This document provides disassembly instructions for the transmission planetary system of a 972G II Wheel Loader. It outlines 67 steps to fully disassemble the transmission, including removing housing components, clutches, gears, shafts, seals and other internal parts. Special tools and safety precautions are noted. The process involves separating the transmission from other components, then systematically removing internal components using tools like pullers, spacers, rods and presses. Weights of removed parts are provided.
Caterpillar Cat 972G SERIES II WHEEL LOADER (Prefix AXP) Service Repair Manua...9fikslkddmd8u
This document provides disassembly instructions for the transmission of a 972G II Wheel Loader. It lists 59 steps to fully disassemble the transmission. The steps include removing housing components, planetary gears, carriers, shafts, seals, plates, rings, and other internal parts. Special tools and safety precautions are noted throughout the process. The goal is to disassemble all individual parts for cleaning, inspection, or replacement.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other components. Special tools and lifting devices are required due to the heavy weight of some parts. Cautions are provided regarding spring forces and keeping parts clean.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The transmission disassembly procedure involves removing over 50 individual parts in a specific sequence, including removing planetary gears, carrier assemblies, clutch housings, pistons, seals, gears, shafts, and other internal components using various tools like pullers and spacers. Technicians are advised to mark all lines and tubes to prevent fluid loss and keep the transmission clean to prevent dirt from entering during disassembly. Detailed illustrations accompany each step to show how to properly disassemble the transmission components.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The document outlines 51 steps to fully disassemble the transmission of a 972G wheel loader, removing components like gears, shafts, housings, seals, and other parts. Technicians are instructed to mark components, use proper safety equipment, cleaning procedures, and tools to carefully disassemble each part.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The document outlines 51 steps to fully disassemble the transmission of a 972G wheel loader, removing components like gears, shafts, housings, seals, and other parts. Technicians are instructed to mark components, use proper safety equipment, cleaning procedures, and tools to carefully disassemble each part.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The document outlines 51 steps to fully disassemble the transmission of a 972G wheel loader, removing components like gears, shafts, housings, seals, and other parts. Technicians are instructed to mark components, use proper safety equipment, cleaning procedures, and tools to carefully disassemble each part.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The transmission disassembly procedure involves removing over 50 individual components like gears, shafts, housings, seals, and fasteners using specialized tools like pullers and spacers, with notes to identify parts and plug openings to prevent fluid loss and contamination. Detailed illustrations accompany each step to show how to access and remove each transmission subassembly and part in the correct sequence. Special care must be taken when compressing springs or removing heavy components using lifting devices due to potential safety hazards.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like clutches, carriers, gears, shafts, seals and housings. Special tools are required and safety precautions noted. Detailed illustrations accompany each step to ensure proper disassembly.
Caterpillar Cat 972G SERIES II WHEEL LOADER (Prefix AXP) Service Repair Manua...9fikslkddmd8u
This document provides disassembly instructions for the transmission of a 972G II Wheel Loader. It lists 59 steps to fully disassemble the transmission. The steps include removing housing components, planetary gears, carriers, shafts, seals, plates, rings, and other internal parts. Special tools and safety precautions are noted throughout the process. The goal is to disassemble all individual parts for cleaning, inspection, or replacement.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other components. Special tools and lifting devices are required due to the heavy weight of some parts. Cautions are provided regarding spring forces and keeping parts clean.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The transmission disassembly procedure involves removing over 50 individual parts in a specific sequence, including removing planetary gears, carrier assemblies, clutch housings, pistons, seals, gears, shafts, and other internal components using various tools like pullers and spacers. Technicians are advised to mark all lines and tubes to prevent fluid loss and keep the transmission clean to prevent dirt from entering during disassembly. Detailed illustrations accompany each step to show how to properly disassemble the transmission components.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The document outlines 51 steps to fully disassemble the transmission of a 972G wheel loader, removing components like gears, shafts, housings, seals, and other parts. Technicians are instructed to mark components, use proper safety equipment, cleaning procedures, and tools to carefully disassemble each part.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The document outlines 51 steps to fully disassemble the transmission of a 972G wheel loader, removing components like gears, shafts, housings, seals, and other parts. Technicians are instructed to mark components, use proper safety equipment, cleaning procedures, and tools to carefully disassemble each part.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The document outlines 51 steps to fully disassemble the transmission of a 972G wheel loader, removing components like gears, shafts, housings, seals, and other parts. Technicians are instructed to mark components, use proper safety equipment, cleaning procedures, and tools to carefully disassemble each part.
