This document provides disassembly and assembly instructions for the piston pump (steering) on 930K Wheel Loader models. The procedures include removing and installing various components of the piston pump like the head, pistons, housing, bearings, seals and more. Detailed illustrations are provided to identify the specific components and tools required are listed to correctly disassemble and reassemble the piston pump. Safety precautions are noted throughout to warn of potential injury from parts under spring pressure.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...ufjjjskkemmd
This service repair manual provides instructions for disassembling and assembling the steering piston pump on 930K Wheel Loader models. The disassembly procedure involves removing 21 components from the pump housing, head, and rotating group. The assembly procedure involves installing the components in reverse order and adjusting shims to set proper bearing preload. Tools and safety precautions are also listed.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...ufjjsjefkskekmme
This service repair manual provides instructions for disassembling and assembling the steering piston pump on 930K Wheel Loader models. The disassembly procedure involves removing 21 components from the pump housing, head, and rotating group. The assembly procedure involves installing these components in reverse order and adjusting shims to set proper bearing preload. Tools and safety precautions are also listed.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...fjjskekksmem
This service repair manual provides instructions for disassembly and assembly of the steering piston pump on 930K Wheel Loader models. The document outlines 29 steps for disassembly, which include removing bolts, seals, springs, valves, and other components. It then lists 31 steps for assembly, noting that parts should be cleaned and lubricated before reinstallation and cautioning that spring loaded parts require careful handling to avoid injury. Tools required for disassembly and assembly are also listed.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...fjjsekkmdmes
This service repair manual provides instructions for disassembly and assembly of the steering piston pump on 930K Wheel Loader models. The document outlines 29 steps for disassembly, which include removing bolts, seals, springs, valves, and other components. It also outlines 36 steps for assembly, noting that parts should be cleaned and lubricated before reinstallation and cautioning that spring loaded parts require careful handling to avoid injury. Tools including pullers, drivers, feeler gauges and dial indicators are listed for the repair work.
This document provides disassembly and assembly instructions for the piston pump used in steering systems on 930K wheel loaders. It details removing and installing over 30 individual components of the pump in multiple steps. Proper tools are listed and safety precautions noted, such as releasing spring pressure carefully. The document is intended to guide maintenance technicians in repairing the steering piston pump.
This document provides disassembly and assembly instructions for the piston pump (steering) on 930K Wheel Loader models. It outlines 29 steps to disassemble the pump, including removing hoses, bolts, valves, springs, seals, bearings and other components. It then lists 31 steps for reassembling the pump components in reverse order, noting any specific installation procedures or torque specifications. Safety cautions are provided throughout for components under spring pressure.
This document provides disassembly and assembly instructions for the piston pump (steering) used in 930K Wheel Loaders. The summary is:
1. The document outlines the step-by-step process for disassembling the piston pump, which includes removing components like the head, port plate, pistons, springs, and seals.
2. The assembly procedure describes installing these components in reverse order and includes checks to ensure proper bearing preload and zero end play on the shaft assembly.
3. Special tools and safety precautions are listed, and notes emphasize inspecting parts for wear and applying a light film of oil before assembly.
Caterpillar cat 930 k wheel loader (prefix frk) service repair manual (frk000...ufjjsjefkskekmme
This document provides disassembly and assembly instructions for the piston pump (steering) used in 930K Wheel Loaders. The summary is:
1) The piston pump is removed by disconnecting hose assemblies, attaching a lifting device, and removing bolts.
2) Disassembly of the piston pump involves removing components like the compensator valve, head, port plate, pistons, springs, and bearings.
3) Assembly is the reverse of disassembly, ensuring proper placement and torque of components, and using tools to set bearing preloads and check for end play.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...ufjjjskkemmd
This service repair manual provides instructions for disassembling and assembling the steering piston pump on 930K Wheel Loader models. The disassembly procedure involves removing 21 components from the pump housing, head, and rotating group. The assembly procedure involves installing the components in reverse order and adjusting shims to set proper bearing preload. Tools and safety precautions are also listed.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...ufjjsjefkskekmme
This service repair manual provides instructions for disassembling and assembling the steering piston pump on 930K Wheel Loader models. The disassembly procedure involves removing 21 components from the pump housing, head, and rotating group. The assembly procedure involves installing these components in reverse order and adjusting shims to set proper bearing preload. Tools and safety precautions are also listed.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...fjjskekksmem
This service repair manual provides instructions for disassembly and assembly of the steering piston pump on 930K Wheel Loader models. The document outlines 29 steps for disassembly, which include removing bolts, seals, springs, valves, and other components. It then lists 31 steps for assembly, noting that parts should be cleaned and lubricated before reinstallation and cautioning that spring loaded parts require careful handling to avoid injury. Tools required for disassembly and assembly are also listed.
