This document provides disassembly instructions for the transmission planetary system of a 972H wheel loader. It lists over 60 steps to fully disassemble the transmission, including removing housing components, clutches, gears, carriers, shafts, seals and other parts. Detailed illustrations accompany each step. Safety warnings are provided to remove parts carefully and wear protective equipment when releasing spring forces. Required tools include link brackets, drivers, and bearing pullers.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972H WHEEL LOADER A7G
Configuration: 972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
966H and 972H Wheel Loaders Power Train
Media Number -RENR8847-07 Publication Date -01/03/2013 Date Updated -04/03/2013
i02299775
Transmission Planetary - Disassemble
SMCS - 3160-015
S/N - A7D1-UP
S/N - A7G1-UP
S/N - A7J1-UP
S/N - GTA1-UP
S/N - LCC1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
C 8H-0663 Bearing Puller 1
Start By:
A. Separate the transmission from the output transfer gears. Refer to Disassembly and
Assembly, "Transmission from Output Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
Illustration 1 g00458960
1. Remove O-ring seal (1) from the housing.
2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft.
Illustration 2 g00459007
3. Remove plate (5) .
2/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00459030
4. Attach Tooling (A) and a suitable lifting device to the transmission, as shown. The weight
of the transmission is approximately 544 kg (1200 lb).
5. Carefully position the planetary group on the opposite end so that No. 6 clutch housing (6)
is facing upward, as shown.
Illustration 4 g00459073
6. Remove retaining ring (8) from output shaft (7) .
3/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 5 g00459075
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolts.
Illustration 6 g00459079
8. Remove clutch piston (10) from No. 6 clutch housing (6) .
9. Remove seal rings (11) and (12) from clutch piston (10) .
4/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g00459133
13. Remove carrier assembly (19) .
Illustration 11 g00459138
14. Remove metal seal ring (20) from carrier assembly (19) .
Illustration 12 g00459150
6/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. 15. Use a hammer and a punch to push the spring pins through carrier assembly (19) and into
planetary shafts (21) .
Illustration 13 g00459151
16. Use a hammer and a punch to remove planetary shafts (21) from carrier assembly (19) .
Illustration 14 g00324725
17. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly.
Remove spring pins (25) from planetary shafts (21) .
7/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 15 g00459161
18. Remove O-ring seal (26). Remove bolts (27) from manifold (28) .
Illustration 16 g00565113
19. Disconnect the harness assemblies which are attached to transmission modulating valves
(29). Remove transmission modulating valves (29) from the transmission housing.
Illustration 17 g00459316
8/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. 20. Remove retaining ring (32) and gear (30). Remove retaining ring (31) .
Illustration 18 g00459322
21. Use Tooling (A) and a suitable lifting device to remove manifold (28). The weight of
manifold (28) is approximately 85 kg (190 lb).
22. Remove bolt (33) which holds the harness assembly in place.
Illustration 19 g00459352
23. Remove retaining ring (34) and bearing (35) from manifold (28) .
9/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 20 g00459369
24. Remove retaining ring (36) and clutch housing (37) .
Illustration 21 g00459372
25. Remove O-ring seal (38) from clutch housing (37) .
Illustration 22 g00459375
10/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Use steel spacers and a suitable press to push on retainer plate (40). Remove retaining ring
(39) from the clutch housing.
Illustration 23 g00459387
27. Separate retaining ring (39), retainer plate (40), three coned disc springs (41), and clutch
piston (42) .
Illustration 24 g00459393
11/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 28. Remove seal rings (43) from clutch piston (42) .
Illustration 25 g00459394
29. Remove seal rings (44) from clutch housing (37) .
Illustration 26 g00565119
30. Remove retaining ring (45) from the output shaft. Remove hub (46) .
12/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 30 g00565687
34. Remove clutch piston (54). Remove O-ring seals (55) and (56) .
Illustration 31 g00459506
35. Remove seal rings (57) and (58) from clutch piston (54) .
Illustration 32 g00565199
14/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 36. Use Tooling (A) and a suitable lifting device to remove housing (59). The weight of housing
(59) is approximately 66 kg (145 lb).