This document provides disassembly instructions for the transmission of a 972G wheel loader in 3 sentences:
The transmission disassembly procedure involves removing over 50 individual components like gears, shafts, housings, seals, and fasteners using specialized tools like pullers and spacers, with notes to identify parts and plug openings to prevent fluid loss and contamination. Detailed illustrations accompany each step to show how to access and remove each transmission subassembly and part in the correct sequence. Special care must be taken when compressing springs or removing heavy components using lifting devices due to potential safety hazards.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like clutches, carriers, gears, shafts, seals and housings. Special tools are required and safety precautions noted. Detailed illustrations accompany each step to ensure proper disassembly.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like the carrier assembly, ring gears, sun gears, planetary gears, clutch housings, and seals. Special tools are required and safety precautions mentioned, as some components contain spring forces or are heavy. Detailed illustrations accompany each step.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like clutches, carriers, gears, shafts, seals and housings. Special tools and lifting devices are required due to the heavy weight of some parts. Care must be taken when compressing springs or pushing out pressed components to avoid injury.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like the carrier assembly, ring gears, sun gears, planetary gears, clutch housings, and seals. Special tools are required and safety precautions mentioned, as some components contain compressed springs. Detailed illustrations accompany each step to ensure proper disassembly.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 50 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other components. Detailed illustrations accompany each step. Safety warnings are provided to properly release spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 50 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other components. Detailed illustrations accompany each step. Safety warnings are provided to properly release spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing housing components, shafts, gears, seals, springs, and sensors. Detailed illustrations accompany each step to show how to remove specific parts. Safety precautions are provided, and all necessary tools are listed at the beginning.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing housing components, shafts, gears, seals, springs, and sensors. Detailed illustrations accompany each step to show how to remove specific parts. Safety precautions are provided, and all necessary tools are listed. The goal is to disassemble the entire transmission down to individual parts for repair or replacement.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing housing components, clutches, gears, shafts, seals and other internal parts. Detailed illustrations accompany each step to show how to remove each component. Safety precautions are provided, and all necessary tools are listed at the beginning.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, shafts, gears, seals, springs, and other internal parts. Detailed illustrations accompany each step to show how to remove each component. Safety precautions are provided, and all necessary tools are listed at the beginning. The overall process dismantles the entire transmission down to its individual parts.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and sensors. Precision tools are required and care must be taken due to heavy component weights and stored spring energies. Detailed illustrations accompany each step to ensure correct part identification and procedure.
Kubota B1710D Tractor Parts Catalogue Manual (Publishing ID BKIDK0391).pdfjnnfnjsdnnd
This document provides a parts list for frequently used engine parts. It includes the part number, name in Polish and English, quantity, serial number, weight, and remarks for each part. Common parts listed include starters, switches, fuses, filters, gaskets, bolts, and more. The document is published by Kubota and copyrighted for 2015.
Kubota B1700-HD Tractor Parts Catalogue Manual (Publishing ID BKIDA0020).pdfjnnfnjsdnnd
This document provides a parts list for a Kubota B1700-HD engine, including the crankcase, oil pan, cylinder head, gear case, and head cover. It lists 170 part numbers, part names in Polish and English, quantities, serial numbers if applicable, weights in kg, and other remarks. The parts list is divided into sections for the main engine components and subsections for individual parts within each component.
Volvo EC55-2 Compact Excavator Parts Catalogue Manual – SN 5001 - 7620.pdfjnnfnjsdnnd
This document contains specifications for various engine parts for a Volvo EC55-2 engine. It includes sections for the engine, cylinder head, valves, pistons, connecting rods, camshaft, and other components. Each section lists the relevant part numbers, descriptions, quantities, and other details. The document provides an extensive catalogue of replacement parts for this engine model.
