This document provides instructions for removing and installing various components of a Caterpillar C13 diesel engine, including:
- Removing the flywheel housing and installing it in reverse order
- Removing the vibration damper, pulley, and crankshaft front seal and installing them in reverse order
- Removing the front cover, front gear group, and front housing and installing them in reverse order
- Removing brackets and pulleys from the accessory drive and installing them in reverse order
This document provides instructions for removing and installing various components of a Caterpillar C13 engine, including:
- Removing the flywheel housing using link brackets and sealant.
- Removing the vibration damper and pulley using a guide stud.
- Removing the crankshaft front seal by taking off nuts and leaving the shipping sleeve in place for reinstallation.
- Removing the front cover by taking off bolts and studs after removing the accessory drive and vibration damper/pulley.
- Removing the front gear group after removing the front cover by taking off bolts, bearings, shafts and gears.
- Removing the front housing after removing various other components by
This document provides instructions for removing and installing various components of a Caterpillar C13 engine, including:
- Removing the flywheel housing using link brackets and sealant.
- Removing the vibration damper and pulley using a guide stud.
- Removing the crankshaft front seal by taking off nuts and leaving the shipping sleeve in place for reinstallation.
- Removing the front cover by taking off bolts and studs after removing the accessory drive and vibration damper/pulley.
This document provides instructions for removing and installing various components of a C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, accessory drive brackets and pulleys, fumes disposal filter, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions detailing how to remove, install, and properly tighten each component.
The document provides instructions for removing and installing various components of a Caterpillar C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, and accessory drive brackets and pulleys. The procedures include lists of required tools and step-by-step instructions describing how to remove and install each part.
The document provides instructions for removing and installing various components of a Caterpillar C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, accessory drive brackets and pulleys, fumes disposal filter, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions describing how to remove and install each component.
The document provides instructions for removing and installing various components of a Caterpillar C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, accessory drive brackets and pulleys, fumes disposal filter, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions describing how to remove and install each component.
This document provides instructions for removing and installing camshaft and camshaft components on a Caterpillar C13 engine. The procedures include removing and installing the camshaft, camshaft gear, camshaft bearings, engine oil pan, and cylinder liner. Detailed steps are outlined along with required tools and torque specifications. Safety notices are included to ensure proper timing and installation of parts.
This document provides instructions for removing and installing the camshaft and camshaft gear on a Caterpillar C13 engine. It describes the required tools and lists the step-by-step procedures. The camshaft must be removed with the timing marks aligned and lubricated to prevent damage. The camshaft gear is pressed off and requires heating for installation. Camshaft bearings are removed and installed using a specialized tool to set the proper depth.
This document provides instructions for removing and installing various components of a Caterpillar C13 engine, including:
- Removing the flywheel housing using link brackets and sealant.
- Removing the vibration damper and pulley using a guide stud.
- Removing the crankshaft front seal by taking off nuts and leaving the shipping sleeve in place for reinstallation.
- Removing the front cover by taking off bolts and studs after removing the accessory drive and vibration damper/pulley.
- Removing the front gear group after removing the front cover by taking off bolts, bearings, shafts and gears.
- Removing the front housing after removing various other components by
This document provides instructions for removing and installing various components of a Caterpillar C13 engine, including:
- Removing the flywheel housing using link brackets and sealant.
- Removing the vibration damper and pulley using a guide stud.
- Removing the crankshaft front seal by taking off nuts and leaving the shipping sleeve in place for reinstallation.
- Removing the front cover by taking off bolts and studs after removing the accessory drive and vibration damper/pulley.
This document provides instructions for removing and installing various components of a C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, accessory drive brackets and pulleys, fumes disposal filter, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions detailing how to remove, install, and properly tighten each component.
The document provides instructions for removing and installing various components of a Caterpillar C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, and accessory drive brackets and pulleys. The procedures include lists of required tools and step-by-step instructions describing how to remove and install each part.
The document provides instructions for removing and installing various components of a Caterpillar C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, accessory drive brackets and pulleys, fumes disposal filter, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions describing how to remove and install each component.
