This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing fasteners, bearings, seals and other components. It then lists 21 steps for reassembly, describing the installation of bearings, seals, gears, pins and other parts in the reverse order of disassembly. Tolerances and torque specifications are provided for correctly installing many components.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fjksekkmsemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It lists 32 steps for disassembly, including removing components like the planetary carrier, thrust washers, and tie rod end. It then lists 14 steps for assembly, such as installing the axle shaft, sun gear, seals and sleeves back into the axle housing. Special notes are included about alignment marks, lubrication groove orientation, and applying threadlocker to seals during assembly.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fusjejfskekfmsme
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It describes 32 steps to disassemble the components which include removing bolts, shafts, gears, seals, bearings and other parts. It then describes 23 steps for reassembling the components in the reverse order, noting specific torque specifications and lubrication requirements. The purpose is to provide a service technician with a procedure for repairing or replacing parts in the final drive and axle housing assembly.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fsejfjskefsmem
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It includes 32 steps for disassembly that remove components like the planetary carrier, gears, seals, bearings and bushings. The 23 step assembly section provides detailed instructions for installing these components in reverse order, noting proper orientation of parts, torque specifications and checks to ensure correct assembly. Lubrication and use of threadlocker is specified.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fujjsekskemme
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It lists 32 steps for disassembly, including removing the planetary carrier, planetary gears, seals, bearings and other components. It then lists 14 steps for reassembly, including installing new seals, bearings, bushings and other parts in the correct orientation and with threadlocker as needed. The goal is to properly contain fluids, mark parts for reinstallation, and reassemble the rear axle housing and steering components.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fujsefkksemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The 33 steps for assembly describe installing new components in the reverse order of disassembly and provide details on lubrication, torque specifications, and alignment marks to ensure proper reassembly. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...ujfdjjkjskkemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The assembly section lists 23 steps for reinstalling these components in reverse order, and provides details on adjusting torque specifications and applying threadlocker to seals. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fjjsefkksemme
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The assembly section lists 23 steps for reinstalling these components in reverse order, and provides details on adjusting torque specifications and applying threadlocker. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...ujdfjjkskkmmde
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The assembly section lists 23 steps to reinstall these components in reverse order, noting proper torque specifications and lubrication points. Tooling required is identified for various removal and installation tasks.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fjksekkmsemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It lists 32 steps for disassembly, including removing components like the planetary carrier, thrust washers, and tie rod end. It then lists 14 steps for assembly, such as installing the axle shaft, sun gear, seals and sleeves back into the axle housing. Special notes are included about alignment marks, lubrication groove orientation, and applying threadlocker to seals during assembly.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fusjejfskekfmsme
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It describes 32 steps to disassemble the components which include removing bolts, shafts, gears, seals, bearings and other parts. It then describes 23 steps for reassembling the components in the reverse order, noting specific torque specifications and lubrication requirements. The purpose is to provide a service technician with a procedure for repairing or replacing parts in the final drive and axle housing assembly.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fsejfjskefsmem
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It includes 32 steps for disassembly that remove components like the planetary carrier, gears, seals, bearings and bushings. The 23 step assembly section provides detailed instructions for installing these components in reverse order, noting proper orientation of parts, torque specifications and checks to ensure correct assembly. Lubrication and use of threadlocker is specified.
