Caterpillar Cat 385B Excavator (Prefix ANS) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
385B Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 385B EXCAVATOR ANS
Configuration: 385B Excavator ANS00001-UP (MACHINE) POWERED BY 3456 Engine
Disassembly and Assembly
385B and 5090B Excavators Excavator Systems
Media Number -RENR5407-06 Publication Date -01/02/2016 Date Updated -12/02/2016
i01653627
Control Valve - Disassemble - Attachment, Bucket, and Boom
SMCS - 5051-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1862 Pliers 1
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1/12
385B Excavator ANS00001-UP (MACHINE) POWERED BY 3456 Engine(SEBP325...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g00853759
1. Remove bolts (1) and cover (2).
2. Remove O-ring seals (3) and (4).
3. Remove flow compensator valves (5).
2/12
2020/10/25

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Disassemble the flow compensator valves. Remove springs (6), sleeves (7), springs (8), and
valves (9).
5. Remove line relief valves (10).
3/12
2020/10/25

6. Remove line relief valve (11).
7. Disassemble line relief valves (10) and (11). Remove O-ring seals (13), (14), (15), (17), and
(18). Remove backup rings (12) and (16).
4/12
2020/10/25

Note: Only the O-ring seals and the backup rings in the relief valves are serviceable.
However, the line relief valves may be disassembled for cleaning.
8. Remove bolts (21) and bracket assembly (20). Use a hoist and a lifting sling to support
actuator group (23). Remove bolts (22), actuator group (23), and spacer (19). The weight of
the actuator group is approximately 28 kg (60 lb).
9. Remove bolts (25) and bracket assembly (24). Use a hoist and a lifting sling to support
actuator group (26). Remove bolts (27) and actuator group (26). The weight of the actuator
group is approximately 28 kg (60 lb).
5/12
2020/10/25

10. Disassemble spacer (19). Remove O-ring seals (28) and (31). Remove plugs and O-ring
seals (30). Remove pistons (29).
11. Remove bolts (32).
12. Remove solenoid (36), O-ring seal (35), spring (34), and valve (33).
6/12
2020/10/25

14. Position the manifold in a press and apply slight pressure. Use Tooling (A) to remove
retaining ring (39).
15. Remove retainer (43) and springs (40), (41), and (42). Disassemble all of the solenoid
assemblies.
7/12
2020/10/25

16. Remove differential valve (44).
17. Remove O-ring seals (46), (47), and (49). Remove backup rings (45) and (48).
8/12
2020/10/25

18. Disassemble differential relief valves. Remove plug (50), O-ring seal (51), spacers (52),
spring (53), and valve (54) from body (55).
19. Remove resolver valve (57). Remove plugs and O-ring seals (56).
9/12
2020/10/25

20. Disassemble resolver valve (57). Remove O-ring seals (58), (61), and (62). Remove backup
rings (59) and (60).
22. Remove plug (65) and the O-ring seal. Remove O-ring seals (66).
10/12
2020/10/25

23. Remove plugs and O-ring seals (67). Remove stems (68), (69), and (70). Remove resolver
(71).
24. Disassemble resolver (71). Remove seat (72) and O-ring seals (75), (77), and (78). Remove
backup rings (76) and (79). Remove ball (73) from valve (74).
11/12
2020/10/25

25. Remove the remainder of the plugs and O-ring seals (80).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 25 10:01:14 UTC+0800 2020
12/12
2020/10/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01668635
Control Valve - Disassemble - Right Travel, Left Travel, and
Stick
SMCS - 5051-015
Table 1
Required Tools
A 1P-1862 Pliers 1
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
1/12
2020/10/25

3. Remove load check valves (5) and (6) and flow compensator valve (7).
2/12
2020/10/25

4. Disassemble flow compensator valve (7). Remove spring (8), sleeve (9), and spring (10)
from valve (11).
5. Disassemble load check valves (5) and (6). Remove boss (14) and spring (13) from valve
(12).
6. Remove relief valve (15).
3/12
2020/10/25

7. Disassemble relief valve (15). Remove O-ring seals (16), (18), (19), (21), and (22). Remove
backup rings (17) and (20).
Note: Only the O-ring seals and the backup rings in the relief valves are serviceable.
However, the line relief valves may be disassembled for cleaning.
8. Use a hoist and a lifting sling to support actuator (26). Remove bolts (23) and bracket (24).
Remove bolts (25) and actuator (26). The weight of the actuator is approximately 28 kg
(60 lb). Remove resolver valve (27).
4/12
2020/10/25

