The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the machine
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of the removal steps.
Caterpillar cat 420 f backhoe loader (prefix jwj) service repair manual (jwj0...fujskeksmemqa
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. It describes how to disassemble 17 parts of the pump including springs, seals, bearings, and housings. It then describes how to assemble 19 parts in reverse order while precisely setting bearing preloads. A separate section provides instructions for removing and installing the hydraulic tank, which involves disconnecting hoses and brackets before removing the tank assembly.
Caterpillar cat 420 f backhoe loader (prefix jwj) service repair manual (jwj0...fjsjekkdmme
This document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The steps include:
1. Disconnecting hoses and clamps from the hydraulic tank.
2. Removing bolts to detach the tank from the vehicle.
3. Removing additional components like a strainer and gauge from the tank.
4. Reversing the process to install the new or repaired tank.
Caterpillar cat 420 f backhoe loader (prefix jwj) service repair manual (jwj0...ufujjdjkskemme
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F backhoe loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely and prevent injury.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. It describes:
1) Disconnecting hoses and clamps from the hydraulic tank assembly.
2) Removing bolts to detach the tank from the machine frame.
3) Reversing the removal steps to install the new or repaired tank.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. It describes:
1) Disconnecting hoses and clamps from the hydraulic tank assembly.
2) Removing bolts to detach the tank from the machine frame.
3) Reversing the removal steps to install the new or repaired tank.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. It describes:
1) Disconnecting hoses and clamps from the hydraulic tank assembly.
2) Removing bolts securing the tank mounts and lifting the tank from the machine.
3) Reversing the removal steps to install the new or repaired tank.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
Caterpillar cat 420 f backhoe loader (prefix jwj) service repair manual (jwj0...fujskeksmemqa
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. It describes how to disassemble 17 parts of the pump including springs, seals, bearings, and housings. It then describes how to assemble 19 parts in reverse order while precisely setting bearing preloads. A separate section provides instructions for removing and installing the hydraulic tank, which involves disconnecting hoses and brackets before removing the tank assembly.
Caterpillar cat 420 f backhoe loader (prefix jwj) service repair manual (jwj0...fjsjekkdmme
This document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The steps include:
1. Disconnecting hoses and clamps from the hydraulic tank.
2. Removing bolts to detach the tank from the vehicle.
3. Removing additional components like a strainer and gauge from the tank.
4. Reversing the process to install the new or repaired tank.
Caterpillar cat 420 f backhoe loader (prefix jwj) service repair manual (jwj0...ufujjdjkskemme
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F backhoe loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely and prevent injury.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. It describes:
1) Disconnecting hoses and clamps from the hydraulic tank assembly.
2) Removing bolts to detach the tank from the machine frame.
3) Reversing the removal steps to install the new or repaired tank.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. It describes:
1) Disconnecting hoses and clamps from the hydraulic tank assembly.
2) Removing bolts to detach the tank from the machine frame.
3) Reversing the removal steps to install the new or repaired tank.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. It describes:
1) Disconnecting hoses and clamps from the hydraulic tank assembly.
2) Removing bolts securing the tank mounts and lifting the tank from the machine.
3) Reversing the removal steps to install the new or repaired tank.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely when handling spring-loaded components during disassembly and assembly.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely when handling spring-loaded components.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely when handling spring-loaded components.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure and prevent injury when handling spring-loaded components.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to lift off the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety warnings are provided to relieve spring pressure before removing or installing spring-loaded components.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
More Related Content
Similar to Caterpillar Cat 420F Backhoe Loader (Prefix JWJ) Service Repair Manual (JWJ00001 and up).pdf
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely when handling spring-loaded components during disassembly and assembly.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely when handling spring-loaded components.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure safely when handling spring-loaded components.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided to relieve spring pressure and prevent injury when handling spring-loaded components.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses from the tank, removing clamps, and taking out bolts to lift off the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety warnings are provided to relieve spring pressure before removing or installing spring-loaded components.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F Backhoe Loader. The removal procedure involves disconnecting hoses and clamps connecting the tank to other components, and removing bolts to detach the tank assembly. Components like a strainer and gauge are also removed from the tank. The installation procedure is the reverse of removal.
This document provides instructions for removing and installing a hydraulic tank on a 430F backhoe loader. The steps include disconnecting hoses and clamps from the tank, removing bolts to detach the tank from the machine, and removing additional components like a strainer and gauge from the tank. The assembly process involves installing these components in reverse order.