The document provides instructions for removing and installing various components of a Caterpillar C13 engine, including the flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, front gear group, front housing, accessory drive brackets and pulleys, fumes disposal filter, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions describing how to remove and install each component.
This document provides instructions for removing and installing camshaft and camshaft components on a Caterpillar C13 engine. The procedures include removing and installing the camshaft, camshaft gear, camshaft bearings, engine oil pan, and cylinder liner. Detailed steps are outlined along with required tools and torque specifications. Safety notices are included to ensure proper timing and installation of parts.
This document provides instructions for removing and installing the camshaft and camshaft gear on a Caterpillar C13 engine. It describes the required tools and lists the step-by-step procedures. The camshaft must be removed with the timing marks aligned and lubricated to prevent damage. The camshaft gear is pressed off and requires heating for installation. Camshaft bearings are removed and installed using a specialized tool to set the proper depth.
This document provides instructions for removing and installing camshaft and camshaft components on a Caterpillar C13 engine. The procedures include removing and installing the camshaft, camshaft gear, camshaft bearings, engine oil pan, and cylinder liner. Detailed steps are provided, including required tools and torque specifications. Safety notices are included to ensure proper timing and installation of parts.
Caterpillar cat 322 c fm excavator (prefix m2h) service repair manual (m2h000...fjskekfkemm
This document provides instructions for removing and installing the camshaft idler gear on a Caterpillar 3126B engine. The removal procedure involves removing the front housing, rotating the crankshaft to align timing marks, and then removing bolts, plates and gears. The installation procedure specifies cleaning parts, pressing in the bearing, aligning timing marks and torquing bolts to the specified values. Tools, torque values, and cautions about fluids and contamination are also provided.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two pieces.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pulling tool and applying thread lubricant. It also provides installation instructions and clearance measurements.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic holding tool and removing camshaft bolts and gears. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a bearing pilot tool and measured for proper depth.
- Engine oil pan - removed by draining oil and removing bolts/studs, installed by applying sealant and torquing bolts in sequence.
- Cyl
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the key.
3) Removing camshaft bearings using pulling tools and applying thread lubricant. It also describes installing new bearings.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing in the reverse order applying sealant.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine, including:
- Removing and installing the camshaft, which requires supporting the lifters and using a magnetic holding tool.
- Removing and installing the camshaft gear, which is pressed off the camshaft and requires heating the gear to 600°F during installation.
- Removing and installing the camshaft bearings using a bearing pilot tool to correctly position the bearings during installation.
- Removing and installing the engine oil pan, which requires draining the oil first, removing fasteners and seals, and applying silicone sealant in beads at specified locations during reinstallation.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two pieces.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate. It provides installation instructions and specifies bearing depths.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse order.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse process.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasten
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two pieces.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a pulling tool and applying thread lubricant. It also provides installation instructions and clearance measurements.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
More Related Content
Similar to Caterpillar Cat 735 ARTICULATED TRUCK (Prefix 3T5) Service Repair Manual (3T500001 and up).pdf
This document provides instructions for removing and installing camshaft and camshaft components on a Caterpillar C13 engine. The procedures include removing and installing the camshaft, camshaft gear, camshaft bearings, engine oil pan, and cylinder liner. Detailed steps are provided, including required tools and torque specifications. Safety notices are included to ensure proper timing and installation of parts.
Caterpillar cat 322 c fm excavator (prefix m2h) service repair manual (m2h000...fjskekfkemm
This document provides instructions for removing and installing the camshaft idler gear on a Caterpillar 3126B engine. The removal procedure involves removing the front housing, rotating the crankshaft to align timing marks, and then removing bolts, plates and gears. The installation procedure specifies cleaning parts, pressing in the bearing, aligning timing marks and torquing bolts to the specified values. Tools, torque values, and cautions about fluids and contamination are also provided.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two pieces.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pulling tool and applying thread lubricant. It also provides installation instructions and clearance measurements.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, then reinstalling and applying sealant in beads.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic holding tool and removing camshaft bolts and gears. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a bearing pilot tool and measured for proper depth.
