1) The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2) It describes removing over 40 individual components in 38 steps, and installing them in reverse order over 29 steps.
3) Key components that must be removed include the transmission oil pump, torque converter speed sensor, various bolts and gears, and the turbine assembly. Proper alignment of locating dowels and notches in bearings is important when reassembling.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for each fastener. Tools required include link brackets, eyebolts and retaining ring pliers.
This document provides assembly instructions for a torque converter in a 962G wheel loader. It outlines 40 steps to disassemble the torque converter into its individual components and 29 steps to reassemble it. Key components that are removed and installed include the torque converter housing, various gears, bearings, seals, and fasteners. Special tools are required for tasks like removing retaining rings.
This document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps for disassembly, removing components like the transmission oil pump, speed sensor, bolts, gears, shafts, bearings, seals, and housing. It then describes 18 steps for reassembly, showing how to install these same components in reverse order, like installing bearings, seals, gears, shafts, housing, and bolts, while applying loctite and torquing bolts to specifications. Tools required are also listed.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for the fasteners. Tools required include link brackets, eyebolts and retaining ring pliers.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...jfjkskefmsmem
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document provides very detailed technical instructions for taking apart and rebuilding the wheel loader's torque converter.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...ufjjjsekkemmd
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document is a service repair manual for maintenance technicians to service the machine's powertrain.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fujsejfjksekkkm
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fjjskekdmnsme
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for each fastener. Tools required include link brackets, eyebolts and retaining ring pliers.
This document provides assembly instructions for a torque converter in a 962G wheel loader. It outlines 40 steps to disassemble the torque converter into its individual components and 29 steps to reassemble it. Key components that are removed and installed include the torque converter housing, various gears, bearings, seals, and fasteners. Special tools are required for tasks like removing retaining rings.
This document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps for disassembly, removing components like the transmission oil pump, speed sensor, bolts, gears, shafts, bearings, seals, and housing. It then describes 18 steps for reassembly, showing how to install these same components in reverse order, like installing bearings, seals, gears, shafts, housing, and bolts, while applying loctite and torquing bolts to specifications. Tools required are also listed.
This document provides instructions for disassembling and assembling the torque converter of a 962G wheel loader. It describes 40 steps to disassemble the various components of the torque converter including the housing, pump, gears, shafts, bearings and seals. It then describes 28 steps for reassembling the components in reverse order, noting the proper alignment and torque specifications for the fasteners. Tools required include link brackets, eyebolts and retaining ring pliers.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...jfjkskefmsmem
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document provides very detailed technical instructions for taking apart and rebuilding the wheel loader's torque converter.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...ufjjjsekkemmd
This document provides instructions for disassembling and assembling the torque converter of a Caterpillar 962G wheel loader. It describes 40 steps to disassemble the torque converter by removing components like the transmission oil pump, speed sensor, bolts, gears, bearings, seals, and shafts. It then describes 28 steps for reassembling the torque converter by reversing the disassembly process and noting proper alignment of parts, use of threadlocker, and torque specifications for fasteners. The overall document is a service repair manual for maintenance technicians to service the machine's powertrain.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fujsejfjksekkkm
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
Caterpillar cat 962 g wheel loader (prefix 6ew) service repair manual (6ew000...fjjskekdmnsme
1. The document provides step-by-step instructions for disassembling and assembling the torque converter of a 962G wheel loader.
2. It lists 39 steps for disassembly and 40 steps for assembly, showing illustrations and required tools for each step.
3. The steps include removing components like the transmission oil pump, torque converter speed sensor, bolts, gears, bearings, seals, and installing them in reverse order.
JCB JS160JS180 Tracked Excavator Service Repair Manual SN 01776500 to 0177749...jfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB JS200JS210JS220 Tracked Excavator Service Repair Manual SN 01782453 to 01...jfkekd9d8di
This document provides information about identifying JCB excavator machines and components. It discusses machine identification plates, engine identification numbers, FOPS and ROPS data plates. It also provides tables of torque settings for zinc plated, Dacromet and metric grade fasteners used on JCB excavators. The summary highlights key identification details and specifies the purpose of providing torque settings for correct maintenance and repair.
