This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fjjskekfsem
This document provides instructions for removing and installing a flywheel housing on a 428C Backhoe Loader with a 3054 engine. It describes the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel, then removing bolts to take off the housing. For installation, the document specifies cleaning parts, installing seals and gaskets, and tightening bolts to the specified torques to attach the housing.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfdjdjfkjksk
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fjsjefskekfmme
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fjjskkdmnsme
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfjjsjekkmsmd
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, and reinstall the housing and gasket with bolts.
3) For engines with a 10 bolt housing, install the preassembled housing over the crankshaft until it contacts the cylinder block and centers it with a tool.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjufksefmme
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fjjskekfsem
This document provides instructions for removing and installing a flywheel housing on a 428C Backhoe Loader with a 3054 engine. It describes the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel, then removing bolts to take off the housing. For installation, the document specifies cleaning parts, installing seals and gaskets, and tightening bolts to the specified torques to attach the housing.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfdjdjfkjksk
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fjsjefskekfmme
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...fjjskkdmnsme
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn0...ujfjjsjekkmsmd
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, and reinstall the housing and gasket with bolts.
3) For engines with a 10 bolt housing, install the preassembled housing over the crankshaft until it contacts the cylinder block and centers it with a tool.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjufksefmme
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document is a service repair manual that provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and begins by having the transmission removed and installed on an engine stand. It then provides step-by-step instructions to disassemble the various transmission components including removing gears, shafts, seals, and other parts. Detailed illustrations accompany each step.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 430E backhoe loader. It lists the required tools and presents the steps in detail with illustrations. The removal procedure involves removing bolts and lowering the guard with a hydraulic jack to access the drive shaft. Installation is the reverse of removal.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housing in their proper order and orientation. Tolerances for shaft play are also specified to be checked with gauges during assembly. The transmission is then mounted to the vehicle and electrical and hydraulic connections are made.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, seals and housing in their proper order and orientation. Tools required for the assembly are listed. Precautions like applying transmission oil and heating bearings to the specified temperature before installation are mentioned. Final steps include installing the transmission in the vehicle and connecting related components.
The document provides instructions for disassembling the transmission of a 420F2 backhoe loader. It describes removing over 20 components from the transmission, including the torque converter, gears, shafts, bearings, seals and other parts. Safety warnings are included to release springs carefully and wear protective equipment. Detailed illustrations accompany each step. The goal is to fully disassemble the transmission down to its individual parts for repair or replacement.
The document provides instructions for assembling a 424D backhoe loader transmission. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housings. It also provides details on final assembly steps, which include applying sealant, installing the transmission case and shafts, and connecting electrical connectors. Tolerances for shaft play are specified to be checked with a dial indicator during assembly.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 422E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard while removing bolts and lowering the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening bolts to the specified torque.
4) Raising and securing the drive shaft guard with new bolts after installation is complete.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, replacing mounting hardware, refilling fluids, and reinstalling removed components. The document is a service repair manual that details the process to remove and install an engine on the specified backhoe loader model.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, connect related components like the transmission, alternator, and air conditioning, and refill fluids before completing reassembly. Tools including a hydraulic jack and load leveling beam are required. Proper installation ensures the engine operates safely and efficiently.
The document provides instructions for removing and installing the flywheel housing on a 422E Backhoe Loader. To remove the housing, the flywheel must first be removed. Bolts are then removed from the housing and it is lifted off using a device. When installing, dowels and seals are inspected, bolts are used to secure the housing, and torque specifications are provided. The process is intended to provide maintenance for the flywheel housing component.
This document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a Caterpillar 420F2 backhoe loader with a C4.4 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe how to remove the existing crankshaft rear seal and flywheel housing, clean and inspect components, install a new seal and gasket, and reinstall the housing while torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the transmission, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
The document provides instructions for disassembling the transmission of a 416E Backhoe Loader. It lists required tools and gives step-by-step instructions with illustrations. Key steps include removing the transmission from the vehicle, then disassembling its major components such as pumps, shafts, gears, seals and housing. Specific instructions are provided for disassembling the front and rear output shafts. Safety precautions are noted for releasing spring forces. The goal is to fully disassemble the transmission into its core components.
1. The document provides instructions for removing and installing various engine components on a Caterpillar 416F2 backhoe loader, including lifters, camshafts, camshaft bearings, and piston cooling jets.
2. The procedures describe using specialized tools to remove parts and ensuring parts are clean before installation.
3. Technicians are advised to mark lifters during removal for correct installation and lubricate parts with oil before reinstallation.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document is a service repair manual that provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and begins by having the transmission removed and installed on an engine stand. It then provides step-by-step instructions to disassemble the various transmission components including removing gears, shafts, seals, and other parts. Detailed illustrations accompany each step.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 430E backhoe loader. It lists the required tools and presents the steps in detail with illustrations. The removal procedure involves removing bolts and lowering the guard with a hydraulic jack to access the drive shaft. Installation is the reverse of removal.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housing in their proper order and orientation. Tolerances for shaft play are also specified to be checked with gauges during assembly. The transmission is then mounted to the vehicle and electrical and hydraulic connections are made.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, seals and housing in their proper order and orientation. Tools required for the assembly are listed. Precautions like applying transmission oil and heating bearings to the specified temperature before installation are mentioned. Final steps include installing the transmission in the vehicle and connecting related components.