- Engine oil pan - removed by draining oil and removing bolts/studs, installed by applying sealant and torquing bolts in sequence.
- Cyl
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the key.
3) Removing camshaft bearings using pulling tools and applying thread lubricant. It also describes installing new bearings.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing in the reverse order applying sealant.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing bolts and clips, and installing requires applying sealant
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine, including:
- Removing and installing the camshaft, which requires supporting the lifters and using a magnetic holding tool.
- Removing and installing the camshaft gear, which is pressed off the camshaft and requires heating the gear to 600°F during installation.
- Removing and installing the camshaft bearings using a bearing pilot tool to correctly position the bearings during installation.
- Removing and installing the engine oil pan, which requires draining the oil first, removing fasteners and seals, and applying silicone sealant in beads at specified locations during reinstallation.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C and pressing onto the camshaft.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a receiver sleeve tool by pressing in from the rear.
- Engine oil pan - removed by draining oil first, then removing bolts, studs, clips
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two pieces.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate. It provides installation instructions and specifies bearing depths.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse order.
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two people.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a bearing pilot and puller plate tool, then installing new bearings with the same tool.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse process.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with two people. Installation requires ensuring proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasten
This document provides instructions for removing and installing camshaft components on a Caterpillar C13 engine. It describes:
1) Removing the camshaft by supporting the lifters, installing pulling tools, and carefully removing it in two pieces.
2) Removing the camshaft gear using a press and removing the keyway.
3) Removing camshaft bearings using a pulling tool and applying thread lubricant. It also provides installation instructions and clearance measurements.
4) Removing the engine oil pan by draining oil, removing bolts and clips, and installing with new seals in the reverse order.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Camshaft - removal involves supporting lifters with a magnetic tool, removing bolts and gears, and carefully removing the camshaft with support. Installation requires proper timing.
- Camshaft gear - removed using a press and installed by heating to 315°C.
- Camshaft bearings - removed using a puller tool and lubricant, installed using a sleeve tool and measured for proper depth.
- Engine oil pan - removed by draining oil, removing fasteners and components, and installed by applying sealant and torquing fasteners in
Similar to Caterpillar Cat 735 ARTICULATED TRUCK (Prefix 3T5) Service Repair Manual (3T500001 and up).pdf (20)
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix MAB) Service Repair Manual (MAB00001...f8usjejkdmmd
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows the retaining nut to be safely removed with a hydraulic cylinder, releasing the compressed spring.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05351533
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Brackets 2
B 8C-8422 Sealant -
Start By:
A. Remove the flywheel.
B. Remove the crankshaft rear seal.
Illustration 1 g02175589
1/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. If necessary, remove fuel filter base (1) and reposition fuel filter base (1). Remove bracket
(2) .
Illustration 2 g01870417
2. If necessary, remove oil filter base (3) and reposition oil filter base (3). Remove bracket
(4) .
Illustration 3 g01870418
3. Install Tooling (A) and a suitable lifting device to flywheel housing (6). The weight of
flywheel housing (6) is approximately 64 kg (140 lb). Remove bolts (5) and flywheel
housing (6) .
Installation Procedure
1. Install flywheel housing (6) in the reverse order of removal.
a. Apply Tooling (B) to the backside of flywheel housing (6). Install within 10 minutes
of application.
Mon Dec 2 22:50:40 UTC+0800 2019
2/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03542628
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-0514 Guide Stud 1
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Illustration 1 g01870577
2. Remove one of bolts (1). Install Tooling (A). Remove remaining bolts (1) and pulley
assembly (2).
1/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g01870580
3. Remove vibration damper (3).
Installation Procedure
1. Install vibration damper (3) and pulley assembly (2) in reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:51:36 UTC+0800 2019
2/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03542724
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
a. Remove the vibration damper and the pulley.
Illustration 1 g01870637
1. Remove nuts (1) and crankshaft front seal (2).
Installation Procedure
Note: Leave the shipping sleeve in place in order to install the crankshaft front seal. The
crankshaft front seal must be installed dry.
