The document provides instructions for installing a transmission on a 434E backhoe loader. It describes 25 steps for the installation, including attaching the transmission assembly with a hydraulic jack, installing mounting hardware, connecting hydraulic and electrical lines, and filling the transmission with oil once installed. Tools required include a jack, jack stands, pins, and tubes for supporting the transmission assembly.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 318 f l excavator (prefix fft) service repair manual (fft0000...fjkskedmme
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, springs, and various seals and plates. Safety warnings are provided to release pressures and contain fluids safely.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...ujfdjjskkemme
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, brakes, differentials, seals and pins. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims are used to achieve proper torque specifications. Springs and pins are installed, applying grease and thread lock as needed.
Caterpillar cat 14 m3 motor grader (prefix n9s) service repair manual (n9s000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M3 motor grader. It lists 51 steps to fully disassemble these components, including removing sprockets, bearings, seals, housings, gears, and other parts. Various tools are required, and weights of removed parts are provided. Detailed illustrations accompany each step to show how to properly disassemble the power train.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 318 f l excavator (prefix fft) service repair manual (fft0000...fjkskedmme
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, springs, and various seals and plates. Safety warnings are provided to release pressures and contain fluids safely.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...ujfdjjskkemme
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, brakes, differentials, seals and pins. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims are used to achieve proper torque specifications. Springs and pins are installed, applying grease and thread lock as needed.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 428 d backhoe loader (prefix mbm) service repair manual (mbm0...ujfjjkskkemmd
1. The document provides step-by-step instructions for assembling the transmission of a 428D Backhoe Loader. It details assembling the various transmission components including gears, shafts, bearings, seals and other parts.
2. The transmission assembly procedure requires various tools and begins with installing bearing cups in the transmission case. It then provides directions for assembling the input shaft, reverse shaft, output shafts and other internal components.
3. The final assembly section instructs installing the transmission case and checking clearances of internal shafts before installing remaining external components and filling the transmission with oil.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (...fujsjefjwerkskemm
This document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of a M318D wheeled excavator. The disassembly procedure involves removing 23 separate parts including carrier housings, planetary gears, thrust washers, retaining rings, and brake discs. The assembly procedure instructs installing these 23 parts in reverse order and includes steps to measure clearances and end play to ensure proper assembly. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque multipliers.
Caterpillar cat 140 h motor grader (prefix 126) service repair manual (126000...fusefjskekkmem
The document provides instructions for disassembling and assembling the final drive of a 140H Motor Grader. It lists 24 steps for disassembly, removing components like the sun gear shaft, planetary carrier, gear assemblies, ring gear, drive shaft, and seals. It then lists 30 steps for assembly, installing these components in reverse order, noting specifics like torque specifications and tool requirements.
Caterpillar cat 966 h wheel loader (prefix a6j) service repair manual (a6j018...fudjsjfekskkem
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 33 steps to assemble a torque converter, detailing each sub-component and specifying torque values for fasteners. It also describes removing the transmission from output transfer gears in 6 steps and disassembling the transmission planetary in 9 steps, identifying required tools and safety precautions.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...ujfjjkskkemmd
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. It describes:
1. Releasing hydraulic pressure before removal.
2. Disconnecting hoses from the lower link assemblies.
3. Removing retaining rings, washers and pins from the lower links.
4. Attaching a lifting device and removing the retaining ring, washers and pin from the other side.
5. Removing the bucket.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 430 d backhoe loader (prefix bml) service repair manual (bml0...fhsjejfsekkkm
The document provides instructions for removing and installing rear axle components on a 430D backhoe loader, including tie rods, the drive and steering axle, final drive, and more. The procedures include using various tools to remove nuts, bolts, pins, brackets, and other hardware. Detailed illustrations accompany each step to show how to properly support, position, and disassemble the various axle components.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 430 d backhoe loader (prefix bml) service repair manual (bml0...fujsekwsxksmem
The document provides instructions for removing and installing tie rods on the rear steering of a 430D backhoe loader. It describes using various tools to remove the tie rod end nut, separate the tie rod from the steering cylinder using heat and a puller, and clean and apply thread lock to reinstall the tie rod. Additional steps include removing the rear axle and final drive components for access.