Caterpillar cat 930 k wheel loader (prefix eye) service repair manual (eye000...fjjsekkmdmes
This service repair manual provides instructions for disassembly and assembly of the steering piston pump on 930K Wheel Loader models. The document outlines 29 steps for disassembly, which include removing bolts, seals, springs, valves, and other components. It also outlines 36 steps for assembly, noting that parts should be cleaned and lubricated before reinstallation and cautioning that spring loaded parts require careful handling to avoid injury. Tools including pullers, drivers, feeler gauges and dial indicators are listed for the repair work.
This document provides disassembly and assembly instructions for the piston pump used in steering systems on 930K wheel loaders. It details removing and installing over 30 individual components of the pump in multiple steps. Proper tools are listed and safety precautions noted, such as releasing spring pressure carefully. The document is intended to guide maintenance technicians in repairing the steering piston pump.
This document provides disassembly and assembly instructions for the piston pump (steering) on 930K Wheel Loader models. It outlines 29 steps to disassemble the pump, including removing hoses, bolts, valves, springs, seals, bearings and other components. It then lists 31 steps for reassembling the pump components in reverse order, noting any specific installation procedures or torque specifications. Safety cautions are provided throughout for components under spring pressure.
This document provides disassembly and assembly instructions for the piston pump (steering) used in 930K Wheel Loaders. The summary is:
1. The document outlines the step-by-step process for disassembling the piston pump, which includes removing components like the head, port plate, pistons, springs, and seals.
2. The assembly procedure describes installing these components in reverse order and includes checks to ensure proper bearing preload and zero end play on the shaft assembly.
3. Special tools and safety precautions are listed, and notes emphasize inspecting parts for wear and applying a light film of oil before assembly.
Caterpillar cat 930 k wheel loader (prefix frk) service repair manual (frk000...ufjjsjefkskekmme
This document provides disassembly and assembly instructions for the piston pump (steering) used in 930K Wheel Loaders. The summary is:
1) The piston pump is removed by disconnecting hose assemblies, attaching a lifting device, and removing bolts.
2) Disassembly of the piston pump involves removing components like the compensator valve, head, port plate, pistons, springs, and bearings.
3) Assembly is the reverse of disassembly, ensuring proper placement and torque of components, and using tools to set bearing preloads and check for end play.
JCB 530-110 Telescopic Handler Service Repair Manual SN 563359.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 535-67 Telescopic Handler Service Repair Manual SN 572775.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-120 Telescopic Handler Service Repair Manual SN 562601.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-95 Telescopic Handler Service Repair Manual SN564980.pdffujsekmd9dik
This document provides lubrication specifications and fluid capacities for various JCB machine models, including 525, 527, 530, 535 and 537 models. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases and other lubricants. It also provides coolant mixture recommendations and notes that new engines do not require a break-in period and should be used immediately in normal work cycles.
JCB 4DX Backhoe Loader Service Repair Manual.pdffujsekmd9dik
This service manual provides information on maintenance and repair of the 4DX Backhoe Loader. It includes sections on general information, routine maintenance, attachments, body and framework, electrics, controls, hydraulics, transmission, brakes, steering and engine. The manual provides information on identification plates, torque settings, greasing points, cleaning air filters, and replacing engine coolant. It also includes details on preservation for storing the machine when not in use for long periods.
JCB 1CX (series 1) Backhoe Loader Service Repair Manual SN751600 and up.pdffujsekmd9dik
This document provides information about identifying JCB machines and their components. It discusses machine identification plates that contain serial numbers for the machine and major units. It also describes typical engine identification numbers. The document outlines torque settings for different types of fasteners used on JCB machines, such as zinc plated and Dacromet fasteners. Tables are included that specify torque values based on fastener size, grade, and lubrication conditions.