Note: The clutch piston may be stuck in housing (59). As housing (59) is removed, the
clutch piston may fall.
Illustration 33 g00565203
37. Remove clutch piston (60) .
Illustration 34 g00459540
38. Remove seal rings (61) and (62) from clutch piston (60) .
15/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 41. Remove gear (70) from carrier assembly (69) .
Illustration 38 g00459622
42. Remove retaining ring (71) and bearing (72) .
Illustration 39 g00459634
43. Use several small steel rods (73) (3.175 mm (0.1250 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (69) to ring gear (74) .
44. Remove carrier assembly (69) from ring gear (74) .
17/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 40 g00459638
45. Remove retaining ring (75) from carrier assembly (69) .
Illustration 41 g00459643
46. Use a hammer and a punch to push the spring pins through carrier assembly (69) and into
planetary shafts (76) .
47. Use a hammer and a punch to remove planetary shafts (76) from carrier assembly (69) .
18/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 42 g00459646
48. Remove thrust discs (77), planetary gears (78), and bearings (79) from the carrier assembly.
Remove spring pins (80) from planetary shafts (76) .
Illustration 43 g00565272
49. Remove retaining ring (81) that holds output shaft (82) to the input shaft. Remove output
shaft (82) .
Illustration 44 g00459776
50. Remove O-ring seal (83) from output shaft (82) .
19/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 45 g00460029
51. Remove retaining ring (85) .
52. Remove sun gear (84) from output shaft (82) .
Illustration 46 g00460030
53. Use a suitable press to push output shaft (82) out of bearing (86), as shown.
Illustration 47 g00460034
20/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 54. If necessary, remove bearings (87) from both ends of output shaft (82) .
Illustration 48 g00565282
55. Use Tooling (A) and a suitable lifting device to remove housing (88). The weight of housing
(88) is approximately 61 kg (135 lb).
Illustration 49 g00460042
56. Remove clutch piston (89), friction discs (90), and clutch plates (91) .
21/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 50 g00460045
57. Remove seal rings (92) and (93) from clutch piston (89) .
Illustration 51 g00460067
58. Remove retaining ring (94) from the input shaft.
59. Remove springs (95) and ring gear (96). Remove O-ring seals (97) and (98) .
Illustration 52 g00460068
22/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. 60. Remove carrier assembly (99) from the input shaft. The weight of the carrier assembly is
approximately 29 kg (65 lb).
Illustration 53 g00460074
61. Remove gear (100) .
62. Place a suitable wood block under carrier assembly (99) .
63. Use several small steel rods (101) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds carrier assembly (99) to ring gear (102) together.
64. Remove ring gear (102) from carrier assembly (99) .
Illustration 54 g00460078
65. Remove retaining ring (105) from carrier assembly (99) .
66. Remove retaining ring (104). Remove sun gear (103) and the bearing. Use Tooling (B) to
remove sun gear (103) and the bearing.
23/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 55 g00460081
67. Use a hammer and a punch to push the spring pins through carrier assembly (99) and into
planetary shafts (106) .
Illustration 56 g00460134
68. Use a hammer and a punch to remove planetary shafts (106) from carrier assembly (99) .
Illustration 57 g00460135
24/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. 69. Remove thrust discs (107), bearings (109), and planetary gears (108) from the carrier
assembly.
70. Remove spring pins (110) from planetary shafts (106) .
Illustration 58 g00460138
71. Remove bearing (111) from sun gear (103) .
Illustration 59 g00460141
72. Remove O-ring seal (112) from sun gear (103) .
25/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 75. Use several small steel rods (118) (2.36 mm (0.093 inch) diameter and one pointed tip) to
compress the retaining ring that holds coupling (120) to carrier assembly (119). Remove
coupling (120) from carrier assembly (119) .
Note: Coupling (120) and carrier assembly (119) may be removed together at this time. Use
small steel rods (118) in order to separate coupling (120) and carrier assembly (119). See
Step 43 for similar actions.