Caterpillar cat 385 c excavator (prefix jcm) service repair manual (jcm00001 ...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
Caterpillar cat 140 k motor grader (prefix jpa) service repair manual (jpa000...fusjefjskekmem
This document provides instructions for disassembling and assembling the final drive of a 140K Motor Grader. It describes removing over 20 components including the planetary carrier, ring gear, drive shaft, sprockets, bearings and seals. Assembly is the reverse of disassembly with details on installing each part and adjusting shims to ensure proper bearing preload. Tools required include link brackets, a wrench assembly and dial indicator gauge.
Caterpillar cat d9 t track type tractor (prefix rjs) service repair manual (r...ufjsjjkksemme
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components like the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, providing torque specifications for fasteners. Tools required include various link brackets, bolts, a driver group, nut, fixture, and spanner wrench.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It details 25 steps for installing the transmission using various tools, connecting hoses and harnesses, and filling the transmission with oil. It then details 14 steps for removing the parking brake and 11 steps for reinstalling it, noting the proper orientation of parts and applying thread lock compound and loctite to bolts.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 428 d backhoe loader (prefix mbm) service repair manual (mbm0...ujfjjkskkemmd
1. The document provides step-by-step instructions for assembling the transmission of a 428D Backhoe Loader. It details assembling the various transmission components including gears, shafts, bearings, seals and other parts.
2. The transmission assembly procedure requires various tools and begins with installing bearing cups in the transmission case. It then provides directions for assembling the input shaft, reverse shaft, output shafts and other internal components.
3. The final assembly section instructs installing the transmission case and checking clearances of internal shafts before installing remaining external components and filling the transmission with oil.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat m318 d wheeled excavator (prefix d8w) service repair manual (...fujsjefjwerkskemm
This document provides instructions for disassembling and assembling the final drive carriers, hubs, and brakes of a M318D wheeled excavator. The disassembly procedure involves removing 23 separate parts including carrier housings, planetary gears, thrust washers, retaining rings, and brake discs. The assembly procedure instructs installing these 23 parts in reverse order and includes steps to measure clearances and end play to ensure proper assembly. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque multipliers.
Caterpillar cat 140 h motor grader (prefix 126) service repair manual (126000...fusefjskekkmem
The document provides instructions for disassembling and assembling the final drive of a 140H Motor Grader. It lists 24 steps for disassembly, removing components like the sun gear shaft, planetary carrier, gear assemblies, ring gear, drive shaft, and seals. It then lists 30 steps for assembly, installing these components in reverse order, noting specifics like torque specifications and tool requirements.
Caterpillar cat 966 h wheel loader (prefix a6j) service repair manual (a6j018...fudjsjfekskkem
This document provides assembly and disassembly instructions for components of a 966H wheel loader transmission. It includes 33 steps to assemble a torque converter, detailing each sub-component and specifying torque values for fasteners. It also describes removing the transmission from output transfer gears in 6 steps and disassembling the transmission planetary in 9 steps, identifying required tools and safety precautions.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...ujfjjkskkemmd
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. It describes:
1. Releasing hydraulic pressure before removal.
2. Disconnecting hoses from the lower link assemblies.
3. Removing retaining rings, washers and pins from the lower links.
4. Attaching a lifting device and removing the retaining ring, washers and pin from the other side.
5. Removing the bucket.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 430 d backhoe loader (prefix bml) service repair manual (bml0...fhsjejfsekkkm
The document provides instructions for removing and installing rear axle components on a 430D backhoe loader, including tie rods, the drive and steering axle, final drive, and more. The procedures include using various tools to remove nuts, bolts, pins, brackets, and other hardware. Detailed illustrations accompany each step to show how to properly support, position, and disassemble the various axle components.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 430 d backhoe loader (prefix bml) service repair manual (bml0...fujsekwsxksmem
The document provides instructions for removing and installing tie rods on the rear steering of a 430D backhoe loader. It describes using various tools to remove the tie rod end nut, separate the tie rod from the steering cylinder using heat and a puller, and clean and apply thread lock to reinstall the tie rod. Additional steps include removing the rear axle and final drive components for access.
