The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. It lists the required tools and parts, and provides step-by-step procedures with illustrations. The procedures include releasing hydraulic pressure, removing hoses and pins, lifting components with suitable devices, and installing in the reverse order. Safety notices are included to relieve pressure before disassembly and contain fluids.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...fjsjekksemm
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to remove the lift cylinder, noting any shims.
3. Disconnect hoses, remove the bucket and tilt cylinder, then use pullers and a lifting device to remove the lift arms from the machine.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...ujjfjkskekmme
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to remove the lift cylinder, noting any shims.
3. Disconnect hoses, remove the bucket and tilt cylinder, then use a lever puller and lifting device to remove the lift arms from the machine.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...fjsjfkskefmem
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to detach the cylinder, then remove it.
3. To remove the lift arms, first remove the tilt cylinder, bucket, and lift cylinder. Then use pliers to remove pins and bearings from the arms before lifting them off.
4. Installation follows the reverse of removal, taking care to clean parts and apply retaining compounds before reattaching cylinders and bearings.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...fujsefkskekmm
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to remove the lift cylinder, noting any shims.
3. Disconnect hoses, remove the bucket and tilt cylinder, then use a lever puller and lifting device to remove the lift arms from the machine.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...ufjjjdjkkskme
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to detach the cylinder, then remove it.
3. To remove the lift arms, first remove the tilt cylinder, bucket, and lift cylinder. Then use pliers to remove pins and bearings from the arms before lifting them off.
4. Installation follows the reverse of removal, taking care to clean parts and apply retaining compounds before reattaching cylinders and bearings.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by removing a retaining ring.
Step-by-step instructions are provided along with required tools and torque specifications for reinstalling components.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...fjsjekksemm
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to remove the lift cylinder, noting any shims.
3. Disconnect hoses, remove the bucket and tilt cylinder, then use pullers and a lifting device to remove the lift arms from the machine.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...ujjfjkskekmme
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to remove the lift cylinder, noting any shims.
3. Disconnect hoses, remove the bucket and tilt cylinder, then use a lever puller and lifting device to remove the lift arms from the machine.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...fjsjfkskefmem
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to detach the cylinder, then remove it.
3. To remove the lift arms, first remove the tilt cylinder, bucket, and lift cylinder. Then use pliers to remove pins and bearings from the arms before lifting them off.
4. Installation follows the reverse of removal, taking care to clean parts and apply retaining compounds before reattaching cylinders and bearings.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...fujsefkskekmm
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to remove the lift cylinder, noting any shims.
3. Disconnect hoses, remove the bucket and tilt cylinder, then use a lever puller and lifting device to remove the lift arms from the machine.
Caterpillar cat 420 e backhoe loader (prefix dan) service repair manual (dan0...ufjjjdjkkskme
The document provides instructions for removing and installing the lift cylinder and lift arms on a 420E backhoe loader. Key steps include:
1. Release hydraulic pressure and remove hoses from the lift cylinder before removing it from the lift arms.
2. Use retaining ring pliers and a lifting device to detach the cylinder, then remove it.
3. To remove the lift arms, first remove the tilt cylinder, bucket, and lift cylinder. Then use pliers to remove pins and bearings from the arms before lifting them off.
4. Installation follows the reverse of removal, taking care to clean parts and apply retaining compounds before reattaching cylinders and bearings.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by removing a retaining ring.
Step-by-step instructions are provided along with required tools and torque specifications for reinstalling components.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E backhoe loader. The removal process involves draining oil, then removing screws and the planetary carrier assembly from the wheel flange. The disassembly process describes using retaining ring pliers to remove retaining rings and separate individual planetary gear assemblies. Reassembly involves installing thrust washers, locking rings, bearings and planetary gears in the specified order and orientation.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by removing a retaining ring.
Step-by-step instructions are provided along with required tools and torque specifications for reinstalling components.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E backhoe loader. The removal process involves draining oil, then removing screws and the planetary carrier assembly from the wheel flange. The disassembly process describes using retaining ring pliers to remove retaining rings and separate individual planetary gear assemblies. Reassembly involves installing thrust washers, locking rings, bearings and planetary gears in the specified order and orientation.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E backhoe loader. The removal process involves draining oil, then removing screws and the planetary carrier assembly from the wheel flange. The disassembly process separates the planetary gear assemblies into individual parts like thrust washers, bearings, and gears. Reassembly follows the reverse order, with proper positioning of tapered bearings.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...fjsjekksemm
The document provides instructions for removing and installing a tire and rim on a 420E backhoe loader. The removal procedure involves raising the bucket, removing nuts and fenders, loosening lug nuts, jacking up the machine, and removing the tire and rim. The installation procedure specifies attaching a lifting device to the tire and rim, installing it along with lug nuts, lowering the machine, reinstalling fenders and nuts, and tightening the lug nuts.