Caterpillar cat 436 c backhoe loader (prefix 2br) service repair manual (2br0...fujjsekskemme
This document provides instructions for disassembling and assembling the final drive and axle housing on a 436C backhoe loader. It lists 32 steps for disassembly, including removing the planetary carrier, planetary gears, seals, bearings and other components. It then lists 14 steps for reassembly, including installing new seals, bearings, bushings and other parts in the correct orientation and with threadlocker as needed. The goal is to properly contain fluids, mark parts for reinstallation, and reassemble the rear axle housing and steering components.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fujsefkksemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The 33 steps for assembly describe installing new components in the reverse order of disassembly and provide details on lubrication, torque specifications, and alignment marks to ensure proper reassembly. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...ujfdjjkjskkemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The assembly section lists 23 steps for reinstalling these components in reverse order, and provides details on adjusting torque specifications and applying threadlocker to seals. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fjjsefkksemme
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The assembly section lists 23 steps for reinstalling these components in reverse order, and provides details on adjusting torque specifications and applying threadlocker. Safety information is provided at the beginning regarding fluid spill containment.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...ujdfjjkskkmmde
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The assembly section lists 23 steps to reinstall these components in reverse order, noting proper torque specifications and lubrication points. Tooling required is identified for various removal and installation tasks.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to lift off the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for disassembling and assembling the transmission of a 442D backhoe loader. It lists over 30 required tools and gives step-by-step instructions to disassemble each component of the transmission, including removing gears, bearings, shafts, and housing. The assembly section provides the reverse steps and notes to clean parts and apply oil before reassembling the transmission components.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the flywheel, flywheel housing, and crankshaft rear seal. The flywheel removal procedure involves using a lifting device and bracket to remove bolts and separate the flywheel. The flywheel housing removal requires supporting the engine, removing mounting bolts, and using a lifting device and bracket to remove the housing. Tools and safety precautions are also listed.
This document provides instructions for removing and installing the flywheel housing on a 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and rear of the flywheel housing, and lifting the housing off with tooling. The installation procedure specifies cleaning mating surfaces, positioning the housing with tooling, and tightening mounting bolts to the specified torques. Instructions are also provided for removing and installing the crankshaft front seal and crankshaft pulley.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on 430F Backhoe Loader models. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety warnings are provided to relieve spring pressure before removing or installing spring-loaded components.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure. Diagrams and illustrations are referenced to aid in the instructions.
This document provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and steps to remove the transmission case, drain the oil, and disassemble the various internal components. These include removing gears, shafts, seals, bearings, and other parts using tools like pullers, presses, and retaining ring pliers. Detailed illustrations accompany each step to show how to access and remove the individual transmission components.
This document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine. It describes:
1) Required tools including a crankshaft turning tool and timing pins.
2) Procedures for locking the crankshaft and camshaft, removing gears, and ensuring timing marks are aligned.
3) Instructions for installing idler gear, fuel pump gear, and checking backlash between gears.
CASE IH Quantum 100F Tractor Service Repair Manual (PIN HLRQ010FEJLU00031 and...fuskddmmd
This document is a service manual that provides maintenance and repair information for various Quantum tractor models and their components. It includes sections covering the engine, transmission, axles, hydraulics, electrical systems, and other components. Each section provides detailed information on removal, installation, and repair procedures for the various parts and systems.
The document provides instructions for assembling and disassembling components of a Caterpillar 426F2 backhoe loader, including:
1) Assembling the axle housing by setting bearing preloads and backlash between gears.
2) Installing the drive and steering axle by attaching it to the frame and installing other components.
3) Procedures for removing and installing a transmission solenoid valve by releasing system pressure and disconnecting electrical connectors.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure instructs to first support the engine, remove the top mounting bolts, attach lifting tools to the housing, remove the bottom mounting bolts, and then lift the housing off using the tools. The installation procedure instructs to clean parts, place the housing on the engine and install the bottom mounting bolts first, then the top bolts, tightening them to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and lifting it off of the cylinder block. The installation procedure specifies cleaning mating surfaces, positioning the housing on the cylinder block, and installing mounting bolts with specified torques. Tools required include link brackets for lifting.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing on the cylinder block, and tightening mounting bolts with the specified torque.
The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 diesel engine. The removal procedure involves loosening the breather hose clamp, removing three nuts and washers to detach the valve cover, and removing seals from the valve cover and oil filler cap. The installation procedure involves inspecting components and reversing the removal steps, ensuring proper installation of gaskets and seals.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...fuskddmmd
This document provides instructions for removing the engine from a Case IH WD1903 or WD2303 self-propelled windrower. The steps include draining fluids, disconnecting wiring harnesses and hoses, removing exhaust components and the radiator hood, and detaching mounting hardware to remove the entire engine assembly. Safety precautions are provided throughout regarding hot or pressurized components, supported loads, and proper waste handling.
CASE IH Quantum 100CL Tractor Service Repair Manual (PIN HLRQ010FEJLU00031 an...fuskddmmd
This document is a service manual that provides maintenance and repair information for various Quantum tractor models and their components. It includes sections covering the engine, transmission, axles, hydraulics, electrical systems, and other components. Each section includes subsections for specific systems and parts. The manual also includes contents pages listing the section and subsection numbers and titles.
