1. The document provides disassembly and assembly instructions for a freewheel stator in the torque converter of a Caterpillar 972G II wheel loader.
2. It describes 34 steps to disassemble components such as the torque converter housing, impeller, stator, carrier shaft, and turbine.
3. The 19-step assembly section instructs technicians to thoroughly clean all parts, install components like the bearing, seals, and retaining rings in the correct order, and torque bolts to the specified values. Proper cleaning and installation order are emphasized.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G II WHEEL LOADER ANY
Configuration: 972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
966G Series II and 972G Series II
Wheel Loaders Power Train
Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008
i02299289
Torque Converter (Freewheel Stator) - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output transfer gears.
Refer to Disassembly and Assembly, "Torque Converter from Transmission, Output
Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00456063
1. Use Tooling (A) and a suitable lifting device to position the torque converter assembly on
suitable blocking, as shown. The weight of the torque converter assembly is approximately
191 kg (420 lb).
Illustration 2 g00563249
2. Remove torque converter speed sensor (4) , the seal, and the washer.
3. Remove bolt (1) and retainer (2) . Remove gear (3) from the torque converter housing.
2/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00563276
4. Remove bolts (6) and the washers that hold the torque converter to the torque converter
housing.
5. Remove O-ring seal (5) .
Illustration 4 g00456148
6. Remove bolts (7) and pump drive flange (8) .
3/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00456168
7. Remove bolt (9) and the washer that holds drive gear shaft (10) to the torque converter
housing.
8. Remove pump drive gear (11) and drive gear shaft (10) .
9. Remove drive gear shaft (10) from pump drive gear (11) .
Illustration 6 g00456172
10. Use Tooling (A) and a suitable lifting device to remove the torque converter housing. The
weight of the torque converter housing is approximately 113 kg (250 lb).
Illustration 7 g00456176
11. Remove bearing (12) from pump drive gear (11) . Use Tooling (B) in order to remove the
bearing.
4/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01152648
Note: For the disassembly of carrier shaft (17) , refer to Steps 30 through 34.
12. Remove bolts (13) and the washers. Use a suitable lifting device to remove impeller (14)
from rotating housing (15) . The weight of the impeller assembly is approximately 36 kg (80
lb).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 13
through 19.
Illustration 9 g00878581
13. Turn impeller (14) to the opposite side.
14. Remove retaining ring (16) and spacer (18) from carrier shaft (17) .
15. Remove stator (19) .
5/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00878584
16. Remove retaining ring (20) and washer (21) from stator (19) . Repeat the procedure for the
opposite side of stator (19) .
Illustration 11 g00878585
Note: If necessary, raise the temperature of the stator to a maximum temperature of 135 °C
(275 °F) for approximately fifteen minutes.
17. Remove bearing race (22) , freewheel rollers (23) , freewheel springs (24) , and freewheel
cam (25) from stator (19) .