Kubota B1241D-EC-F2-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA516...jnnfnjsdnnd
This document provides a parts list for frequently used items and their information. It includes 30 parts ranging from switches and fuses to hoses and filters. Each part is listed with its number, name in Polish and English, quantity, and other identifying information like serial number and weight. The document is copyrighted by KUBOTA in 2015.
Kubota B1700D Tractor Parts Catalogue Manual (Publishing ID BKIDK0093).pdfjnnfnjsdnnd
This document provides a parts list for a crankcase (Kurbelgehäuse) with part numbers, names, quantities, serial numbers, and other details. It lists over 200 individual part numbers. The parts are for various engine components, including the crankcase, oil pan, cylinder head, gear case, and head cover.
Kubota B1181DT-F2-EC-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA51...jnnfnjsdnnd
This document provides a parts list for the main bearing case of an engine. It includes the part numbers, names, quantities, and other details for over 20 parts that make up the main bearing case assembly. Key components listed include the main bearing case group, bearing case cover, oil seal, gaskets, bolts, and bearing shells. The document also provides copyright information at the bottom of each page.
Kubota B1241D-EC-F Tractor Parts Catalogue Manual (Publishing ID BKIDA5131).pdfjnnfnjsdnnd
This document provides a list of parts for an engine. It includes the part numbers, names in Polish and English, quantities, and other specifications for 230 different engine parts organized into categories like crankcase, oil pan, cylinder head, gear case, and head cover. The parts range from bolts, nuts, and plugs to larger assemblies and components like the crankcase, cylinder head, and gear case.
Kubota B1181D-EC Tractor Parts Catalogue Manual (Publishing ID BKIDA5129).pdfjnnfnjsdnnd
This document provides a parts list for a Kubota engine. It includes 230 parts ranging from starters, switches, fuses, filters, hoses, belts, and other engine components. Each part is listed with the part number, name in Polish and English, quantity, serial number if applicable, weight, and any remarks. It appears to be a comprehensive listing of components for a Kubota engine.
Kubota B1121D-F2-EC-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA515...jnnfnjsdnnd
This document provides a parts list for the main bearing case of an engine. It includes the part numbers, names, quantities, and other details for over 100 individual parts that make up the main bearing case assembly. The parts include the main bearing case group, bolts, pins, seals, gaskets, covers, and bearings.
More Related Content
Similar to Caterpillar Cat 972G II Wheel Loader (Prefix AXC) Service Repair Manual (AXC00001 and up).pdf
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like the carrier assembly, ring gears, sun gears, planetary gears, clutch housings, and seals. Special tools are required and safety precautions mentioned, as some components contain spring forces or are heavy. Detailed illustrations accompany each step.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like clutches, carriers, gears, shafts, seals and housings. Special tools and lifting devices are required due to the heavy weight of some parts. Care must be taken when compressing springs or pushing out pressed components to avoid injury.
This document provides disassembly instructions for the transmission planetary system of a 972G wheel loader. It outlines 67 steps to fully disassemble the transmission, including removing components like the carrier assembly, ring gears, sun gears, planetary gears, clutch housings, and seals. Special tools are required and safety precautions mentioned, as some components contain compressed springs. Detailed illustrations accompany each step to ensure proper disassembly.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 50 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other components. Detailed illustrations accompany each step. Safety warnings are provided to properly release spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 50 steps to fully disassemble the transmission, including removing gears, shafts, housings, seals, and other components. Detailed illustrations accompany each step. Safety warnings are provided to properly release spring forces. Required tools include link brackets, drivers, and bearing pullers.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing housing components, shafts, gears, seals, springs, and sensors. Detailed illustrations accompany each step to show how to remove specific parts. Safety precautions are provided, and all necessary tools are listed at the beginning.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing housing components, shafts, gears, seals, springs, and sensors. Detailed illustrations accompany each step to show how to remove specific parts. Safety precautions are provided, and all necessary tools are listed. The goal is to disassemble the entire transmission down to individual parts for repair or replacement.