CASE IH Quantum 110F Tractor Service Repair Manual (PIN HLRQ010FEJLU00031 and...fuskddmmd
This document is a service manual that provides maintenance and repair information for various Quantum tractor models and their components. It includes sections covering the engine, transmission, axles, hydraulics, electrical systems, and other components. Each section includes subsections for specific systems and parts. The manual also includes contents pages listing the section and subsection numbers and titles.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual (M9D00...fuskddmmd
1) The document provides assembly instructions for a transmission on a 140M 2 motor grader model, including 42 steps to assemble various components like clutches, gears, seals, and bearings.
2) It lists required tools and safety notices, and includes illustrations showing the assembly process. Precautions are mentioned regarding cleaning parts and applying lubrication before assembly.
3) Lifting devices and fixtures are required to position heavy components weighing up to 64 kg, and special tools are used to compress springs for parts assembly. Torque specifications are provided for fasteners.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for installing mounting bolts.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to lift off the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for disassembling and assembling the transmission of a 442D backhoe loader. It lists over 30 required tools and gives step-by-step instructions to disassemble each component of the transmission, including removing gears, bearings, shafts, and housing. The assembly section provides the reverse steps and notes to clean parts and apply oil before reassembling the transmission components.
This document provides instructions for removing and installing various components of a Caterpillar 3054 engine, including the flywheel, flywheel housing, and crankshaft rear seal. The flywheel removal procedure involves using a lifting device and bracket to remove bolts and separate the flywheel. The flywheel housing removal requires supporting the engine, removing mounting bolts, and using a lifting device and bracket to remove the housing. Tools and safety precautions are also listed.
This document provides instructions for removing and installing the flywheel housing on a 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and rear of the flywheel housing, and lifting the housing off with tooling. The installation procedure specifies cleaning mating surfaces, positioning the housing with tooling, and tightening mounting bolts to the specified torques. Instructions are also provided for removing and installing the crankshaft front seal and crankshaft pulley.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on 430F Backhoe Loader models. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety warnings are provided to relieve spring pressure before removing or installing spring-loaded components.
This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure. Diagrams and illustrations are referenced to aid in the instructions.
This document provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and steps to remove the transmission case, drain the oil, and disassemble the various internal components. These include removing gears, shafts, seals, bearings, and other parts using tools like pullers, presses, and retaining ring pliers. Detailed illustrations accompany each step to show how to access and remove the individual transmission components.
This document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine. It describes:
1) Required tools including a crankshaft turning tool and timing pins.
2) Procedures for locking the crankshaft and camshaft, removing gears, and ensuring timing marks are aligned.
3) Instructions for installing idler gear, fuel pump gear, and checking backlash between gears.
CASE IH Quantum 100F Tractor Service Repair Manual (PIN HLRQ010FEJLU00031 and...fuskddmmd
This document is a service manual that provides maintenance and repair information for various Quantum tractor models and their components. It includes sections covering the engine, transmission, axles, hydraulics, electrical systems, and other components. Each section provides detailed information on removal, installation, and repair procedures for the various parts and systems.
The document provides instructions for assembling and disassembling components of a Caterpillar 426F2 backhoe loader, including:
1) Assembling the axle housing by setting bearing preloads and backlash between gears.
2) Installing the drive and steering axle by attaching it to the frame and installing other components.
3) Procedures for removing and installing a transmission solenoid valve by releasing system pressure and disconnecting electrical connectors.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure instructs to first support the engine, remove the top mounting bolts, attach lifting tools to the housing, remove the bottom mounting bolts, and then lift the housing off using the tools. The installation procedure instructs to clean parts, place the housing on the engine and install the bottom mounting bolts first, then the top bolts, tightening them to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and lifting it off of the cylinder block. The installation procedure specifies cleaning mating surfaces, positioning the housing on the cylinder block, and installing mounting bolts with specified torques. Tools required include link brackets for lifting.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing on the cylinder block, and tightening mounting bolts with the specified torque.
