This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes:
1) Removing the flywheel by installing a lifting tool, removing bolts, and using lifting devices to remove the flywheel and flywheel ring gear.
2) Installing the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, installing bolts, and tightening them to the specified torque.
3) Removing the crankshaft rear seal by removing housing bolts and housing, and cleaning the sealing surfaces.
4) Installing the crankshaft rear seal by installing a new seal and
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel using a lifting device and by removing bolts; 2) Install the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, and tightening bolts; 3) Remove the crankshaft rear seal by removing housing bolts and separating the housing; 4) Install the crankshaft rear seal by pressing in the seal, lubricating surfaces, positioning the housing, and tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...jfksekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Installation instructions specify cleaning parts, placing the housing on the cylinder block, and tightening mounting bolts to secure the housing.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fujsjefjkskekfm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel using a lifting device and by removing bolts; 2) Install the flywheel by heating the flywheel ring gear, positioning the flywheel and ring gear, and tightening bolts; 3) Remove the crankshaft rear seal by removing housing bolts and separating the housing; 4) Install the crankshaft rear seal by pressing in the seal, lubricating surfaces, positioning the housing, and tightening bolts.
Caterpillar cat 426 c backhoe loader (prefix 6xn) service repair manual (6xn0...jfksekfmsme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing which include supporting the engine, removing mounting bolts, attaching lifting tools to the housing, and separating the housing from the cylinder block. Installation instructions specify cleaning parts, placing the housing on the cylinder block, and tightening mounting bolts to secure the housing.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It includes:
- Tools and parts needed for the job.
- Step-by-step instructions for removing the flywheel using a lifting device and removing bolts, then removing the crankshaft rear seal, gasket and housing.
- Instructions for installing the crankshaft rear seal using a press, lubricating the seal and crankshaft, and reinstalling the housing and bolts.
Caterpillar cat 426 c backhoe loader (prefix 1mr) service repair manual (1mr0...fujsjefjkskekfm
This document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing from the cylinder block.
4) Install the crankshaft
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and sides of the housing, and lifting the housing off using lifting brackets. The installation procedure specifies cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts to secure the housing. Tools required include lifting brackets and bolts of the appropriate sizes.
Caterpillar cat 416 c backhoe loader (prefix 1wr) service repair manual (1wr0...fujsjefksekmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 416 c backhoe loader (prefix 1xr) service repair manual (1xr0...fjsjejfksekmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools, and removing the housing. The installation procedure involves cleaning mating surfaces, positioning the housing on dowels in the cylinder block, and installing and tightening mounting bolts. Tools required include link brackets for lifting. Safety notices advise keeping parts clean and containing fluids.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjufksefmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include lifting brackets and torque wrenches. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing onto dowels in the cylinder block, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Toro reelmaster 5300 d mower service repair manualfusjejfjskekemm
This document is a service manual for the Reelmaster 5300-D that provides service technicians with information for troubleshooting, testing, and repairing major systems and components. It contains chapters covering safety instructions, product records and manuals, the Mitsubishi diesel engine, hydraulic system, electrical system, differentials, steering and brakes, cutting units, and the 4WD rear axle. Technicians are directed to follow all safety precautions when operating or servicing the machine.
Toro reelmaster 5100 d mower service repair manualfusjejfjskekemm
This document is a service manual for the Reelmaster 5100-D. It provides service technicians with information for troubleshooting, testing, and repairing major systems and components of the Reelmaster 5100-D. The manual contains chapters covering safety instructions, product records, the Mitsubishi diesel engine, hydraulic system, electrical system, differentials, steering and brakes, cutting units, and rear axle. It includes specifications, schematics, troubleshooting guides, testing procedures, and repair instructions for each system.
Toro groundsmaster 3000 service repair manualfusjejfjskekemm
This document is a service manual for the Groundsmaster 3000/3000-D. It contains chapters covering safety, product records and maintenance, engine specifications, hydraulic and electrical systems, rear axles, and cutting units. The manual provides service technicians with information for troubleshooting, testing, and repairing major systems and components. It emphasizes safety precautions that should be followed during operation and maintenance.