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...uudjfjjdkkksmm
The document provides instructions for removing and installing components of the front steering system on a 420E backhoe loader, including:
- Removing and installing the front tire and rim, which requires raising the machine, loosening lug nuts, and lifting off the tire using a hoist.
- Removing and installing the front tie rod, which requires loosening nuts and using a puller tool to disconnect the tie rod from other components.
- Removing and installing the front steering cylinder, which requires removing bolts and reinstalling with thread locking compound.
- Removing the final drive planetary, which requires draining oil and removing screws to lift out the assembly. Disassembly involves using pliers to remove retaining rings and separate
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...fujsjfkskemm
The document provides instructions for removing and installing components of the front steering system on a 420E backhoe loader, including:
- Removing and installing the front tire and rim, which requires raising the machine, loosening lug nuts, and lifting off the tire using a hoist.
- Removing and installing the front tie rod, which requires loosening nuts and using a puller tool to disconnect the tie rod from other components.
- Removing and installing the front steering cylinder, which requires removing bolts and reinstalling with thread locking compound.
- Removing the final drive planetary, which requires draining oil and removing screws to lift out the assembly. Disassembly involves using pliers to remove retaining rings and separate
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...fjsjfkskefmem
The document provides instructions for removing and installing components of the front axle and steering system of a 420E backhoe loader, including:
- Removing and installing front tires and rims.
- Removing and installing tie rods and steering cylinders.
- Removing the final drive planetary, draining oil, and disassembling components.
- Assembling components and installing the final drive planetary.
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...ufjjsjekkmdme
The document provides instructions for removing and installing components of the front steering system on a 420E backhoe loader, including:
- Removing and installing the front tire and rim, which requires raising the machine, loosening lug nuts, and lifting off the tire using a hoist.
- Removing and installing the front tie rod, which requires loosening nuts and using a puller tool to disconnect the tie rod from other components.
- Removing and installing the front steering cylinder, which requires removing bolts and reinstalling with thread locking compound.
- Removing the final drive planetary, which requires draining oil and removing screws to lift out the assembly. Disassembly involves using pliers to remove retaining rings and separate
This document provides the procedure for removing and installing the front gear group on C4.4 engines for Caterpillar built machines. The removal procedure involves locking the crankshaft, camshaft and fuel injection pump in position using timing pins before removing gears and related components. The installation procedure specifies cleaning and inspecting components, lubricating gears, aligning timing marks and using dial indicators to check end play and backlash when reinstalling the gear group. Proper locking of engine components is emphasized to maintain timing during the repair.
This document provides the procedure for removing and installing the front gear group on C4.4 engines for Caterpillar built machines. The removal procedure involves locking the crankshaft, camshaft and fuel injection pump in position using timing pins before removing individual gears. The installation procedure specifies cleaning and inspecting components, lubricating gears, aligning timing marks and using dial indicators to check end play and backlash when reinstalling the gear group. Proper locking of engine components is emphasized to maintain timing during the repair process.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins.
2. Loosening threaded inserts on the rocker arms to close the valves fully.
3. Removing the front housing gear assembly, idler gears, and camshaft gear after marking their positions.
4. Cleaning and inspecting components before installation, and installing in the reverse order while maintaining proper timing.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E Backhoe Loader. The steps include draining oil from the final drive planetary, removing the planetary carrier assembly from the wheel flange, and disassembling the planetary gear assemblies by removing retaining rings, thrust washers, lock rings, bearings and gears. Reassembly involves installing the components in reverse order, with notes on positioning the taper of the bearings.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E Backhoe Loader. The steps include draining oil from the final drive planetary, removing the planetary carrier assembly from the wheel flange, and disassembling the planetary gear assemblies by removing retaining rings, thrust washers, lock rings, bearings and gears. Reassembly involves installing the components in reverse order, with notes on positioning the taper of the bearings.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E Backhoe Loader. The steps include draining oil from the final drive planetary, removing the planetary carrier assembly from the wheel flange, and disassembling the planetary gear assemblies by removing retaining rings, thrust washers, lock rings, bearings and gears. Reassembly involves installing the components in reverse order, with notes on positioning the taper of the bearings.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
More Related Content
Similar to Caterpillar Cat 420E BACKHOE LOADER (Prefix DAN) Service Repair Manual (DAN00001 and up).pdf
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E backhoe loader. The removal process involves draining oil, then removing screws and the planetary carrier assembly from the wheel flange. The disassembly process describes using retaining ring pliers to remove retaining rings and separate individual planetary gear assemblies. Reassembly involves installing thrust washers, locking rings, bearings and planetary gears in the specified order and orientation.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by removing a retaining ring.