Similar to Caterpillar Cat 420F Backhoe Loader (Prefix JWJ) Service Repair Manual (JWJ00001 and up).pdf (17)
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F BACKHOE LOADER JWJ
Configuration: 420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416F, 420F and 430F Backhoe Loaders Machine Systems
Media Number -UENR2321-04 Publication Date -01/01/2014 Date Updated -03/11/2016
i06851396
Piston Pump - Disassemble - Main Hydraulic
SMCS - 5070-015; 5455
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
437-3776 Fixture As. 1
1U-9128 Adapter Plate 1
1U-5750 Engine Stand 1
B 9S-9152 Bearing Puller 1
Start By:
a. Remove the piston pump (main hydraulic).
1/6
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06141568
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
1. Secure the piston pump to Tooling (A) or a suitable fixture.
2. Remove nut (2) and the O-ring seal, solenoid (3), and valve (4) from main pump housing
(6).
3. Remove bolts (5) and compensator valve (1) from main pump housing (6).
Illustration 2 g06141600
4. Remove actuator piston (7), spring guide (8), spring (9), spool (10), and O-ring seals (11)
from valve (4).
Illustration 3 g06141787
2/6
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
5. Remove gasket (12) from compensator valve (1).
6. Remove plug (18), O-ring seal (17), spring (16), spring (15), guide (14), and spool (13)
from compensator valve (1).
7. Remove plug (24), O-ring seal (23), spring (22), spring (21), guide (20), and spool (19)
from compensator valve (1).
Illustration 4 g06141800
Sudden release of spring force can cause injury.
To prevent the possibility of injury, follow the procedure to relieve the
spring pressure.
8. Remove cover (27) and the O-ring seal. Remove adjustment screw (28) and the O-ring seal.
Remove bolts (25) and head assembly (26).
3/6
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g06141813
9. Remove O-ring seal (29) and port plate (31) from head assembly (26).
10. Remove bearing cup (30) from head assembly (26).
Illustration 6 g06141820
Illustration 7 g06142001
11. Remove bearing cone (31), O-ring seals (32), and shim (33) .
12. Use Tooling (A) to rotate main pump housing (6) to a horizontal position. Remove rotary
group (34).
4/6
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g06141940
13. Remove swashplate (35) from main pump housing (6).
Illustration 9 g06141943
14. Remove shaft assembly (36) and spring (37).
Illustration 10 g06141945
15. Use Tooling (B) and a suitable press to remove bearing cone (38) from shaft assembly (36).
5/6
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g06141984
16. Remove screws (39) and bearings (40). Remove bearing cup (41).
Illustration 12 g06141995
17. Remove retaining ring (42) and shaft seal (43) from main pump housing (6).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 22:55:40 UTC+0800 2019
6/6
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F BACKHOE LOADER JWJ
Configuration: 420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416F, 420F and 430F Backhoe Loaders Machine Systems
Media Number -UENR2321-04 Publication Date -01/01/2014 Date Updated -03/11/2016
i06851397
Piston Pump - Assemble - Main Hydraulic
SMCS - 5070-016; 5455
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
437-3776 Fixture As. 1
1U-9128 Adapter Plate 1
1U-5750 Engine Stand 1
C 8H-8581 Feeler Gauge 1
D 8T-5096 Indicator 1
E
1B-9575 Bolt 1
5S-0003 Nut 1
F 6V-2055 Grease 1
1/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g06141995
1. Install shaft seal (43) and retaining ring (42) into main drive pump housing (6).
Illustration 2 g06141984
2. Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup
(41). Install bearing cup (41).
3. Install bearings (40) and screws (39). Tighten screws (40) to a torque of 5 ± 1 N·m
(44 ± 8 lb in).
Illustration 3 g06142051
2/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 4. Use the proper equipment to handle bearing cone (38). Raise the temperature of bearing
cone (38) to a maximum of 121 °C (250 °F). Install bearing cone (38) onto the shaft
assembly (36).
Illustration 4 g06141943
5. Install shaft assembly (36) and spring (37).
6. Use the following steps to determine the proper preload on the bearings of the pump
assembly.
Illustration 5 g06143192
a. Use the proper equipment to handle the bearing cup. Lower the temperature of
bearing cup (30) and install the bearing cup in head assembly (26).
3/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 6 g06143201
b. Install bearing cone (31) onto shaft assembly (36).
Assemble the pump without shim (10) in order to check the preload of bearing cone
(7).
Illustration 7 g06143218
c. Position the head assembly onto the main drive pump housing. Install bolts
(25).Tighten bolts (25) to a torque of 205 ± 10 N·m (151 ± 7 lb ft).
