This document provides the procedure for removing and installing the front gear group on C4.4 engines for Caterpillar built machines. The removal procedure involves locking the crankshaft, camshaft and fuel injection pump in position using timing pins before removing gears and related components. The installation procedure specifies cleaning and inspecting components, lubricating gears, aligning timing marks and using dial indicators to check end play and backlash when reinstalling the gear group. Proper locking of engine components is emphasized to maintain timing during the repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312E L EXCAVATOR WEY
Configuration: 312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i04048571
Gear Group (Front) - Remove and Install - Heavy Duty Gear
Group (Front)
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107
Timing Pin
(Fuel Injection Pump)
1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40Torx Socket 1
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
NOTICE
1/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the front gear group. Carefully follow the procedure in order to remove the gear
group.
1. If the air compressor is equipped with a hydraulic pump, remove the hydraulic pump. Refer
to Original Equipment Manufactures (OEM) for the correct procedure.
2. If the engine is equipped with an air compressor, remove the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Remove" for the correct procedure.
3. If the engine is equipped with only a hydraulic pump, remove the hydraulic pump. Refer to
OEM for the correct procedure.
4. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
2/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g02486477
5. Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
6. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke.
7. Remove Tooling (D).
8. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
3/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 2 g02048655
9. Use Tooling (E) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew
threaded inserts (4) on all rocker arms (3) until all valves are fully closed. Ensure that the
guides (5) for the pushrods are left in position on the threaded inserts (4).
Note: Ensure that ALL threaded inserts are fully unscrewed.
10. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to Illustration 1.
4/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g02488136
11. Install Tooling (B) through Hole (X) in camshaft gear (6) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
12. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
5/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g02052394
13. If the right-hand side of the engine is equipped with a hydraulic pump, remove the hydraulic
pump. Refer to OEM for the correct procedure.
14. If necessary, remove bolts (7) from plate (8). Remove plate (8) and remove O-ring seal (9).
15. Remove circlip (10) and remove gear assembly (11) from front housing (12).
6/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 5 g02053673
16. If necessary, follow Step 16.a through Step 16.b in order to disassemble gear assembly (11).
a. Remove circlip (13) from gear assembly (11).
b. Place gear assembly (11) on a suitable support. Press bearing (14) from gear (15).
7/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 6 g02048714
17. Mark gear (6), gear (16), gear (17) and gear (18) in order to show alignment. Refer to
Illustration 6.
Note: Identification will ensure that the gears can be installed in the original alignment.
18. Remove camshaft gear (6). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
8/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 7 g02053984
19. Remove bolts (22) and bolts (24).
20. Remove tube assembly (23) from idler gear (16) and idler gear (26).
21. Remove plate (21).
22. Remove idler gear (16) from hub (20) (not shown).
23. Remove idler gear (26) and idler gear hub (25) from front housing (12).
24. Remove hub (20) (not shown) from front housing (12).
25. If necessary, remove bearing (19) from front housing (12). Refer to Disassembly and
Assembly, "Housing (Front) - Remove" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
9/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 Timing Pin(Fuel Injection Pump) 1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40Torx Socket 1
F 207-1601 Rubber Lubricant 1
G 7M-7456 Bearing Mount Compound 1
H
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston"
for the correct procedure.
10/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 8 g02488176
2. If necessary, install Tooling (D) into Hole (W) in the cylinder block. Use Tooling (D) in
order to lock the crankshaft in the correct position. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
3. Ensure that all of the components of the front gear group are clean and free from wear and
damage. If necessary, replace any components that are worn or damaged.
11/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 9 g02048660
12/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 10 g02053693
4. If necessary, Install bearing (19) to front housing (12). Refer to Disassembly and Assembly,
"Housing (Front) - Install" for the correct procedure.
5. Install hub (20) to the recess of front housing (12). Ensure that the oil Hole (Y) is to the top
of the hub.
6. Ensure that the fuel injection pump is locked in the correct position. Refer to Disassembly
and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
7. Lubricate idler hub (20) with clean engine lubricating oil. Install idler gear (16) to the idler
hub. Ensure that the timing marks are toward the front of the idler gear. Align timing marks
on idler gear (16) with gear (17) and gear (18).
8. Lubricate idler gear hub (25) with clean engine lubricating oil and install idler gear (26) to
the idler gear hub. Install the assembly for idler gear (26) to front housing (12).
Note: Ensure that the idler gear hub and the idler gear are correctly aligned.
9. Position plate (21) onto idler gear (16).
Note: Ensure that the identification mark TOP is upward.
10. Position tube assembly (23) onto idler gear (16) and idler gear (26). Install bolts (22) and
bolts (24).
Note: Ensure that the tube is correctly positioned on the hubs of the idler gears.
13/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 11. Tighten bolts (22) and bolts (24) to a torque of 44 N·m (32 lb ft).
Illustration 11 g02488178
14/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 12 g02488136
12. Install camshaft gear (6). Loosely install bolt (28) and washer (27) for the camshaft gear.
Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install" for the correct
procedure.
13. Install Tooling (B) through Hole (X) in camshaft gear (6) into the front housing.
15/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 13 g02488216
14. Ensure that the timing marks on gear (6), gear (16), gear (17) and gear (18) are in alignment
and that the mesh of the gears is correct.
15. Remove Tooling (B), Tooling (C), and Tooling (D).
16. When bolt (28) is a 8.8 Grade. Tighten bolt (28) for camshaft gear (6) to a torque of 95 N·m
(70 lb ft).
When bolt (28) is a 10.9 Grade. Tighten bolt (28) to a torque of 120 N·m (89 lb ft).
17. Use Tool (H) in order to check the end play of the camshaft gear. Refer to Specifications,
"Camshaft" for more information.