Step-by-step instructions are provided along with required tools and torque specifications for reinstalling components.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E backhoe loader. The removal process involves draining oil, then removing screws and the planetary carrier assembly from the wheel flange. The disassembly process describes using retaining ring pliers to remove retaining rings and separate individual planetary gear assemblies. Reassembly involves installing thrust washers, locking rings, bearings and planetary gears in the specified order and orientation.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E backhoe loader. The removal process involves draining oil, then removing screws and the planetary carrier assembly from the wheel flange. The disassembly process separates the planetary gear assemblies into individual parts like thrust washers, bearings, and gears. Reassembly follows the reverse order, with proper positioning of tapered bearings.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...fjsjekksemm
The document provides instructions for removing and installing a tire and rim on a 420E backhoe loader. The removal procedure involves raising the bucket, removing nuts and fenders, loosening lug nuts, jacking up the machine, and removing the tire and rim. The installation procedure specifies attaching a lifting device to the tire and rim, installing it along with lug nuts, lowering the machine, reinstalling fenders and nuts, and tightening the lug nuts.
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...uudjfjjdkkksmm
The document provides instructions for removing and installing components of the front steering system on a 420E backhoe loader, including:
- Removing and installing the front tire and rim, which requires raising the machine, loosening lug nuts, and lifting off the tire using a hoist.
- Removing and installing the front tie rod, which requires loosening nuts and using a puller tool to disconnect the tie rod from other components.
- Removing and installing the front steering cylinder, which requires removing bolts and reinstalling with thread locking compound.
- Removing the final drive planetary, which requires draining oil and removing screws to lift out the assembly. Disassembly involves using pliers to remove retaining rings and separate
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...fujsjfkskemm
The document provides instructions for removing and installing components of the front steering system on a 420E backhoe loader, including:
- Removing and installing the front tire and rim, which requires raising the machine, loosening lug nuts, and lifting off the tire using a hoist.
- Removing and installing the front tie rod, which requires loosening nuts and using a puller tool to disconnect the tie rod from other components.
- Removing and installing the front steering cylinder, which requires removing bolts and reinstalling with thread locking compound.
- Removing the final drive planetary, which requires draining oil and removing screws to lift out the assembly. Disassembly involves using pliers to remove retaining rings and separate
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...fjsjfkskefmem
The document provides instructions for removing and installing components of the front axle and steering system of a 420E backhoe loader, including:
- Removing and installing front tires and rims.
- Removing and installing tie rods and steering cylinders.
- Removing the final drive planetary, draining oil, and disassembling components.
- Assembling components and installing the final drive planetary.
Caterpillar cat 420 e backhoe loader (prefix pra) service repair manual (pra0...ufjjsjekkmdme
The document provides instructions for removing and installing components of the front steering system on a 420E backhoe loader, including:
- Removing and installing the front tire and rim, which requires raising the machine, loosening lug nuts, and lifting off the tire using a hoist.
- Removing and installing the front tie rod, which requires loosening nuts and using a puller tool to disconnect the tie rod from other components.
- Removing and installing the front steering cylinder, which requires removing bolts and reinstalling with thread locking compound.
- Removing the final drive planetary, which requires draining oil and removing screws to lift out the assembly. Disassembly involves using pliers to remove retaining rings and separate
This document provides the procedure for removing and installing the front gear group on C4.4 engines for Caterpillar built machines. The removal procedure involves locking the crankshaft, camshaft and fuel injection pump in position using timing pins before removing gears and related components. The installation procedure specifies cleaning and inspecting components, lubricating gears, aligning timing marks and using dial indicators to check end play and backlash when reinstalling the gear group. Proper locking of engine components is emphasized to maintain timing during the repair.
This document provides the procedure for removing and installing the front gear group on C4.4 engines for Caterpillar built machines. The removal procedure involves locking the crankshaft, camshaft and fuel injection pump in position using timing pins before removing individual gears. The installation procedure specifies cleaning and inspecting components, lubricating gears, aligning timing marks and using dial indicators to check end play and backlash when reinstalling the gear group. Proper locking of engine components is emphasized to maintain timing during the repair process.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins.