JCB JS145 Tracked Excavator Service Repair Manual SN 01786864 to 01788884.pdfjfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB JS115 Tracked Excavator Service Repair Manual SN01786452 to 01786462.pdfjfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB JS130 Tracked Excavator Service Repair Manual SN 01786463 to 01786863.pdfjfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB 535-67 Telescopic Handler Service Repair Manual SN 572775.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-120 Telescopic Handler Service Repair Manual SN 562601.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-110 Telescopic Handler Service Repair Manual SN 563359.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-95 Telescopic Handler Service Repair Manual SN564980.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 1CX (series 1) Backhoe Loader Service Repair Manual SN751600 and up.pdfjfkekd9d8di
This document provides information about identifying JCB machines and their components. It discusses machine identification plates that contain serial numbers for the machine and major units. It also describes typical engine identification numbers. The document outlines torque settings for different types of fasteners used on JCB machines, such as zinc plated and Dacromet fasteners. Tables are included that specify torque values based on fastener size, grade, and lubrication conditions.
JCB 4DX Backhoe Loader Service Repair Manual.pdfjfkekd9d8di
This service manual provides information on routine maintenance procedures for a JCB 4DX backhoe loader, including:
1. Greasing procedures for the loader arms, backhoe, front and rear axles, propshafts, clam shovel, and other components at regular intervals.
2. Procedures for cleaning the pre-cleaner and replacing the engine air filter elements.
3. Checking engine oil levels and changing the engine oil and filter.
4. Inspecting and adjusting tension on the fan belt as needed.
5. Additional sections cover coolant types, engine preservation when idle, oiling control levers, and other maintenance tasks.
This document provides instructions for disassembling and assembling the front axle of a M314F wheeled excavator. The disassembly procedure involves removing 22 components of the front axle including bearings, seals, gears and housings. The assembly procedure consists of 31 steps to reinstall these components in reverse order, noting specific tools and processes required like adjusting bearing depths and torque specifications. Precise assembly is important to achieve the correct rolling torque between the pinion and axle housing.
Clark GPX 40 Forklift Service Repair Manual.pdfjfkekd9d8di
The service manual includes new information for overhauling the GM Vortec V-6 engine and new truck specifications. It also contains applicable sections carried over from the previous manual, SM593, with footers on those pages remaining unchanged. The manual provides maintenance and repair instructions for Clark lift trucks models GPX 35/40/50E.
Clark GPX 50E Forklift Service Repair Manual.pdfjfkekd9d8di
The service manual includes new information for overhauling the GM Vortec V-6 engine and new truck specifications. It also contains applicable sections carried over from the previous manual, SM593, with footers on those pages remaining unchanged. The manual provides maintenance and repair instructions for Clark lift trucks models GPX 35/40/50E.
Clark GPX 35 Forklift Service Repair Manual.pdfjfkekd9d8di
The service manual includes new information for overhauling the GM Vortec V-6 engine and new truck specifications. It also contains applicable sections carried over from the previous manual, SM593, with footers on those pages remaining unchanged. The manual provides maintenance and repair instructions for Clark lift trucks models GPX 35/40/50E.
This document provides instructions for removing and installing the final drive planetary carrier on a D11R track-type tractor. It describes using various tools to lift and support components as they are removed and installed. The procedure involves removing bolts and pins, then using lifting brackets and cylinders to maneuver the heavy carrier and associated gear and hub components. Precautions are given for containing fluids and properly disposing of them.
The document provides instructions for removing and installing various components of the rear power take-off (RPTO) on a Caterpillar D11R track-type tractor, including the adapter, bearing cups and cones, hydraulic pump drive gear, and nuts and bolts. Specific tools are listed and illustrations show each step of disassembly and reassembly. Separate sections provide procedures for removing and installing the vibration damper and pulley.
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components such as the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, including attaching various tools and ensuring proper torque for fasteners.