The document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 3054 diesel engine. The removal procedure involves loosening the breather hose clamp, removing three nuts and washers to detach the valve cover, and removing seals from the valve cover and oil filler cap. The installation procedure involves inspecting components and reversing the removal steps, ensuring proper installation of gaskets and seals.
CASE IH WD1903 Self-Propelled Windrower Service Repair Manual (from PIN YCG66...fuskddmmd
This document provides instructions for removing the engine from a Case IH WD1903 or WD2303 self-propelled windrower. The steps include draining fluids, disconnecting wiring harnesses and hoses, removing exhaust components and the radiator hood, and detaching mounting hardware to remove the entire engine assembly. Safety precautions are provided throughout regarding hot or pressurized components, supported loads, and proper waste handling.
CASE IH Quantum 100CL Tractor Service Repair Manual (PIN HLRQ010FEJLU00031 an...fuskddmmd
This document is a service manual that provides maintenance and repair information for various Quantum tractor models and their components. It includes sections covering the engine, transmission, axles, hydraulics, electrical systems, and other components. Each section includes subsections for specific systems and parts. The manual also includes contents pages listing the section and subsection numbers and titles.
CASE IH Quantum 110F Tractor Service Repair Manual (PIN HLRQ010FEJLU00031 and...fuskddmmd
This document is a service manual that provides maintenance and repair information for various Quantum tractor models and their components. It includes sections covering the engine, transmission, axles, hydraulics, electrical systems, and other components. Each section includes subsections for specific systems and parts. The manual also includes contents pages listing the section and subsection numbers and titles.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual (M9D00...fuskddmmd
1) The document provides assembly instructions for a transmission on a 140M 2 motor grader model, including 42 steps to assemble various components like clutches, gears, seals, and bearings.
2) It lists required tools and safety notices, and includes illustrations showing the assembly process. Precautions are mentioned regarding cleaning parts and applying lubrication before assembly.
3) Lifting devices and fixtures are required to position heavy components weighing up to 64 kg, and special tools are used to compress springs for parts assembly. Torque specifications are provided for fasteners.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for installing mounting bolts.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 436C BACKHOE LOADER 2BR
Configuration: 436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
416C, 426C, 428C, 436C, & 438C BACKHOE LOADERS POWER TRAIN
Media Number -SENR1206-02 Publication Date -01/11/2003 Date Updated -26/02/2018
SENR12060009
Final Drive And Axle Housing (Rear) (All Wheel Steer)
SMCS - 4050-015; 4050-016
Disassemble Final Drive And Axle Housing (Rear) (All Wheel
Steer)
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations
and mandates.
NOTE: For photographic purposes, the all wheel steer axle has been removed from the machine.
1/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTE: The left and right axle housing assemblies are identical. All operations covered in this
section must be performed on both the right and the left axle housing assemblies.
1. Secure axle assembly to tooling (A) prior to starting any work.
2. Loosen plug (1) in final drive and drain oil in suitable container.
2/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 3. Loosen two socket head bolts (2) and separate the planetary carrier (3) from hub (4). Attach
strap and remove carrier (3). Approximate weight is 34 kg (75 lb).
4. Remove snap ring (5).
5. Install tooling (B) and remove planetary gears (6).
6. Remove snap ring (7) and remove thrust washer (8).
3/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Loosen both hex head screws (9) and remove lock plate (10).
8. Using tooling (C) loosen and remove slotted nut (11).
9. Separate internal gear (12) from steering knuckle housing (13).
10. Using tooling (D), separate hub (14) from steering knuckle housing (13).
4/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 11. Remove bearing (15), O-ring (16), and bearing race (17) from hub (14).
12. Turn hub (13) over and pry out seal ring (18) and remove bearing race (19) from bore of hub
(14).
13. Using tooling (C) remove bearing and bearing inner race (20) from steering knuckle housing
(13).
14. Remove snap ring (21).
5/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 15. Remove two thrust washers (22).
16. Measure the the distance (X) between the bottom of adjustment nut (23) and the top of bolt
(24). Record this measurement for assembly purposes and remove nut and bolt (23) and (24).
17. Remove cotter key (25) and loosen castle nut (26).
18. Install tooling (E) remove tie rod end (27) from bore.
6/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 19. Remove four bolts (28). Remove two plastic caps and install two forcing screws.