6/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00878606
18. Remove spacer (26) from impeller (14) .
Illustration 13 g00878607
19. Use a suitable press to remove carrier shaft (17) from impeller (14) .
Illustration 14 g00878778
20. Remove bolts (27) and drive gear (28) .
7/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00878780
21. Remove bearing (29) from impeller (14) .
Illustration 16 g00878781
22. Remove retaining ring (30) and end cover (31) from rotating housing (15) .
8/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00878783
23. Remove O-ring seal (32) .
24. Use Tooling (C) to remove retaining ring (33) .
25. Remove bearing spacer (34) from rotating housing (15) .
Illustration 18 g00878784
26. Turn rotating housing (15) onto the opposite side. Remove turbine (35) .
Illustration 19 g00878808
27. Remove bolts (36) and the washers. Separate turbine (35) from turbine hub assembly (37) .
28. If necessary, remove locating dowel (38) .
9/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 20 g00878809
29. Remove bearing (39) and ring (40) from rotating housing (15) .
Illustration 21 g01152618
30. Remove retaining ring (46) and plate (45) .
31. Use a soft faced hammer to remove shaft assembly (41) from carrier shaft (17) .
32. Remove outer bearing (44) .
33. Use a suitable press to remove inner race (43) from shaft (41) .
10/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 34. Remove ring (42 ) from shaft (41) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 15 11:23:27 UTC+0800 2021
11/11
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G II WHEEL LOADER ANY
Configuration: 972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
966G Series II and 972G Series II
Wheel Loaders Power Train
Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008
i07399197
Torque Converter (Freewheel Stator) - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 1P-0510 Driver Gp 1
C 2P-8312 Retaining Ring Pliers 1
D 7F-6068 Sleeve 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00878809
1. Install bearing (39) and ring (40) on rotating housing (15).
Illustration 2 g00878808
1. Install locating dowel (38) in turbine hub assembly (37).
2. Install turbine hub assembly (37) to turbine (35). Install bolts (36) and the washers. The
torque for bolts (36) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00878784
3. Turn rotating housing (15) onto opposite side. Install turbine (35).
2/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g00878783
4. Install bearing spacer (34).
5. Use Tooling (C) to install retaining ring (33) on turbine hub assembly (37). Retaining ring
(33) must be securely seated in the groove.
6. Install O-ring seal (32).
Illustration 5 g00878781
7. Install end cover (31) and retaining ring (30) in rotating housing (15).
3/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g00878780
8. Lower the temperature of bearing (29).
9. Install bearing (29) in impeller (14).
Note: The notch in bearing (29) must face downward, as shown.
Illustration 7 g00878778
10. Install drive gear (28) and bolts (27). The torque for bolts (27) is 105 ± 15 N·m
(75 ± 11 lb ft).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 11
through 16.
Illustration 8 g01151541
11. Install the seal ring (not shown) onto carrier shaft (17). Use a suitable press to install carrier
shaft (17) in impeller (14).
12. Install spacer (26) over shaft (17).
4/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g00878585
13. Install freewheel cam (25), freewheel springs (24), freewheel rollers (23), and bearing race
(22) in stator (19).
Note: If necessary, raise the temperature of stator (19) to a maximum temperature of 135 °C
(275 °F). Install the cam with the IMPELLER SIDE facing downward. Continue with the
installation until freewheel cam (25) contacts the retaining ring (not shown).
Note: Install freewheel springs (24) with the maximum number of loops toward the outside
diameter of freewheel cam (25).
Illustration 10 g00878584
14. Install washer (21) and retaining ring (20) on stator (19). Repeat the procedure for the
opposite side of stator (19).
5/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 11 g00878581
15. Install stator (19) on impeller (14).
16. Install plate (18) and retaining ring (16) on carrier shaft (17).
Illustration 12 g01152618
17. Assemble carrier shaft (17), as follows.
18. Install ring (42) on shaft (41).
19. Use a suitable press to install inner race (43) onto shaft (41).
20. Install outer bearing (44).
6/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 21. Use Tooling (B), Tooling (D), and a suitable press to install shaft assembly (41) and outer
bearing (44) into carrier shaft (17).
22. Install plate (45) and retaining ring (46).
Illustration 13 g00456243
23. Install impeller (14) on rotating housing (15). The weight of the impeller assembly is
approximately 36 kg (80 lb).
24. Install bolts (13) and the washers. The torque for bolts (13) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 14 g00456176
25. Use Tooling (B) to install bearing (12) in pump drive gear (11).
7/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00456168
Illustration 16 g00456172
26. Install pump drive gear (11) and drive gear shaft (10).
27. Use Tooling (A) and a suitable lifting device to install the torque converter housing over the
torque converter. The weight of the torque converter housing is approximately 113 kg
(250 lb).
28. Install bolt (9) and the washer that holds drive gear shaft (10) to the torque converter
housing. The torque for bolt (9) is 240 ± 40 N·m (180 ± 30 lb ft).
Illustration 17 g00456148
29. Install pump drive flange (8) and bolts (7). The torque for bolts (7) is 60 ± 12 N·m
(44 ± 9 lb ft).
8/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g00563276
30. Install bolts (6) and the washers that hold the torque converter to the torque converter
housing. The torque for bolts (6) is 50 ± 10 N·m (37 ± 7 lb ft).
31. Install O-ring seal (5).
Illustration 19 g00563249
32. Install gear (3), retainer (2), and bolt (1). The torque for bolt (1) is 120 ± 20 N·m
(90 ± 15 lb ft).
33. Install torque converter speed sensor (4), the seal, and the washer. Adjust torque converter
speed sensor (4) to maintain an air gap of 0.71 ± 0.18 mm (0.028 ± 0.007 inch). The torque
for torque converter speed sensor (4) is 25 ± 5 N·m (18 ± 4 lb ft).
