This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block that holds the pulley in position. The installation procedure specifies cleaning parts and installing in the reverse order, tightening the bolts to the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, and reinstall the housing and gasket with bolts.
3) For engines with a 10 bolt housing, install the preassembled housing over the crankshaft until it contacts the cylinder block and centers it with a tool.
Caterpillar cat 426 c backhoe loader (prefix 1cr) service repair manual (1cr0...fjjsefkskemmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the component locations. The removal procedure describes using a lifting device and removing bolts to take off the flywheel. The installation procedure explains heating the flywheel ring gear, positioning the flywheel and installing bolts with the specified torque. It also provides separate instructions for engines with 14-bolt or 10-bolt housings when removing and installing the crankshaft rear seal.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fusjejfskekfmsme
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It lists the required tools and describes the steps, which include removing the V-belts, taking out the three bolts holding the pulley, and installing the pulley using the bolts. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting devices to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by pressing in the new seal, lubricating parts,
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fusjejedrfjskekem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts and washers, lifting the flywheel off, and installing in reverse order. For the crankshaft rear seal, it differentiates between engines using a 14 bolt or 10 bolt housing assembly and outlines cleaning, pressing or placing the seal, and torquing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, and reinstall the housing and gasket with bolts.
3) For engines with a 10 bolt housing, install the preassembled housing over the crankshaft until it contacts the cylinder block and centers it with a tool.
Caterpillar cat 426 c backhoe loader (prefix 1cr) service repair manual (1cr0...fjjsefkskemmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes a list of required tools and illustrations showing the component locations. The removal procedure describes using a lifting device and removing bolts to take off the flywheel. The installation procedure explains heating the flywheel ring gear, positioning the flywheel and installing bolts with the specified torque. It also provides separate instructions for engines with 14-bolt or 10-bolt housings when removing and installing the crankshaft rear seal.
Caterpillar cat 436 c backhoe loader (prefix 1pr) service repair manual (1pr0...fusjejfskekfmsme
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It lists the required tools and describes the steps, which include removing the V-belts, taking out the three bolts holding the pulley, and installing the pulley using the bolts. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting devices to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by pressing in the new seal, lubricating parts,
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 b backhoe loader (prefix 8sg) service repair manual (8sg0...fusjejedrfjskekem
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts and washers, lifting the flywheel off, and installing in reverse order. For the crankshaft rear seal, it differentiates between engines using a 14 bolt or 10 bolt housing assembly and outlines cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts to take off the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjufksefmme
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjsefkskemmm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fujjsekskemme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels using lifting brackets, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts.
3) Remove the crankshaft rear seal by removing housing bolts and housing.
4) Install the crankshaft rear seal by cleaning parts, installing the seal with a press
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fsejfjskefsmem
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and tightening bolts.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal with a
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fjksekkmsemm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels using lifting brackets, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjjkskekfsmem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Toyota bt spe140 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a forklift truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides procedures for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair and replacement instructions.
Toyota bt spe120 l electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
More Related Content
Similar to Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn04990 and up)
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing the crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts to take off the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It begins by listing the required tools. The removal procedure involves removing the V-belts, then removing three bolts and the thrust block. The installation procedure cleans surfaces, applies threadlocker to bolts, positions the thrust block and pulley, and tightens the bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjufksefmme
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjskekksemmrt
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes:
1) Removing mounting bolts from the top and sides of the flywheel housing and using lifting tools to remove the housing, which weighs approximately 70 lbs.
2) Cleaning the mating surfaces of the cylinder block and flywheel housing before installation. The instructions specify installing the housing by aligning it on the cylinder block and securing it with mounting bolts.
3) Recommendations to keep parts clean and contain fluids to prevent contamination or spills during the repair process.
Caterpillar cat 426 c backhoe loader (prefix 1er) service repair manual (1er0...fjjsefkskemmm
This document provides instructions for removing and installing a crankshaft rear seal on a 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel, housing, crankshaft rear seal, and gasket.
2) Clean and prepare the surfaces, install the new seal using a press, lubricate parts, and position the housing and gasket on dowels before installing bolts.
3) For 10 bolt housings, place the pre-lubricated seal on the crankshaft and use a centering tool to align the housing before installing bolts.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fujjsekskemme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels using lifting brackets, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes.
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fusjejfskekfmsme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts.
3) Remove the crankshaft rear seal by removing housing bolts and housing.