This document provides disassembly instructions for the planetary transmission of a 972H wheel loader. It lists 50 steps to fully disassemble the transmission, including removing housing components, clutches, gears, shafts, seals and other internal parts. Detailed illustrations accompany each step to show how to remove each component. Safety precautions are provided, and all necessary tools are listed at the beginning.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, shafts, gears, seals, springs, and other internal parts. Detailed illustrations accompany each step to show how to remove each component. Safety precautions are provided, and all necessary tools are listed at the beginning. The overall process dismantles the entire transmission down to its individual parts.
This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and sensors. Precision tools are required and care must be taken due to heavy component weights and stored spring energies. Detailed illustrations accompany each step to ensure correct part identification and procedure.
Similar to Caterpillar Cat 972G II Wheel Loader (Prefix AXC) Service Repair Manual (AXC00001 and up).pdf (13)
Kubota B1710D Tractor Parts Catalogue Manual (Publishing ID BKIDK0391).pdfjnnfnjsdnnd
This document provides a parts list for frequently used engine parts. It includes the part number, name in Polish and English, quantity, serial number, weight, and remarks for each part. Common parts listed include starters, switches, fuses, filters, gaskets, bolts, and more. The document is published by Kubota and copyrighted for 2015.
Kubota B1700-HD Tractor Parts Catalogue Manual (Publishing ID BKIDA0020).pdfjnnfnjsdnnd
This document provides a parts list for a Kubota B1700-HD engine, including the crankcase, oil pan, cylinder head, gear case, and head cover. It lists 170 part numbers, part names in Polish and English, quantities, serial numbers if applicable, weights in kg, and other remarks. The parts list is divided into sections for the main engine components and subsections for individual parts within each component.
Volvo EC55-2 Compact Excavator Parts Catalogue Manual – SN 5001 - 7620.pdfjnnfnjsdnnd
This document contains specifications for various engine parts for a Volvo EC55-2 engine. It includes sections for the engine, cylinder head, valves, pistons, connecting rods, camshaft, and other components. Each section lists the relevant part numbers, descriptions, quantities, and other details. The document provides an extensive catalogue of replacement parts for this engine model.
Kubota B1241D-EC-F2-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA516...jnnfnjsdnnd
This document provides a parts list for frequently used items and their information. It includes 30 parts ranging from switches and fuses to hoses and filters. Each part is listed with its number, name in Polish and English, quantity, and other identifying information like serial number and weight. The document is copyrighted by KUBOTA in 2015.
Kubota B1700D Tractor Parts Catalogue Manual (Publishing ID BKIDK0093).pdfjnnfnjsdnnd
This document provides a parts list for a crankcase (Kurbelgehäuse) with part numbers, names, quantities, serial numbers, and other details. It lists over 200 individual part numbers. The parts are for various engine components, including the crankcase, oil pan, cylinder head, gear case, and head cover.
Kubota B1181DT-F2-EC-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA51...jnnfnjsdnnd
This document provides a parts list for the main bearing case of an engine. It includes the part numbers, names, quantities, and other details for over 20 parts that make up the main bearing case assembly. Key components listed include the main bearing case group, bearing case cover, oil seal, gaskets, bolts, and bearing shells. The document also provides copyright information at the bottom of each page.
Kubota B1241D-EC-F Tractor Parts Catalogue Manual (Publishing ID BKIDA5131).pdfjnnfnjsdnnd
This document provides a list of parts for an engine. It includes the part numbers, names in Polish and English, quantities, and other specifications for 230 different engine parts organized into categories like crankcase, oil pan, cylinder head, gear case, and head cover. The parts range from bolts, nuts, and plugs to larger assemblies and components like the crankcase, cylinder head, and gear case.
Kubota B1181D-EC Tractor Parts Catalogue Manual (Publishing ID BKIDA5129).pdfjnnfnjsdnnd
This document provides a parts list for a Kubota engine. It includes 230 parts ranging from starters, switches, fuses, filters, hoses, belts, and other engine components. Each part is listed with the part number, name in Polish and English, quantity, serial number if applicable, weight, and any remarks. It appears to be a comprehensive listing of components for a Kubota engine.