Toro greensmaster 3200 d service repair manualfusjejfjskekemm
This document is a service manual that provides information for troubleshooting, testing, and repairing major systems and components of the Greensmaster 3200/3200-D. It contains chapters covering safety, product records and maintenance, the Vanguard 3/LC gasoline engine, the Perkins engine, the hydraulic system, the electrical system, wheels and brakes, cutting units, and other systems. Technicians can use this manual to work on and repair parts of the Greensmaster.
Still wagner efv 160 forklift service repair manualfusjejfjskekemm
This document is a workshop manual for electric forklift trucks. It provides specifications and describes the functional characteristics and components of the trucks to allow for proper maintenance and repair. The manual is divided into sections covering various vehicle systems and components. Updates are provided through replacement or supplementary sheets as the truck models are further developed.
Still mx x order picker general 1, 2 80 v forklift service repair manualfusjejfjskekemm
The document provides a link to click for more information about an unspecified topic. It notes that if the link does not work, the reader should first download the attached PDF document and then click on the link contained within it to access the additional information.
The document contains technical specifications for a battery including battery type, capacity, voltage, software version, sensors, hardware version, and maintenance intervals. It lists parameters, sensor readings, and voltage levels for various components of the battery.
This document contains technical specifications for a battery including:
- Battery type, capacity, voltage, weight, and dimensions
- Software version information for various components like the charger, converter, and sensors
- Operating parameters such as lift/lower/tilt speeds and currents
- Diagnostic values for temperature, voltage, and current sensors
This document provides specifications and repair procedures for the STIHL MS 460 chainsaw from 2004-2011. It includes specifications on the engine, fuel system, ignition system, and other components. The document also provides detailed instructions for troubleshooting, disassembling, repairing, and reassembling the various systems and components of the chainsaw. Tightening torques are specified for fasteners. Special tools needed for repairs are referenced.
This document provides specifications and repair procedures for STIHL MS 290, 310, and 390 chainsaws from 2004-2011. It covers the engine, fuel system, ignition system, clutch, chain drive, rewind starter, handles, chain lubrication, and other systems. Troubleshooting charts list common problems, causes, and remedies. The document instructs technicians to use original STIHL replacement parts and observe all safety precautions when servicing the saws.
This document provides service and repair information for the STIHL MS 270 and MS 280 chainsaws. It includes specifications, troubleshooting charts, repair procedures, and torque specifications for various components. The document gives detailed instructions and diagrams for servicing the engine, clutch, chain drive, ignition system, fuel system, and other parts. Safety precautions for repair work involving the chainsaw and gasoline are also provided.
Stihl ms 200 t chainsaw service repair manualfusjejfjskekemm
This document provides specifications and service information for STIHL MS 200 and MS 200 T chainsaws. It includes sections on safety precautions, specifications, troubleshooting, repairs and replacement of parts, tools needed, and other technical details. Tightening torques are listed for various fasteners.
Stihl ms 192 t chainsaw service repair manualfusjejfjskekemm
This document provides specifications and troubleshooting information for the STIHL MS 192 T chainsaw. It includes specifications for the engine, fuel system, ignition system, and chain lubrication system. The document also lists typical tightening torques for various fasteners. Additionally, it provides potential causes and remedies for common problems with the clutch, chain drive, chain brake, chain tensioner, chain lubrication, rewind starter, ignition system, carburetor, and engine.
This document provides instructions for dismantling and assembling the safety equipment, specifically the chain brake, on several chain saw models. It describes removing parts like the clutch cover, guide bar, chain, hand guard, brake spring, toggle joint, and bearing pin. It emphasizes checking for wear on parts like the brake band which should be at least 0.8mm thick. Proper lubrication and handling of tensioned parts like the brake spring are also highlighted for safety.
More Related Content
Similar to Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr01517 02191)
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1zr) service repair manual (1zr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear if necessary.
2) Install the flywheel by heating and installing the flywheel ring gear if removed, installing the flywheel with a lifting tool, and replacing the bolts and tightening them to the specified torque.