The document provides instructions for disassembling and assembling the cylinder head of a Caterpillar 3508 engine. Key steps include:
1. Draining the coolant and removing bolts and tubes to access the cylinder head.
2. Using lifting devices and tools to remove the cylinder head, which weighs approximately 47 kg.
3. Disassembling the cylinder head by removing valves, springs, guides and other components.
4. Cleaning and inspecting parts before assembly, which involves installing new components like guides, inserts and seals in reverse order of disassembly.
The document provides instructions for removing and installing the front housing on a Caterpillar C18 engine. It describes:
1) Removing components like the camshaft position sensor, crankshaft position sensor, engine support, camshaft gear and crankshaft front seal before removing the front housing.
2) Removing bolts to separate the front housing from the cylinder block, and removing seals from the housing.
3) Cleaning surfaces and installing new seals before reversing the removal process and torquing bolts to specifications.
JCB JS160JS180 Tracked Excavator Service Repair Manual SN 01776500 to 0177749...jfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB JS200JS210JS220 Tracked Excavator Service Repair Manual SN 01782453 to 01...jfkekd9d8di
This document provides information about identifying JCB excavator machines and components. It discusses machine identification plates, engine identification numbers, FOPS and ROPS data plates. It also provides tables of torque settings for zinc plated, Dacromet and metric grade fasteners used on JCB excavators. The summary highlights key identification details and specifies the purpose of providing torque settings for correct maintenance and repair.
JCB JS145 Tracked Excavator Service Repair Manual SN 01786864 to 01788884.pdfjfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB JS115 Tracked Excavator Service Repair Manual SN01786452 to 01786462.pdfjfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB JS130 Tracked Excavator Service Repair Manual SN 01786463 to 01786863.pdfjfkekd9d8di
This document provides information about identifying JCB excavator models and their components. It discusses machine identification plates that contain the serial number and product identification number. It also describes typical identification numbers found on engine plates and other components. The document outlines torque settings for different types of fasteners used on JCB machines, distinguishing between zinc plated and Dacromet fasteners. Tables of torque settings are provided for UNF and metric grade bolts under lubricated and unlubricated conditions.
JCB 535-67 Telescopic Handler Service Repair Manual SN 572775.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-120 Telescopic Handler Service Repair Manual SN 562601.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-110 Telescopic Handler Service Repair Manual SN 563359.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-95 Telescopic Handler Service Repair Manual SN564980.pdfjfkekd9d8di
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 1CX (series 1) Backhoe Loader Service Repair Manual SN751600 and up.pdfjfkekd9d8di
This document provides information about identifying JCB machines and their components. It discusses machine identification plates that contain serial numbers for the machine and major units. It also describes typical engine identification numbers. The document outlines torque settings for different types of fasteners used on JCB machines, such as zinc plated and Dacromet fasteners. Tables are included that specify torque values based on fastener size, grade, and lubrication conditions.
JCB 4DX Backhoe Loader Service Repair Manual.pdfjfkekd9d8di
This service manual provides information on routine maintenance procedures for a JCB 4DX backhoe loader, including:
1. Greasing procedures for the loader arms, backhoe, front and rear axles, propshafts, clam shovel, and other components at regular intervals.
2. Procedures for cleaning the pre-cleaner and replacing the engine air filter elements.
3. Checking engine oil levels and changing the engine oil and filter.
4. Inspecting and adjusting tension on the fan belt as needed.
5. Additional sections cover coolant types, engine preservation when idle, oiling control levers, and other maintenance tasks.
This document provides instructions for disassembling and assembling the front axle of a M314F wheeled excavator. The disassembly procedure involves removing 22 components of the front axle including bearings, seals, gears and housings. The assembly procedure consists of 31 steps to reinstall these components in reverse order, noting specific tools and processes required like adjusting bearing depths and torque specifications. Precise assembly is important to achieve the correct rolling torque between the pinion and axle housing.
Clark GPX 40 Forklift Service Repair Manual.pdfjfkekd9d8di
The service manual includes new information for overhauling the GM Vortec V-6 engine and new truck specifications. It also contains applicable sections carried over from the previous manual, SM593, with footers on those pages remaining unchanged. The manual provides maintenance and repair instructions for Clark lift trucks models GPX 35/40/50E.