Caterpillar cat 385 c excavator (prefix jcm) service repair manual (jcm00001 ...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
Caterpillar cat 140 k motor grader (prefix jpa) service repair manual (jpa000...fusjefjskekmem
This document provides instructions for disassembling and assembling the final drive of a 140K Motor Grader. It describes removing over 20 components including the planetary carrier, ring gear, drive shaft, sprockets, bearings and seals. Assembly is the reverse of disassembly with details on installing each part and adjusting shims to ensure proper bearing preload. Tools required include link brackets, a wrench assembly and dial indicator gauge.
Caterpillar cat d9 t track type tractor (prefix rjs) service repair manual (r...ufjsjjkksemme
This document provides instructions for disassembling and assembling the torque converter of a D9T track-type tractor. It lists over 40 steps to disassemble components like the torque converter cover, output shaft, stator support, and rotating housing. It then lists over 30 steps for assembling these same components in reverse order, providing torque specifications for fasteners. Tools required include various link brackets, bolts, a driver group, nut, fixture, and spanner wrench.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It details 25 steps for installing the transmission using various tools, connecting hoses and harnesses, and filling the transmission with oil. It then details 14 steps for removing the parking brake and 11 steps for reinstalling it, noting the proper orientation of parts and applying thread lock compound and loctite to bolts.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It details 25 steps for installing the transmission using various tools, connecting hoses and harnesses, and filling the transmission with oil. It then details 14 steps for removing the parking brake and 11 steps for reinstalling it, noting the proper orientation of parts and use of thread locking compound.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It details 25 steps for installing the transmission using various tools, connecting hoses and harnesses, and filling the transmission with oil. It then details 14 steps for removing the parking brake and 11 steps for reinstalling it, noting the proper orientation of parts and use of thread locking compound.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It details 25 steps to install the transmission using various tools, including attaching hoses and electrical connections. It then details 14 steps to remove the parking brake and 11 steps to reinstall it, noting the need to properly adjust lever orientation and spring tension.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It describes 25 steps to install the transmission using various tools, including attaching hoses and electrical connections. It then details 14 steps to remove the parking brake and 11 steps to reinstall it, noting the need to properly adjust lever orientation and spring tension.
The document provides installation instructions for a transmission and parking brake on a 434E backhoe loader. It describes 25 steps to install the transmission using various tools, including attaching hoses and electrical connections. It then details 14 steps to remove the parking brake and 11 steps to reinstall it, noting the need to properly adjust lever orientation and spring tension.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
The document provides instructions for installing the transmission on a 434E backhoe loader. It describes:
1) Using a hydraulic jack to lift and position the transmission assembly.
2) Installing mounting brackets, bolts, and hoses to secure the transmission in place.
3) Connecting electrical harnesses, solenoids, and hydraulic lines to complete the installation.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...uufdjjdjfjkkskm
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. It describes:
1. Releasing hydraulic pressure before removal.
2. Disconnecting hoses from the lower link assemblies.
3. Removing retaining rings, washers and pins from the lower links.
4. Attaching a lifting device and removing the retaining ring, washers and pin from the other side.
5. Removing the bucket.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...fujsefkxswksemm
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. It describes:
1. Releasing hydraulic pressure before removal.
2. Disconnecting hoses from the lower link assemblies.
3. Removing retaining rings, washers and pins from the lower links.
4. Attaching a lifting device and removing the retaining ring, washers and pin from the other side.
5. Removing the bucket.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...fujsekfkksemm
This document provides instructions for removing and installing a bucket on a 428E backhoe loader. The key steps include:
1. Releasing hydraulic pressure from the system
2. Disconnecting hoses from the lower link assemblies
3. Removing retaining rings, washers and pins from the lower links and bucket
4. Lifting the bucket off using tooling and installing the new or repaired bucket requires reassembling in reverse order.