4) Install the crankshaft rear seal by cleaning parts, installing the seal with a press
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fsejfjskefsmem
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and tightening bolts.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal with a
Caterpillar cat 436 c backhoe loader (prefix 1rr) service repair manual (1rr0...fjksekkmsemm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels using lifting brackets, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjjkskekfsmem
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Similar to Caterpillar cat 428 c backhoe loader (prefix 8rn) service repair manual (8rn04990 and up) (20)
Toyota bt spe140 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a forklift truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides procedures for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair and replacement instructions.
Toyota bt spe120 l electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
Toyota bt spe120 electric stacker truck service repair manualfjjskkdmnsme
The document provides instructions for repairing and replacing various components on a truck chassis. It includes steps for replacing service covers, side covers, emblem covers, and other covers. It also provides instructions for checking and replacing components of the support arms and stabilizers, including the pressure rod, torsion tubes, and rollers on the torsion tubes. Diagrams are included to identify the relevant parts. The document is a repair manual containing detailed repair procedures.
Toyota bt reflex rre250 hecc high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt reflex rre250 hec high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
Toyota bt reflex rre250 he high performance reach truck service repair manualfjjskkdmnsme
The document is a repair manual that provides information on operating principles, safety, maintenance and troubleshooting for a series of forklift models. It includes sections on general introduction, safety rules, operating principle, installation, maintenance, troubleshooting, and technical specifications. The manual covers various systems of the forklifts such as chassis, motors, transmission, brakes, steering, electrical, hydraulics and optional equipment. It also contains wiring diagrams, hydraulic schematics and service data.
This document provides a parts list for Massey Ferguson 8450/8460 Tractors (Tier 3) engines and equipment. It includes 51 numbered items with descriptions of parts like engines, starters, belts, fans, clutches, shields, brackets, bolts, nuts, and labels. The parts apply to various engine serial number ranges for the MF 8450 and 8460 models. Footnotes provide additional details on some parts.
This document provides a parts list for Massey Ferguson 8450/8460 Tractors (Tier 3) engines and equipment. It includes 51 numbered items with descriptions of parts like engines, starters, belts, fans, shields, nuts, bolts and other components. Part numbers, quantities, serial number ranges and other identifying information is provided for each part.
Massey ferguson mf8280 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine of Massey Ferguson 8270/8280 tractors. It includes 25 items describing cylinder block parts, their part numbers, and quantities. It also includes information on the cylinder block equipment with 22 additional parts listed. Finally, it describes the timing gear housing with 11 parts. The document provides detailed technical specifications and part numbers for various engine components.
Massey ferguson mf8270 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine of Massey Ferguson 8270/8280 tractors. It includes 25 items describing cylinder block parts, their part numbers, and quantities. It also includes information on the cylinder block equipment with 22 additional parts listed. Finally, it describes the timing gear housing with 23 parts and specifications. Overall, the document is a parts catalog for the engine, listing over 100 individual part numbers and descriptions to repair or replace components.
Massey ferguson mf8240 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for a Massey Ferguson 8240 tractor engine. It includes detailed lists of parts with part numbers, descriptions, quantities and other identifying information. The parts are grouped into sections covering the cylinder block, timing gear housing, flywheel housing, crankshaft and other engine components. The document contains replacement part numbers where original parts are no longer available.
Massey ferguson mf8220 tractors parts catalogue manualfjjskkdmnsme
This document provides a list of parts and descriptions for the engine and components of Massey Ferguson 8210/8220 tractors. It includes 41 items describing the cylinder block, 25 items for the crankshaft, pistons, and connecting rods, 33 items for the cylinder head, 14 items for the rocker shaft, and 10 items for the lubricating oil filler and breather system. Each item includes the part number, quantity, description, and any relevant comments.
Massey ferguson mf8210 tractors parts catalogue manualfjjskkdmnsme
This document provides a list of parts and descriptions for the engine and components of Massey Ferguson 8210/8220 tractors. It includes 41 items describing the cylinder block, 25 items for the crankshaft, pistons, and connecting rods, 33 items for the cylinder head, 14 items for the rocker shaft, and 10 items for the lubricating oil filler and breather system. Each item includes the part number, quantity, description, and any relevant comments.
Massey ferguson mf8170 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the engine, alternator, starter, engine block heater, cylinder block, cylinder block equipment, timing gear housing, flywheel housing, crankshaft, pistons and connecting rods of a Massey Ferguson 8170 tractor with serial number 1637359. It contains lists of each component part number, quantity, description, and additional comments or specifications.
Massey ferguson mf8160 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for a Massey Ferguson 8160 tractor engine. It includes 3 pages listing 24 items that make up the cylinder block assembly, along with part numbers and descriptions. A second page lists 17 items that make up the cylinder head cover. The third page lists 26 items that make up the lubricating oil sump assembly.
