This document provides instructions for removing and installing the valve mechanism cover on a Caterpillar 430F2 backhoe loader with a C4.4 engine. It outlines the necessary tools and describes a 7 step process for removal and a 9 step process for installation. Safety notices are included to keep parts clean and prevent damage during the procedure. Diagrams and illustrations are referenced to aid in the instructions.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430F2 BACKHOE LOADER HWG
Configuration: 430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820300
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
Start By:
a. If the Clean Emission Module (CEM) is mounted on the valve mechanism cover. Removal
of the CEM will be necessary in order to access the valve mechanism cover. Refer to
Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" for the
correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02522396
1. Remove bolts (1) and bolts (4) from bracket (2) and bracket (3). Position brackets and
harness assembly away from valve mechanism cover (7).
2. Disconnect the plastic tube assembly (5) from the valve mechanism cover for the crankcase
breather. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the
correct procedure.
3. Remove bolts (6) from valve mechanism cover (7).
4. Remove valve mechanism cover (7) from the cylinder head.
Note: Remove the valve mechanism cover vertically in order to avoid damage to the
electronic unit injectors.
2/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g02522397
5. Remove gasket (8) from valve mechanism cover (7).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g02522397
1. Thoroughly clean all gasket surfaces of valve mechanism cover (7). Clean the gasket
surfaces of the cylinder head.
2. Inspect gasket (8) for damage. If necessary, install a new gasket (8) to valve mechanism
cover (7).
Note: Ensure that the gasket is fully seated into the groove of the valve mechanism cover.
4/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g02522398
5/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g02522396
3. Ensure that harness assemblies (10) are not in contact with rocker arms (11) or cylinder
head (9).
Note: Install the valve mechanism cover vertically in order to avoid damage to the
electronic unit injectors.
4. Position valve mechanism cover (7) onto cylinder head (9). Ensure that harness assemblies
(10) are not trapped during the assembly procedure.
5. Install bolts (6).
6/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 6 g02522516
6. Tighten the bolts in the numerical sequence that is shown in Illustration 6. Tighten the bolts
to a torque of 22 N·m (195 lb in).
Repeat Step 6 in order to ensure correct torque.
7. Position brackets and harness assembly onto the valve mechanism cover. Install bolts (1)
and bolts (4) to bracket (2) and bracket (3).
8. Tighten bolts (1) and bolts (4) 9 N·m (79 lb in).
9. Connect the plastic tube assembly to the valve mechanism cover for the crankcase breather.
Refer to Disassembly and Assembly, "Crankcase Breather - Install" for the correct
procedure.
End By:
a. If necessary, mount the CEM on the valve mechanism cover. Refer to Disassembly and
Assembly, "Support and Mounting (CEM) - Remove and Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 14 08:34:03 UTC+0800 2019
7/7
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430F2 BACKHOE LOADER HWG
Configuration: 430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820301
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 298-5564 T40 Torx Socket 1
C 227-4389 E10 Torx Socket 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
(2)
This Tool is used in the aperture for the electric starting motor.
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover
- Remove and Install" for the correct procedure.
Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 1. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the crankshaft
the safe position. Refer to System Operation, Testing and Adjusting, "Position the Valve Mechanism
Before Maintenance Procedures" for the correct procedure.
Illustration 1 g03703568
2. Use Tooling (B) in order to loosen threaded inserts (2) on all rocker arms (1). Unscrew threaded
inserts (2) on all rocker arms (1) until all valves are fully closed.
Note: Ensure that ALL threaded inserts are fully unscrewed.
2/4
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g03703569
Illustration 3 g03703570
3/4
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g03703575
Sequence for tightening the bolts for the rocker shaft assembly
3. Use Tooling (C) to loosen Torx screws (5) in the reverse numerical order to the tightening sequence.
Refer to the Illustration 4.
4. Loosen Torx screws (4) from sufficiently in order to allow removal of rocker shaft assembly (6).
Note: Note Position (X) of different length Torx screws (4).