Clark GPX 40 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 50E Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 35 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
The document provides instructions for removing and installing the final drive planetary carrier on a D11R track-type tractor. It describes using various tools to lift and support the heavy components. The removal process involves removing bolts, installing lifting brackets, and using hydraulic tools to separate the carrier from the final drive. Precautions are listed for containing fluids during disassembly.
The document provides instructions for removing and installing the front axle of a M314F wheeled excavator. It details:
1) Removing the front axle assembly from the machine and disassembling it by removing components like the differential, bearings, and seals.
2) The assembly procedure which includes measuring clearances, installing bearings and seals, and adjusting the pinion depth using shims.
3) Tightening the pinion nut to the specified torque and reinstalling the front axle assembly onto the machine.
The document provides instructions for disassembling and assembling the cylinder head of a D11R track-type tractor. It describes removing components like the cylinder head, valves, valve guides, and valve lifters. It then describes the process for assembling these components in reverse order, noting that parts should be kept clean and lubricated with engine oil during assembly. Tools are listed for tasks like compressing valve springs and installing valve guides.
The document provides instructions for removing and installing various components of the rear power take-off (RPTO) system on a Caterpillar D11R track-type tractor, including the adapter, bearing cups and cones, hydraulic pump drive gear, and nuts and bolts. Specific tools are listed and illustrations show the components and steps to disassemble and reassemble the RPTO. Separate sections provide procedures for removing and installing the vibration damper and pulley.
The document provides instructions for removing and installing the front housing on a Caterpillar C18 engine. It describes:
1) Removing components like the camshaft position sensor, crankshaft position sensor, engine support, camshaft gear and crankshaft front seal before removing the front housing.
2) Removing bolts to separate the front housing from the cylinder block, and removing the front oil seal from the housing.
3) Cleaning surfaces and installing the front oil seal and housing back onto the cylinder block using thread lock compound on the bolts.
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components such as the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, including attaching various tools and ensuring proper torque for fasteners.
The document provides instructions for removing and installing final drives and the power train oil filter on a D6R track-type tractor. Key steps include using tools to remove the outer axle and final drive from the machine. The final drive planetary carriers can be removed in the chassis. Instructions are also given for disassembling and assembling the final drives and oil filter, which involves removing seals, gears, and other components and cleaning parts before reassembly.
This document provides instructions for disassembling and assembling components of the right planetary and brake, power train oil pump, and other parts of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, removing gears, discs, seals, and other parts. It then provides 22 steps to reassemble the components. A separate section provides 12 steps to remove and install the power train oil pump, disconnecting hoses and removing mounting bolts.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3516B engine used in a 994K wheel loader. The removal process involves draining coolant, removing connecting tubes and bolts, and lifting off the cylinder head. The installation is the reverse, and includes cleaning surfaces, installing new seals and gaskets, and torquing bolts in a specific sequence. Valves, guides, and other components are also removed and installed using various tools as outlined in the procedure.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3516E engine. It outlines the required tools and gives step-by-step procedures for disassembling and assembling the cylinder head components, including removing and installing the cylinder head, valves, valve guides, valve seat inserts, and valve lifters. Safety notices are provided throughout to warn technicians of potential hazards during disassembly and assembly.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 992K wheel loader with a C32 engine, including:
1) The crankshaft front seal using various tools to puncture, pry, and remove the seal and sleeve.
2) The front gear group using bolts, plates and shafts.
3) The front housing using bolts, seals and lifting equipment to remove the heavy component.
4) The valve mechanism cover using bolts and seals after loosening breathers and hoses.
JCB 530-110 Telescopic Handler Service Repair Manual SN 563359.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 535-67 Telescopic Handler Service Repair Manual SN 572775.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-120 Telescopic Handler Service Repair Manual SN 562601.pdffujsekmd9dik
This document provides specifications for fluids, lubricants, capacities and torque settings for various JCB machine models including the 525-58/67, 527-58/67, 530-95, 530-110, 530-120, 537-120, 537-130, 525-58 Farm Special Plus 530-67 and 535-67. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases, coolants and their specifications. It also provides fluid capacities for items like the fuel tank, engine, gearbox, axles, brake system and hydraulic tank.
