This document provides instructions for removing and installing an engine oil relief valve on a Caterpillar 434E backhoe loader engine. The removal procedure involves draining fluids, loosening fasteners, and using a telescoping magnet to pull the plunger from the relief valve bore. The installation procedure specifies cleaning components, lubricating the plunger, inserting the plunger and spring into the bore, and applying thread locker before tightening the cap. Special safety notices warn of spring force and proper assembly of spring-loaded parts.
Caterpillar cat 434 e backhoe loader (prefix sef) service repair manual (sef0...ujdfjjkskkmmde
The document provides instructions to remove the engine oil pump from a Caterpillar C4.4 engine. It describes draining the engine oil first. Then it details removing the oil pan, oil pump housing cap, relief valve spring and plunger using a magnetic tool. Proper safety precautions are noted due to the spring force.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and No. 1 crankshaft main bearing cap to access the oil pump.
2. Using retaining ring pliers to remove the retaining ring and idler gear from the idler gear shaft.
3. Removing three bolts to detach the oil pump from the No. 1 main bearing cap.
4. The installation procedure includes applying Loctite, filling the pump with oil, and tightening bolts to the specified torques.
Caterpillar cat 436 c backhoe loader (prefix 1fr) service repair manual (1fr0...fjsjekskekmmme
The document provides instructions for installing and removing the crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes cleaning and lubricating parts, using installation tools to correctly position components, and tightening bolts to the specified torques. Proper installation is important to prevent contamination and ensure long component life. Safety precautions are outlined to contain fluids and dispose of them properly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 430F2 backhoe loader. It describes the required tools and parts, removal procedures which include draining fluids and removing components, and installation procedures which involve cleaning, applying sealant, installing new parts, and tightening to specified torques. The overall goal is to properly remove and reinstall these engine components while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...ufjjdkfkksmme
This document provides instructions for installing and removing the crankshaft front seal on a Caterpillar 3054 engine. It outlines the necessary tools and steps to remove the existing seal using a drill bit and slide hammer puller. It then explains how to clean and lubricate the housing and new seal before pressing the new seal into place using a front seal installer tool. The instructions are intended for use on a 436C backhoe loader with a 3054 engine.
Caterpillar cat 325 c excavator (prefix bkh) service repair manual (bkh00001 ...fjsekkdmme
The document provides instructions for removing and installing pistons, connecting rods, crankshaft main bearings, and the crankshaft in a 3126B engine. Key steps include cleaning parts to prevent contamination, applying anti-seize compound to connecting rod bolts, installing pistons and connecting rods with the proper orientation, checking crankshaft end play, and removing/installing components in the correct order.
Caterpillar cat 436 c backhoe loader (prefix 8tn) service repair manual (8tn0...fksejfjskekmm
This document provides installation instructions for pistons, connecting rods, and connecting rod bearings in a Caterpillar 3054 engine. It includes the following key steps:
1. Clean and lubricate the components with engine oil before installation.
2. Align piston rings and insert the piston and connecting rod assembly into the cylinder, ensuring the arrow marks face the front of the engine.
3. Install the connecting rod caps with bolts and nuts and tighten to the specified torque.
4. Use a tool to check piston height and complete installation by adding other engine components like the oil pump and cylinder head.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing a camshaft gear on a Caterpillar 3054 engine. It describes:
1) Rotating the crankshaft to align timing marks and removing the bolt and washer from the camshaft gear.
2) Using a puller tool to remove the camshaft gear and inspecting it for wear or damage.
3) Installing the camshaft gear, checking that the timing marks are aligned, and tightening the bolt.
Caterpillar cat 434 e backhoe loader (prefix sef) service repair manual (sef0...ujdfjjkskkmmde
The document provides instructions to remove the engine oil pump from a Caterpillar C4.4 engine. It describes draining the engine oil first. Then it details removing the oil pan, oil pump housing cap, relief valve spring and plunger using a magnetic tool. Proper safety precautions are noted due to the spring force.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 3054 engine. It describes:
1. Removing the engine oil pan, front housing, and No. 1 crankshaft main bearing cap to access the oil pump.
2. Using retaining ring pliers to remove the retaining ring and idler gear from the idler gear shaft.
3. Removing three bolts to detach the oil pump from the No. 1 main bearing cap.
4. The installation procedure includes applying Loctite, filling the pump with oil, and tightening bolts to the specified torques.