Kubota B1121D-F2-EC-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA515...jnnfnjsdnnd
This document provides a parts list for the main bearing case of an engine. It includes the part numbers, names, quantities, and other details for over 100 individual parts that make up the main bearing case assembly. The parts include the main bearing case group, bolts, pins, seals, gaskets, covers, and bearings.
Kubota B1161D-F2-EC-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA515...jnnfnjsdnnd
This document provides a list of parts for a Kubota engine crankcase assembly. It includes 140 individual parts with information on part numbers, names, quantities, and other specifications. The crankcase assembly consists of a composite crankcase component as the main part, along with various caps, plugs, pins, bolts, and other fittings that make up the full assembly. Safety precautions are noted for proper handling of the engine parts.
Kubota B1161D-EC Tractor Parts Catalogue Manual (Publishing ID BKIDA5128).pdfjnnfnjsdnnd
This document provides a parts list for a Kubota engine. It includes 230 parts ranging from starters, switches, fuses, filters, hoses, belts, and other engine components. Each part is listed with the part number, name in Polish and English, quantity, serial number if applicable, weight, and any remarks. This extensive list details all replacement parts for the engine.
Kubota B1121D-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA5156).pdfjnnfnjsdnnd
This document contains parts information for a Kubota engine, including the part numbers, names, quantities, and weights of various engine components. It lists 190 line items of parts organized into categories like crankcase, oil pan, cylinder head, gear case, and more. The document is in two languages, with the part names listed in both Polish and English.
Kubota B1121D-EC Tractor Parts Catalogue Manual (Publishing ID BKIDA5127).pdfjnnfnjsdnnd
This document provides a parts list for an engine. It includes 260 parts related to the engine, such as the crankcase, cylinder head, oil pan, gear case, and more. Each part is listed with its number, name in Polish and English, quantity, and other specifications. It appears to be a comprehensive listing of engine parts for reference when maintaining or repairing the engine.
Kubota B1121D Tractor Parts Catalogue Manual (Publishing ID BKIDA5126).pdfjnnfnjsdnnd
This document contains parts information for a Kubota engine. It lists 190 parts in the engine's crankcase, oil pan, cylinder head, gear case, head cover, oil filter, dipstick/guide, and oil pump systems. The parts are identified by number, name in Polish and English, quantity, and other specifications. Kubota claims copyright of the document from 2015.
The document provides instructions for removing the planetary carrier from the final drive of a D9R track-type tractor. It describes:
1) Removing the axles, cover, and bolts to access the carrier.
2) Using an adapter tool to lift the carrier out of the final drive hub.
3) Removing the sun gear from the carrier.
It then provides detailed steps and illustrations for safely removing and installing the carrier while supporting the surrounding components.
The document provides instructions for disassembling and assembling the final drive of a D7R track-type tractor. It lists 30 steps for disassembly, including removing gears, shafts, bearings and seals. It also lists 25 steps for assembly, installing components in reverse order and noting proper alignment and clearance measurements. Required specialized tools are listed for various removal and installation tasks.
This document provides instructions for installing and removing various components of a Caterpillar 3412E engine, including:
1) Installing the aftercooler housing and core on a 3408E/3412E engine.
2) Removing and installing the front engine support on a 3408E/3412E engine.
3) Removing the rear gear group from a 3408E/3412E engine, which involves disassembling various gears, bearings, and shafts.
4) Installing the rear gear group on a 3408E/3412E engine, which involves assembling the various gears, bearings, and shafts.
The document provides instructions for removing and installing a cylinder head on a Caterpillar D9N track-type tractor powered by a 3408 engine. It describes:
1) Removing hoses, tubes, bolts and the fuel manifold to access the cylinder head.
2) Attaching lifting tools and removing the cylinder head, which weighs approximately 90-172 kg depending on the engine model.
3) Cleaning and inspecting parts, applying a new gasket and reinstalling the cylinder head along with associated components like seals and bolts. Tightening bolts in a specific sequence is emphasized.
The document provides instructions for removing, disassembling, and installing a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then removing the compression brake by lifting it out while holding the oil tube. It also details disassembling the compression brake by removing pistons, springs, seals and other components. The assembly process is described as well, including installing new seals and pistons before reinstalling the compression brake.