20. Attach suitable lifting device to steering knuckle housing. Apply pressure to forcing screws
and remove bearing and pin (29) using forcing screws.
21. Install forcing screws to the lower bearing and pin (30) and remove remove second bearing
and pin (30).
7/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTE: It is important to note the placement of shims (33). Retain the proper shim with its
corresponding pin.
22. Separate bearing (31), O-ring (32), shims (33) from pin (29) or (30) on both the top and
bottom for both sides.
23. Remove steering knuckle housing (13) from the axle.
24. Remove seal (34) from steering knuckle housing bore.
NOTE: It may be necessary to destroy seal to remove it.
25. Remove bushing (35) from knuckle housing bore.
NOTE: The direction of the grooves in bushing (35) are important. The direction of these grooves
are important for proper lubrication of the axle shaft. It will be necessary to replace this bushing in
exactly the same manner.
8/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 26. Remove both bearing races (36) and (37) out of the axle housing.
27. Remove axle shaft and sun gear (38) with both universals from the axle housing.
28. Remove snap ring (39) from axle shaft (38).
NOTE: It may be necessary to destroy seal to remove it.
9/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POWE...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 29. Remove seal (40) from axle housing.
NOTE: The direction of the grooves in bushing (35) are important. The direction of these grooves
are important for proper lubrication of the axle shaft. It will be necessary to replace this bushing
with the grooves in the same position.
30. Remove bushing (41) from axle housing.
31. Place alignment marks on the axle housing and the brake housing to insure proper assembly.
Attach suitable lifting device to axle housing (42). Remove sixteen bolts (43) and separate axle
housing (42) from the brake housing. Weight of axle housing is 86 kg (190 lb).
NOTE: It may be necessary to pry the axle housing from the brake housing. There is a locating
spring pin pressed into the mating surface of the brake housing
10/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 32. Place alignment marks on bushing (43) located on the inside portion of axle housing (42).
Carefully remove bushing (43) from the two pins which hold it.
NOTE: The direction and position of the grooves in bushing (43) are important. The direction of
these grooves are important for proper lubrication. It will be necessary to replace this bushing in
exactly the same manner.
Assemble Final Drive And Axle (Rear) (All Wheel Steer)
Fluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection,
maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with
suitable containers before opening any compartment or disassembling any component containing
fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to
collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations
and mandates.
NOTE: For photographic purposes, the all wheel steer axle has been removed from the unit.
NOTE: The left and right axle housing assemblies are identical. All operations covered in this
section must be performed on both the right and the left axle housing assemblies.
NOTE: For purposes of this assembly procedure only one side of the axle is being assembled. The
identical procedure must be performed to both right and left sides of the axle.
11/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 1. Using tooling (A), install sleeve (2) into center bore of axle housing (2). Drive sleeve into the
axle housing until it is flush with thestep in the axle housing.
NOTE: Prior to installation of sleeve (2), insure that the lubrication grooves are in the downward
position in relation to the axle. These grooves are critical for proper lubrication.
12/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 2. Using tooling (A), lubricate and install seal (3) and install it in the center bore of axle housing
(1). Apply some 9S3263 Threadlocker to the outer metal diameter of the seal.
3. Using tooling (B), install outer bearing race (4) into the upper and lower steering knuckle bore.
4. Install sun gear (5) and secure by means of snap ring (6).
13/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Install dust shield (7) and bushing (8) to the axle shaft.
6. Install axle shaft (9) into axle housing (1).
14/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 7. Using tooling (A), install sleeve (10) into bore of steering knuckle hull (11)
NOTE: Prior to installation of sleeve (10), insure that the lubrication grooves are in the downward
position in relation to the axle. These grooves are critical for proper lubrication.
8. Using tooling (A), lubricate and install seal (12) and install it in the center bore of steering
knuckle hull (11). Apply some 9S3263 Threadlocker to the outer metal diameter of the seal.
15/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 9. Assemble upper and lower bearing pins (16) as follows:
a. Install O-ring (15) into groove located in pin (16) under seal cap (14).
b. Install seal cap (14) on pin (16) under bearing (13).
c. Place bearing (13) and assembled pin (16) in a press and press bearing (13) onto pin (16) until
contact is made.