Illustration 8 g06143597
d. Set bearing preload before you install the rotating group. The bearing preload should
be 0.00 to 0.05 mm (0.000 to 0.002 inch) .
e. Install Tooling (E) into shaft assembly (36). Install Tooling (D) onto the pump
housing. Use Tooling (D) to determine the end play of shaft (36). Be sure that you
move shaft (36) completely in both directions. Use appropriate tools to move shaft
(36).
f. If necessary, grind the adjustment shim to obtain the correct dimension between the
head assembly and the main drive pump housing. If necessary, replace the shim with
a new part.
4/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. g. The thickness of the shim should equal the end play measurement plus 0.0508 mm
(0.00200 inch). For example, if the end play is 2.1590 mm (0.08500 inch) then the
shim thickness should be 2.2098 mm (0.08700 inch).
h. Record the measurement.
i. If necessary, grind the shim to the determined measurement.
j. Remove the head assembly from the main drive pump housing. Remove the bearing
cone and the adjustment shim from the shaft assembly.
k. Proceed with the assembly of the main hydraulic pump.
Illustration 9 g06143452
Illustration 10 g06141940
Note: It is necessary to compress spring (37) through hole in pump housing (6) to install
swashplate (35).Ensure that spring (37) is installed correctly onto swashplate (35) before
continuing the assembly.
7. Install swashplate (35) into main drive pump housing (6).
5/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 11 g06143325
Illustration 12 g06141820
8. Install rotary group (34), shim (33) that was determined in Step 6, and O-ring seals (32).
9. Install bearing cone (31) into main pump housing (6).
Illustration 13 g06143333
10. Apply Tooling (F) to the back of port plate (31) and install onto head assembly (26).
11. Install O-ring seal (29) onto head assembly (26).
6/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 14 g06141800
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
12. Install head assembly (26) and bolts (25). Tighten bolts (25) to a torque of 205 ± 10 N·m
(151 ± 7 lb ft).
13. Install adjustment screw (28) and the O-ring seal. Install cover (27) and the O-ring seal.
Illustration 15 g06141787
Improper assembly of parts that are spring loaded can cause bodily
injury.
7/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install spool (19), guide (20), spring (21), spring (22), O-ring seal (23), and plug (24) into
compensator valve (1).
15. Install spool (13), guide (14), spring (15), spring (16), O-ring seal (17), and plug (18) into
compensator valve (1).
16. Install gasket (12) onto compensator valve (1).
Illustration 16 g06141600
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install O-ring seals (11) onto valve group (4). Install spool (10), spring (9), guide (8), and
actuator piston (7) onto valve (4).
8/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 17 g06141568
18. Install valve (4) and the O-ring seal into main drive pump housing (6). Install solenoid (3),
nut (2), and the O-ring seal onto valve (4).
19. Install compensator valve (1) and bolts (5) onto main drive pump housing (6). Tighten bolts
(5) to a torque of 15 ± 2 N·m (132 ± 17 lb in).
End By:
a. Remove from Tooling (A).
b. Install the piston pump (main hydraulic).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 22:56:36 UTC+0800 2019
9/9
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420F BACKHOE LOADER JWJ
Configuration: 420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416F, 420F and 430F Backhoe Loaders Machine Systems
Media Number -UENR2321-04 Publication Date -01/01/2014 Date Updated -03/11/2016
i05068971
Hydraulic Tank - Remove and Install
SMCS - 4332-010; 5056-010; 5056-011; 5056-012
Removal Procedure
Start By:
a. Remove cab.
Illustration 1 g03235269
1. Disconnect hoses (2) from hydraulic tank assembly (1).
2. Disconnect clamp (3) and hose (4).
1/3
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g03235697
3. Disconnect clamp (5).
Illustration 3 g03235656
4. Remove bolts (6) and hydraulic tank assembly (1).
Illustration 4 g03235920
5. Remove strainer (7) and gauge (8) from hydraulic tank assembly (1).
6. Remove bolts (9) and bracket assembly (10) from hydraulic tank assembly (1).
2/3
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Installation Procedure
1. Install hydraulic tank assembly in the reverse order of removal.
a. Tighten bolts (9) to a torque of 50 ± 5 N·m (37 ± 3 lb ft).
b. Tighten strainer (7) to a torque of 50 ± 5 N·m (37 ± 3 lb ft).
c. Tighten gauge (8) to a torque of 8 ± 1 N·m (71 ± 9 lb in).
d. Tighten bolts (6) to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 22 22:57:32 UTC+0800 2019
3/3
420F Backhoe Loader JWJ00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2019/11/22
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...