5. Remove rocker shaft assembly (5) from the cylinder head. Ensure that rocker shaft assembly (5) does
not come into contact with the electronic unit injector identification tag (7).
6. Place an identification mark on pushrods (6) in order to show the location. Remove the pushrods
from the cylinder head.
Note: Identification will ensure that the pushrods can be reinstalled in the original positions. Do not
interchange the positions of used pushrods.
7. Make a temporary mark on valve bridges (3) in order to show the location and the orientation.
Remove the valve bridges from the cylinder head.
Note: Identification will ensure that the valve bridges can be reinstalled in the original location and
the original orientation. Do not interchange the location or the orientation of used valve bridges.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 14 08:34:59 UTC+0800 2019
4/4
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430F2 BACKHOE LOADER HWG
Configuration: 430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820302
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
a. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Make an identification mark on each rocker arm assembly in order to show the location.
1/3
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: The components must be reinstalled in the original location. Do not interchange
components.
Illustration 1 g03706861
2. Remove the Torx screws from the rocker shaft assembly. Note position of different length
Torx screws for assembly purposes.
3. Remove retaining clip (2) from rocker shaft (6). Remove spring (3) from the rocker shaft.
4. Remove rocker arm assembly (4) for the inlet valve from rocker shaft (6). Remove rocker
arm assembly (5) for the exhaust valve from rocker shaft (6).
Note: The rocker arm assembly for the inlet valve is longer than the rocker arm assembly
for the exhaust valve.
5. Remove retaining clip (7) from rocker shaft (6). Remove spring (8) from the rocker shaft.
2/3
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
16. 6. Remove rocker arm assembly (4) for the exhaust valve from rocker shaft (6). Remove
rocker arm assembly (5) for the inlet valve from rocker shaft (6).
7. Repeat Step 5 through Step 6 in order to remove the remaining rocker arms from rocker
shaft (6).
8. If necessary, follow Step 8.a through Step 8.b in order to remove threaded inserts (1) from
the rocker arms.
a. Make a temporary identification mark on each threaded inserts (1) in order to show
the location.
Note: The components must be reinstalled in the original location. Do not interchange
components.
b. Remove threaded inserts (1) from the rocker arms.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 14 08:35:56 UTC+0800 2019
3/3
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 430F2 BACKHOE LOADER HWG
Configuration: 430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820303
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components are clean and free from wear and damage. Refer to
Specifications, "Rocker Shaft" for more information. If necessary, replace any components
that are worn or damaged.
1/3
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g03706861
2. If necessary, loosely install threaded inserts (1) to rocker arm assembly (4) and rocker arm
assembly (5).
Note: The components must be reinstalled in the original location. Do not interchange
components.
3. Lubricate the bores of rocker arm assembly (4) for the inlet valve and rocker arm assembly
(5) for the exhaust valve and rocker shaft (6) with clean engine oil.
4. Install retaining clip (2) and spring (3) to the front end of rocker shaft (6).
5. Install rocker arm assembly (4) for number one inlet valve to the rocker shaft. Install rocker
arm assembly (5) for number one exhaust valve to rocker shaft (6).
Note: The rocker arm assembly for the inlet valve is longer than the rocker arm assembly
for the exhaust valve. Used components should be installed in the original location.
2/3
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Install retaining clip (7) to rocker shaft (6).
7. Install spring (8) to rocker shaft (6).
8. Install rocker arm assembly (4) for number two inlet valve to the rocker shaft. Install rocker
arm assembly (5) for number two exhaust valve to rocker shaft (6).
Note: The rocker arm assembly for the inlet valve is longer than the rocker arm assembly
for the exhaust valve. Used components should be installed in the original location.
9. Repeat Step 6 through Step 8 in order to assemble the remaining components to rocker shaft
(6).
10. Install the Torx screws to the rocker shaft assembly. Ensure that the different length Torx
screws is installed into the correct position.
End By:
a. Install the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Install" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Nov 14 08:36:53 UTC+0800 2019
3/3
430F2 IT Center Pivot Backhoe Loader HWG00001-UP (MACHINE) POWERED BY...
2019/11/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...