Clark GPX 50E Forklift Service Repair Manual.pdfjfkekd9d8di
The service manual includes new information for overhauling the GM Vortec V-6 engine and new truck specifications. It also contains applicable sections carried over from the previous manual, SM593, with footers on those pages remaining unchanged. The manual provides maintenance and repair instructions for Clark lift trucks models GPX 35/40/50E.
Clark GPX 35 Forklift Service Repair Manual.pdfjfkekd9d8di
The service manual includes new information for overhauling the GM Vortec V-6 engine and new truck specifications. It also contains applicable sections carried over from the previous manual, SM593, with footers on those pages remaining unchanged. The manual provides maintenance and repair instructions for Clark lift trucks models GPX 35/40/50E.
This document provides instructions for removing and installing the final drive planetary carrier on a D11R track-type tractor. It describes using various tools to lift and support components as they are removed and installed. The procedure involves removing bolts and pins, then using lifting brackets and cylinders to maneuver the heavy carrier and associated gear and hub components. Precautions are given for containing fluids and properly disposing of them.
The document provides instructions for removing and installing various components of the rear power take-off (RPTO) on a Caterpillar D11R track-type tractor, including the adapter, bearing cups and cones, hydraulic pump drive gear, and nuts and bolts. Specific tools are listed and illustrations show each step of disassembly and reassembly. Separate sections provide procedures for removing and installing the vibration damper and pulley.
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components such as the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, including attaching various tools and ensuring proper torque for fasteners.
The document provides instructions for disassembling and assembling the cylinder head of a Caterpillar 3508 engine. Key steps include:
1. Draining the coolant and removing bolts and tubes to access the cylinder head.
2. Using lifting devices and tools to remove the cylinder head, which weighs approximately 47 kg.
3. Disassembling the cylinder head by removing valves, springs, guides and other components.
4. Cleaning and inspecting parts before assembly, which involves installing new components like guides, inserts and seals in reverse order of disassembly.
The document provides instructions for removing and installing the front housing on a Caterpillar C18 engine. It describes:
1) Removing components like the camshaft position sensor, crankshaft position sensor, engine support, camshaft gear and crankshaft front seal before removing the front housing.
2) Removing bolts to separate the front housing from the cylinder block, and removing seals from the housing.
3) Cleaning surfaces and installing new seals before reversing the removal process and torquing bolts to specifications.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 6EW
Configuration: 962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754103
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Retaining Ring Pliers 1
Start By:
A. Separate the torque converter from the transmission and from the output gears. Refer to
Disassembly and Assembly, "Torque Converter from Transmission, Output Gears -
Separate".
1/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00319444
1. Use Tooling (A) and a suitable lifting device to place torque converter housing (1) onto
suitable cribbing, as shown.
Illustration 2 g00319445
2. Remove transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Remove".
3. Remove bolt (3) and washer (4) .
Illustration 3 g00319447
4. Remove torque converter speed sensor (5) .
2/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00319448
5. Remove bolts (6) that hold the torque converter to the torque converter housing.
Illustration 5 g00319449
6. Remove bolts (7) and pump drive flange (8) .
Illustration 6 g00319450
7. Remove bolt (9) that holds shaft (10) to the torque converter housing.
3/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00319451
8. Install Tooling (B) in pump drive gear (11) .
9. Lift pump drive gear (11) and drive gear shaft (10) . Lift drive gear shaft (10) out of the
torque converter housing bore.
10. Place the assembly to one side of the torque converter housing bore. Make sure that drive
gear shaft (10) is not in the torque converter housing bore.
Illustration 8 g00319453
11. Remove Tooling (B) from pump drive gear (11) .
12. Remove drive gear shaft (10) from pump drive gear (11) .
13. Remove bearing (12) from pump drive gear (11) .
4/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g03652939
14. Use Tooling (A) and a suitable lifting device to remove torque converter housing (1) . The
weight of torque converter housing (1) is approximately 113 kg (250 lb).