3) Remove the crankshaft rear seal by removing housing bolts and housing, and removing the seal, gasket, and housing.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjufksefmme
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing on dowels in the cylinder block, and installing mounting bolts with the specified torque. Tools required include lifting brackets and torque wrenches. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. The installation procedure involves cleaning mating surfaces, placing the housing onto dowels in the cylinder block, and installing mounting bolts. Tools required include lifting brackets and bolts of various sizes. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjeskfksmefmm
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fusjejfjskekemm
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and lists the steps to:
1) Remove the flywheel by installing a lifting tool, removing bolts, and using lifting to remove the flywheel and flywheel ring gear.
2) Install the flywheel by heating the ring gear, installing it on the flywheel, positioning the flywheel and installing bolts while using lifting tools.
3) Remove the crankshaft rear seal by removing housing bolts and hardware.
4) Install the crankshaft rear seal by cleaning parts, installing the seal, lubricating, positioning
Caterpillar cat 426 c backhoe loader (prefix 1nr) service repair manual (1nr0...fjjskekksemmrt
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the flywheel, electric starting motor, and mounting bolts to lift the housing off the engine. For installation, it describes cleaning mating surfaces, checking the oil pan seal, and lowering the housing into place with alignment dowels before reinstalling the mounting bolts and other components.
Similar to Caterpillar cat 426 c backhoe loader (prefix 1yr) service repair manual (1yr01517 02191) (7)
Toro reelmaster 5300 d mower service repair manualfusjejfjskekemm
This document is a service manual for the Reelmaster 5300-D that provides service technicians with information for troubleshooting, testing, and repairing major systems and components. It contains chapters covering safety instructions, product records and manuals, the Mitsubishi diesel engine, hydraulic system, electrical system, differentials, steering and brakes, cutting units, and the 4WD rear axle. Technicians are directed to follow all safety precautions when operating or servicing the machine.
Toro reelmaster 5100 d mower service repair manualfusjejfjskekemm
This document is a service manual for the Reelmaster 5100-D. It provides service technicians with information for troubleshooting, testing, and repairing major systems and components of the Reelmaster 5100-D. The manual contains chapters covering safety instructions, product records, the Mitsubishi diesel engine, hydraulic system, electrical system, differentials, steering and brakes, cutting units, and rear axle. It includes specifications, schematics, troubleshooting guides, testing procedures, and repair instructions for each system.
Toro groundsmaster 3000 service repair manualfusjejfjskekemm
This document is a service manual for the Groundsmaster 3000/3000-D. It contains chapters covering safety, product records and maintenance, engine specifications, hydraulic and electrical systems, rear axles, and cutting units. The manual provides service technicians with information for troubleshooting, testing, and repairing major systems and components. It emphasizes safety precautions that should be followed during operation and maintenance.
Toro greensmaster 3200 d service repair manualfusjejfjskekemm
This document is a service manual that provides information for troubleshooting, testing, and repairing major systems and components of the Greensmaster 3200/3200-D. It contains chapters covering safety, product records and maintenance, the Vanguard 3/LC gasoline engine, the Perkins engine, the hydraulic system, the electrical system, wheels and brakes, cutting units, and other systems. Technicians can use this manual to work on and repair parts of the Greensmaster.
Still wagner efv 160 forklift service repair manualfusjejfjskekemm
This document is a workshop manual for electric forklift trucks. It provides specifications and describes the functional characteristics and components of the trucks to allow for proper maintenance and repair. The manual is divided into sections covering various vehicle systems and components. Updates are provided through replacement or supplementary sheets as the truck models are further developed.
Still mx x order picker general 1, 2 80 v forklift service repair manualfusjejfjskekemm
The document provides a link to click for more information about an unspecified topic. It notes that if the link does not work, the reader should first download the attached PDF document and then click on the link contained within it to access the additional information.
The document contains technical specifications for a battery including battery type, capacity, voltage, software version, sensors, hardware version, and maintenance intervals. It lists parameters, sensor readings, and voltage levels for various components of the battery.
This document contains technical specifications for a battery including:
- Battery type, capacity, voltage, weight, and dimensions
- Software version information for various components like the charger, converter, and sensors
- Operating parameters such as lift/lower/tilt speeds and currents
- Diagnostic values for temperature, voltage, and current sensors
This document provides specifications and repair procedures for the STIHL MS 460 chainsaw from 2004-2011. It includes specifications on the engine, fuel system, ignition system, and other components. The document also provides detailed instructions for troubleshooting, disassembling, repairing, and reassembling the various systems and components of the chainsaw. Tightening torques are specified for fasteners. Special tools needed for repairs are referenced.