Caterpillar cat 428 e backhoe loader (prefix dxc) service repair manual (dxc0...fujsjefskekm
The document provides instructions for removing and installing an engine on a 428E backhoe loader. It describes using lifting tools to position the engine, installing mounting bolts and other components, connecting wiring harnesses and hoses, and filling fluids once installation is complete. The process involves 48 numbered steps and includes illustrations to clarify each step.
Similar to Caterpillar cat 434 e backhoe loader (prefix sxb) service repair manual (sxb00001 and up) (20)
New holland l221 tier 4 b final [nem479941 ]europe skid steer loader service...fjjsefkksemme
This document provides service information for New Holland skid steer and compact track loaders with Tier 4B diesel engines, including:
- Procedures for draining engine oil and coolant, removing the engine, radiator, and other components.
- Instructions for disconnecting hoses, wiring harnesses, and other connections when removing the engine.
- Notes on safety precautions and tilting the cab prior to engine removal.
New holland cx6090 elevation combine harvesters service repair manualfjjsefkksemme
This document is a service manual for CNH Industrial combine harvesters that provides information on maintenance and repair. It contains over 20 sections covering the various systems of the combines, including the engine, transmission, brakes, hydraulics, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading. Each section includes subsections that provide specific part numbers, descriptions, and repair instructions for components of that system.
Komatsu pc180 lc 7k crawler excavator parts catalogue manual - sn k40001 and upfjjsefkksemme
This document provides part numbers and descriptions for components related to the cooling system of a Komatsu PC180LC-7K excavator with serial number K40001 and up. It includes 52 line items describing the radiator core assembly, radiator sheets, radiator frames, oil cooler, hoses, caps, plugs, bolts, washers, and other components that make up the radiator, oil cooler, and their mounting systems.
This document provides instructions for removing and installing the transmission on a 963 Track Loader. It describes in detail the 27 steps to remove the transmission, which includes draining fluids, disconnecting lines and hoses, removing mounting hardware, and lifting the transmission out. It then describes the 15 steps to install the transmission, which involves placing it back in position, reconnecting all lines and hoses, replacing mounting hardware, and refilling fluids. The overall process is to carefully disconnect and reconnect all transmission components and connections when removing and installing the transmission.
This document provides instructions for servicing components of a 963 Track Loader engine, including:
- Removing and installing the engine oil cooler, describing 11 steps
- Disassembling and assembling the oil filter base, describing 6 steps
- Removing the oil pan and oil pan plate, describing 7 steps for removal and 5 steps for installation
- Removing and installing the oil pump, describing 4 steps for removal and 5 steps for installation, and 10 additional steps for disassembling and assembling the oil pump.
Caterpillar cat 955 l track loader (prefix 13x) service repair manual (13x000...fjjsefkksemme
The document provides instructions for disassembling and assembling various components of a Caterpillar 3304 vehicular engine used in a 955L track loader, including:
- Removing and installing valve lifters, pistons, valves, valve seats, water directors, and valve guides.
- Disassembling and assembling pistons.
The procedures include detailed steps for each component, with pictures to illustrate certain steps. Safety notices are included throughout.
Caterpillar cat 955 k track loader (prefix 71j) service repair manual (71j045...fjjsefkksemme
This document provides instructions for servicing the power train of a Caterpillar 955K track loader, including:
- Checking and adjusting the flexible coupling alignment between the engine and transmission.
- Removing and installing the transmission and torque converter.
- Disassembling and assembling the planetary transmission and torque converter.
- Removing and installing the transmission hydraulic and mechanical controls.