Caterpillar cat 436 c backhoe loader (prefix 1fr) service repair manual (1fr0...fjsjekskekmmme
The document provides instructions for installing and removing the crankshaft rear seal and flywheel housing on a Caterpillar 3054 engine. It describes cleaning and lubricating parts, using installation tools to correctly position components, and tightening bolts to the specified torques. Proper installation is important to prevent contamination and ensure long component life. Safety precautions are outlined to contain fluids and dispose of them properly.
The document provides instructions for removing and installing camshaft bearings, engine oil pans, and piston cooling jets on a Caterpillar 430F2 backhoe loader. It describes the required tools and parts, removal procedures which include draining fluids and removing components, and installation procedures which involve cleaning, applying sealant, installing new parts, and tightening to specified torques. The overall goal is to properly remove and reinstall these engine components while taking precautions to contain fluids and prevent contamination.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...ufjjdkfkksmme
This document provides instructions for installing and removing the crankshaft front seal on a Caterpillar 3054 engine. It outlines the necessary tools and steps to remove the existing seal using a drill bit and slide hammer puller. It then explains how to clean and lubricate the housing and new seal before pressing the new seal into place using a front seal installer tool. The instructions are intended for use on a 436C backhoe loader with a 3054 engine.
Caterpillar cat 325 c excavator (prefix bkh) service repair manual (bkh00001 ...fjsekkdmme
The document provides instructions for removing and installing pistons, connecting rods, crankshaft main bearings, and the crankshaft in a 3126B engine. Key steps include cleaning parts to prevent contamination, applying anti-seize compound to connecting rod bolts, installing pistons and connecting rods with the proper orientation, checking crankshaft end play, and removing/installing components in the correct order.
Caterpillar cat 436 c backhoe loader (prefix 8tn) service repair manual (8tn0...fksejfjskekmm
This document provides installation instructions for pistons, connecting rods, and connecting rod bearings in a Caterpillar 3054 engine. It includes the following key steps:
1. Clean and lubricate the components with engine oil before installation.
2. Align piston rings and insert the piston and connecting rod assembly into the cylinder, ensuring the arrow marks face the front of the engine.
3. Install the connecting rod caps with bolts and nuts and tighten to the specified torque.
4. Use a tool to check piston height and complete installation by adding other engine components like the oil pump and cylinder head.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing a camshaft gear on a Caterpillar 3054 engine. It describes:
1) Rotating the crankshaft to align timing marks and removing the bolt and washer from the camshaft gear.
2) Using a puller tool to remove the camshaft gear and inspecting it for wear or damage.
3) Installing the camshaft gear, checking that the timing marks are aligned, and tightening the bolt.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor which involve installing components like the shaft assembly, cam plate, barrel assembly, brake piston and head in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar cat 236 b skid steer loader (prefix hen) service repair manual (h...ufjjsjekksemmd
This document provides instructions for removing the cylinder head from a Caterpillar 236B Skid Steer Loader engine. The procedure involves draining coolant, disconnecting hoses, removing accessories attached to the head like the exhaust manifold and fuel injectors. Bolts are then loosened in a specified sequence before being removed. Lifting devices are attached to lift the heavy cylinder head off without damaging surfaces. The gasket and dowel pins are also removed.
Caterpillar cat 420 d backhoe loader (prefix bkc) service repair manual (bkc0...ujfjjskkemm
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 3054C diesel engine. It outlines the necessary tools, safety precautions, and step-by-step procedures for removing the cylinder head, installing a new gasket, and torquing the bolts to the proper specifications. Instructions are also provided for removing the camshaft, installing it, and completing reassembly of related components.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and servicing components of a 436B backhoe loader engine, including:
1) Removing the cylinder head by first removing other components and then gradually loosening and removing 22 bolts.
2) Disassembling the rocker shaft by removing retaining rings and disassembling the shaft, arms, and brackets.
3) Reassembling the rocker shaft by lubricating parts and installing them in the correct order onto the shaft.
4) Installing the rocker shaft and pushrods by positioning them correctly and adjusting valve lash.
Caterpillar cat 320 c excavator (prefix bea) service repair manual (bea00001 ...jjdjfkkskemme
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fjjksekksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves draining oil, removing mounting screws and pipes, and removing the pump assembly. Installation requires cleaning, inspecting parts, lubricating with oil, and securing everything with screws.
Removing the water pump requires draining coolant, loosening hoses and clamps, and removing mounting screws. Installation involves installing a new gasket, securing with screws treated with sealant or locktite, filling the system, and reattaching hoses.