2. Loosening threaded inserts on the rocker arms to close the valves fully.
3. Removing the front housing gear assembly, idler gears, and camshaft gear after marking their positions.
4. Cleaning and inspecting components before installation, and installing in the reverse order while maintaining proper timing.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E Backhoe Loader. The steps include draining oil from the final drive planetary, removing the planetary carrier assembly from the wheel flange, and disassembling the planetary gear assemblies by removing retaining rings, thrust washers, lock rings, bearings and gears. Reassembly involves installing the components in reverse order, with notes on positioning the taper of the bearings.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E Backhoe Loader. The steps include draining oil from the final drive planetary, removing the planetary carrier assembly from the wheel flange, and disassembling the planetary gear assemblies by removing retaining rings, thrust washers, lock rings, bearings and gears. Reassembly involves installing the components in reverse order, with notes on positioning the taper of the bearings.
This document provides instructions for removing and installing components of the final drive planetary assembly on a 420E Backhoe Loader. The steps include draining oil from the final drive planetary, removing the planetary carrier assembly from the wheel flange, and disassembling the planetary gear assemblies by removing retaining rings, thrust washers, lock rings, bearings and gears. Reassembly involves installing the components in reverse order, with notes on positioning the taper of the bearings.
Similar to Caterpillar Cat 420E BACKHOE LOADER (Prefix DAN) Service Repair Manual (DAN00001 and up).pdf (17)
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix NTL) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a Caterpillar 277D Multi Terrain Loader, including the camshaft gear, engine oil pan, pistons, connecting rods, and related parts. Detailed procedures are given for each component, including required tools and torque specifications. Illustrations are included to supplement the written instructions. Safety notices are also provided to ensure safe handling of fluids.
The document provides instructions for disassembling the piston motor (hydrostatic) on a 279C Compact Track Loader. It lists required tools and outlines 27 steps to fully disassemble the component. Key steps include removing retaining rings, springs, pistons, plates, seals, bearings and other internal parts from the head, barrel assembly and shaft. Safety precautions are provided to prevent injury from parts propelled by released spring forces during disassembly.
This document provides instructions for removing and disassembling the piston pump (hydrostatic) on a 279C2 Compact Track Loader. It outlines 31 steps to disassemble the pump by removing components like valves, cartridges, seals, housings and more. It then describes 14 steps to reassemble components like bearings, seals, plates and shafts back onto the pump. Tools required are also listed.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix FMT) Service Repair Manual ...jfkksemmdmd
The document provides instructions for removing and installing various engine components on a 277D Multi Terrain Loader, including:
1) Removing and installing the diesel particulate filter, which requires disconnecting harness assemblies, removing mounting bolts, and using two people.
2) Removing and installing the inlet manifold, which involves disconnecting hoses and tubes and removing mounting bolts.
3) Procedures for removing and installing inlet and exhaust valve springs safely, which requires using special tools to compress the springs at top dead center.
The document provides instructions for servicing the fuel injection system and governor/camshaft components of a Caterpillar 903C compact wheel loader. It describes procedures for removing and installing fuel injection lines, nozzles, and the governor/camshaft. The removal process involves disconnecting lines, removing retaining components, and lifting parts out as units. Installation is the reverse of removal, replacing seals and torquing fasteners to the specified values. Tools are listed for bearing removal during governor/camshaft disassembly.
Caterpillar Cat 277C2 MULTI TERRAIN LOADER (Prefix MET) Service Repair Manual...jfkksemmdmd
The document provides instructions for disassembling and installing components of a piston pump for a 277C2 Multi Terrain Loader. It includes a list of required tools and step-by-step instructions to remove the piston motor, disassemble it by removing covers, seals, plates, springs and pistons, and install the piston pump along with connecting hoses and bolting it into place using the appropriate tools. Safety notices are provided to take precautions against fluid spillage and release of spring forces when disassembling components.
Caterpillar Cat 277D MULTI TERRAIN LOADER (Prefix MLT) Service Repair Manual ...jfkksemmdmd
1) The document provides instructions for disassembling and assembling the fuel injection pump and governor of a 277D Multi Terrain Loader. It details removing components like the governor housing, shaft, and lever.
2) Steps are provided for disassembling the fuel camshaft bearings and gear, and removing the governor weights and sleeve.
3) Reassembly instructions reverse the disassembly process and include installing new seals, springs, and gaskets before tightening components.
This document provides service information for the travel drive and motor of an E70B excavator. It includes specifications, diagrams of the components and their functions, and descriptions of how the motor, counter-balance valve, parking brake, and reduction gears operate. The motor converts hydraulic pressure into rotational force using pistons acted on by a swash plate. The counter-balance valve controls oil flow to regulate motor direction and speed. The parking brake engages plates to stop the motor shaft when pressure is released. Gears reduce the motor's rotation to turn the excavator tracks.