The document provides instructions for disassembling the transmission of a 420F2 backhoe loader. It describes removing over 20 components from the transmission, including the torque converter, gears, shafts, bearings, seals and other parts. Safety warnings are included to release springs carefully and wear protective equipment. Detailed illustrations accompany each step. The goal is to fully disassemble the transmission down to its individual parts for repair or replacement.
The document provides instructions for assembling a 424D backhoe loader transmission. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housings. It also provides details on final assembly steps, which include applying sealant, installing the transmission case and shafts, and connecting electrical connectors. Tolerances for shaft play are specified to be checked with a dial indicator during assembly.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 422E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard while removing bolts and lowering the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening bolts to the specified torque.
4) Raising and securing the drive shaft guard with new bolts after installation is complete.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, replacing mounting hardware, refilling fluids, and reinstalling removed components. The document is a service repair manual that details the process to remove and install an engine on the specified backhoe loader model.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, connect related components like the transmission, alternator, and air conditioning, and refill fluids before completing reassembly. Tools including a hydraulic jack and load leveling beam are required. Proper installation ensures the engine operates safely and efficiently.
The document provides instructions for removing and installing the flywheel housing on a 422E Backhoe Loader. To remove the housing, the flywheel must first be removed. Bolts are then removed from the housing and it is lifted off using a device. When installing, dowels and seals are inspected, bolts are used to secure the housing, and torque specifications are provided. The process is intended to provide maintenance for the flywheel housing component.
This document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a Caterpillar 420F2 backhoe loader with a C4.4 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe how to remove the existing crankshaft rear seal and flywheel housing, clean and inspect components, install a new seal and gasket, and reinstall the housing while torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the transmission, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
The document provides instructions for disassembling the transmission of a 416E Backhoe Loader. It lists required tools and gives step-by-step instructions with illustrations. Key steps include removing the transmission from the vehicle, then disassembling its major components such as pumps, shafts, gears, seals and housing. Specific instructions are provided for disassembling the front and rear output shafts. Safety precautions are noted for releasing spring forces. The goal is to fully disassemble the transmission into its core components.
1. The document provides instructions for removing and installing various engine components on a Caterpillar 416F2 backhoe loader, including lifters, camshafts, camshaft bearings, and piston cooling jets.
2. The procedures describe using specialized tools to remove parts and ensuring parts are clean before installation.
3. Technicians are advised to mark lifters during removal for correct installation and lubricate parts with oil before reinstallation.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:01:26 UTC+0800 2019
2/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:02:23 UTC+0800 2019
3/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:03:19 UTC+0800 2019
4/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:04:16 UTC+0800 2019
4/4
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:05:13 UTC+0800 2019
2/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742537
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00541748
Typical example
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Place Tooling (B) in the holes in order to remove crankshaft front seal (1). Use Tooling (B)
in each of the three holes to evenly remove the crankshaft front seal.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:06:09 UTC+0800 2019
2/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742545
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the housing for the crankshaft front seal and inspect the housing for damage.
2. Lubricate the lip of the crankshaft front seal with clean engine oil.
1/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00541748
3. Place crankshaft front oil seal (1) into the housing.
NOTICE
Ensure that the lip of the crankshaft front seal that is spring loaded is
facing toward the inside of the front housing and that it is square with
the bore of the housing for the crankshaft front seal.
Illustration 2 g00622033
4. Use Tooling (A) to install crankshaft front oil seal (1).
5. Apply clean engine oil on the area of the crankshaft pulley that will be in contact with
crankshaft front seal (1).
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Mon Oct 14 18:07:06 UTC+0800 2019
2/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02108315
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
B. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
C. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Illustration 1 g00640000
1. Remove bolts (1) and nuts (3) from the front cover.
2. Remove front cover (2) and the gasket from the cylinder block.
Mon Oct 14 18:08:03 UTC+0800 2019
1/2
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01694904
Front Cover - Install
SMCS - 1166-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
B 4C-5501 Front Cover Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all surfaces of the front housing and clean the front cover thoroughly.
2. If necessary, use Tool (A) to install the crankshaft front oil seal. Refer to Disassembly and
Assembly, "Crankshaft Front Seal - Install".
1/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00640000
Illustration 2 g00546873
3. Install a new gasket and front cover (2) .
4. Install two bolts (1) in order to hold the gasket and the cover in place.
5. Use Tool (B) and the bolts for the crankshaft pulley in order to center the front cover.
NOTICE
The location of the front cover is critical. If the front cover is not
centered, the backlash between the fuel injection pump gear and the
water pump gear could be affected. This could result in damage to the
fuel injection pump.
6. Install the remaining bolts (1) and the two nuts (3). Tighten the nuts and the bolts to a torque
of 22 N·m (16 lb ft).
End By:
2/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
c. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:09:00 UTC+0800 2019
3/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02253357
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2264 Puller Group 1
B 173-9774 Wrench Bit 1
Start By:
A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...