JCB 530-95 Telescopic Handler Service Repair Manual SN564980.pdffujsekmd9dik
This document provides lubrication specifications and fluid capacities for various JCB machine models, including 525, 527, 530, 535 and 537 models. It lists recommended engine oils, transmission fluids, hydraulic fluids, greases and other lubricants. It also provides coolant mixture recommendations and notes that new engines do not require a break-in period and should be used immediately in normal work cycles.
JCB 4DX Backhoe Loader Service Repair Manual.pdffujsekmd9dik
This service manual provides information on maintenance and repair of the 4DX Backhoe Loader. It includes sections on general information, routine maintenance, attachments, body and framework, electrics, controls, hydraulics, transmission, brakes, steering and engine. The manual provides information on identification plates, torque settings, greasing points, cleaning air filters, and replacing engine coolant. It also includes details on preservation for storing the machine when not in use for long periods.
JCB 1CX (series 1) Backhoe Loader Service Repair Manual SN751600 and up.pdffujsekmd9dik
This document provides information about identifying JCB machines and their components. It discusses machine identification plates that contain serial numbers for the machine and major units. It also describes typical engine identification numbers. The document outlines torque settings for different types of fasteners used on JCB machines, such as zinc plated and Dacromet fasteners. Tables are included that specify torque values based on fastener size, grade, and lubrication conditions.
Clark GPX 40 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 50E Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
Clark GPX 35 Forklift Service Repair Manual.pdffujsekmd9dik
The document is a service manual for Clark GPX 35/40/50E trucks. It includes new overhaul information for GM Vortec V-6 engines and new truck specifications. The manual contains sections on engines, cooling systems, fuel systems, transmissions, electrical systems, drive axles, wheels and tires, braking systems, steering systems, hydraulic systems, uprights, and specifications.
The document provides instructions for removing and installing the final drive planetary carrier on a D11R track-type tractor. It describes using various tools to lift and support the heavy components. The removal process involves removing bolts, installing lifting brackets, and using hydraulic tools to separate the carrier from the final drive. Precautions are listed for containing fluids during disassembly.
The document provides instructions for removing and installing the front axle of a M314F wheeled excavator. It details:
1) Removing the front axle assembly from the machine and disassembling it by removing components like the differential, bearings, and seals.
2) The assembly procedure which includes measuring clearances, installing bearings and seals, and adjusting the pinion depth using shims.
3) Tightening the pinion nut to the specified torque and reinstalling the front axle assembly onto the machine.
The document provides instructions for disassembling and assembling the cylinder head of a D11R track-type tractor. It describes removing components like the cylinder head, valves, valve guides, and valve lifters. It then describes the process for assembling these components in reverse order, noting that parts should be kept clean and lubricated with engine oil during assembly. Tools are listed for tasks like compressing valve springs and installing valve guides.
The document provides instructions for removing and installing various components of the rear power take-off (RPTO) system on a Caterpillar D11R track-type tractor, including the adapter, bearing cups and cones, hydraulic pump drive gear, and nuts and bolts. Specific tools are listed and illustrations show the components and steps to disassemble and reassemble the RPTO. Separate sections provide procedures for removing and installing the vibration damper and pulley.
The document provides instructions for removing and installing the front housing on a Caterpillar C18 engine. It describes:
1) Removing components like the camshaft position sensor, crankshaft position sensor, engine support, camshaft gear and crankshaft front seal before removing the front housing.
2) Removing bolts to separate the front housing from the cylinder block, and removing the front oil seal from the housing.
3) Cleaning surfaces and installing the front oil seal and housing back onto the cylinder block using thread lock compound on the bolts.
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components such as the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, including attaching various tools and ensuring proper torque for fasteners.
The document provides instructions for removing and installing final drives and the power train oil filter on a D6R track-type tractor. Key steps include using tools to remove the outer axle and final drive from the machine. The final drive planetary carriers can be removed in the chassis. Instructions are also given for disassembling and assembling the final drives and oil filter, which involves removing seals, gears, and other components and cleaning parts before reassembly.
This document provides instructions for disassembling and assembling components of the right planetary and brake, power train oil pump, and other parts of a D6H track-type tractor. It outlines 21 steps to disassemble the right planetary and brake, removing gears, discs, seals, and other parts. It then provides 22 steps to reassemble the components. A separate section provides 12 steps to remove and install the power train oil pump, disconnecting hoses and removing mounting bolts.