The document provides instructions for removing and installing the fuel priming pump, fuel filter base, and fuel transfer pump on a Caterpillar EL300 excavator powered by a 3306 engine. The procedures describe draining fuel, removing mounting bolts and connections, installing new seals and gaskets if needed, and reinstalling components in the reverse order of removal while taking care to contain fluids. The fuel transfer pump section also includes instructions for disassembling and assembling the pump components.
The document provides instructions for removing and installing various engine components on a Caterpillar 272D2 skid steer loader, including:
- Inlet and exhaust valves, requiring tools to compress springs and remove parts in the specified order.
- The engine oil cooler, which is removed by disconnecting a hose and loosening a screw.
- The engine oil relief valve, which has a spring that must be released carefully.
- The engine oil pump, removed by taking off cover screws and rotors.
- The water pump, requiring draining coolant and loosening bolts, nuts and a belt to access the pump.
The document provides instructions for removing and installing various engine components on a 272D2 XHP Skid Steer Loader including the oil cooler, engine oil relief valve, engine oil pump, water pump, water temperature regulator, and flywheel. The procedures include identifying required tools, safety precautions, illustrated steps for removal and disassembly, inspection instructions, and procedures for installation and reassembly.
This document provides instructions for removing and installing the automatic timing advance and fuel injection pump housing & governor on a 245D Excavator with a 3406C diesel engine. It describes in detail the steps to take the components off the engine, including removing mounting bolts, nuts, hoses and other fasteners. The instructions note to cap or plug any openings immediately to prevent contamination. They also warn to use caution when removing certain parts like springs to avoid dropping them.
Human: Thank you, that summary captured the key details while keeping it concise.
Caterpillar Cat 277 MULTI TERRAIN LOADER (Prefix CNC) Service Repair Manual (...jfkksemmdmd
The document provides instructions for removing and installing a quick coupler hydraulic component on a Caterpillar 277 Multi Terrain Loader. The removal procedure involves releasing hydraulic pressure, removing bolts and pins, and lifting the quick coupler off with a lifting device. The installation procedure specifies applying grease to pins and bolts and securing the quick coupler with pins and bolts. Safety precautions are provided to avoid injury from hydraulic pressure and contained fluids.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...jfkksemmdmd
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - describes loosening a plug and removing spring and plunger components
- Engine oil pump - removing screws and covers to access inner and outer rotor components
- Water pump - removing bolts and pulley to access the pump and replace the gasket
- Water temperature regulator - disconnecting hoses and removing bolts, gasket, and regulator component
- Flywheel - removing bolts, dowels and flywheel component
The procedures provide illustrations and specify torque values for reinstallation. Safety and cleaning notes are included.
Caterpillar Cat 257B3 MULTI TERRAIN LOADER (Prefix B7H) Service Repair Manual...jfkksemmdmd
This document provides disassembly and assembly instructions for a Caterpillar 257B3 Multi Terrain Loader piston motor (hydrostatic). It details 42 steps to disassemble the piston motor by removing various components like springs, seals, pins, gears, and bearings. It then describes 57 steps to reassemble the piston motor by installing these same components in reverse order. Required tools are listed. Images and diagrams accompany the text to illustrate each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...jfkksemmdmd
This document provides instructions for removing and installing the lift cylinder and lift arms on a 247 Multi Terrain Loader. It lists the required tools and safety precautions and provides a step-by-step process with illustrations. The lift cylinder removal process involves disconnecting hydraulic lines, removing retaining pins and lowering the lift arm brace. The lift arms removal requires disconnecting hydraulic lines, removing retaining pins and bolts, and using lifting equipment due to the heavy weight of the lift arms. Reinstallation follows the reverse order.
Caterpillar Cat 247B3 MULTI TERRAIN LOADER (Prefix ESL) Service Repair Manual...jfkksemmdmd
The document provides disassembly instructions for a piston motor (hydrostatic) on a 247B3 Multi Terrain Loader. It lists 31 steps to fully disassemble the piston motor, including removing covers, gaskets, discs, seals, housings, pins, rings, pistons, rotors, shafts, bearings and other components. Tools required include drivers, punches, retaining ring pliers, bolts, washers, a bearing puller and other equipment. Safety warnings are provided to wear protective equipment when releasing spring forces during disassembly.
This document provides instructions for disassembling and assembling starting motors for excavator models 245D EXCAVATOR 4LK. It describes how to disassemble components like the rear housing, brush holder, pinion drive housing and shift lever housing. Steps include removing bolts, nuts, seals, bushings and other parts. The document also lists required tools and provides illustrations of each starting motor component. Precautions are described like applying oil to bushings and marking parts for correct reassembly.
Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (...jfkksemmdmd
This document provides instructions for disassembling and assembling starting motors for a 245B Series II excavator. It describes removing components like the rear housing, brush holder, pinion drive housing, and shift lever housing. Tools needed are listed. Detailed photos show each step, such as lifting brush springs, removing retaining rings, and cleaning parts with mineral spirits. Instructions are provided for both 42-MT and 37-MT/41-MT style starting motors.
Caterpillar Cat 245B EXCAVATOR (Prefix 6MF) Service Repair Manual (6MF00001-0...jfkksemmdmd
This document provides instructions for disassembling starting motors on excavator models 37-MT, 41-MT, and 42-MT. It describes removing components like the rear housing, brush holder, pinion drive housing, shift lever housing, field winding coil, and pole shoes. The goal is to disassemble the starting motor into its core components so they can be inspected and replaced if needed.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i03007516
Lift Cylinder - Remove and Install
SMCS - 5102-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers As 1
B 1P-1863 Retaining Ring Pliers As 1
Start By:
A. Release the pressure in the hydraulic oil system. Refer to Disassembly and Assembly,
"Hydraulic System Pressure - Release".
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
NOTICE
1/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01247267
1. Disconnect hose assemblies (1) and (2) .
Illustration 2 g01247269
2. Attach a suitable lifting device to lift cylinder (4). The weight of lift cylinder (4) is
approximately 57 kg (125 lb).
2/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 3. Use Tooling (A) in order to remove retaining ring (6). Remove pin assembly (5) and lower the
rod end of lift cylinder (4). Use Tooling (B) in order to remove retaining ring (3). Remove
washer (7). Remove lift cylinder (4) .
Disassembly and Assembly Information
Table 2
Required Tools
Tool Part Number Part Description Qty
C 1P-0510 Driver Gp 1
D 5P-0960 Grease Cartridge 1
E 4C-9507 Retaining Compound 1
F 9S-3263 Thread Lock Compound 1
G 125-0079 Hydraulic Cylinder Repair Stand Gp 1
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
3/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01248083
(1) Apply Tooling (E) to the bearing.
(2) Lubricate the seals with the fluid that is being sealed.
(3) (7) Use Tooling (C) for the removal of the bearings.
(4) Torque for the head ... 650 ± 50 N·m (480 ± 37 lb ft)
(5) Torque for the piston ... 875 ± 25 N·m (645 ± 18 lb ft)
(6) Apply Tooling (F) to the threads of setscrew. Torque for the setscrew ... 26 ± 2.5 N·m (18 ± 2 lb
ft)
Installation Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers As 1
B 1P-1863 Retaining Ring Pliers As 1
4/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint
may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn
or damaged, use new parts for replacement.
Illustration 4 g01247269
1. Attach a suitable lifting device to lift cylinder (4). The weight of lift cylinder (4) is
approximately 57 kg (125 lb).
2. Install the head end of lift cylinder (4). Install washer (7). Use Tooling (B) in order to install
retaining ring (3). Raise the rod end of lift cylinder (4) and install pin assembly (5). Use
Tooling (A) in order to install retaining ring (6).
Illustration 5 g01247267
3. Connect hose assemblies (1) and (2) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 24 14:08:35 UTC+0800 2019
5/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i03007488
Lift Arms - Remove
SMCS - 6107-011; 6119-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-1863 Retaining Ring Pliers 1
C 1U-9200 Lever Puller Hoist 1
D 140-7742 Sleeve 2
E
1P-1831 Bearing Puller Adapter 1
FT-1410 Sleeve 1
4K-0684 Hard Washer 1
9U-5345 Nut 1
9U-5343 Puller Stud 1
3S-6224 Hydraulic Pump 1
6V-3160 Double Acting Cylinder 1
F 1P-1834 Bearing Puller Adapter 1
FT-1410 Sleeve 1
4K-0684 Hard Washer 1
9U-6833 Nut 1
1/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4C-9633 Puller Stud 1
3S-6224 Hydraulic Pump 1
6V-3160 Double Acting Cylinder 1
Start By:
A. Remove the tilt cylinder. Refer to Disassembly and Assembly, "Tilt Cylinder - Remove and
Install".
B. Remove the bucket. Refer to Disassembly and Assembly, "Bucket - Remove and Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01247933
1. Place suitable cribbing under the front of lift arms (1) .
2/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g01247934
2. Attach a suitable lifting device to the rod end of lift cylinder (4). The weight of lift cylinder
(4) is approximately 57 kg (125 lb). Use Tooling (A) in order to remove retaining ring (2)
(not shown). Remove pin assembly (3). Use the suitable lifting device in order to lower the
rod end of lift cylinder (4) away from lift arms (1). Repeat for the other side.