9. Use a hoist and a lifting sling to support actuator (31). Remove bolts (28) and bracket (29).
Remove bolts (30) and actuator (31). The weight of the actuator is approximately 28 kg
(60 lb). Remove spacer (32).
10. Disassemble spacer (32). Remove O-ring seals (33) and (34). Remove plugs and O-ring
seals (36). Remove pistons (35).
11. Remove bolts (37).
5/12
2020/10/25

12. Remove solenoid (41), O-ring seal (40), spring (39), and valve (38).
14. Position the manifold in a press and apply slight pressure. Use Tooling (A) to remove
retaining ring (44).
6/12
2020/10/25

15. Remove retainer (48) and springs (45), (46), and (47). Disassemble all of the solenoid
assemblies.
16. Remove differential valve (49).
7/12
2020/10/25

17. Remove O-ring seals (51), (52), and (54). Remove backup rings (50) and (53).
8/12
2020/10/25

18. Disassemble differential relief valves. Remove plug (55), O-ring seal (56), spacers (57),
spring (58), and valve (59) from body (60).
9/12
2020/10/25

20. Remove plug (63) and the O-ring seal. Remove O-ring seals (64).
21. Remove plugs and O-ring seals (65). Remove resolver valves (66).
22. Disassemble resolver valves (66). Remove O-ring seals (67), (68), and (69), and backup
rings (70) and (71).
10/12
2020/10/25

23. Disassemble resolver valve (27). Remove seat (72) and ball (74). Remove O-ring seals (73),
(75), and (76). Remove backup rings (77) and (78).
24. Remove plugs and O-ring seals (79). Remove spools (80), (81), and (82).
11/12
2020/10/25

25. Remove plugs and O-ring seals (83).
Sun Oct 25 10:02:10 UTC+0800 2020
12/12
2020/10/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01674415
Control Valve - Disassemble - Proportional Valve
SMCS - 5051-015
1. Remove bolts (1) and valve group (2).
1/2
2020/10/25

2. Remove nut (3) and solenoid (4).
3. Remove bolt (5) and bracket assembly (6). Remove cartridge (7).
4. Remove O-ring seals (8) from cartridge (6).
Sun Oct 25 10:03:07 UTC+0800 2020
2/2
2020/10/25

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01659183
Control Valve - Assemble - Attachment, Bucket, and Boom
SMCS - 5051-012
Assembly Procedure
Table 1
Required Tools
A 1P-1862 Pliers 1
1. Install plugs and O-ring seals (80).
1/12
2020/10/25

2. Assemble resolver (71). Install ball (73) in valve (74). Install seat (72). Install backup rings
(76) and (79). Install O-ring seals (75), (77), and (78).
Note: Reduce the temperature of seat (72) before inserting the seat into the bore of valve
(74).
3. Install resolver (71). Tighten the resolver to a torque of 50 ± 10 N·m (37 ± 7 lb ft). Install
stems (68), (69), and (70). Install plugs and O-ring seals (67).
2/12
2020/10/25

4. Install O-ring seals (66). Install plug (65) and the O-ring seal.
5. Position cover (64) and install bolts (63).
6. Assemble resolver valve (57). Install backup rings (59) and (60). Install O-ring seals (58),
(61), and (62).
3/12
2020/10/25

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

7. Install plugs and O-ring seals (56). Install resolver valve (57). Tighten the resolver valve to
a torque of 50 ± 10 N·m (37 ± 7 lb ft).
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/12
2020/10/25

8. Install O-ring seal (51), spacers (52), spring (53), and valve (54) in body (55). Install plug
(50).
9. Install backup rings (45) and (48). Install O-ring seals (46), (47), and (49).
5/12
2020/10/25

Caterpillar Cat 385B Excavator (Prefix ANS) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 385B Excavator (Prefix ANS) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 385B Excavator (Prefix ANS) Service Repair Manual Instant Download.pdf (7)

More from jiazhi27185

More from jiazhi27185 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 385B Excavator (Prefix ANS) Service Repair Manual Instant Download.pdf