This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. The disassembly procedure involves over 40 steps to remove components like the transmission oil pump, torque converter speed sensor, bolts, shafts, bearings, seals, and impeller. The assembly procedure similarly involves over 25 steps but in reverse order to reinstall all components back into the torque converter housing. Precise alignment and torque specifications are noted throughout.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 5RS
Configuration: 962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHINE) POWERED BY 3126 ENGINE
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754103
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output gears. Refer to
Disassembly and Assembly, "Torque Converter from Transmission, Output Gears -
Separate".
1/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00319444
1. Use Tooling (A) and a suitable lifting device to place torque converter housing (1) onto
suitable cribbing, as shown.
Illustration 2 g00319445
2. Remove transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
3. Remove bolt (3) and washer (4) .
Illustration 3 g00319447
4. Remove torque converter speed sensor (5) .
2/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00319448
5. Remove bolts (6) that hold the torque converter to the torque converter housing.
Illustration 5 g00319449
6. Remove bolts (7) and pump drive flange (8) .
Illustration 6 g00319450
7. Remove bolt (9) that holds shaft (10) to the torque converter housing.
3/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00319451
8. Install Tooling (B) in pump drive gear (11) .
9. Lift pump drive gear (11) and drive gear shaft (10) . Lift drive gear shaft (10) out of the
torque converter housing bore.
10. Place the assembly to one side of the torque converter housing bore. Make sure that drive
gear shaft (10) is not in the torque converter housing bore.
Illustration 8 g00319453
11. Remove Tooling (B) from pump drive gear (11) .
12. Remove drive gear shaft (10) from pump drive gear (11) .
13. Remove bearing (12) from pump drive gear (11) .
4/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g03652939
14. Use Tooling (A) and a suitable lifting device to remove torque converter housing (1) . The
weight of torque converter housing (1) is approximately 113 kg (250 lb).
Illustration 10 g03652860
15. Turn torque converter housing (1) over to remove pump drive gear (11) .
Illustration 11 g00319455
5/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 16. Remove drive gear (13) .
Illustration 12 g00319456
17. Remove retaining ring (14) that holds output shaft (15) .
18. Use a soft faced hammer in order to free the bearing from the carrier assembly. Remove
output shaft (15) from the carrier assembly.
Illustration 13 g00319500
19. Remove seal ring (16) from output shaft (15) .
20. Use a suitable press to remove roller bearing (17) .
6/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00319458
21. Remove bolts (18) . Remove torque converter impeller (19) from the impeller housing.
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 22
through 28.
Illustration 15 g00877132
22. Turn impeller (20) to the opposite side.
23. Remove retaining ring (21) and spacer (22) from carrier shaft (23) .
24. Remove stator (24) .
7/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00877125
25. Remove retaining ring (25) and washer (26) from stator (24) . Repeat the procedure for the
opposite side of stator (24) .
Illustration 17 g00877126
Note: If necessary, Raise the temperature of the stator to a maximum temperature of 135 °C
(275 °F) for approximately 15 minutes.
26. Remove bearing race (27) , freewheel rollers (28) , freewheel springs (29) , and freewheel
cam (30) from stator (24) .
8/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00877129
27. Remove spacer (31) from impeller (20) .
Illustration 19 g00877133
28. Use a press to remove carrier shaft (23) from impeller (20) .
Illustration 20 g00877250
29. Remove bolts (32) and drive gear (33) from the torque converter impeller.
9/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00877257
30. Remove roller bearing (34) from torque converter impeller (19) .
Illustration 22 g00877258
31. Remove seal ring (36) from carrier assembly (35) .
32. If necessary, remove locating dowel (37) .
10/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHI...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01146281
33. Remove ring (39A) . Remove retaining ring (38) and impeller cover (39) from impeller
housing (40) .