Removal of the water temperature regulator involves draining cool
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...fujsekfkksemm
The document provides instructions to remove and install an engine oil relief valve and engine oil pump on a 428E backhoe loader. The summary is:
1. The removal procedure describes removing the engine oil pan, suction pipe, cap, spring, and plunger from the oil relief valve housing.
2. The installation procedure describes cleaning and lubricating parts, installing the plunger, spring, and cap onto the relief valve housing and tightening to the specified torque.
3. The oil pump removal procedure describes removing bolts and pipes to detach the pump from the engine block. The installation procedure describes cleaning parts, installing dowels and bolts to attach the pump and checking backlash with tools.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...ujfjjkskkemmd
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...fujsefkxswksemm
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...uufdjjdjfjkkskm
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleaning and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...fujsjefskekm
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Torque specifications are provided for the bolts.
New holland tc5.30 combine harvesters service repair manualfujsefkksemm
The document is a service manual that provides instructions for removing and installing various engine components on a TC5.30 combine. It includes sections on the engine, clutch, transmission, front and rear axles, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage. The manual uses a coding system to uniquely identify each technical procedure and includes specifications, functional descriptions, diagnostics, and service instructions.
New holland cx780 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland l230 tier 4 skid steer loader service repair manual [ncm449907 ]fujsefkksemm
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland b115 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 ctc stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all major systems of the machines from the engine and transmission to hydraulics, steering, and electrical systems. Each section provides information for servicing components and repairing issues. Safety rules are also outlined to prevent personal injury and machine damage while working.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor which involve installing components like the shaft assembly, cam plate, barrel assembly, brake piston and head in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar cat 236 b skid steer loader (prefix hen) service repair manual (h...ufjjsjekksemmd
This document provides instructions for removing the cylinder head from a Caterpillar 236B Skid Steer Loader engine. The procedure involves draining coolant, disconnecting hoses, removing accessories attached to the head like the exhaust manifold and fuel injectors. Bolts are then loosened in a specified sequence before being removed. Lifting devices are attached to lift the heavy cylinder head off without damaging surfaces. The gasket and dowel pins are also removed.
Caterpillar cat 420 d backhoe loader (prefix bkc) service repair manual (bkc0...ujfjjskkemm
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 3054C diesel engine. It outlines the necessary tools, safety precautions, and step-by-step procedures for removing the cylinder head, installing a new gasket, and torquing the bolts to the proper specifications. Instructions are also provided for removing the camshaft, installing it, and completing reassembly of related components.
Caterpillar cat 436 b backhoe loader (prefix 7fl) service repair manual (7fl0...fjsjekskekmmme
This document provides instructions for removing and servicing components of a 436B backhoe loader engine, including:
1) Removing the cylinder head by first removing other components and then gradually loosening and removing 22 bolts.
2) Disassembling the rocker shaft by removing retaining rings and disassembling the shaft, arms, and brackets.
3) Reassembling the rocker shaft by lubricating parts and installing them in the correct order onto the shaft.
4) Installing the rocker shaft and pushrods by positioning them correctly and adjusting valve lash.
Caterpillar cat 320 c excavator (prefix bea) service repair manual (bea00001 ...jjdjfkkskemme
This document provides instructions for removing a bucket cylinder from an excavator. It begins by noting the importance of relieving pressure from hydraulic systems before disassembly to prevent injury. The steps include releasing hydraulic pressure, attaching lifting devices, removing retaining bolts and pins, and disconnecting hoses. Identification marks should be made on all lines and components. Cleanliness is important during disassembly and reassembly to prevent contamination of hydraulic systems.
Caterpillar cat 442 e backhoe loader (prefix eme) service repair manual (eme0...fjjksekksemm
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 3054C engine.
The procedure for removing the engine oil pump involves draining oil, removing mounting screws and pipes, and removing the pump assembly. Installation requires cleaning, inspecting parts, lubricating with oil, and securing everything with screws.
Removing the water pump requires draining coolant, loosening hoses and clamps, and removing mounting screws. Installation involves installing a new gasket, securing with screws treated with sealant or locktite, filling the system, and reattaching hoses.
Removal of the water temperature regulator involves draining cool
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...fujsekfkksemm
The document provides instructions to remove and install an engine oil relief valve and engine oil pump on a 428E backhoe loader. The summary is:
1. The removal procedure describes removing the engine oil pan, suction pipe, cap, spring, and plunger from the oil relief valve housing.