The document provides instructions for disassembling a steering planetary and brake assembly. Key steps include:
1. Removing the final drive, planetary group, and brake assembly from the machine.
2. Separating the planetary group and brake assembly from the final drive hub using lifting brackets and forcing bolts.
3. Further disassembling the planetary group and brake assembly by removing housing components like ring gears, plates, and carriers to access internal parts like gears, shafts, pins, and seals.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G II WHEEL LOADER AXC
Configuration: 972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
966G Series II and 972G Series II
Wheel Loaders Power Train
Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008
i02299775
Transmission Planetary - Disassemble
SMCS - 3160-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
C 8H-0663 Bearing Puller 1
Start By:
A. Separate the transmission from the output transfer gears. Refer to Disassembly and
Assembly, "Transmission from Output Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00458960
1. Remove O-ring seal (1) from the housing.
2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft.
Illustration 2 g00459007
3. Remove plate (5) .
Illustration 3 g00459030
2/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Attach Tooling (A) and a suitable lifting device to the transmission, as shown. The weight
of the transmission is approximately 544 kg (1200 lb).
5. Carefully position the planetary group on the opposite end so that No. 6 clutch housing (6)
is facing upward, as shown.
Illustration 4 g00459073
6. Remove retaining ring (8) from output shaft (7) .
Illustration 5 g00459075
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Remove bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolts.
Illustration 6 g00459079
8. Remove clutch piston (10) from No. 6 clutch housing (6) .
9. Remove seal rings (11) and (12) from clutch piston (10) .
Illustration 7 g00459087
10. Remove clutch plate (14) and springs (13) .
4/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00459138
14. Remove metal seal ring (20) from carrier assembly (19) .
Illustration 12 g00459150
15. Use a hammer and a punch to push the spring pins through carrier assembly (19) and into
planetary shafts (21) .
6/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00459151
16. Use a hammer and a punch to remove planetary shafts (21) from carrier assembly (19) .
Illustration 14 g00324725
17. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly.
Remove spring pins (25) from planetary shafts (21) .
Illustration 15 g00459161
18. Remove O-ring seal (26). Remove bolts (27) from manifold (28) .
7/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00565113
19. Disconnect the harness assemblies which are attached to transmission modulating valves
(29). Remove transmission modulating valves (29) from the transmission housing.
Illustration 17 g00459316
20. Remove retaining ring (32) and gear (30). Remove retaining ring (31) .
Illustration 18 g00459322
8/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 21. Use Tooling (A) and a suitable lifting device to remove manifold (28). The weight of
manifold (28) is approximately 85 kg (190 lb).
22. Remove bolt (33) which holds the harness assembly in place.
Illustration 19 g00459352
23. Remove retaining ring (34) and bearing (35) from manifold (28) .
Illustration 20 g00459369
24. Remove retaining ring (36) and clutch housing (37) .
9/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00459372
25. Remove O-ring seal (38) from clutch housing (37) .
Illustration 22 g00459375
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Use steel spacers and a suitable press to push on retainer plate (40). Remove retaining ring
(39) from the clutch housing.
10/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00459387
27. Separate retaining ring (39), retainer plate (40), three coned disc springs (41), and clutch
piston (42) .
Illustration 24 g00459393
28. Remove seal rings (43) from clutch piston (42) .
Illustration 25 g00459394
11/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 29. Remove seal rings (44) from clutch housing (37) .
Illustration 26 g00565119
30. Remove retaining ring (45) from the output shaft. Remove hub (46) .
Illustration 27 g00565685
31. Remove friction discs (47) and clutch plates (48) .
12/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g00565132
32. Remove clutch plate (49) and ring gear (50) .
Illustration 29 g00565193
33. Remove springs (51). Remove friction discs (52) and clutch plates (53) .
Illustration 30 g00565687
34. Remove clutch piston (54). Remove O-ring seals (55) and (56) .
13/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 31 g00459506
35. Remove seal rings (57) and (58) from clutch piston (54) .
Illustration 32 g00565199
36. Use Tooling (A) and a suitable lifting device to remove housing (59). The weight of housing
(59) is approximately 66 kg (145 lb).
