive train noise.
• Accelerate from low to high speed. Acceleration
should be a smooth transition from creep through
12. Group PS, Periodic Service
SM 781, May ’07 Planned Maintenance Program • PS-2-7
top speed. If transition is erratic, the accelerator
circuit should be checked.
17. Check Hi-Speed Control
• Drive truck forward, in a straight line of travel.
• Fully rotate Directional Speed Control (1) until
maximum (solid state control) speed is obtained
• Depress Hi-Speed Button (2). This transition
should be smooth. If it is not, if it is erratic, jerky
etc., the accelerator should be adjusted (Group 19).
Note condition on the P.M. check sheet.
18. Override Control
• The override control is used to by-pass the emer-
gency reversal switch circuit. This is desirable
when the truck is operating in areas where plastic
strip curtain doors (etc.) are used.
• Example:
• When moving a truck through this type door, pres-
sure from the door strips can cause the emergency
reversal switch to operate changing the direction of
truck travel. By overriding the reversal switch, the
truck can pass through the curtain door without
miss hap.
• To simulate the above, operate truck in slow speed
reverse. "Depress button to override" and then
depress the reversal (belly) switch. Truck travel
should remain in slow speed reverse. Note condi-
tion on the P.M. check sheet.
19. Elevate and Lower Pallet Forks
• Elevate pallet forks to maximum lift height. As the
forks elevate, check to be sure they elevate
smoothly and evenly without binding.
• Lower forks. Look for erratic motion as they lower.
They should lower smoothly without hesitation.
• If there is erratic, jerking motion or binding of
linkage as the forks elevate or lower, the lift link-
age should be checked and adjusted (Group 35).
Note condition on the P.M. check sheet.
20. Discharge the Capacitors
• Be sure the battery is unplugged.
• Discharge capacitors using a 100 ohm, 10 watt
resistor connected between the Positive and Nega-
tive power terminals on the control. Hold the resis-
tor in place for 10 seconds before removing.
13. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
14. Group PS, Periodic Service
PS-2-8 • Planned Maintenance Program SM 781, May ’07
CAUTION
!
Using a shorting device without a "resistor
load" could cause damage to the control.
WARNING
!
Discharging the capacitors without using
specified resistor could cause serious Injury
to yourself and bystanders.
WARNING
!
Prior to discharging the capacitors, make
certain the cover is installed on the control
panel power base.
21. HWX Models
• Inspect Operator Grab Rail
• Check hand rail for security of mounting. Try mov-
ing hand rail fore and aft checking for loose con-
nections and damage. The mounting bolts should
be torqued to lOO- 120 lb. in.
• Make certain the switch housing is mounted
securely and the switches are not damaged.
• Check wire harness condition. Check for loose
connections and harness damage. Report condition
on P.M. check sheet
15. Group PS, Periodic Service
SM 781, May ’07 The PM Inspection Form • PS-3-1
• As an aid to service technicians performing and
documenting PM inspections, Clark has prepared
an Electric Truck Planned Maintenance Report
form. (Sample appears on the next page.)
• Use this form as a checklist, and make a record of
your inspection and truck condition. Note the spe-
cial coding system for indicating the importance of
needed repairs and/ or adjustments.
Section 3
The PM Inspection Form