2. The installation procedure describes cleaning and lubricating parts, installing the plunger, spring, and cap onto the relief valve housing and tightening to the specified torque.
3. The oil pump removal procedure describes removing bolts and pipes to detach the pump from the engine block. The installation procedure describes cleaning parts, installing dowels and bolts to attach the pump and checking backlash with tools.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump, water pump, and water temperature regulator on a Caterpillar 442E backhoe loader engine. The procedures describe draining fluids, removing fasteners and hoses, cleaning components, installing new seals and fasteners, and refilling fluids. Safety notices are provided regarding containing fluids, wearing protective equipment, and inspecting parts for wear.
This document provides instructions for removing and installing the engine oil pump on Caterpillar 3054C engines without a balancer. It describes:
1. Removing the oil pan, suction pipe, and setscrews to detach the oil pump assembly from the cylinder block.
2. Inspecting internal oil pump components and replacing the entire pump if worn or damaged.
3. Cleaning and lubricating oil pump parts before installing, checking clearances, and refilling with oil.
4. Reattaching the oil pump to the cylinder block and reinstalling other parts in reverse order of removal.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...ujfjjkskkemmd
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...fujsefkxswksemm
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleanup and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...uufdjjdjfjkkskm
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Proper cleaning and alignment of parts is emphasized to prevent contamination and ensure correct assembly.
Caterpillar cat 428 e backhoe loader (prefix dph) service repair manual (dph0...fujsjefskekm
This document provides instructions for removing and installing an engine water pump on a 428E backhoe loader. The removal procedure involves draining coolant, removing hoses and bolts, and removing the water pump. The installation procedure specifies cleaning parts, installing a new joint, aligning the water pump using guide bolts, and reinstalling bolts. Torque specifications are provided for the bolts.
Similar to Caterpillar cat 434 e backhoe loader (prefix sef) service repair manual (sef00001 and up) (11)
New holland tc5.30 combine harvesters service repair manualfujsefkksemm
The document is a service manual that provides instructions for removing and installing various engine components on a TC5.30 combine. It includes sections on the engine, clutch, transmission, front and rear axles, brakes, hydraulic systems, steering, wheels, cab climate control, electrical systems, attachments, product feeding, threshing, separation, cleaning, and crop storage. The manual uses a coding system to uniquely identify each technical procedure and includes specifications, functional descriptions, diagnostics, and service instructions.
New holland cx780 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland agricultural vehicle. The system uses a closed-center load sensing pump to supply oil to circuits for steering, header height control, straw elevator functions, lateral flotation, reel adjustment, and unloading tube control. Key components include hydraulic pumps and motors, valves, cylinders, filters, accumulators, and manifolds.
New holland l230 tier 4 skid steer loader service repair manual [ncm449907 ]fujsefkksemm
This service manual provides instructions for servicing engines and components for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders including removing the engine by draining fluids, disconnecting electrical components and hoses, removing covers and cooling components, and then lifting out the engine. Specific models and replacement part numbers are listed for each component. Safety warnings are provided throughout regarding personal safety and relieving hydraulic pressure before working on the machine.
New holland b115 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 ctc stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains over 200 sections covering all major systems of the machines from the engine and transmission to hydraulics, steering, and electrical systems. Each section provides information for servicing components and repairing issues. Safety rules are also outlined to prevent personal injury and machine damage while working.
New holland cx5090 laterale combine harvesters service repair manualfujsefkksemm
This document is a service manual for CNH Industrial combine harvesters. It contains over 200 sections organized by major vehicle systems. The sections provide information on maintenance, repair and replacement of components for the engine, transmission, axles, hydraulics, electrical systems, cab climate control, attachments/headers, product feeding, threshing, separation, cleaning, and crop storage/unloading systems. The manual applies to several CX5000 and CX6000 series combine harvester models.
New holland b100 c backhoe loader service repair manualfujsefkksemm
This document is a service manual that contains instructions and specifications for maintenance and repair of backhoe loaders. It includes sections on safety rules, maintenance, technical specifications, dimensions and performance data. The technical specifications section provides details on the diesel engine, transmission, axles, brakes, steering, hydraulic system, buckets and tires of the backhoe loaders. The document also has sections that provide instructions for removing and installing major components like the engine, transmission, radiator and hood.