Detailed step-by-step instructions are given for accessing, removing, and installing each component, along with specifications for alignment checks and torque values for fasteners. Potential causes of misalignment are discussed.
Caterpillar cat 953 c track loader (prefix bbx) service repair manual (bbx000...fjjsefkksemme
This document provides instructions for removing and installing track components on a Caterpillar 953C track loader. It describes:
1. Using hydraulic jacks, pins and lift forks to loosen the track and remove the track carrier roller.
2. Installing the track carrier roller by aligning dowels, bolting it in place and adjusting the tracks.
3. Removing track rollers by loosening tracks, removing bolts and lifting them out using a lifting fork.
4. Installing track rollers by positioning them on the frame, tightening bolts and adjusting tracks.
Caterpillar cat 953 b track loader (prefix 5mk) service repair manual (5mk000...fjjsefkksemme
This document provides assembly instructions for a Type I governor used on a 953B track loader powered by a 3116 engine. It describes 19 steps to assemble the governor, including installing various springs, levers, and other components in the proper order and position. Safety notices are included to warn of potential injury from released spring forces. Tools required for the assembly are also listed.
New holland cx6080 elevation combine harvesters service repair manualfjjsefkksemme
This document is a service manual for CNH Industrial combine harvesters and covers the following models: CX5080 Elevation, CX5090 Elevation, CX5090 Laterale, CX5090 Hillside, CX6080 Elevation, and CX6090 Elevation. The manual contains information on the engine, transmission, axles, brakes, hydraulic and electrical systems, attachments, feeding, threshing, separation, cleaning, and unloading systems of the combines. It is organized by major component sections and includes part numbers and specifications.
Caterpillar cat 438 d backhoe loader (prefix bpe) service repair manual (bpe0...fjjsefkksemme
The document provides instructions for assembling the transmission of a 438D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, and seals in their proper order. Tools needed for the assembly are listed. Cleanliness is emphasized and components should be cleaned and oiled before installation. Tolerances for shaft play are provided to check proper assembly. The transmission is then installed in the vehicle and filled with the specified oil.
Caterpillar cat 438 c backhoe loader (prefix 9kn) service repair manual (9kn0...fjjsefkksemme
This document provides instructions for installing a turbocharger on a Caterpillar 3054 engine. It describes:
- Inspecting and installing gaskets before mounting the turbocharger
- Mounting the turbocharger using bolts and nuts
- Connecting oil and air lines with hoses and fittings
- Plugging all openings once installation is complete
The instructions are illustrated with diagrams and include notes about keeping components clean and containing fluids.
Caterpillar cat 438 c backhoe loader (prefix 9kn) service repair manual (9kn0...fjjsefkksemme
This document provides instructions for removing and installing the fuel injection pump and turbocharger on a Caterpillar 3054 engine.
The summary is:
1. The fuel injection pump removal procedure involves removing bolts, nuts, and covers to access the pump, then removing the pump and key.
2. Installing the fuel injection pump requires checking seals, aligning marks, installing bolts and nuts, and setting the pump timing.
3. Removing the turbocharger involves loosening hoses and lines, removing bolts and nuts, and removing the turbocharger and gaskets. Plugging openings is also specified.
New holland cx780 combine harvesters service repair manualfjjsefkksemme
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland b115 backhoe loader service repair manualfjjsefkksemme
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
Caterpillar cat 438 c backhoe loader (prefix 9kn) service repair manual (9kn0...fjjsefkksemme
The document provides instructions for disassembling and assembling Denso alternators for a Caterpillar 438C Backhoe Loader. It describes removing the alternator pulley nut, rear cover bolts, brush holder screws, voltage regulator screws, stator leads, and using a puller to separate the alternator case halves. Reassembly involves installing components in reverse order, pressing the case halves together and securing with bolts. Safety procedures are also outlined for fluid containment and preventing tire explosions.