Illustration 63 g00460208
76. Remove clutch piston (121) from the clutch housing. Remove carrier assembly (119) .
Illustration 64 g00460209
77. Remove seal rings (122) and (123) from clutch piston (121) .
27/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 65 g00460233
78. Remove retaining ring (124). Use Tooling (B) to remove bearing (125) .
79. Remove seal ring (126) from carrier assembly (119) .
Illustration 66 g00460237
80. Use a hammer and a punch to push the spring pins through carrier assembly (119) and into
planetary shafts (127) .
81. Use a hammer and a punch to remove planetary shafts (127) from carrier assembly (119) .
28/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
30. Illustration 67 g00460313
82. Remove thrust discs (128), planetary gears (129), and bearings (130) from the carrier
assembly. Remove spring pins (131) from planetary shafts (127) .
Illustration 68 g00460315
83. Remove retaining ring (132) from housing (133) .
84. Use a soft hammer to remove input shaft (134) from housing (133) .
29/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
31. Illustration 69 g00460318
85. Remove ring seals (136) and O-ring seal (137) from input shaft (134). Remove bearing
(135) .
Illustration 70 g00460322
86. Use a suitable press and Tooling (C) to remove race (138) from input shaft (134) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon May 3 13:54:23 UTC+0800 2021
30/30
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
32. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972H WHEEL LOADER A7G
Configuration: 972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
966H and 972H Wheel Loaders Power Train
Media Number -RENR8847-07 Publication Date -01/03/2013 Date Updated -04/03/2013
i06064263
Transmission Planetary - Assemble
SMCS - 3160-016
S/N - A7D1-UP
S/N - A7G1-UP
S/N - A7J1-UP
S/N - GTA1-UP
S/N - LCC1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
D FT-2746 Guide Pin 2
E 1P-0510 Driver Gp 1
F - Loctite 5127 1
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in cleaning
fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be
deposited on the parts.
1/31
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
33. Illustration 1 g00460318
Note: O-ring seal (137) is not installed at this time. The O-ring seal is shown in order to
clarify the installation in Step 11.
1. Raise the temperature of bearing (135) and the race. Install bearing (135) and the race onto
input shaft (134) , as shown.
2. Apply clean transmission oil to ring seals (136) . Install two ring seals (136) on input shaft
(134) .
Illustration 2 g00460315
3. Carefully install input shaft (134) in housing (133) .
4. Install retaining ring (132) in order to hold the input shaft and the bearing in place.
2/31
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
34. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
35. Illustration 3 g00460313
Illustration 4 g00460237
5. Install bearings (130) in planetary gears (129) . Install the gear assemblies, thrust discs
(128) , and planetary shafts (127) in carrier assembly (119) .
6. Use a hammer and a punch to install spring pins (131) that hold planetary shafts (127) in
carrier assembly (119) . Make sure that the spring pins are flush with the counterbore in the
carrier.
Illustration 5 g00460233
3/31
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
36. 7. Install seal ring (126) on carrier assembly (119) .
8. Use Tooling (B) to install bearing (125) . Install retaining ring (124) .
Note: Coupling (120) may be installed on carrier assembly (119) at this time. Refer to Step
13 for the procedure.
Illustration 6 g00460209
9. Install seal rings (122) and (123) on clutch piston (121) .
Illustration 7 g00460208
10. Place suitable cribbing under the housing. Install clutch piston (121) in the clutch housing.
Make sure that the lips of the seals are facing downward.
11. Install O-ring seal (137) . Apply clean transmission oil to O-ring seal (137) and the O-ring
seal groove on the shaft. Refer to Illustration 1 for the location of the O-ring seal.
12. Install carrier assembly (119) .
4/31
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
37. Illustration 8 g00460207
13. If necessary, install coupling (120) on carrier assembly (119) . Use small steel rods (118) to
compress the retaining ring that holds coupling (120) to carrier assembly (119) .
Illustration 9 g00460934
Illustration 10 g00720054
Note: For assembly purposes, use Tooling (D) to hold the clutch plates in place. Do not
remove Tooling (D) until Step 85 is completed.
5/31
972H Wheel Loader A7G00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2021/5/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...