This document provides instructions for removing and installing the cylinder head on a Caterpillar 3516B engine used in a 994K wheel loader. The removal process involves draining coolant, removing connecting tubes and bolts, and lifting off the cylinder head. The installation is the reverse, and includes cleaning surfaces, installing new seals and gaskets, and torquing bolts in a specific sequence. Valves, guides, and other components are also removed and installed using various tools as outlined in the procedure.
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3516E engine. It outlines the required tools and gives step-by-step procedures for disassembling and assembling the cylinder head components, including removing and installing the cylinder head, valves, valve guides, valve seat inserts, and valve lifters. Safety notices are provided throughout to warn technicians of potential hazards during disassembly and assembly.
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 992K wheel loader with a C32 engine, including:
1) The crankshaft front seal using various tools to puncture, pry, and remove the seal and sleeve.
2) The front gear group using bolts, plates and shafts.
3) The front housing using bolts, seals and lifting equipment to remove the heavy component.
4) The valve mechanism cover using bolts and seals after loosening breathers and hoses.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 930K WHEEL LOADER EYE
Configuration: 930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
924K, 930K and 938K Wheel Loaders
Media Number -UENR0287-05 Publication Date -01/08/2013 Date Updated -02/11/2017
i04554171
Piston Pump (Steering)
SMCS - 4306; 5070
Removal Procedure
Start By:
a. Remove the cab.
b. Remove the hydrostatic, charge gear pump.
1. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the
correct draining and filling procedures.
Illustration 1 g02723776
2. Disconnect hose assemblies (1).
1/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g02723929
3. Attach a suitable lifting device to steering piston pump (2). The weight of steering piston
pump (2) is approximately 36 kg (80 lb). Remove bolts (3). Use the suitable lifting device in
order to remove steering piston pump (2).
Illustration 3 g02723958
4. Remove coupling (4).
Installation Procedure
1. Install steering piston pump (2) in the reverse order of removal.
a. Tighten bolts (3) to a torque of 215 ± 10 N·m (160 ± 7 lb ft)
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller 1
B 1P-0510 Driver Group 1
2/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Start By:
a. Remove the steering piston pump.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Illustration 4 g01284849
1. Remove bolts (1) and compensator valve (2).
Illustration 5 g01284850
2. Remove gasket (3) from compensator valve (2).
3/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g01284851
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (4), and the O-ring seal.
4. Remove plug (12), and the O-ring seal.
5. Remove valve (10), spool (5), retainer (6), spring (7), spring (8), O-ring seal (9), and screw
assembly (11).
6. Remove valve (17), spool (13), retainer (14), spring (15), spring (16), O-ring seal (18), and
screw assembly (19).
Illustration 7 g01284854
4/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (20) and head (21).
Illustration 8 g02723654
8. Remove O-ring seals (22) and port plate (23) from head (21).
Note: Place identification marks on port plate (23). The port plate must be in the original
position.
Illustration 9 g02724785
9. Remove bearing cup (24) from head (21).
5/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 10. Remove piston guides (25) from head (21), if necessary.
Illustration 10 g02724809
11. Remove spring (26) and piston (27) from pump housing (28).
Illustration 11 g02724811
12. Remove piston (29) from pump housing (28).
13. Remove bearing cone (30) and O-ring seal (31) from pump housing (28).
Note: Bearing cone (30) is a slip fit.
6/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g02724814
14. Remove shim (32) from the pump shaft.
Illustration 13 g02724815
Illustration 14 g02724816
15. Remove rotating group (33) from pump housing (28). Remove shaft assembly (34) with
rotating group (33).
Illustration 15 g02724823
16. Remove swashplate bearings (35) from pump housing (28).
7/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 16 g02723510
17. Rotate pump housing (28). Remove retaining ring (36) from pump housing (28).
Illustration 17 g02724826
18. Remove oil seal (37) from pump housing (28).
Illustration 18 g02724830
19. Remove bearing cup (38) from pump housing (28).
8/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g02724833
20. Remove shaft assembly (34) from rotating group (33).
Illustration 20 g02723519
21. Use a suitable press and Tooling (A) in order to remove bearing cone (39) from shaft
assembly (34).