18. Use Tool (H) in order to check the end play of the idler gears. Refer to Specifications, "Gear
Group (Front)" and refer to Disassembly and Assembly, "Idler Gear - Remove and Install"
for further information.
19. Use Tooling (H) in order to measure the backlash for gear (6), gear (16), gear (17) and gear
(16). Refer to Specifications, "Gear Group (Front)" for further information.
16/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 14 g02058193
20. If necessary, follow Step 20.a through Step 20.c in order to assemble gear assembly (10).
a. Apply a small continuous bead of Tooling (G) to inner Surface (Z) of bearing (14).
Place the inner race of bearing (14) onto a suitable support. Press the shaft of gear
(15) into bearing (14) until the shoulder of the gear is against the bearing. Remove
any excess bearing mount compound.
b. Install circlip (13) to gear assembly (11).
c. Lightly lubricate bearing (14) and gear assembly (11) with clean lubricating oil.
17/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g02052394
21. Install gear assembly (11) to front housing (12). Ensure that the shaft of gear assembly (11)
is correctly aligned with the bearing in front housing (12).
22. Install circlip (10) to front housing (12).
Note: Ensure that the circlip is correctly located in the front housing.
23. Ensure that there is tactile backlash between the camshaft gear and the accessory drive gear.
24. If the right-hand side of the engine is equipped with a hydraulic pump, install the hydraulic
pump. Refer to OEM for the correct procedure.
25. If necessary, lightly lubricate a new O-ring seal (9) with Tooling (F). Install new O-ring seal
(9) to plate (8). Install plate (8) to front housing (12).
26. Install bolts (7) to plate (8). Tighten the bolts to a torque of 10 N·m (88 lb in).
27. Lubricate each gear with clean engine oil.
NOTICE
Failure to ensure that the crankshaft is positioned at the safe position
will result in interference between the pistons and the valves.
18/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Interference between the pistons and the valves will result in damage to
the engine.
28. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
Illustration 16 g02048655
29. Ensure that the guides (5) for the pushrods are correctly positioned on the threaded inserts
(4). Use Tooling (E) in order to tighten threaded inserts (4) on all rocker arms (3). Tighten
the threaded inserts to a torque of 30 N·m (265 lb in).
Note: When the threaded insert is tightened, the threaded insert must be correctly seated
into the cup for the pushrod.
30. If the engine is equipped with an air compressor, install the air compressor. Refer to
Disassembly and Assembly, "Air Compressor - Install" for the correct procedure.
31. If the air compressor is equipped with a hydraulic pump, install the hydraulic pump. Refer
to OEM for the correct procedure.
32. If the engine is equipped only with a hydraulic pump, install the hydraulic pump. Refer to
OEM for the correct procedure.
19/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 33. The engine should not be operated for a period 30 minutes after the threaded inserts on all
the rocker arms have been tightened. This period of time will allow the hydraulic lifters to
purge off excessive engine oil from the hydraulic lifters.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 12 23:01:14 UTC+0800 2020
20/20
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 En...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 312E L EXCAVATOR WEY
Configuration: 312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR0602-11 Publication Date -01/08/2013 Date Updated -25/10/2017
i04048572
Gear Group (Front) - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107
Timing Pin
(Fuel Injection Pump)
1
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40Torx Socket 1
Start By:
a. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install" for the correct procedure.
NOTICE
1/15
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Note: Care must be taken in order to ensure that the fuel injection pump timing is not lost during
the removal of the front gear group. Carefully follow the procedure in order to remove the gear
group.
Illustration 1 g02485936
2/15
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 1. Remove plug (1) from the cylinder block. Remove O-ring seal (2) from the plug.
2. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke.
3. Remove Tooling (D).
4. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
Illustration 2 g01992077
5. Use Tooling (E) in order to loosen threaded inserts (4) on all rocker arms (3). Unscrew
threaded inserts (4) on all rocker arms (3) until all valves are fully closed. Ensure that the
guides (5) for the pushrods are left in position on the threaded inserts (4).
Note: Ensure that ALL threaded inserts are fully unscrewed.
6. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure. Install Tooling (D)
through Hole (W) in order to lock the crankshaft so that number one piston is at top dead
center on the compression stroke. Refer to Illustration 1.
3/15
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 3 g02485937
7. Install Tooling (B) through Hole (X) in camshaft gear (6) into the front housing. Use
Tooling (B) in order to lock the camshaft in the correct position. Refer to System Operation,
Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct
procedure.
8. Install Tooling (D) into Hole (W) in the cylinder block. Use Tooling (D) in order to lock the
crankshaft in the correct position. Refer to System Operation, Testing and Adjusting,
"Finding Top Center Position for No.1 Piston" for the correct procedure.
Note: Do not use excessive force to install Tooling (D). Do not use Tooling (D) to hold the
crankshaft during repairs.
9. Use Tooling (C) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
4/15
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 4 g01992078
10. Mark gear (6), gear (7), gear (8) and gear (9) in order to show alignment. Refer to
Illustration 4.
Note: Identification will ensure that the gears can be installed in the original alignment.
11. Remove camshaft gear (6). Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install" for the correct procedure.
12. Remove idler gear (7). Refer to Disassembly and Assembly, "Idler Gear - Remove and
Install" for the correct procedure.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 364-9107 1
5/15
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Timing Pin
(Fuel Injection Pump)
D
136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The fuel injection pump must remain locked until the procedure instructs you to unlock the
fuel injection pump.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston"
for the correct procedure.
6/15
312E & 312E L Excavators WEY00001-UP (MACHINE) POWERED BY C4.4 Engin...
2020/6/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...