This document provides specifications and repair procedures for STIHL MS 290, 310, and 390 chainsaws from 2004-2011. It covers the engine, fuel system, ignition system, clutch, chain drive, rewind starter, handles, chain lubrication, and other systems. Troubleshooting charts list common problems, causes, and remedies. The document instructs technicians to use original STIHL replacement parts and observe all safety precautions when servicing the saws.
This document provides service and repair information for the STIHL MS 270 and MS 280 chainsaws. It includes specifications, troubleshooting charts, repair procedures, and torque specifications for various components. The document gives detailed instructions and diagrams for servicing the engine, clutch, chain drive, ignition system, fuel system, and other parts. Safety precautions for repair work involving the chainsaw and gasoline are also provided.
Stihl ms 200 t chainsaw service repair manualfusjejfjskekemm
This document provides specifications and service information for STIHL MS 200 and MS 200 T chainsaws. It includes sections on safety precautions, specifications, troubleshooting, repairs and replacement of parts, tools needed, and other technical details. Tightening torques are listed for various fasteners.
Stihl ms 192 t chainsaw service repair manualfusjejfjskekemm
This document provides specifications and troubleshooting information for the STIHL MS 192 T chainsaw. It includes specifications for the engine, fuel system, ignition system, and chain lubrication system. The document also lists typical tightening torques for various fasteners. Additionally, it provides potential causes and remedies for common problems with the clutch, chain drive, chain brake, chain tensioner, chain lubrication, rewind starter, ignition system, carburetor, and engine.
This document provides instructions for dismantling and assembling the safety equipment, specifically the chain brake, on several chain saw models. It describes removing parts like the clutch cover, guide bar, chain, hand guard, brake spring, toggle joint, and bearing pin. It emphasizes checking for wear on parts like the brake band which should be at least 0.8mm thick. Proper lubrication and handling of tensioned parts like the brake spring are also highlighted for safety.
This document provides instructions for dismantling and assembling the safety equipment, specifically the chain brake, on several chain saw models. It describes removing parts like the clutch cover, guide bar, chain, hand guard, brake spring, toggle joint, and bearing pin. It emphasizes checking that the brake band has a minimum thickness of 0.8mm and lubricating moving parts during assembly. Safety warnings are included to avoid injury from the tensioned brake spring.
Jcb isuzu engine au 4 le2 bv-4le2 service repair manualfusjejfjskekemm
This document provides general information and service precautions for working on engines. It discusses recommended lubricants, a table of contents, reading the model number, terminology and abbreviations. Safety precautions are outlined, including using proper tools and protective equipment. Instructions are provided for removing and applying liquid gasket, using locking agents like Loctite, and measuring clearances with Plastigage. Standard torque specifications are included.
Jcb dieselmax engine (sa sc build) service repair manualfusjejfjskekemm
This document provides an overview and technical specifications for JCB Dieselmax mechanical engines. It includes:
- Identification of major engine components and labeling
- Engine data such as dimensions, capacities and specifications
- Information on acceptable and unacceptable fuels
- Lubrication requirements and coolant mixtures
- Torque specifications for fasteners
- Identification of service tools and repair kits
Jcb diesel 1100 series engine rf service repair manualfusjejfjskekemm
This document is a workshop manual for Perkins 1100 Series 4 cylinder diesel engines. It provides detailed instructions for disassembly, inspection, repair and reassembly of engine components. The manual is written for use by technicians and includes safety information, specifications, torque values and a parts list. Individual chapters cover the cylinder head, pistons, connecting rods, crankshaft, timing gears and other systems.
Jcb diesel 1000 series engine model as service repair manualfusjejfjskekemm
This document is a workshop manual for Perkins New 1000 Series diesel engines used in industrial and agricultural applications. It provides detailed instructions on servicing and repairing engine components like the cylinder head, pistons, crankshaft, timing case, cylinder block, and other systems. The manual contains chapters covering general information, specifications, disassembly and assembly procedures, inspection criteria, and specifications/dimensions for components. It is intended to guide mechanics in properly servicing and repairing these engines.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406238
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00546794
Typical Example. Different lifting device shown than what is called out in the Table.