Illustration 21 g02724921
22. Remove swashplate cradle (40) from rotating group (33).
9/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g02724924
23. Remove piston assemblies (41) from barrel (42).
Note: Place a mark on the piston assemblies and the barrel. The pistons must be returned to
the original position.
Illustration 23 g02724929
24. Remove piston assemblies (41) from retaining plate (43).
Illustration 24 g02724935
25. Remove guide (44) from barrel (42).
10/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 25 g02723526
Illustration 26 g02724942
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
26. Use a suitable press and Tooling (B) to compress the spring in barrel (41).
27. Use Tooling (A) to remove retaining ring (45) from the barrel (42).
28. Remove spring (46), plate (48), and pressure pins (47) from the barrel.
11/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 27 g02724948
29. If necessary, remove stop (49) from swashplate cradle (40).
Assembly Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Group 1
C 8H-8581 Feeler Gauge 1
D 8T-5096 Dial Indicator Gp 1
E 6V-2055 Grease 1
F 9S-3263 Thread Lock Compound 1
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline for Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: Apply a light film of oil to all components before assembly.
12/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 28 g02724948
1. If necessary, install stop (49) in swashplate cradle (40).
Illustration 29 g02724942
Illustration 30 g02723526
Improper assembly of parts that are spring loaded can cause bodily
injury.
13/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install pressure pins (47), plate (48), spring (46), and retaining ring (45) into barrel (42).
3. Use Tooling (B) and a suitable press to compress the spring in barrel (42).
4. Install retaining ring (45) in barrel (42).
Illustration 31 g02724935
5. Install guide (44) on barrel (42).
Illustration 32 g02724929
6. Install piston assemblies (41) in retaining plate (43).
14/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 33 g02724924
7. Install piston assemblies (41) in barrel (42).
Note: Piston assemblies (41) must be installed in the original position.
Illustration 34 g02724921
8. Install swashplate cradle (40) on rotating group (33).
Illustration 35 g02724965
9. Raise the temperature of bearing cone (39) and install the bearing on shaft assembly (34).
15/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 36 g02724826
10. Install oil seal (37) in pump housing (28).
Illustration 37 g02723510
11. Rotate pump housing (28). Install retaining ring (36) into pump housing (28).
Illustration 38 g02724830
12. Lower the temperature of bearing cup (38) and install the bearing cup into pump housing
(28).
16/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 39 g02724823
13. Install swashplate bearings (35) into pump housing (28).
14. Use the following Steps to determine the proper preload on the bearings of the pump
assembly.
Illustration 40 g02724969
a. Install shaft assembly (34) into pump housing (28).
Illustration 41 g02724975
b. Install shim (32) and bearing cone (30) onto shaft assembly (34).
17/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 42 g02724980
c. Lower the temperature of bearing cup (24). Install bearing cup (24) into head (21).
Illustration 43 g02723621
d. Position head (21) onto pump housing (28).
e. Use Tooling (C) in order to measure the distance between the head and the pump
housing.
f. Take measurements at three equal intervals on the surface between the head and the
pump housing.
g. The average of the three dimensions must be 0.00 to 0.05 mm (0.000 to 0.002 inch).
h. Shim (32) must be replaced with a shim of the correct dimension.
18/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 44 g01284854
i. Install bolts (20) in head (21). Tighten bolts (20) to a torque of 55 ± 10 N·m
(41 ± 7 lb ft).
j. Install a bolt into the end of shaft assembly (34).
Illustration 45 g02723632
k. Use Tooling (D) and a screwdriver in order to check for end play in shaft assembly
(34). If end play exists in the pump shaft, repeat Step 14 until the correct dimension is
reached.
l. Remove bolts (20) and head (21) from the pump housing.
m. Remove bearing cone (30) and shim (32) from shaft assembly (34). Remove shaft
assembly (34) from the pump housing.
n. Proceed with the assembly of the pump housing assembly.