Note: The clutch piston may be stuck in housing (59). As housing (59) is removed, the
clutch piston may fall.
14/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 33 g00565203
37. Remove clutch piston (60) .
Illustration 34 g00459540
38. Remove seal rings (61) and (62) from clutch piston (60) .
Illustration 35 g00565255
39. Remove friction discs (63) and clutch plates (64) .
15/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 36 g00565689
40. Remove O-ring seals (65) and (66). Remove springs (68) and carrier assembly (69).
Remove rods (67) .
Illustration 37 g00459619
41. Remove gear (70) from carrier assembly (69) .
Illustration 38 g00459622
16/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 42. Remove retaining ring (71) and bearing (72) .
Illustration 39 g00459634
43. Use several small steel rods (73) (3.175 mm (0.1250 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (69) to ring gear (74) .
44. Remove carrier assembly (69) from ring gear (74) .
Illustration 40 g00459638
45. Remove retaining ring (75) from carrier assembly (69) .
17/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 41 g00459643
46. Use a hammer and a punch to push the spring pins through carrier assembly (69) and into
planetary shafts (76) .
47. Use a hammer and a punch to remove planetary shafts (76) from carrier assembly (69) .
Illustration 42 g00459646
48. Remove thrust discs (77), planetary gears (78), and bearings (79) from the carrier assembly.
Remove spring pins (80) from planetary shafts (76) .
18/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 43 g00565272
49. Remove retaining ring (81) that holds output shaft (82) to the input shaft. Remove output
shaft (82) .
Illustration 44 g00459776
50. Remove O-ring seal (83) from output shaft (82) .
Illustration 45 g00460029
51. Remove retaining ring (85) .
52. Remove sun gear (84) from output shaft (82) .
19/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 46 g00460030
53. Use a suitable press to push output shaft (82) out of bearing (86), as shown.
Illustration 47 g00460034
54. If necessary, remove bearings (87) from both ends of output shaft (82) .
Illustration 48 g00565282
20/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 55. Use Tooling (A) and a suitable lifting device to remove housing (88). The weight of housing
(88) is approximately 61 kg (135 lb).
Illustration 49 g00460042
56. Remove clutch piston (89), friction discs (90), and clutch plates (91) .
Illustration 50 g00460045
57. Remove seal rings (92) and (93) from clutch piston (89) .
21/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 51 g00460067
58. Remove retaining ring (94) from the input shaft.
59. Remove springs (95) and ring gear (96). Remove O-ring seals (97) and (98) .
Illustration 52 g00460068
60. Remove carrier assembly (99) from the input shaft. The weight of the carrier assembly is
approximately 29 kg (65 lb).
22/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 53 g00460074
61. Remove gear (100) .
62. Place a suitable wood block under carrier assembly (99) .
63. Use several small steel rods (101) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (99) to ring gear (102) together.
64. Remove ring gear (102) from carrier assembly (99) .
Illustration 54 g00460078
65. Remove retaining ring (105) from carrier assembly (99) .
66. Remove retaining ring (104). Remove sun gear (103) and the bearing. Use Tooling (B) to
remove sun gear (103) and the bearing.
Illustration 55 g00460081
67. Use a hammer and a punch to push the spring pins through carrier assembly (99) and into
planetary shafts (106) .
23/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 56 g00460134
68. Use a hammer and a punch to remove planetary shafts (106) from carrier assembly (99) .
Illustration 57 g00460135
69. Remove thrust discs (107), bearings (109), and planetary gears (108) from the carrier
assembly.
70. Remove spring pins (110) from planetary shafts (106) .
24/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 58 g00460138
71. Remove bearing (111) from sun gear (103) .
Illustration 59 g00460141
72. Remove O-ring seal (112) from sun gear (103) .
Illustration 60 g00460178
73. Remove plate (113) .
25/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 61 g00460181
74. Remove friction discs (114) and clutch plates (117). Remove O-ring seals (115) and (116) .
Illustration 62 g00460207
75. Use several small steel rods (118) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds coupling (120) to carrier assembly (119). Remove
coupling (120) from carrier assembly (119) .