New holland cx820 combine harvesters service repair manualfujsefkksemm
The document provides an overview and component locations of the primary hydraulic power system for a New Holland CX combine harvester model. The key components include a closed-center load sensing variable displacement pump that supplies oil to circuits in the main frame stack valve and straw elevator stack valve. These circuits control functions like header height, unloading tube, straw elevator, reel adjustment, and lateral flotation. Hydraulic motors and cylinders powered by the system perform tasks like steering, header lifting, and reel operation.
New holland cx6.90 laterale fpt cursor 9 tier 4 b stage ivstage iv combine ha...fujsefkksemm
This service manual provides maintenance and repair information for several CNH combine models including the CX5.80, CX5.90, CX6.80, and CX6.90. The manual contains over 200 sections covering topics such as the engine, transmission, hydraulic systems, electrical systems, attachments/headers, product feeding, threshing, separation, cleaning, and unloading. Each section provides technical specifications, descriptions of operation, troubleshooting information, and repair instructions for the various components and systems.
New holland br6090 round balers service repair manualfujsefkksemm
This document is a service manual that contains information on maintenance and repair for BR6080 and BR6090 machines. It includes sections on hydraulic, pneumatic, electrical, and electronic systems, as well as chapters on power production, power train, travel, crop processing, and more. Safety protocols are provided, including warnings to only allow trained technicians to perform repairs and to always stop engines and relieve pressures before working on the machines.
New holland b110 backhoe loader service repair manualfujsefkksemm
The document provides instructions for inspecting and disassembling/assembling torque converters for backhoe loaders. It describes inspecting the converter hub splines and welds for wear or damage, and replacing the converter or drive plate if issues are found. The disassembly process involves removing the drive plate screws and plates and then the converter. Reassembly requires installing the converter on the input shaft, then the drive plates with screws tightened to a specified torque.
New holland b100 clr stage iv tractor loader backhoe service repair manualfujsefkksemm
This document is a service manual for various tractor loader backhoe models including the B100C, B110C, and B115C. It contains information on engine systems, transmission, axles, brakes, hydraulics, frames, steering, wheels, cab climate control, and electrical systems. The manual provides part numbers and repair instructions for maintenance and troubleshooting of components.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h036...fujsefkksemm
This document provides instructions for servicing a 951B/C track loader. It discusses general instructions for disassembly and assembly including safety, cleanliness, removal and installation of parts, cleaning and handling of parts, and procedures for reassembling components. It also describes recommended service tools and procedures for pressing parts, applying proper bolt torque, and using torque wrenches and extensions.
Caterpillar cat 432 f backhoe loader (prefix sej) service repair manual (sej0...fujsefkksemm
This document provides instructions for removing and installing inlet and exhaust valve springs on a 432F BACKHOE LOADER model with a C4.4 engine. The procedure involves using special tools to compress the valve springs, rotate the crankshaft to position the piston, and remove/install the valve spring retainers and springs. Proper cleaning and inspection of parts is emphasized to prevent contaminants from causing premature wear.
Caterpillar cat 432 f backhoe loader (prefix pxr) service repair manual (pxr0...fujsefkksemm
This document provides assembly instructions for the axle housing of a 432F backhoe loader. It outlines 34 steps to assemble components like bearings, seals, brakes and differentials. Special tools are required and cleanliness is important during assembly. Measurements are taken and shims selected to achieve proper torque specifications. Springs and pins are installed and nuts are staked to complete the assembly.
Caterpillar cat 432 f backhoe loader (prefix lnr) service repair manual (lnr0...fujsefkksemm
This service repair manual provides instructions for assembling the transmission of a 432F backhoe loader. It lists the required tools and presents a step-by-step procedure with illustrations. Some key steps include installing bearings, seals, gears, shafts, springs, and pistons into the transmission case. Precautions are given for working with compressed springs. The transmission components are assembled in sections, including the input shaft, reverse shaft, direct drive shafts, and output shafts.
Komatsu pc138 us 8 crawler excavator parts catalogue manual - sn 20001-24509fujsefkksemm
This document provides parts information for a PC138US-8 excavator with serial numbers 20001-24509. It includes lists of engine, cooling system, and other parts with part numbers, names, quantities, and applicable serial number ranges. The cooling system section includes radiator, oil cooler, after cooler, fuel cooler, piping, sub tank, and radiator mount parts.
Caterpillar cat 951 b track loader (prefix 69h) service repair manual (69h018...fujsefkksemm
This document provides instructions for servicing a 951B track loader model. It discusses general instructions for disassembly and assembly including safety procedures, cleaning parts, removal and installation techniques, and operating a rebuilt engine. It also describes various service tools such as pullers, push-pullers, and procedures like pressing parts, bolt torque, and using a torque wrench with an extension.