New holland b100 ctc stage iv tractor loader backhoe service repair manualfjjsefkksemme
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 20 sections covering all major vehicle systems from the engine and transmission to hydraulics, steering, and electrical systems. Each section includes detailed component information, specifications, and repair or replacement procedures.
Caterpillar cat 438 c backhoe loader (prefix 2dr) service repair manual (2dr0...fjjsefkksemme
This document provides instructions for removing and installing an air conditioner compressor group, air conditioner filter, full air conditioner system, and cab from a Caterpillar 438C backhoe loader. It describes disconnecting wiring, removing mounting hardware, and reversing steps for installation. Safety warnings are provided regarding working with refrigerants and pressurized air conditioning systems.
New holland b100 c backhoe loader service repair manualfjjsefkksemme
This document is a service manual that contains instructions and specifications for maintenance and repair of backhoe loaders. It includes sections on safety rules, maintenance, technical specifications, dimensions and performance data. The technical specifications section provides details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets and tires of the backhoe loaders. The document also has sections that provide instructions for removing and installing major components like the engine, transmission, radiator and hood.
Caterpillar cat 438 c backhoe loader (prefix 2dr) service repair manual (2dr0...fjjsefkksemme
The document provides instructions for removing a fuel transfer pump on a Caterpillar 3054 engine. It begins by disconnecting the fuel lines at the fuel injection pump and capping the lines. Then it describes removing three bolts holding fuel lines to the rear of the engine and two bolts securing the fuel filter base. Finally, it discusses removing the fuel filter from the base by draining it first before full removal.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SXB
Configuration: 434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train
Media Number -KENR8037-01 Publication Date -01/05/2014 Date Updated -14/05/2014
i03258323
Transmission (Power Shift) - Install
SMCS - 3030-012-PM
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 180-3034 Jack Stand Gp 4
B
8S-7615 Pin 2
4C-6486 Stand 2
8S-7641 Tube 2
8S-8048 Saddle 2
C 208-5040 Support Tube 1
D 1U-7505 Hydraulic Jack 1
1/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01244138
Illustration 2 g01243675
1. Attach Tooling (D) to transmission assembly (31). The weight of transmission assembly
(31) is approximately 255 kg (562 lb).
2. Use Tooling (D) in order to install transmission assembly (31) .
Illustration 3 g01243966
2/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 3. Remove cable strap (37) from drive plate (38) for the converter.
Illustration 4 g01249112
4. Install bolts (34) .
Illustration 5 g01243880
Illustration 6 g01519366
3/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Install mounts (40) and (43) to each side of transmission assembly (31). Install mounting
bolts (39) and (44). Install bolts (42) and (46) and install nuts (41) and (45) .
Illustration 7 g01243827
Note: Make sure that the holes for bolts (36) are clean and free of oil.
6. Rotate flywheel (35) in order to install bolts (36) .
Illustration 8 g01249114
7. Install cover (33) and bolts (32).
8. Install the transmission oil filter. Refer to Operation and Maintenance Manual,
"Transmission Oil Filter - Replace".
4/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g01243674
9. Install hose (30) to the hydraulic oil tank and install clamp (29). Connect hose assembly
(28) .
Illustration 10 g01243666
10. Move transmission filler tube (25) into position and install clip (27) .
Illustration 11 g01519353
5/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 11. Install bolts (26) that retain transmission filler tube (25) .
12. Connect clip (24) .
Illustration 12 g01659919
13. Position manifold (23). Install bolts (21) .
14. Connect harness assembly (18). Install a new cable strap (19) .
15. Connect hose assemblies (20) and (22) .
Note: Hose assemblies (20) and (22) were installed with the transmission.
Illustration 13 g01519326
16. Connect hose assembly (16) to the right side of the transmission. Connect hose assembly
(17) to the left side of the transmission.
6/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g01243656
17. Install solenoids (11) and (15) and install the plungers. Install nuts (12) and (14). Connect
harness assembly (13) .
Illustration 15 g01243338
18. Connect harness assemblies (8), (9), and (10) .
Illustration 16 g01243334
7/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 19. Connect harness assemblies (1), (2), (3), (4), (5), (6), and (7) .