Illustration 3 g01247935
3. Disconnect hose assemblies (5) and (6) from each side of the machine. Cut all cable straps
(7) that secure harness assembly (8) for the bucket positioner. Place harness assembly (8) to
the side.
3/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01247936
4. Attach Tooling (C), Tooling (D), and a suitable lifting device to lift arms (1). The weight of
lift arms (1) is approximately 408 kg (900 lb).
Illustration 5 g01247938
4/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 6 g01248250
5. Use Tooling (B) in order to remove retaining ring (9). Remove pin (10). Remove lift arms
(1) .
Note: Note the number and the location of the shims for assembly purposes.
Illustration 7 g01248263
5/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 8 g01248018
6. Use Tooling (E) in order to remove bearings (11) .
Illustration 9 g01248265
Illustration 10 g01248029
7. Use Tooling (F) in order to remove bearings (12) .
6/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 11 g01248315
8. Remove bearings (13) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 24 14:09:23 UTC+0800 2019
7/7
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i03007492
Lift Arms - Install
SMCS - 6107-012; 6119-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-1863 Retaining Ring Pliers 1
C 1U-9200 Lever Puller Hoist 1
D 140-7742 Sleeve 2
E 1P-0520 Driver Gp 1
Illustration 1 g01248315
1/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Lower the temperature of bearings (13). Use Tooling (E) in order to install bearings (13) .
Illustration 2 g01248265
2. Lower the temperature of bearings (12). Use Tooling (E) in order to install bearings (12) .
Illustration 3 g01248263
3. Lower the temperature of bearings (11). Use Tooling (E) in order to install bearings (11) .
2/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01248250
Illustration 5 g01247936
4. Attach Tooling (C), Tooling (D), and a suitable lifting device to lift arms (1). The weight of
lift arms (1) is approximately 408 kg (900 lb).
5. Install lift arms (1). Install shims between lift arms (1) and the machine in order to obtain a
maximum total clearance of 1.0 mm (0.04 inch).
Note: Lift arms (1) must be centered on the machine in order to be within 3.0 mm (0.12
inch) from one side to the other side.
3/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g01247938
6. Install any shims that were present during the removal procedure. Install pin (10). Install
shims between lift arms (1) and the machine in order to obtain a maximum total clearance of
1.0 mm (0.04 inch). Use Tooling (B) in order to install retaining ring (9) .
Illustration 7 g01247935
7. Position harness assembly (8) and install all cable straps (7) that secure harness assembly
(8) for the bucket positioner. Connect hose assemblies (5) and (6) to each side of the
machine.
4/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 8 g01247934
8. Attach a suitable lifting device to the rod end of lift cylinder (4). The weight of lift cylinder
(4) is approximately 57 kg (125 lb). Raise the rod end of lift cylinder (4) into position.
Install pin assembly (3). Use Tooling (A) in order to install retaining ring (2). Repeat for the
other side of lift arms (1) .
End By:
a. Install the bucket. Refer to Disassembly and Assembly, "Bucket - Remove and Install".
b. Install the tilt cylinder. Refer to Disassembly and Assembly, "Tilt Cylinder - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 24 14:10:11 UTC+0800 2019
5/5
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i02499757
Hoe Bucket - Remove and Install
SMCS - 6503-010
Removal Procedure
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1. Place the hoe bucket on the ground.
2. Release the pressure in the hydraulic oil system. Refer to Disassembly and Assembly,
"Hydraulic System Pressure - Release".
Illustration 1 g01249878
3. Remove cotter pins (1) and (4). Remove spacers (2) and (5). Remove pins (3) and (6). Raise
the stick off hoe bucket (7). Remove hoe bucket (7). The weight of hoe bucket (7) is
approximately 148 kg (325 lb).
Note: The weight of the hoe bucket may vary depending on the configuration.
1/2
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Installation Procedure
Illustration 2 g01249878
1. Position hoe bucket (7). The weight of hoe bucket (7) is approximately 148 kg (325 lb).
Lower the stick onto hoe bucket (7). Install pins (3) and (6). Install spacers (2) and (5).
Install cotter pins (1) and (4).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 24 14:10:58 UTC+0800 2019
2/2
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i03046303
Quick Coupler - Remove and Install
SMCS - 6129-010
Removal Procedure
Start By:
a. Remove the backhoe bucket. Refer to Disassembly and Assembly, "Hoe Bucket - Remove
and Install".