Caterpillar cat 432 e backhoe loader (prefix rxs) service repair manual (rxs0...fujsefkksemm
This document provides instructions for removing and installing an engine on a 432E backhoe loader. The removal process involves 50 steps that disconnect wiring harnesses, hoses, tubes, and remove mounting hardware. The installation is the reverse of removal, involving reconnecting all components and tightening mounting bolts to the specified torques. Special tools are required to lift and support the heavy engine assembly during removal and installation.
Caterpillar cat 438 c backhoe loader (prefix 1tr) service repair manual (1tr0...fujsefkksemm
This document provides instructions for disassembling and assembling the final drive and axle housing on a 438C backhoe loader. It lists 32 steps for disassembly, including draining fluids, removing gears, bearings, seals, and other components. The 33 steps for assembly describe installing new components in the reverse order of disassembly and provide details on lubrication, torque specifications, and alignment marks to ensure proper reassembly. Safety information is provided at the beginning regarding fluid spill containment.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i06801068
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container. Refer to Operation and
Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
2. Drain the engine lubricating oil into a suitable container. Refer to Operation and
Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
1/3434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. If necessary, remove the electric starting motor. Refer to Disassembly and Assembly,
"Electric Starting Motor - Remove and Install".
Illustration 1 g01343557
Typical example
Illustration 2 g06118967
2/3434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Tightening sequence for the engine oil cooler
4. Loosen fasteners (7) in reverse numerical order to the sequence that is shown in Illustration
2. Remove fasteners (7). Support the assembly of engine oil cooler (1) as the fasteners are
removed.
Note: fasteners (7) are different lengths. Note the correct position of the fasteners. Note the
position of any brackets that are secured by the fasteners. Do not remove fasteners (6) .
5. Remove the assembly of oil cooler (1) from the cylinder block.
6. Remove joint (2).
7. Follow Steps 7.a through 7.c to disassemble the engine oil cooler.
a. Remove bolts (6).
b. Remove cooler matrix (3) from housing (5).
c. Remove joints (4).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:49:21 UTC+0800 2019
3/3434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i06801078
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01347869
Typical example
1. Follow Steps 1.a through 1.c to assemble the engine oil cooler.
a. Ensure that cooler matrix (3) is clean and free from damage. Ensure that housing (5)
is clean and free from damage.
b. Position new joints (4) onto housing (5). Install cooler matrix (3).
c. Install bolts (6). Tighten the bolts to a torque of 22 N·m (16 lb ft).
2. Clean the mating surface of the cylinder block.
2/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 2 g06119773
Typical example
3. Position a new joint (2) on the assembly of engine oil cooler (1). Install fasteners (7) to
positions (X) on the assembly of engine oil cooler (1).
Note: The holes in the joint have serrations that hold the fasteners captive.
4. Install the assembly of engine oil cooler (1) to the cylinder block. Tighten bolts (7) finger
tight.
Note: The fasteners are different lengths. Ensure that the different fasteners are installed in
the correct location. Ensure that any brackets that are secured by the fasteners are installed
in the correct location.
Illustration 3 g06118967
3/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Tightening sequence for the engine oil cooler
5. Install remaining fasteners (7) into engine oil cooler (1). Tighten the fasteners to a torque of
22 N·m (16 lb ft). Tighten the fasteners in the sequence that is shown in Illustration 3.
6. If necessary, Install the electric starting motor. Refer to Disassembly and Assembly,
"Electric Starting Motor - Remove and Install".
7. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change" for the correct procedure.
8. Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual,
"Engine Oil Filter and Change" for the correct procedure.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:50:08 UTC+0800 2019
4/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763419
Engine Oil Relief Valve - Remove and Install - Engines with a
Balancer Unit
SMCS - 1315-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly , "Engine Oil Pan -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a
released spring force.
1/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 1 g01343600
Typical example
1. Loosen cap (2). Carefully remove the cap from balancer (1).
Note: The spring force will be released when the cap is removed.
2. Remove spring (3) from the bore for the relief valve in balancer (1).
3. Use Tooling (A) in order to remove plunger (4) from the bore for the relief valve in balancer
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
2/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. B - Loctite 577 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01343600
Typical example
1. Ensure that all components are clean and free from wear or damage. If necessary, replace
any components that are worn or damaged. If the bore for the relief valve in balancer (1) is
worn or damaged, the complete assembly of the balancer must be replaced.