Illustration 24 g00877261
34. Use Tooling (C) in order to remove retaining ring (41) .
Illustration 25 g00877262
35. Remove bearing spacer (42) .
36. Remove O-ring seal (43) .
11/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHI...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00877263
37. Turn the impeller housing onto the opposite side. Remove turbine assembly (44) .
Illustration 27 g00877264
38. Remove bolts (45) . Separate turbine (46) from turbine hub assembly (47) .
39. If necessary, remove locating dowel (48) .
Illustration 28 g00877265
12/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHI...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 40. Remove roller bearing (49) from the impeller housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Mar 26 09:34:41 UTC+0800 2020
13/13
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHI...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 5RS
Configuration: 962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHINE) POWERED BY 3126 ENGINE
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754104
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Pliers 1
D - Loctite 536 -
Illustration 1 g00877265
1/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: The notch on roller bearing (49) must be aligned with locating dowel (48) .
1. Install roller bearing (49) .
Illustration 2 g00877264
2. Install locating dowel (48) in turbine hub assembly (38) .
3. Install turbine hub assembly (47) to turbine (46) . Install bolts (45) . The torque for bolts
(45) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00877263
4. Install the impeller housing over turbine assembly (44) , as shown.
2/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g00877262
5. Install O-ring seal (43) .
6. Install bearing spacer (42) .
Illustration 5 g00877261
7. Use Tooling (C) in order to install retaining ring (41) .
Illustration 6 g01146281
3/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install impeller cover (39) and retaining ring (38) in impeller housing (40) . Install ring
(39A) .
Illustration 7 g00877258
9. Install locating dowel (37) .
10. Install seal ring (36) on carrier assembly (35) .
Illustration 8 g00877257
Note: The notch in roller bearing (34) must be facing upward.
11. Install roller bearing (34) in torque converter impeller (19) .
4/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00877250
12. Install drive gear (33) and bolts (32) on the torque converter impeller. The torque for bolts
(32) is 105 ± 15 N·m (75 ± 11 lb ft).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 13
through 18.
Illustration 10 g00877133
13. Use a suitable press to install carrier shaft (23) in impeller (20) .
5/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 11 g00877129
14. Install spacer (31) on impeller (20) .
Illustration 12 g00877126
Note: If necessary, Raise the temperature of stator (24) to a maximum temperature of 135 °
C (275 °F). Install the cam with the IMPELLER SIDE facing downward. Continue with the
installation until freewheel cam (30) contacts the retaining ring (not shown).
15. Install freewheel cam (30) , freewheel springs (29) , freewheel rollers (28) , and bearing race
(27) in stator (24) .
Note: Install freewheel springs (29) with the maximum number of loops toward the outside
diameter of freewheel cam (30) .
Illustration 13 g00877125
16. Install washer (26) and snap ring (25) on stator (24) . Repeat the procedure for the opposite
side of stator (24) .
6/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 14 g00877132
17. Install stator (24) on impeller (20) .
18. Install spacer (22) and snap ring (21) on carrier shaft (23) .
Illustration 15 g00319458
19. Install torque converter impeller (19) on the impeller housing.
20. Install bolts (18) . The torque for bolts (18) is 60 ± 7 N·m (44 ± 5 lb ft).
7/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 16 g00319500
21. Install roller bearing (17) on output shaft (15) .
22. Install seal ring (16) .
Illustration 17 g00319456
23. Install output shaft (15) in the carrier assembly.
24. Install retaining ring (14) that secures output shaft (15) .
Illustration 18 g00319455
25. Install drive gear (13) .
8/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 19 g03652860
26. Install pump drive gear (11) to the underside of torque converter housing (1) .
Illustration 20 g03652939
27. Install Tooling (A) and a suitable lifting device to install torque converter housing (1) onto
the torque converter assembly. The weight of torque converter housing (1) is approximately
113 kg (250 lb).
Illustration 21 g00319448
9/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHIN...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 28. Install bolts (6) that hold the torque converter to the torque converter housing. The torque
for bolts (6) are 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 22 g00319453
29. Install bearing (12) and drive gear shaft (10) in pump drive gear (11) .
30. Install Tooling (B) on pump drive gear (11) .
Illustration 23 g00319451
31. Place the assembly in the original position. Make sure that drive gear shaft (10) is in the
torque converter housing bore.
32. Remove Tooling (B) from pump drive gear (11) .
10/12
962G WHEEL LOADER /(COMMAND CONTROL STE/ 5RS00227-UP (MACHI...
2020/3/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...