End By:
a. Connect the torque converter to the transmission and to the output transfer gears. Refer to
Disassembly and Assembly, "Torque Converter to Transmission, Output Transfer Gears -
Connect".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 15 11:24:24 UTC+0800 2021
9/9
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G II WHEEL LOADER ANY
Configuration: 972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
966G Series II and 972G Series II
Wheel Loaders Power Train
Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008
i02642179
Transmission from Output Transfer Gears - Separate
SMCS - 3002-076
Separation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
Start By:
A. Separate the torque converter from the transmission. Refer to Disassembly and Assembly,
"Torque Converter from Transmission, Output Transfer Gears - Separate".
Note: Put identification marks on all harness assemblies for installation purposes. Plug all tube
assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the
system.
1/3
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g01325525
1. Remove bolts (1) and remove drain tube assembly (2) .
Illustration 2 g01325543
2. Attach Tooling (A) and a suitable lifting device to transmission planetary (4) .
3. Remove O-ring seal (3) .
Illustration 3 g01325555
2/3
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 4 g01325557
4. Disconnect harness assemblies (6). Disconnect harness assembly (8) .
5. Remove bolts (5) which hold transmission planetary (4) to output transfer gear case (7) .
Note: If necessary, use forcing screws in order to separate transmission planetary (4) from
output transfer gear case (7) .
6. Use Tooling (A) and the suitable lifting device in order to separate transmission planetary
(4) from output transfer gear case (7). The weight of transmission planetary (4) is
approximately 545 kg (1200 lb).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat May 15 11:25:21 UTC+0800 2021
3/3
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 972G II WHEEL LOADER ANY
Configuration: 972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine
Disassembly and Assembly
966G Series II and 972G Series II
Wheel Loaders Power Train
Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008
i02299775
Transmission Planetary - Disassemble
SMCS - 3160-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 1P-0520 Driver Gp 1
C 8H-0663 Bearing Puller 1
Start By:
A. Separate the transmission from the output transfer gears. Refer to Disassembly and
Assembly, "Transmission from Output Transfer Gears - Separate".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00458960
1. Remove O-ring seal (1) from the housing.
2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft.
Illustration 2 g00459007
3. Remove plate (5) .
Illustration 3 g00459030
2/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 4. Attach Tooling (A) and a suitable lifting device to the transmission, as shown. The weight
of the transmission is approximately 544 kg (1200 lb).
5. Carefully position the planetary group on the opposite end so that No. 6 clutch housing (6)
is facing upward, as shown.
Illustration 4 g00459073
6. Remove retaining ring (8) from output shaft (7) .
Illustration 5 g00459075
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 7. Remove bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolts.
Illustration 6 g00459079
8. Remove clutch piston (10) from No. 6 clutch housing (6) .
9. Remove seal rings (11) and (12) from clutch piston (10) .
Illustration 7 g00459087
10. Remove clutch plate (14) and springs (13) .
4/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 11 g00459138
14. Remove metal seal ring (20) from carrier assembly (19) .
Illustration 12 g00459150
15. Use a hammer and a punch to push the spring pins through carrier assembly (19) and into
planetary shafts (21) .
6/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
32. Illustration 13 g00459151
16. Use a hammer and a punch to remove planetary shafts (21) from carrier assembly (19) .
Illustration 14 g00324725
17. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly.
Remove spring pins (25) from planetary shafts (21) .
Illustration 15 g00459161
18. Remove O-ring seal (26). Remove bolts (27) from manifold (28) .
7/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 16 g00565113
19. Disconnect the harness assemblies which are attached to transmission modulating valves
(29). Remove transmission modulating valves (29) from the transmission housing.
Illustration 17 g00459316
20. Remove retaining ring (32) and gear (30). Remove retaining ring (31) .
Illustration 18 g00459322
8/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. 21. Use Tooling (A) and a suitable lifting device to remove manifold (28). The weight of
manifold (28) is approximately 85 kg (190 lb).
22. Remove bolt (33) which holds the harness assembly in place.
Illustration 19 g00459352
23. Remove retaining ring (34) and bearing (35) from manifold (28) .
Illustration 20 g00459369
24. Remove retaining ring (36) and clutch housing (37) .
9/30
972G II Wheel Loader ANY00001-UP (MACHINE) POWERED BY 3196 Engine(SE...
2021/5/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...