Improper assembly of parts that are spring loaded can cause bodily
injury.
3/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate plunger (4) with clean engine oil. Install plunger (4) and spring (3) into the bore
for the relief valve in balancer (1).
Note: The plunger must slide freely in the bore for the relief valve.
3. Apply Tooling (B) to the threads of cap (2). Install cap (2) to balancer (1). Tighten the cap
to a torque of 21 N·m (15.5 lb ft).
Note: Ensure that the spring is properly located inside the plunger and the cap. Ensure that
Tooling (B) does not contaminate the bore for the relief valve in balancer (1).
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:50:56 UTC+0800 2019
4/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763421
Engine Oil Relief Valve - Remove and Install - Engines
Without a Balancer Unit
SMCS - 1315-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7262 Telescoping Magnet 1
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from being struck by parts propelled by a
released spring force.
1/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 1 g01343561
Typical example
1. Remove bolts (6) and suction pipe (7).
2. Remove the joint from suction pipe (5) (not shown).
3. Loosen cap (2). Carefully remove cap (2) from the housing of engine oil pump (1).
Note: The spring force will be released when the cap is removed.
4. Remove spring (4) from the bore for the relief valve in the housing of engine oil pump (1).
5. Use Tooling (A) to remove plunger (3) from the bore for the relief valve in the housing of
engine oil pump (1).
Installation Procedure
Table 2
2/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Required Tools
Tool Part Number Part Description Qty
B 4C-9506 Retaining Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01343561
Typical example
1. Ensure that all components are clean and free from wear or damage. If necessary, replace
any components that are worn or damaged. If the bore for the relief valve in the housing of
engine oil pump (1) is worn or damaged, the complete assembly of the engine oil pump
must be replaced.
3/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Lubricate plunger (3) with clean engine oil. Use long nose pliers to install plunger (3) and
spring (4) into the bore for the relief valve in the housing of engine oil pump (1).
Note: The plunger must slide freely in the bore for the relief valve.
3. Apply Tooling (A) to the threads of cap (2). Install cap (2) to engine oil pump (1). Tighten
the cap to a torque of 35 N·m (26 lb ft).
Note: Ensure that the spring is properly located inside the plunger and the cap. Ensure that
Tooling (A) does not contaminate the bore for the relief valve in the housing of engine oil
pump.
4. Install suction pipe (7) and a new joint (5) to the assembly of the engine oil pump.
5. Install bolts (6). Tighten the bolts to a torque to 22 N·m (16 lb ft).
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:51:44 UTC+0800 2019
4/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763420
Engine Oil Pump - Remove and Install - Engines Without a
Balancer Unit
SMCS - 1304-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Note: This procedure is for the removal of the engine oil pump on engines that are not equipped
with a balancer. Refer to Disassembly and Assembly, "Balancer Group - Remove" for information
on the removal of the engine oil pump for engines that are equipped with a balancer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/7434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g01343631
Typical example
1. Remove bolts (1) and suction pipe (2).
2. Remove the joint from suction pipe (2).
3. Remove bolts (5). Remove the assembly of engine oil pump (3) from the cylinder block.
4. If necessary, remove pressure relief valve (4) from the housing of engine oil pump (3).
Refer to Disassembly and Assembly, "Engine Oil Relief Vave - Remove and Install".
2/7434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01343633
Typical example
5. If necessary, remove bolts (9) and front cover assembly (6). Remove outer rotor (7) from
the housing of engine oil pump (3).
Note: Do not remove dowels (8) and (10) from the housing of the engine oil pump unless
the dowels are damaged.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7324 Indicator Bracket 1
3/7434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
Note: This procedure is for the installation of the engine oil pump on engines that are not
equipped with a balancer. Refer to Disassembly and Assembly, "Balancer Group - Install" for
information on the installation of the engine oil pump for engines that are equipped with a
balancer.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
If any of the parts on the engine oil pump are worn or damaged, the
entire pump must be replaced.
1. Ensure that all components of the engine oil pump are clean and free from wear or damage.
Check the clearance between the outer rotor of the oil pump and the oil pump body. Check
the clearance between the outer rotor and the inner rotor. Check the end play of the rotor.
Refer to the Systems Operation,Testing and Adjusting, "Engine Oil Pump - Inspect".
Replace the complete assembly of the engine oil pump if any of the components are worn or
damaged.