Illustration 2 g00546793
1. Install Tool (A) and a suitable lifting device on flywheel (1) .
2. Remove bolts (3) and bearing housing (4) .
3. Remove six bolts (2) and the washers from the flywheel.
Note: The 3054 and 3056 marine engines used several bolt patterns to attach the flywheel to
the crankshaft. There are drilled holes that are not used in the crankshaft and in the
flywheel.
4. Use the suitable lifting device in order to remove flywheel (1) . The weight of flywheel (1)
and the flywheel ring gear is 53 kg (120 lb).
5. If removal of the flywheel ring gear is necessary, place an index mark on the chamfer of the
flywheel ring gear for the installation process.
Illustration 3 g00546795
2/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 6. Use a hammer and a punch in order to remove flywheel ring gear (5) from flywheel (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:24:34 UTC+0800 2019
3/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04406239
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
Always wear protective gloves when handling parts that have been
heated.
1/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00803517
Typical Example. Different Lifting device shown than what is called out in the table.
1. If flywheel ring gear (5) was removed, heat flywheel ring gear (5) to a temperature of 250 °
C (480 °F).
Note: Do not use a torch to heat the flywheel ring gear.
2. Install flywheel ring gear (5) on flywheel (1) .
Note: Ensure that the chamfer of the flywheel ring gear is in the correct position on the
flywheel.
3. Install Tool (A) and a suitable lifting device on flywheel (1) and position flywheel (1) in the
flywheel housing. The weight of flywheel (1) and flywheel ring gear (5) is 53 kg (120 lb).
Illustration 2 g00546793
4. Install six bolts (2) and the washers that hold flywheel (1) in position. Tighten the bolts to a
torque of 105 N·m (77 lb ft).
5. Put bearing housing (4) in position on the flywheel. Install four bolts (3) that fasten bearing
housing (4) to the flywheel.
6. Refer to the Specifications Module, "Flywheel" topic for information on inspecting the
flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:25:30 UTC+0800 2019
2/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741403
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Engines with 14 Bolt Housing Assembly
Illustration 1 g00632744
The flywheel housing has been removed for photographic purposes only.
1. Remove bolts (1) from housing (3).
2. Remove socket head bolts (2) from housing (3).
3. Remove the crankshaft rear seal, the gasket, and housing (3) from the dowels in the cylinder
block.
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
Illustration 2 g00830867
2/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Remove the bolts in reverse order of the numbered sequence. Refer to Illustration 2.
2. Remove the one-piece housing assembly from the cylinder block.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:26:26 UTC+0800 2019
3/3426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01605362
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6205 Rear Seal Installer 1
1P-0510 Driver Group 1
B FT-2806 Alignment Tool 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Engines with 14 Bolt Housing Assembly
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Clean the areas of the parts that will contact each other.
1/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00541839
3. Use Tool (A) and a suitable press to install the crankshaft rear seal into the housing. Make
sure that you install the seal to the correct depth in the housing. Refer to Specifications,
"Crankshaft Seals" for additional information.
4. Lubricate the crankshaft flange and the lip of the crankshaft rear seal with clean engine oil.
5. Install Tool (A) onto the crankshaft flange.
6. Put the new gasket for the housing in position on the dowels in the cylinder block.
Illustration 2 g00606404
7. Carefully place housing (3) and crankshaft rear seal (4) over Tool (A) .
8. Position housing (3) on the dowels in the cylinder block.
9. Remove Tool (A) .
2/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00606340
The flywheel housing has been removed for photographic purposes only.
10. Install bolts (1) and socket head bolts (2) that fasten housing (3) to the cylinder block.
11. Tighten all of the bolts to a torque of 22 N·m (16 lb ft).
Engines with 10 Bolt Housing Assembly
Note: The 10 bolt housing assembly is manufactured as a one-piece assembly. The 10 bolt
housing assembly is NOT adaptable to engines that have the 14 bolt housing assembly.
1. Ensure that all parts and surfaces of the engine block are clean and free from oil, grease, and
dirt.