Illustration 10 g03652860
15. Turn torque converter housing (1) over to remove pump drive gear (11) .
Illustration 11 g00319455
5/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 16. Remove drive gear (13) .
Illustration 12 g00319456
17. Remove retaining ring (14) that holds output shaft (15) .
18. Use a soft faced hammer in order to free the bearing from the carrier assembly. Remove
output shaft (15) from the carrier assembly.
Illustration 13 g00319500
19. Remove seal ring (16) from output shaft (15) .
20. Use a suitable press to remove roller bearing (17) .
6/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00319458
21. Remove bolts (18) . Remove torque converter impeller (19) from the impeller housing.
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 22
through 28.
Illustration 15 g00877132
22. Turn impeller (20) to the opposite side.
23. Remove retaining ring (21) and spacer (22) from carrier shaft (23) .
24. Remove stator (24) .
7/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g00877125
25. Remove retaining ring (25) and washer (26) from stator (24) . Repeat the procedure for the
opposite side of stator (24) .
Illustration 17 g00877126
Note: If necessary, Raise the temperature of the stator to a maximum temperature of 135 °C
(275 °F) for approximately 15 minutes.
26. Remove bearing race (27) , freewheel rollers (28) , freewheel springs (29) , and freewheel
cam (30) from stator (24) .
8/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g00877129
27. Remove spacer (31) from impeller (20) .
Illustration 19 g00877133
28. Use a press to remove carrier shaft (23) from impeller (20) .
Illustration 20 g00877250
29. Remove bolts (32) and drive gear (33) from the torque converter impeller.
9/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00877257
30. Remove roller bearing (34) from torque converter impeller (19) .
Illustration 22 g00877258
31. Remove seal ring (36) from carrier assembly (35) .
32. If necessary, remove locating dowel (37) .
10/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01146281
33. Remove ring (39A) . Remove retaining ring (38) and impeller cover (39) from impeller
housing (40) .
Illustration 24 g00877261
34. Use Tooling (C) in order to remove retaining ring (41) .
Illustration 25 g00877262
35. Remove bearing spacer (42) .
36. Remove O-ring seal (43) .
11/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00877263
37. Turn the impeller housing onto the opposite side. Remove turbine assembly (44) .
Illustration 27 g00877264
38. Remove bolts (45) . Separate turbine (46) from turbine hub assembly (47) .
39. If necessary, remove locating dowel (48) .
Illustration 28 g00877265
12/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 40. Remove roller bearing (49) from the impeller housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 23 10:36:14 UTC+0800 2020
13/13
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 962G WHEEL LOADER 6EW
Configuration: 962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train
Media Number -SENR1381-10 Publication Date -01/10/2007 Date Updated -25/10/2007
i05754104
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 3
B 1P-7405 Eyebolt 2
C 2P-8312 Pliers 1
D - Loctite 536 -
Illustration 1 g00877265
1/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: The notch on roller bearing (49) must be aligned with locating dowel (48) .
1. Install roller bearing (49) .
Illustration 2 g00877264
2. Install locating dowel (48) in turbine hub assembly (38) .
3. Install turbine hub assembly (47) to turbine (46) . Install bolts (45) . The torque for bolts
(45) is 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 3 g00877263
4. Install the impeller housing over turbine assembly (44) , as shown.
2/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 4 g00877262
5. Install O-ring seal (43) .
6. Install bearing spacer (42) .
Illustration 5 g00877261
7. Use Tooling (C) in order to install retaining ring (41) .
Illustration 6 g01146281
3/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 8. Install impeller cover (39) and retaining ring (38) in impeller housing (40) . Install ring
(39A) .
Illustration 7 g00877258
9. Install locating dowel (37) .
10. Install seal ring (36) on carrier assembly (35) .
Illustration 8 g00877257
Note: The notch in roller bearing (34) must be facing upward.
11. Install roller bearing (34) in torque converter impeller (19) .
4/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00877250
12. Install drive gear (33) and bolts (32) on the torque converter impeller. The torque for bolts
(32) is 105 ± 15 N·m (75 ± 11 lb ft).