Massey ferguson mf8150 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for an MF 8150 tractor engine. It includes 40 items describing engine parts like the cylinder block, pistons, crankshaft, timing gear housing, flywheel housing and other components. Each item lists the part number, quantity, description and any additional comments. It appears to be a parts catalog section for the engine of this tractor model.
Massey ferguson mf8140 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for an MF 8140 tractor engine. It includes a list of 39 engine parts with part numbers and quantities. The list includes major engine components like the cylinder block, crankshaft, pistons, connecting rods, timing gear housing, and flywheel housing. Footnotes provide additional details on some parts.
Massey ferguson mf8110 tractor parts catalogue manualfjjskkdmnsme
This document provides parts information for the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, and turbocharger of a Massey Ferguson 8110 tractor with a T6.60 engine and serial number 1637281. It includes item numbers, part numbers, quantities, descriptions, and comments for 42 total parts related to these engine components. Replacement and repair notes are included for some parts indicating whether old parts are interchangeable with new updated part numbers.
Massey ferguson mf7726 s tractor (dyna vt) (f026053 9999999) or (m7726efn9s10...fjjskkdmnsme
This document provides a table of contents and part listings for a Massey Ferguson 7726/7726S tractor. The table of contents lists 18 systems for the tractor, including the engine/fuel system, axles, steering, drivetrain, brakes, hydraulics, electrical, and others. Following this are pages with detailed parts lists and descriptions for components of the engine cylinder block, timing gears/housing, and other engine assemblies. Over 50 individual parts are detailed on these pages.
Kobelco sk027 hydraulic excavator service repair manual sn pw01700 and upfjjskkdmnsme
The document is a shop manual issued in April 1992 for the hydraulic excavators SK024, SK027, and SK032. It provides applicable part numbers and model information for repairs and maintenance. The manual was first edition printed in the United States and copyrighted by Kobelco Construction Machinery America, LLC.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:01:26 UTC+0800 2019
2/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:02:23 UTC+0800 2019
3/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:03:19 UTC+0800 2019
4/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:04:16 UTC+0800 2019
4/4428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:05:13 UTC+0800 2019
2/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742537
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00541748
Typical example
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Place Tooling (B) in the holes in order to remove crankshaft front seal (1). Use Tooling (B)
in each of the three holes to evenly remove the crankshaft front seal.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:06:09 UTC+0800 2019
2/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01742545
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the housing for the crankshaft front seal and inspect the housing for damage.
2. Lubricate the lip of the crankshaft front seal with clean engine oil.
1/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00541748
3. Place crankshaft front oil seal (1) into the housing.
NOTICE
Ensure that the lip of the crankshaft front seal that is spring loaded is
facing toward the inside of the front housing and that it is square with
the bore of the housing for the crankshaft front seal.
Illustration 2 g00622033
4. Use Tooling (A) to install crankshaft front oil seal (1).
5. Apply clean engine oil on the area of the crankshaft pulley that will be in contact with
crankshaft front seal (1).
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Mon Oct 14 18:07:06 UTC+0800 2019
2/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02108315
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
B. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
C. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Illustration 1 g00640000
1. Remove bolts (1) and nuts (3) from the front cover.
2. Remove front cover (2) and the gasket from the cylinder block.
Mon Oct 14 18:08:03 UTC+0800 2019
1/2428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01694904
Front Cover - Install
SMCS - 1166-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
B 4C-5501 Front Cover Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all surfaces of the front housing and clean the front cover thoroughly.
2. If necessary, use Tool (A) to install the crankshaft front oil seal. Refer to Disassembly and
Assembly, "Crankshaft Front Seal - Install".
1/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00640000
Illustration 2 g00546873
3. Install a new gasket and front cover (2) .
4. Install two bolts (1) in order to hold the gasket and the cover in place.
5. Use Tool (B) and the bolts for the crankshaft pulley in order to center the front cover.
NOTICE
The location of the front cover is critical. If the front cover is not
centered, the backlash between the fuel injection pump gear and the
water pump gear could be affected. This could result in damage to the
fuel injection pump.
6. Install the remaining bolts (1) and the two nuts (3). Tighten the nuts and the bolts to a torque
of 22 N·m (16 lb ft).
End By:
2/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
b. Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
c. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Oct 14 18:09:00 UTC+0800 2019
3/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 428C BACKHOE LOADER 8RN
Configuration: 428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02253357
Gear Group (Front) - Remove
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2264 Puller Group 1
B 173-9774 Wrench Bit 1
Start By:
A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3428C Backhoe Loader Side Shift, Single Tilt 8RN04990-UP (MACHINE) POWERED...
2019/10/14https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...