Illustration 17 g01244175
20. Use Tooling (D) in order to remove Tooling (A) and Tooling (C) .
Note: Do not remove Tooling (A) from the front axle.
21. Install the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) -
Remove and Install".
22. Install the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) -
Remove and Install".
23. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump - Install".
24. Fill the transmission with oil. Refer to Operation and Maintenance Manual, "Transmission
Oil - Change".
Illustration 18 g01244146
8/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g01659918
25. Use Tooling (D) in order to remove Tooling (A) and Tooling (B). Lower the machine to the
ground.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 01:57:06 UTC+0800 2019
9/9434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SXB
Configuration: 434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train
Media Number -KENR8037-01 Publication Date -01/05/2014 Date Updated -14/05/2014
i03205406
Parking Brake - Remove and Install
SMCS - 4267-010
S/N - HXB1-UP
S/N - SXB1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-3597 Wheel Chock 4
Start By:
a. Release the system pressure. Refer to Disassembly and Assembly, "System Pressure -
Release".
1. Use Tooling (A) in order to block the tires and prevent the machine from rolling.
1/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g01117298
2. Remove cover (1).
Illustration 2 g01117303
3. Position the parking brake handle into the released position. Remove cotter pin (2) and pin
(3).
Illustration 3 g01117307
4. Disconnect cable assembly (5) from parking brake lever assembly (4).
Illustration 4 g01518515
2/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 5. Remove clip (7) and pin (8).
6. Remove clip (6). Separate cable assembly (5) from bracket (10). Remove bolts (9). Remove
bracket (10).
Illustration 5 g01692800
7. Loosen nut (12).
8. Remove bolt (11), nut (12), and parking brake (13) as one unit.
9. Remove two bolts (15) (not shown).
10. Remove bracket (14).
11. Remove the parking brake cable through the floorplate in the cab.
Illustration 6 g01692813
3/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
12. Remove spring (16) and brake pads (17).
Illustration 7 g01692814
13. Remove outer nut (18), inner nut (19), washer (20), washer (21), thrust washer (22), lever
(23), boot (24), cam (25), balls (28), retainer (27), sleeve (28), and cam (29).
4/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 8 g01692854
14. Remove plate (30), sleeves (31), sleeves (32), and bolt (34) from plate (33).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 155-3597 Wheel Chock 4
B 155-0695 Thread Lock Compound 1
C - Loctite 542 1
5/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 11 g01694154
Note: Orient lever (23) to Dimension (Z). Dimension (Z) is 60 degrees.
2. Install cam (29), sleeve (28), retainer (27), balls (28), cam (25), boot (24), lever (23), thrust
washer (22), washer (21), washer (20), and inner nut (19).
3. Tighten inner nut (19) to a torque of 13 to 14 N·m (115 to 125 lb in). Loosen inner nut (19)
to 240 degrees to 360 degrees.
4. After inner nut (19) is adjusted, install outer nut (18). Tighten outer nut (18) against inner
nut (19) to a torque of 61 to 75 N·m (45 to 55 lb ft).
Illustration 12 g01692813
Improper assembly of parts that are spring loaded can cause bodily
injury.
7/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
5. Install brake pads (17) and spring (16).
6. Install the parking brake cable through the floorplate in the cab.
Illustration 13 g01692800
8/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 14 g01518586
7. Position bracket (14). Apply Tooling (B) to bolts (15). Install two bolts (15) (not shown).
8. Apply Tooling (C) to the threads of nut (12). Position parking brake (13), nut (12), and bolt
(11) as one unit.
9. Maintain Dimension (X) at 1.0 ± 0.5 mm (0.04 ± 0.02 inch) while you are tightening nut
(12) to a torque of 115 ± 5 N·m (85 ± 4 lb ft).