4/7434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g01343633
2. If necessary, lubricate the internal components of the assembly of the engine oil pump with
clean engine oil. Install outer rotor (7) and front cover (6) to the housing of engine oil pump
(3). Install bolts (9). Tighten the bolts to a torque of 9.5 N·m (84 lb in).
5/7434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g01343631
3. If necessary, install pressure relief valve (4). Refer to Disassembly and Assembly, "Engine
Oil Relief Valve - Remove and Install" for further information.
4. Ensure that dowels (8) and (10) are correctly located in the housing of engine oil pump (3).
Position the assembly of the engine oil pump onto the cylinder block.
Note: Ensure that the dowels in the housing of the engine oil pump are aligned with the
holes in the cylinder block.
5. Install bolts (5). Tighten the bolts to a torque of 44 N·m (32 lb ft).
6. Install suction pipe (2) and a new joint to the assembly of the engine oil pump.
7. Install bolts (1). Tighten the bolts to a torque to 22 N·m (16 lb ft).
8. Use Tooling (A) in order to check the backlash between the idler gear of the oil pump and
the crankshaft gear. Refer to Specifications, "Gear Group - Front" for further information.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Tue Sep 10 15:52:31 UTC+0800 2019
6/7434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763422
Water Pump - Remove
SMCS - 1361-011
Removal Procedure
Start By:
a. Remove the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1/3434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
correct procedure.
2. Loosen the hose clamps and remove the hose from the water pump inlet.
Illustration 1 g01263054
Typical example
3. Remove bolts (4). The bolts are different lengths. Note the positions of the different bolts.
Note: Do not remove bolts (7) at this time.
4. Remove water pump (3) from front cover (1).
Note: If necessary, tap the water pump with a soft hammer in order to loosen the water
pump.
2/3434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 5. Remove joint (2).
6. If necessary, remove cover (6) from the water pump. Follow Steps 6.a through 6.c in order
to remove the cover.
a. Remove bolts (7).
b. Remove cover (6).
c. Remove joint (5).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:53:19 UTC+0800 2019
3/3434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763423
Water Pump - Install
SMCS - 1361-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Bolt
(M8 by 80 mm)
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the water pump is clean and free from wear or damage. If necessary, replace the
water pump.
1/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 1 g01269391
Typical example
2. If necessary, install cover (6) to water pump (3). Follow Steps 2.a through 2.d in order to
install the cover.
a. Clean the mating surface of cover (6).
b. Position a new joint (5) onto water pump (3).
c. Install cover (6) to water pump (3).
d. Install bolts (7) to cover (6). Tighten the bolts finger tight.
3. Clean the mating surface of front cover (1).
2/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 2 g01269392
4. Install Tooling (A) in position (X).
5. Use Tooling (A) in order to align a new joint (2) to front cover (1). Install the joint to the
front cover.
6. Align water pump (3) with Tooling (A). Install the water pump to front cover (1).
Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
7. Install bolts (4). Refer to Illustration 1. Tighten the bolts finger tight.
Note: Ensure that bolts of different lengths are installed in the correct positions.
8. Remove Tooling (A) and install remaining bolts (4) finger tight.
3/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 3 g01269393
Tightening sequence for the water pump
9. Tighten bolts (4) and bolts (7) to a torque of 22 N·m (16 lb ft). Refer to Illustration 1.
Tighten the bolts in the sequence that is shown in Illustration 3.
10. Install the hose to the water pump inlet. Tighten the hose clamps.
11. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling
System Coolant - Change" for the correct procedure.
End By:
a. Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 15:54:07 UTC+0800 2019
4/4434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 434E BACKHOE LOADER SEF
Configuration: 434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 (Mech) Engines for Caterpillar Built Machines
Media Number -KENR9210-10 Publication Date -01/12/2014 Date Updated -08/08/2018
i02763424
Water Temperature Regulator - Remove and Install
SMCS - 1355-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system to a level below the water temperature regulator,
into a suitable container for storage or for disposal. Refer to Operation and Maintenance
Manual, "Cooling System Coolant - Change" for the correct draining procedure.
2. Loosen the hose clamps from the upper radiator hose and disconnect the upper radiator hose
from water temperature regulator housing (2).
1/5434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 1 g01343959
Typical example
3. Remove bolts (1) from water temperature regulator housing (2).
4. Remove water temperature regulator housing (2) from the cylinder head.
Note: Note the orientation of the water temperature regulator housing.
2/5434E Backhoe Loader SEF00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/9/10https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...