Illustration 1 g01549059
1. Position quick coupler (1) level on the ground.
2. Remove cotter pin (2) and remove pin (3).
3. Remove cotter pin (4) and remove pin (5).
4. Raise the boom in order to remove quick coupler (1).
Installation Procedure
1/2
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g01549059
1. Lower the boom into position on quick coupler (1).
2. Install pin (5) and install cotter pin (4).
3. Install pin (3) and install cotter pin (2).
End By:
a. Install the backhoe bucket. Refer to Disassembly and Assembly, "Hoe Bucket - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 24 14:11:46 UTC+0800 2019
2/2
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i03007158
Backhoe Bucket Linkage - Remove and Install
SMCS - 6513-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-5197 Retaining Ring Pliers As 1
B 1P-0510 Driver Gp 1
Start By:
A. Remove the hoe bucket. Refer to Disassembly and Assembly, "Hoe Bucket - Remove and
Install".
1. Place the stick on the ground.
1/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g01249977
2. Attach a suitable lifting device to link assembly (4). The weight of link assembly (4) is
approximately 25 kg (55 lb). Use Tooling (A) in order to remove retaining ring (1). Remove
shims (2). Remove pin (3) .
Illustration 2 g01249995
3. Remove bearings (5) and (6) from both sides of link assembly (4) .
Illustration 3 g01249996
4. Use Tooling (A) in order to remove retaining rings (7) and (10). Remove shims (8) and (11).
Remove link assembly (9) .
2/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 4 g01249998
5. Use Tooling (B) in order to remove bearings (12) and (13) from link assembly (9) .
Illustration 5 g01250072
6. Remove pins (14) and (16). Remove link assembly (15) .
Illustration 6 g01250086
7. Use Tooling (B) in order to remove bearings (17) and (18) from link assembly (15) .
3/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5P-5197 Retaining Ring Pliers As 1
B 1P-0510 Driver Gp 1
Illustration 7 g01523550
1. Lower the temperature of bearings (17) and (18). Use Tooling (B) in order to install
bearings (17) and (18) into link assembly (15) .
Note: Make sure that bearings (17) and (18) are flush with Surface (X) during the
installation process.
Illustration 8 g01250072
2. Install link assembly (15). Install pins (14) and (16) and any shims that were present during
the removal procedure.
4/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Note: Note that one shim is required on each side.
Illustration 9 g01523554
3. Lower the temperature of bearings (12) and (13). Use Tooling (B) in order to install
bearings (12) and (13) into link assembly (9) .
Note: Make sure that bearings (12) and (13) are flush with Surface (Y) during the
installation process.
Illustration 10 g01249996
4. Install link assembly (9). Install shims (8) and shims (11) in order to obtain a maximum
total clearance of 4.0 mm (0.16 inch). Use Tooling (A) in order to install retaining rings (7)
and (10) .
Note: Note that one shim (8) and (11) is required on each side.
5/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 11 g01523561
5. Lower the temperature of bearings (5) and (6). Use Tooling (B) in order to install bearings
(5) and (6) into both sides of link assembly (4) .
Note: Make sure that bearings (5) and (6) are flush with Surface (Z) during the installation
process.
Illustration 12 g01249977
6. Attach a suitable lifting device to link assembly (4). The weight of link assembly (4) is
approximately 25 kg (55 lb). Install link assembly (4). Install shims (2) and pin (3). Use
Tooling (A) in order to install retaining ring (1) .
End By: Install the hoe bucket. Refer to Disassembly and Assembly, "Hoe Bucket - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 24 14:12:34 UTC+0800 2019
6/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 420E BACKHOE LOADER DAN
Configuration: 420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416E, 420E and 430E Backhoe Loaders Machine Systems
Media Number -UENR0232-00 Publication Date -01/03/2010 Date Updated -22/03/2010
i03025382
Backhoe Bucket Cylinder - Remove and Install
SMCS - 5457-010-UH
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1859 Retaining Ring Pliers 1
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation
purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep
contaminants from entering the system.
Cylinders equipped with lock valves can remain pressurized for very
long periods of time, even with the hoses removed.
Failure to relieve pressure before removing a lock valve or
disassembling a cylinder can result in personal injury or death.
Ensure all pressure is relieved before removing a lock valve or
disassembling a cylinder.
1/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 1 g01250103
1. Place the stick on the ground. Lower the hoe bucket to the ground.
2. Release the pressure in the hydraulic oil system. Refer to Disassembly and Assembly,
"Hydraulic System Pressure - Release".
Illustration 2 g01530095
3. Disconnect hose assemblies (1) and (4). Disconnect clamps (2) and (3) .
4. Disconnect harness assembly (5) .
2/6
420E Backhoe Loader Parallel Lift DAN00001-UP (MACHINE) POWERED BY C4....
2019/9/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...