Note: Coupling (120) and carrier assembly (119) may be removed together at this time. Use
small steel rods (118) in order to separate coupling (120) and carrier assembly (119). See
Step 43 for similar actions.
26/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 63 g00460208
76. Remove clutch piston (121) from the clutch housing. Remove carrier assembly (119) .
Illustration 64 g00460209
77. Remove seal rings (122) and (123) from clutch piston (121) .
Illustration 65 g00460233
78. Remove retaining ring (124). Use Tooling (B) to remove bearing (125) .
27/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 79. Remove seal ring (126) from carrier assembly (119) .
Illustration 66 g00460237
80. Use a hammer and a punch to push the spring pins through carrier assembly (119) and into
planetary shafts (127) .
81. Use a hammer and a punch to remove planetary shafts (127) from carrier assembly (119) .
Illustration 67 g00460313
82. Remove thrust discs (128), planetary gears (129), and bearings (130) from the carrier
assembly. Remove spring pins (131) from planetary shafts (127) .
28/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 68 g00460315
83. Remove retaining ring (132) from housing (133) .
84. Use a soft hammer to remove input shaft (134) from housing (133) .
Illustration 69 g00460318
85. Remove ring seals (136) and O-ring seal (137) from input shaft (134). Remove bearing
(135) .
29/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 70 g00460322
86. Use a suitable press and Tooling (C) to remove race (138) from input shaft (134) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 11 10:16:56 UTC+0800 2021
30/30
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G II WHEEL LOADER AXC
Configuration: 972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
966G Series II and 972G Series II
Wheel Loaders Power Train
Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008
i06064263
Transmission Planetary - Assemble
SMCS - 3160-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
D FT-2746 Guide Pin 2
E 1P-0510 Driver Gp 1
F - Loctite 5127 1
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in cleaning
fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts.
1/31
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 1 g00460318
Note: O-ring seal (137) is not installed at this time. The O-ring seal is shown in order to
clarify the installation in Step 11.
1. Raise the temperature of bearing (135) and the race. Install bearing (135) and the race onto
input shaft (134) , as shown.
2. Apply clean transmission oil to ring seals (136) . Install two ring seals (136) on input shaft
(134) .
Illustration 2 g00460315
3. Carefully install input shaft (134) in housing (133) .
4. Install retaining ring (132) in order to hold the input shaft and the bearing in place.
2/31
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
35. Illustration 3 g00460313
Illustration 4 g00460237
5. Install bearings (130) in planetary gears (129) . Install the gear assemblies, thrust discs
(128) , and planetary shafts (127) in carrier assembly (119) .
6. Use a hammer and a punch to install spring pins (131) that hold planetary shafts (127) in
carrier assembly (119) . Make sure that the spring pins are flush with the counterbore in the
carrier.
Illustration 5 g00460233
3/31
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. 7. Install seal ring (126) on carrier assembly (119) .
8. Use Tooling (B) to install bearing (125) . Install retaining ring (124) .
Note: Coupling (120) may be installed on carrier assembly (119) at this time. Refer to Step
13 for the procedure.
Illustration 6 g00460209
9. Install seal rings (122) and (123) on clutch piston (121) .
Illustration 7 g00460208
10. Place suitable cribbing under the housing. Install clutch piston (121) in the clutch housing.
Make sure that the lips of the seals are facing downward.
11. Install O-ring seal (137) . Apply clean transmission oil to O-ring seal (137) and the O-ring
seal groove on the shaft. Refer to Illustration 1 for the location of the O-ring seal.
12. Install carrier assembly (119) .
4/31
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
37. Illustration 8 g00460207
13. If necessary, install coupling (120) on carrier assembly (119) . Use small steel rods (118) to
compress the retaining ring that holds coupling (120) to carrier assembly (119) .
Illustration 9 g00460934
Illustration 10 g00720054
Note: For assembly purposes, use Tooling (D) to hold the clutch plates in place. Do not
remove Tooling (D) until Step 85 is completed.
5/31
972G II Wheel Loader AXC00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...