Illustration 4 g00831176
3/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: The crankshaft rear seal is lubricated. There is no need to lubricate the seal or the
crankshaft flange before installation.
2. Place housing assembly (3) on crankshaft flange (1) until the housing assembly contacts the
cylinder block face. Plastic sleeve (2) will push out of the housing assembly. Discard the
plastic sleeve after the housing assembly is installed.
3. Place Tool (B) over housing assembly (3). This will center the housing assembly onto the
crankshaft flange.
Illustration 5 g00830867
4. Install the bolts with Tool (B) in position in order to fasten housing assembly (3) to the
cylinder block. Tighten bolts 1 and 2 to a torque of 22 N·m (16 lb ft).
5. Remove Tool (B). Tighten the remaining bolts in sequence to a torque of 22 N·m (16 lb ft).
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:27:22 UTC+0800 2019
4/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01741450
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Support the engine with blocks or with a suitable lifting device on a flat level surface.
Illustration 1 g00541891
Typical example
2. Remove mounting bolts (1) from the top of flywheel housing (2).
Illustration 2 g00541892
Typical example
3. Attach Tooling (A) and a suitable lifting device to flywheel housing (2).
4. Remove mounting bolts (3) that attach the flywheel housing to the cylinder block.
2/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. 5. Remove flywheel housing (2). If necessary, hit flywheel housing (2) with a soft faced
hammer in order to separate flywheel housing (2) from the cylinder block. The weight of
flywheel housing (2) is approximately 32 kg (70 lb).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the rear face of the cylinder block and the mating surface of the flywheel housing.
Inspect the felt seal on the rear flange of the engine oil pan. Replace the felt seal, if
necessary. Inspect the dowels in the cylinder block that align the flywheel housing. Replace
the dowels, if necessary.
Illustration 3 g00541892
2. Use Tooling (A) and a suitable lifting device to position flywheel housing (2) on the dowels
that are on the cylinder block. The weight of flywheel housing (2) is approximately 32 kg
(70 lb).
3. Install mounting bolts (3).
3/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g00541891
Typical example
4. Install mounting bolts (1) that attach flywheel housing (2) to the cylinder block.
Tighten the bolts for an aluminum flywheel housing to a torque of 70 N·m (52 lb ft).
Tighten the cast iron flywheel housing bolts to the following torque:
M10 "8.8" ... 44 N·m (33 lb ft)
M10 "10.9" ... 63 N·m (46 lb ft)
M12 "8.8" ... 75 N·m (55 lb ft)
M12 "10.9" ... 115 N·m (85 lb ft)
5. Remove Tooling (A) from the flywheel housing.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:28:17 UTC+0800 2019
4/4426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 426C BACKHOE LOADER 1YR
Configuration: 426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01461242
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Start By:
A. Remove the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Illustration 1 g00553762
Typical example
1. Remove three bolts (2) that hold thrust block (3) in position.
2. Remove thrust block (3) from the end of the crankshaft. The thrust block holds the
crankshaft pulley in position on the end of the crankshaft.
3. Remove crankshaft pulley (1) from the engine.
1/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: Some engines have a water immersion seal that is placed on the front cover. The seal has a
flexible lip on the front. The plastic mandrel that is supplied with the seal must be installed in the
seal when the crankshaft pulley is removed. This will ensure that the lip maintains the correct
shape.
Installation Procedure
Illustration 2 g00553762
Typical example
1. Remove the plastic mandrel, if necessary.
2. Put crankshaft pulley (1) in position on the crankshaft.
3. Apply 9S-3263 Thread Lock Compound to the threads of three bolts (2) .
4. Put thrust block (3) in position and align the holes with the holes in the end of the
crankshaft.
Note: It may be necessary to keep the crankshaft from rotating while you torque bolts (3).
Use the appropriate tools in order to keep the crankshaft from rotating.
5. Install three bolts (2) that hold the thrust block in position. Tighten bolts (2) to a torque of
115 N·m (85 lb ft).
End By: Install the V-Belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Dec 13 19:29:13 UTC+0800 2019
2/2426C Backhoe Loader Center Pivot, Parallel Lift 1YR01517-02191 (MACHINE) PO...
2019/12/13https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...