10. Install tooling (C) to steering knuckle hull (11) and lift into position. Fit sun gear (5) portion of
axle shaft through center of steering knuckle hull (11). Insure that bushings and seals are not
dislodged during assembly.
16/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 11. Install original shim (17) under each of the upper pins (16) on each side of the axle. Test the
rolling torque of the steering knuckle hull. The rolling torque should be 23 to 30 N·m (17 to 22 lb
ft).
NOTE: If new bearings are used, installed properly, and a shim of 60mm (.02 in) is used the
proper rolling torque will be achieved.
NOTE: Check the final position of pin (16) prior to final torquing of the bolts. The lubricating
fitting should be facing the center of the axle.
12. Install the proper shim (17) and install pin (16). Install four bolts (18) and tighten to a torque
of 280 N·m (207 lb ft).
NOTE: Recheck rolling torque of steering knuckle hull (11) a final time to insure accuracy.
Lubricate all four bearings.
17/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. 13. Place hub (19) in a press and install bearing race (20) into the hub.
14. Turn hub (19) over in the press. Using tooling (E), press seal (21) into the hub.
NOTE: Apply some 9S3263 Threadlocker to the outer metal diameter of the seal.
15. Heat bearing (22) and install it onto steering knuckle hull until full contact is made.
18/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 16. Install O-ring (22) on hub (19). Lubricate seal (21) inside hub (19). Install assembled hub (19)
onto steering knuckle hull and retain in place with outer bearing (23).
17. Install internal gear (24) onto hub (19).
18. Install slotted nut (25). Insure that chamfered side of slotted nut (25) is facing outward.
19. Adjust the rolling torque of the bearings by use of a spring scale, tooling (F) and tooling (G).
20. Continue to turn hub by use of tooling (F) while at the same time tightening slotted nut (25)
with tooling (G). Rolling torque of the hub should be 27 to 46 N·m (20 to 34 lb ft).
NOTE: If new bearings were used the higher rolling torque value should be used. If bearings were
reused, the lower rolling torque value should be used.
19/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 21. After the proper rolling torque has been attained, install lock plate (26) and two bolts (27) to
secure slotted nut (25). Tighten bolts (27) to a torque of 69 N·m (51 lb ft).
NOTE: Use only new bolts (27) to secure lock plate (26). These bolts can only be properly torque
one time.
22. Install two washers (28) and (29) as shown. The stepped face of the outer washer (29) should
be facing outward.
23. Install snap ring (30) in the groove of the sun gear portion of the axle shaft. This snap ring will
secure washers (28) and (29).
24. Assemble three sets of planetary gears (31) as shown. Heat and install two sets of gears in
planetary gear carrier.
NOTE: It is possible to perform the following calculations with all three planetary gears installed
in the planetary carrier but very difficult. It is recommended that just two planetary gears be
installed at this time.
25. Calculate the end play of the sun gear portion of the axle shaft in the following manner.
20/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. a. Using a depth gauge and tooling (H) measure dimension (I) from the flange mounted surface to
the contact face of the thrust washer. Example Dimension (I) 166.20 mm.
NOTE: Remember to subtract for the thickness of tooling (H).
b. Tilt the drive 90 degrees to the steering axle of the axle housing and push the sun gear in. Using
a depth gauge and tooling (H), determine dimension (II) from the end face of the sun gear shaft to
the flange mounted surface of the hub. Example Dimension (II) 163.10 mm.
NOTE: Remember to subtract for the thickness of tooling (H).
21/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 26. Install required thrust washer (33) and secure it by means of snap ring (32).
27. Heat and install the last planetary gear (31) in the planetary gear carrier and secure with snap
ring.
28. Install planetary gear carrier (35) onto the hub.
NOTE: If the planetary gear carrier does not seat at first, remove and move the planetary gears
slightly so they will mesh with the sun gear.
29. Install two Allen bolts (34) which secure the planetary gear carrier to the hub. Tighten bolts
(34) to a torque of 55 N·m (41 lb ft).
22/23
436C Backhoe Loader Center Pivot, Parallel Lift 2BR01000-UP (MACHINE) POW...
2019/11/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...