Illustration 15 g01518515
10. Install bracket (10). Install bolts (9). Tighten bolts (9) to a torque of 45 N·m (33 lb ft).
Connect cable assembly (5) to bracket (10). Install clip (6). Install pin (8) and clip (7).
9/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 16 g01117307
11. Connect cable assembly (5) to parking brake lever assembly (4).
Illustration 17 g01117303
12. Install pin (3) and cotter pin (2).
Illustration 18 g01117298
13. Install cover (1).
14. Adjust the parking brake control. Refer to Operation and Maintenance Manual, "Parking
Brake Control - Adjust".
10/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) ...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 15. Remove Tooling (A).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 01:58:03 UTC+0800 2019
11/11434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) ...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SXB
Configuration: 434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train
Media Number -KENR8037-01 Publication Date -01/05/2014 Date Updated -14/05/2014
i02994221
Drive Shaft (Rear) - Remove and Install
SMCS - 3253-010-RE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 155-3597 Wheel Chock 4
Illustration 1 g01116752
1. Use Tooling (A) in order to block the tires. Remove bolts (1). Discard bolts (1).
1/3434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 2 g01116782
2. Remove bolts (3). discard bolts (3). Remove rear drive shaft (2).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 155-3597 Wheel Chock 4
Illustration 3 g01116782
2/3434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 1. Install rear drive shaft (2). Install new bolts (3). Tighten bolts (3) to a torque of 28 ± 7 N·m
(21 ± 5 lb ft).
Illustration 4 g01116752
2. Install new bolts (1). Tighten bolts (1) to a torque of 28 ± 7 N·m (21 ± 5 lb ft). Remove
Tooling (A).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 26 01:58:58 UTC+0800 2019
3/3434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SXB
Configuration: 434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine
Disassembly and Assembly
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train
Media Number -KENR8037-01 Publication Date -01/05/2014 Date Updated -14/05/2014
i03879206
Tire and Rim (Rear) - Remove and Install
SMCS - 4202-010-RE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9745 Air/Hydraulic Jack Gp 1
B 180-3034 Jack Stand Gp 2
Illustration 1 g01516986
1/6434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. 1. Loosen lug nuts (1). Do not remove lug nuts (1) at this time.
Illustration 2 g01153151
2. Use Tooling (A) in order to raise the rear of the machine. Position Tooling (B) under the
rear axle. Lower the machine onto Tooling (B).
Illustration 3 g01516991
3. Remove bolts (2) from fender (3).
2/6434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 4 g01516993
4. Remove filter (5). Remove bolt (4) and remove fender (3).
Illustration 5 g01517013
5. Attach a suitable lifting device to the rear tire and rim (6). The weight of the rear tire and
rim (6) is approximately 186 kg (410 lb). Remove lug nuts (1) and remove the rear tire and
rim (6).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9745 Air/Hydraulic Jack Gp 1
B 180-3034 Jack Stand Gp 2
C 222-3123 Penetrating Oil 1
3/6434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 6 g01517013
1. Attach a suitable lifting device to the rear tire and rim (6). The weight of the rear tire and
rim (6) is approximately 186 kg (410 lb). Install the rear tire and rim (6).
Note: Ensure that all of the studs and lug nuts (1) are clean and dry.
2. Apply one drop of Tooling (C) to the threads of lug nuts (1). Install lug nuts (1). Do not
tighten lug nuts (1) at this time.
Illustration 7 g01153151
3. Use Tooling (A) in order to raise the rear of the machine. Remove Tooling (B). Lower the
machine onto the ground.
4/6434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 8 g01516986
4. Lower the machine onto the ground. Tighten lug nuts (1) to a torque of 190 ± 40 N·m
(140 ± 30 lb ft). Then, turn lug nuts (3) by an additional 60° ± 5°.
Illustration 9 g01516993
5. Install fender (3) and install bolt (4). Install filter (5).
5/6434E Backhoe Loader SXB00001-UP (MACHINE) POWERED BY C4.4 (MECH) En...
2019/9/26https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...