19/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 46 g02724833
15. Install shaft assembly (34) into rotating group (33).
Illustration 47 g02724815
16. Carefully turn rotating group (33). Install rotating group (33) into pump housing (28).
Illustration 48 g02724814
17. Install shim (32) onto shaft assembly (34).
20/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 49 g02724811
18. Install O-ring seal (31) onto pump housing (28).
19. Install bearing cone (30) on shaft assembly (34).
20. Install piston (29) into pump housing (28).
Illustration 50 g02724809
21. Install piston (27) and spring (26) into pump housing (28).
Illustration 51 g02724785
21/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 22. Install piston guides (25) in head assembly (21), if necessary. Tighten piston guides (25) to
80 N·m (59 lb ft).
Illustration 52 g02723654
23. Install O-ring seals (22) into head (21).
24. Install port plate (23) onto head (21).
Note: Port plate (23) must be installed in the original position.
Note: Use Tooling (E) in order to secure the port plate to the head assembly during
assembly.
Note: Ensure that the port plate is properly positioned between the head and the pump
housing during this procedure.
Illustration 53 g01284854
Improper assembly of parts that are spring loaded can cause bodily
injury.
22/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Carefully install head (21) onto the pump housing.
26. Apply Tooling (F) to the threads of bolts (20).
27. Install bolts (20) in head (21). Tighten bolts (20) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
Illustration 54 g01284851
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
28. Install screw assembly (19), O-ring seal (18), spring (16), spring (15), retainer (14), spool
(13), and valve (17).
29. Install screw assembly (11), O-ring seal (9), spring (8), spring (7), retainer (6), spool (5),
and valve (10).
30. Install the O-ring seal and plug (12).
31. Install the O-ring seal and plug (4).
23/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 55 g01284850
32. Install gasket (3) onto compensator valve (2).
Illustration 56 g01094312
Illustration 57 g01284849
33. Install compensator valve (2) and bolts (1).
Note: The correct priming and break-in procedures should always be used, when the parts of the
rotating group have been rebuilt or replaced. The break-in procedure is important because
improper break-in will result in failures after minimal hours of the pumps and of the motors.
24/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Improper break-in procedures leave little evidence about the failure. Prime a rebuilt pump or a
rebuilt motor.
Note: Abrasive particles must be removed from the hydraulic system. Contamination is a frequent
cause of pump failures. Pump failures are often due to improper flushing techniques from a
previous failure.
Note: Hydraulic system repair is required if the components have been run to catastrophic failure.
The amount of hydraulic system repair will depend on the extent of metal contamination. Do not
use the kidney loop filtering method as the only cleanup procedure. Refer to Special Instruction,
SMHS6866 for loaders. Refer to Special Instruction, SMHS6936 for excavators. These procedures
can be adapted to the hydraulic systems on other Caterpillar machines. The basic flushing
procedures are similar. Be sure to flush the system thoroughly after a failure. Use 130-6061 Hose
Cleaner Group to assist flushing the hydraulic system. Refer to Tool Operating Manual,
NEHS0643 for information on the 130-6061 Hose Cleaner Group.
Note: Once all contaminants have been thoroughly flushed from the system, a baseline SOS
analysis must be completed. Refer to Special Instruction, SEBF3116 for information on oil
sampling. The SOS oil sample is used to determine the size and the quantity of the contaminants.
Particle count is the recommended method for particle detection.
Note: Use 138-9656 Contamination Counter Group during the cleaning procedure for the
hydraulic system. Clean the hydraulic system for 4 hours. Refer to Tool Operating Manual,
NEHS0580 for information on the 138-9656 Contamination Counter Group .
End By:
a. Install the steering piston pump.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Apr 27 01:10:11 UTC+0800 2020
25/25
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engi...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 930K WHEEL LOADER EYE
Configuration: 930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
924K, 930K and 938K Wheel Loaders
Media Number -UENR0287-05 Publication Date -01/08/2013 Date Updated -02/11/2017
i04705191
Secondary Steering Pump and Electric Motor
SMCS - 4324-GT; 4324-MW; 4324-SE; 4324; 4325-SE; 5073-SST
Specifications
Illustration 1 g02790506
Table 1
Specification for 347-8287 Secondary Steering Pump and Electric Motor Gp
Item Qty Part Specification Description
1 2 1A-2209 Bolt Torque to 37 ± 2 N·m (27 ± 1 lb ft).
1/2
930K Small Wheel Loader EYE00001-UP (MACHINE) POWERED BY C7.1 Engine(...
2020/4/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...