1. Install crankshaft front seal (2) in reverse order of removal.
1/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g01870695
a. Tighten nuts (1) in a numerical sequence.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:52:32 UTC+0800 2019
2/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05351534
Front Cover - Remove and Install
SMCS - 1166-010
Removal Procedure
Start By:
A. Remove the accessory drive.
B. Remove the vibration damper and the pulley.
Illustration 1 g02851277
1. Remove bolts (2) and remove front support (1) .
1/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g01872517
2. Remove bolts (4) and (5).
3. Remove studs (3), front cover (6), and the gasket.
Installation Procedure
1. Install front cover (6) in the reverse order of removal.
a. Tighten bolts (2) to a torque of 105 ± 20 N·m (77 ± 14 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:53:28 UTC+0800 2019
2/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03545506
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Start By:
a. Remove the front cover.
1/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01014874
1. Remove the following items from the front housing: bolt (3), the bearing and shaft (2) and
gear (1).
2. Remove the following items from the front housing: bolt (6), the bearing and shaft (5) and
gear (4).
Installation Procedure
Note: Make sure that the timing marks on the gears are in alignment.
1. Install the gear group in reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:54:24 UTC+0800 2019
2/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i05016499
Housing (Front) - Remove and Install
SMCS - 1151-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 5900 -
Start By:
a. Remove the fuel transfer pump.
b. Remove the engine oil pump.
c. Remove the water pump.
d. Remove the camshaft.
e. Remove the front gear group.
f. Remove the crankshaft position sensor.
1/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01011130
1. Disconnect sensor (1).
2. Attach a suitable lifting device to the lifting bracket on the front of the engine. The weight
of the engine is approximately 680 kg (1500 lb).
3. Remove front engine mount (4).
4. Loosen the oil pan bolts in order to allow the front of the oil pan to drop.
5. Remove bolts (2).
6. Remove front housing (3).
Installation Procedure
1. Install front housing (3) in reverse order of removal.
2/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. a. Apply Tooling (A) in order to fill the space at the cylinder block, front housing (3),
and the oil pan.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:55:19 UTC+0800 2019
3/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03600501
Accessory Drive - Remove and Install - Brackets and Pulleys
SMCS - 1207-010
Removal Procedure
Start By:
a. Remove the alternator.
b. Remove the refrigerant compressor.
Illustration 1 g01924915
1. Remove bolts (5) and bracket (4). Remove bolts (1), nuts (2), and plate assembly (3).
1/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g01924916
2. Remove nut (1) and the clip. Remove bolts (7) and support bracket (8).
Installation Procedure
1. Install the accessory drive in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:56:15 UTC+0800 2019
2/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i04524140
Fumes Disposal Filter - Remove and Install
SMCS - 1317-010
Removal Procedure
Illustration 1 g01917115
1. Loosen hose clamps (1) and (4) . Remove clamp assembly (3) and fumes disposal filter (2) .
2. Remove bracket (5) .
Installation Procedure
1. Install fumes disposal filter (2) in reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:57:11 UTC+0800 2019
1/1
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03533021
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
Illustration 1 g01861337
1. Remove bolts (2) and valve cover (1).
2. Remove isolation seal (3).
Installation Procedure
1/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01861338
Tightening sequence for the valve cover.
1. Install valve cover (1) in reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 2 22:58:07 UTC+0800 2019
2/2
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: ARTICULATED TRUCK
Model: 735 ARTICULATED TRUCK 3T5
Configuration: 735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C13 Engine for Caterpillar Built Machines
Media Number -UENR0131-06 Publication Date -01/05/2015 Date Updated -27/06/2018
i03533151
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve cover.
Illustration 1 g01861473
1. Disconnect harness assembly (1).
1/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01861475
2. Loosen hose clamp (4). Remove bolts (3) and remove breather (2).
Illustration 3 g01861477
3. Remove element (5).
Illustration 4 g01861478
4. Disconnect harness assemblies (6) and (8). Remove valve cover base (7).
2/3
735 Articulated Truck 3T500001-UP (MACHINE) POWERED BY C13 Engine(M009...
2019/12/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...