Note: If the torque converter is equipped with a freewheel stator, continue with Steps 13
through 18.
Illustration 10 g00877133
13. Use a suitable press to install carrier shaft (23) in impeller (20) .
5/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 11 g00877129
14. Install spacer (31) on impeller (20) .
Illustration 12 g00877126
Note: If necessary, Raise the temperature of stator (24) to a maximum temperature of 135 °
C (275 °F). Install the cam with the IMPELLER SIDE facing downward. Continue with the
installation until freewheel cam (30) contacts the retaining ring (not shown).
15. Install freewheel cam (30) , freewheel springs (29) , freewheel rollers (28) , and bearing race
(27) in stator (24) .
Note: Install freewheel springs (29) with the maximum number of loops toward the outside
diameter of freewheel cam (30) .
Illustration 13 g00877125
16. Install washer (26) and snap ring (25) on stator (24) . Repeat the procedure for the opposite
side of stator (24) .
6/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 14 g00877132
17. Install stator (24) on impeller (20) .
18. Install spacer (22) and snap ring (21) on carrier shaft (23) .
Illustration 15 g00319458
19. Install torque converter impeller (19) on the impeller housing.
20. Install bolts (18) . The torque for bolts (18) is 60 ± 7 N·m (44 ± 5 lb ft).
7/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 16 g00319500
21. Install roller bearing (17) on output shaft (15) .
22. Install seal ring (16) .
Illustration 17 g00319456
23. Install output shaft (15) in the carrier assembly.
24. Install retaining ring (14) that secures output shaft (15) .
Illustration 18 g00319455
25. Install drive gear (13) .
8/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 19 g03652860
26. Install pump drive gear (11) to the underside of torque converter housing (1) .
Illustration 20 g03652939
27. Install Tooling (A) and a suitable lifting device to install torque converter housing (1) onto
the torque converter assembly. The weight of torque converter housing (1) is approximately
113 kg (250 lb).
Illustration 21 g00319448
9/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 28. Install bolts (6) that hold the torque converter to the torque converter housing. The torque
for bolts (6) are 60 ± 7 N·m (44 ± 5 lb ft).
Illustration 22 g00319453
29. Install bearing (12) and drive gear shaft (10) in pump drive gear (11) .
30. Install Tooling (B) on pump drive gear (11) .
Illustration 23 g00319451
31. Place the assembly in the original position. Make sure that drive gear shaft (10) is in the
torque converter housing bore.
32. Remove Tooling (B) from pump drive gear (11) .
10/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 24 g00319450
33. Install bolt (9) that holds shaft (10) to torque converter housing (1) . The torque for bolt (9)
is 105 ± 20 N·m (75 ± 15 lb ft).
Illustration 25 g00319449
34. Install pump drive flange (8) and bolts (7) . The torque for bolts (7) is 60 ± 7 N·m (44 ± 5 lb
ft).
Illustration 26 g00319447
11/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 35. Apply Tooling (D) to torque converter speed sensor (5) . Install torque converter speed
sensor (5) . Adjust the torque converter speed sensor in order to maintain an air gap of 0.71
± 0.18 mm (0.028 ± 0.007 inch). The torque for torque converter speed sensor (5) is 25 ± 5
N·m (18 ± 4 lb ft).
Illustration 27 g00319445
36. Install washer (4) and bolt (3) . The torque for bolt (3) is 105 ± 20 N·m (75 ± 15 lb ft).
37. Install transmission oil pump (2) . Refer to Disassembly and Assembly, "Transmission Oil
Pump - Install".
Illustration 28 g00319444
38. Install Tooling (A) and a suitable lifting device to torque converter housing (1) , as shown.
End By: Connect the torque converter to the transmission and to the output gears. Refer to
Disassembly and Assembly, "Torque Converter to Transmission, Output Gears - Connect".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Mar 23 10:37:13 UTC+0800 2020
12/12
962G Wheel Loader 6EW00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/3/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...